On electro-acoustic characteristics of a marine broadband sparker for seismic exploration

The construction of major marine infrastructure projects and the exploration and development of deep-sea mineral resources require fine imaging of seabed strata and structures.The highresolution marine seismic exploration based on a high broadband sparker source is an important approach to reveal seabed stratum and reservoir structure,and identify geohazard.To optimize the performance of sparker seismic source,we investigated the electro-acoustic characteristics of spark discharge under conditions of different charging voltages and electrode numbers.Results show that the sound source level increased with the increase of the charging voltage,whereas the main frequency decreased when the charging voltage increases.In addition,it was found that the charging capacitance had more obvious influence on the main frequency than the sound source level did.Although the load energy decreased with increasing electrode number,the sound source level still increased but the main frequency decreased.Meanwhile,the primary to bubble(P/B)ratio increased with the increase of the electrode number.To gain a deeper insight into the electro-acoustic characteristics,we investigate the relationship between sound source level and power peak,from which a good correlation was observed.A more practical statistical analysis on the rise rate of current was processed,and a perfect logarithmic function was derived.Furthermore,we found that the main frequency was most possibly subjected to the electrical energy,especially the charging energy per electrode.The results indicate that the charging energy per electrode less than 10 J could increase the main frequency to above 300 Hz.At last,the main frequency could be reduced to 20 Hz when the charging energy of a single-electrode discharge was enhanced to over 4 kJ.This study shall be helpful in developing a sparker seismic source and improving the performance for marine engineering exploration and geohazard assessment.

Accurate Source-Receiver Positioning Method for a High-Resolution Deep-Towed Multichannel Seismic Exploration System

The near-seabed multichannel seismic exploration systems have yielded remarkable successes in marine geological disaster assessment,marine gas hydrate investigation,and deep-sea mineral exploration owing to their high vertical and horizontal resolution.However,the quality of deep-towed seismic imaging hinges on accurate source-receiver positioning information.In light of existing technical problems,we propose a novel array geometry inversion method tailored for high-resolution deep-towed multichannel seismic exploration systems.This method is independent of the attitude and depth sensors along a deep-towed seismic streamer,accounting for variations in seawater velocity and seabed slope angle.Our approach decomposes the towed line array into multiline segments and characterizes its geometric shape using the line segment distance and pitch angle.Introducing optimization parameters for seawater velocity and seabed slope angle,we establish an objective function based on the model,yielding results that align with objective reality.Employing the particle swarm optimization algorithm enables synchronous acquisition of optimized inversion results for array geometry and seawater velocity.Experimental validation using theoretical models and practical data verifies that our approach effectively enhances source and receiver positioning inversion accuracy.The algorithm exhibits robust stability and reliability,addressing uncertainties in seismic traveltime picking and complex seabed topography conditions.

Review of Artificial Intelligence for Oil and Gas Exploration: Convolutional Neural Network Approaches and the U-Net 3D Model

Deep learning, especially through convolutional neural networks (CNN) such as the U-Net 3D model, has revolutionized fault identification from seismic data, representing a significant leap over traditional methods. Our review traces the evolution of CNN, emphasizing the adaptation and capabilities of the U-Net 3D model in automating seismic fault delineation with unprecedented accuracy. We find: 1) The transition from basic neural networks to sophisticated CNN has enabled remarkable advancements in image recognition, which are directly applicable to analyzing seismic data. The U-Net 3D model, with its innovative architecture, exemplifies this progress by providing a method for detailed and accurate fault detection with reduced manual interpretation bias. 2) The U-Net 3D model has demonstrated its superiority over traditional fault identification methods in several key areas: it has enhanced interpretation accuracy, increased operational efficiency, and reduced the subjectivity of manual methods. 3) Despite these achievements, challenges such as the need for effective data preprocessing, acquisition of high-quality annotated datasets, and achieving model generalization across different geological conditions remain. Future research should therefore focus on developing more complex network architectures and innovative training strategies to refine fault identification performance further. Our findings confirm the transformative potential of deep learning, particularly CNN like the U-Net 3D model, in geosciences, advocating for its broader integration to revolutionize geological exploration and seismic analysis.

Field Test Summary of Two Kinds of Electronic Detonator for Seismic Exploration

Electronic detonators are widely used because of their advantages in real-time supervision of the whole life cycle (Zang, 2022). Due to the high requirements of the time difference synchronization between the electronic initiation system and the seismic wave recording system, the Electronic detonator has not been widely used for Seismic exploration (Yang, 2020). This paper expounds the systematic and scientific test method from the aspects of the comprehensive performance of electronic detonators for exploration, the compatibility between the electronic detonator initiation system and the geophysical blasting machine system, the constraints of the geophysical explosion-related collaborative Danling managment cloud platform, and the quality of data collected by electronic detonator blasting in wells., and based on the analysis of the test results, the problems that need to be improved in the application of electronic detonators and detonation systems in the large-scale production of geophysical prospecting industry are put forward. .

Application Results of 3-D Seismic Exploration Technology in Coal Mines

This paper briefly introduces the development and present situation of China's coal seismic exploration. It focuses on analyzing the important functions of 3-D seismic exploration technology in the designing and production of coal mines, and also the results of its application.

China Seismic Experimental Site(CSES): Challenges of Deep Earth Exploration and Practice(DEEP)

Since May 2018,the planning,construction and functioning of China Seismic Experimental Site(CSES)has attracted much attention in earthquake science(CSES,2020 a,b,c;Wu,2020;Li et al.,2021).Different from traditional earthquake prediction experiment projects,such as the Parkfield earthquake prediction experiment(Roeloffs,2000).

Preface to the Special Issue on Advances in Seismic Exploration and Monitoring with Active Sources in China

Analyzing the information carriede by seismic waves is a major means for human beings to have an insight into the structure of the earth’s interior,and by using artificial seismic sources to excite seismic waves,we can obtain high-resolution images for the crustal and smaller scale medium.Artificial seismic exploration methods have been widely applied to fields such as

Seismic fine imaging and its significance for natural gas hydrate exploration in the Shenhu Test Area, South China Sea

Shenhu area in South China Sea includes extensive collapse and diapir structures,forming high-angle faults and vertical fracture system,which functions as a fluid migration channel for gas hydrate formation.In order to improve the imaging precision of natural gas hydrate in this area,especially for fault and fracture structures,the present work propose a velocity stitching technique that accelerates effectively the convergence of the shallow seafloor,indicating seafloor horizon interpretation and the initial interval velocity for model building.In the depth domain,pre-stack depth migration and residual curvature are built into the model based on high-precision grid-tomography velocity inversion,after several rounds of tomographic iterations,as the residual velocity field converges gradually.Test results of the Shenhu area show that the imaging precision of the fault zone is obviously improved,the fracture structures appear more clearly,the wave group characteristics significantly change for the better and the signal-to-noise ratio and resolution are improved.These improvements provide the necessary basis for the new reservoir model and field drilling risk tips,help optimize the favorable drilling target,and are crucial for the natural gas resource potential evaluation.

Active Fault Exploration and Seismic Hazard Assessment in Fuzhou City

It has been proven by a number of earthquake case studies that an active fault-induced earthquake beneath a city can be devastating. It is an urgent issue for seismic hazard reduction to explore the distribution of active faults beneath the urban area and identify the seismic source and the risks underneath. As a pilot project of active fault exploration in China, the project, entitled “Active fault exploration and seismic hazard assessment in Fuzhou City", started in early 2001 and passed the check before acceptance of China Earthquake Administration in August 2004. The project was aimed to solve a series of scientific issues such as fault location, dating, movement nature, deep settings, seismic risk and hazard, preparedness of earthquake prevention and disaster reduction, and etc. by means of exploration and assessment of active faults by stages, i.e., the preliminary survey and identification of active faults in target area, the exploration of deep seismotectonic settings, the risk evaluation of active seismogenic faults, the construction of geographic information system of active faults, and so on. A lot of exploration methods were employed in the project such as the detection of absorbed mercury, free mercury and radon in soil, the geological radar, multi-channel DC electrical method, tsansient electromagnetic method, shallow seismic refraction and reflection, effect contrast of explored sources, and various sounding experiments, to establish the buried Quaternary standard section of the Fuzhou basin. By summing up, the above explorations and experiments have achieved the following results and conclusions: (1)The results of the synthetic pilot project of active fault exploration in Fuzhou City demonstrate that, on the basis of sufficient collection, sorting out and analysis of geological, geophysical and borehole data, the best method for active fault exploration (location) and seismic risk assessment (dating and characterizing) in urban area is the combination of various approaches, that is, the possible location of active fault determined by using geochemical exploration as a guide “scout", the shallow seismic sounding as the main tool, the electromagnetic method as a supplement, establishing the standard Quaternary profile or stratigraphic sequence from drilling and various geophysical parameters from borehole logs as methods to correct and verify the data above. And in addition, the method also includes the field surveys on fault exposures, trenching, paleoearthquake investigation, dating and comparison of lithology, strata sequence, absolute or relative ages of the cores on the two sides of buried faults. (2)The Fuzhou basin locates under the regional seismotectonic settings which have the potential of moderate earthquake. Comparatively, the region is less affected by the “Taiwan dynamic Antenna"; (3)The activity of the major faults in Fuzhou basin is weak in general. All the six identified target faults are not Holocene faults, among which the Bayi Reservoir-Shanggan fault and the Minhou-Nanyu fault are dormant at least since the mid Epipleistocene time, and the rest are dormant since the Epipleistocene time; (4)In terms of deep-seated structures beneath the basin, there is no evidence indicating the possible occurrence of the underneath strong destructive earthquakes. The adjacent Changle-Zhao’an fault zone is the potential seismic source which may possibly affect Fuzhou City; (5)There exists potential of moderate-strong earthquake on the major faults of the region, but the probability is low; (6)The seismic hazards are weak in the region and the surface earthquake fractures are not likely to occur; (7)The first geographic information system of active faults is developed with functions of information query and display, data management, analysis and processing, etc.

Method of high-density seismic imaging exploration and application samples

The paper introduces the method of high-density seismic imaging exploration, discusses its features different from conventional shallow seismic reflection wave technique, and illustrates the application effect of the method using three samples of engineering geological explorations on land and in water exploration of underground cavity, location survey of sunk ship and investigation of channel silt depth.

Full wave seismic exploration technology

Reflected wave seismology has the following defects:the acquisition design is based on the assumption of layered media,the signal processing suppresses weak signals such as diffracted wave and scattered wave,and the seismic wave band after the image processing is narrow.They limit the full utilization of broadband raw data.The concept of full wave seismic exploration is redefined based on the idea of balanced utilization of reflected wave,diffracted wave and scattered wave information,its characteristics and adaptive conditions are clarified.A set of key technologies suitable for full wave seismic exploration are put forward.During seismic acquisition period,it is necessary to adopt multi geometry,i.e.embed small bin,small offset and small channel interval data in conventional geometry.By discretizing of common midpoint(CMP)gathers,small offset with high coverage,the weak signals such as diffracted wave and scattered wave in the raw seismic data can be enhanced.During seismic processing,the signal and noise in the original seismic data need to be redefined at first.The effective signals of seismic data are enhanced through merging of multi-geometry data.By means of differential application of data with different bin sizes and different arrangement modes,different regimes of seismic waves can be effectively decomposed and imaged separately.During seismic interpretation stage,making the most of the full wave seismic data,and adopting well-seismic calibration on multi-scale and multi-dimension,the seismic attributes in multi-regimes and multi-domains are interpreted to reveal interior information of complex lithology bodies and improve the lateral resolution of non-layered reservoirs.

New Progress in High-Precision and High-Resolution Seismic Exploration Technique in Coal Industry of China

In the past twenty years, the proportion of coal in primary-energy consumption in China is generally between 71.3% and 76.5%. The output of coal was 1.374 billion tons in 1996, and 1.21 tons in 1998, which ranked first in the world. Now coal is mined mainly with mechanization in China, which is planned to reach 80% in major State-owned coal mines in 2000 according to the planning of the government (Li et al., 1998; Tang Dejin, 1998).

Applying Non-Local Means Filter on Seismic Exploration

The seismic reflection method is one of the most important methods in geophysical exploration.There are three stages in a seismic exploration survey:acquisition,processing,and interpretation.This paper focuses on a pre-processing tool,the Non-Local Means(NLM)filter algorithm,which is a powerful technique that can significantly suppress noise in seismic data.However,the domain of the NLM algorithm is the whole dataset and 3D seismic data being very large,often exceeding one terabyte(TB),it is impossible to store all the data in Random Access Memory(RAM).Furthermore,the NLM filter would require a considerably long runtime.These factors make a straightforward implementation of the NLM algorithm on real geophysical exploration data infeasible.This paper redesigned and implemented the NLM filter algorithm to fit the challenges of seismic exploration.The optimized implementation of the NLM filter is capable of processing production-size seismic data on modern clusters and is 87 times faster than the straightforward implementation of NLM.

Indexes of CNPC Seismic Exploration in 1995

ＩｎｄｅｘｅｓｏｆＣＮＰＣＳｅｉｓｍｉｃＥｘｐｌｏｒａｔｉｏｎｉｎ１９９５Ｉｎ１９９５，ＣＮＰＣＧｅｏｐｈｙｓｉｃａｌＥｘｐｌｏｒａｔｉｏｎＢｕｒｅａｕｃｏｍｐｌｅｔｅｄ２９５２０ｋｉｌｏｍｅｔｅｒｓｏｆ２－Ｄｓｅｉｓｍｉｃｓｕｒｖｅｙａｎｄ１６９３...

Deep Seismic Exploration in the Taiwan Straits: The HX9 Survey Line Experiment and Preliminary Results

By using an offshore large volume air-gun seismic source, onshore seismic stations( including mobile stations and permanent stations) and ocean bottom seismometers,a deep seismic exploration experiment was carried out for the first time in the Taiwan Straits. Results show that seismic stations can receive seismic signals from the air-gun arrays of the "YANPING Ⅱ"scientific investigation ship from as far as 280 km away.Tens of thousands of high quality seismic data items were obtained successfully and different types of P-wave seismic phases were identified. A one-dimensional crustal structure model of the survey profile HX9 shows that the crustal structure,which is reflected by Pc and Pm P reflection waves from two velocity discontinuities and basement refraction wave( Pg) constitutes the basic characteristic of the crustal structure in this region. The depths of Conrad discontinuity and Moho discontinuity are respectively16. 0km- 17. 5km and 28. 0km- 29. 5km.

Application of High-Density Seismic Image in Nondestructive Exploration of Cut-off Cement-Soil Wall in Earth Dam

In order to quickly explore the quality of cut-off wall in dams, a new method of high-density seismic image was adopted and estimated by model and in-situ wall tests.The vibration exciter was employed and several parameters such as hypocentral distance, length of signal record and sampling space in signal collection were determined, which are 8 m, 0.25 ms and 128 ms respectively. Through time and frequency field signal analyses, it is concluded that, the smaller arrival times of reflected longitudinal and surface waves, and the higher their main frequencies, the higher the strength of the wall, vice versa. Accordingly the construction quality of the wall can be evaluated quickly by high-density seismic image.

Characteristics of the Zhengzhou Laoyachen Fault Revealed by Seismic Exploration Data

Exploration and research of fault activities are the fundamentals of earthquake prediction and prevention and disaster reduction. In order to determine the location, characteristics and activities of the Zhengzhou-Laoyachen fault, shallow seismic prospecting with different exploration depth across the Laoyachen fault was carried out in the northern suburbs of Zhengzhou city in 2006. The images of the subterranean structure and tectonics at depths of 30m～6000m have been available by applying the combined methods of explosive seismic sources and vibrator seismic sources, as well as the combination of diverse observation systems with different parameters. The outcome indicates that the Laoyachen fault is a normal fault running NW and dipping NE, which offsets stratums ahead of Neogene (N). However, no fault displacements are found in the interior stratums of Q+N.

Study on Anti-Disturbance and High-Resolution Shallow Seismic Exploration of Active Faults in Urban Regions

The significance of detection of urban active faults and the general situation concerning detection of urban active faults in the world are briefly introduced. In a brief description of the basic principles of anti-disturbance and high-resolution shallow seismic exploration, the stress is put on the excitation of seismic sources, the performance of digital seismographs, receiving mode and conditions, geometry as well as data acquisition, processing and interpretation in the anti-disturbance and high-resolution shallow seismic exploration of urban active faults. The study indicates that a controlled seismic source with a linear or nonlinear frequency-conversion scanning function and the relevant seismographs must be used in data acquisition, as well as working methods for small group interval, small offset, multi-channel receiving, short-array and high-frequency detectors for receiving are used. Attention should be paid to the application of techniques for static correction of refraction, noise suppressing, high-precision analysis of velocity, wavelet compressing, zero-phasing of wavelet and pre-stacking migration to data processing and interpretation. Finally, some cases of anti-disturbance and high-resolution shallow seismic exploration of urban active faults are present in the paper.

Exploration of Laoyachen fault in Zheng-zhou and its activity investigation

In the paper, an exploration is made by the techniques of shallow seismic prospecting, borehole composite profile analysis, field morphological investigation, and new geological dating for the Laoyachen fault in Zhengzhou that was originally recognized as an active one. The result from shallow seismic prospecting indicates this fault only existed in the stratum prior to the Neogene, dislocations and activity traces of this fault could not be found in the Neogene stratum. At the same time, the surface morphological investigation reveals that the location of the so-called "fault scarp" is not consistent with that of Laoyachen fault. Moreover, seismic drilling and borehole composite profile analysis also indicate that the scarp only developed in Malan Loess. The stratum beneath it is gentle and no dislocation traces can be seen. Therefore, we propose that this scarp is not relevant to the Laoyachen fault, which might be resulted from the diverted course of Yellow River. Laoyachen fault is not an active one.

Complex Exploration Techniques for the Low-permeability Lithologic Gas Pool in the Upper Paleozoic of Ordos Basin

The Ordos basin is a stable craton whose late Paleozoic undergoes two sedimentary stages: from the middle- late Carboniferous offshore plain to the Permian continental river and lake delta. Sandstones in delta plain channels, delta-front river mouth bars and tidal channels are well developed. The sandstones are distributed on or between the genetic source rocks, forming good gas source conditions with widespread subtle lithologic gas pools of low porosity, low permeability, low pressure and low abundance. In recent years, a series of experiments has been done, aimed at overcoming difficulties in the exploration of lithologic gas pools. A set of exploration techniques, focusing on geological appraisal, seismic exploration, accurate logging evaluation and interpretation, well testing fracturing, has been developed to guide the exploration into the upper Paleozoic in the basin, leading to the discoveries of four large gas fields: Sulige, Yulin, Wushenqi and Mizhi.