In-situ polymerized PEO-based solid electrolytes contribute better Li metal batteries:Challenges,strategies,and perspectives

Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)with good electrochemical stability and excellent Li salt solubility are considered as one of the most promising SPEs for solid-state lithium metal batteries(SSLMBs).However,PEO-based SPEs suffer from low ionic conductivity at room temperature and high interfacial resistance with the electrodes due to poor interfacial contact,seriously hindering their practical applications.As an emerging technology,in-situ polymerization process has been widely used in PEO-based SPEs because it can effectively increase Li-ion transport at the interface and improve the interfacial contact between the electrolyte and electrodes.Herein,we review recent advances in design and fabrication of in-situ polymerized PEO-based SPEs to realize enhanced performance in LMBs.The merits and current challenges of various SPEs,as well as their stabilizing strategies are presented.Furthermore,various in-situ polymerization methods(such as free radical polymerization,cationic polymerization,anionic polymerization)for the preparation of PEO-based SPEs are summarized.In addition,the application of in-situ polymerization technology in PEO-based SPEs for adjustment of the functional units and addition of different functional filler materials was systematically discussed to explore the design concepts,methods and working mechanisms.Finally,the challenges and future prospects of in-situ polymerized PEO-based SPEs for SSLMBs are also proposed.

Enhanced thermal and electrical properties of poly (D,L-lactide)/ multi-walled carbon nanotubes composites by in-situ polymerization

Biodegradable poly （D,L-lactide） （PLA）/carboxyl-functionalized multi-walled carbon nanotubes （c-MWCNTs） composites were achieved via in-situ polymerization. These as-prepared composite materials were characterized with FT-IR, XRD, TG, DSC, SEM, and high insulation resistance meter. The results demonstrate that the multi-walled carbon nanotube was carboxyl functionalized, which improved the collection between c-MWCNTs and PLA, and further realized the graft copolymerization of c-MWCNTs and PLA. There is a higher glass transition temperature and a lower pyrolysis temperature of PLA/c-MWCNTs composites than pure PLA. The c-MWCNTs gave a better dispersion than unmodified MWCNTs in the PLA matrix, and an even coating of PLA on the surface of c-MWCNTs was obtained, which increased the interfacial interaction. High insulation resistance analysis showed that the addition of c-MWCNTs increased the electric conductivity, and c-MWCNTs performed against the large dielectric coefficient and electrostatic state of PLA. These results demonstrated that c-MWCNTs modified PLA composites were beneficial for potential application in the development of heat-resisting and conductivity plastic engineering.

In-situ interfacial passivation and self-adaptability synergistically stabilizing all-solid-state lithium metal batteries

The function of solid electrolytes and the composition of solid electrolyte interphase(SEI)are highly significant for inhibiting the growth of Li dendrites.Herein,we report an in-situ interfacial passivation combined with self-adaptability strategy to reinforce Li_(0.33)La_(0.557)TiO_(3)(LLTO)-based solid-state batteries.Specifically,a functional SEI enriched with LiF/Li_(3)PO_(4) is formed by in-situ electrochemical conversion,which is greatly beneficial to improving interface compatibility and enhancing ion transport.While the polarized dielectric BaTiO_(3)-polyamic acid(BTO-PAA,BP)film greatly improves the Li-ion transport kinetics and homogenizes the Li deposition.As expected,the resulting electrolyte offers considerable ionic conductivity at room temperature(4.3 x 10~(-4)S cm^(-1))and appreciable electrochemical decomposition voltage(5.23 V)after electrochemical passivation.For Li-LiFePO_(4) batteries,it shows a high specific capacity of 153 mA h g^(-1)at 0.2C after 100 cycles and a long-term durability of 115 mA h g^(-1)at 1.0 C after 800 cycles.Additionally,a stable Li plating/stripping can be achieved for more than 900 h at 0.5 mA cm^(-2).The stabilization mechanisms are elucidated by ex-situ XRD,ex-situ XPS,and ex-situ FTIR techniques,and the corresponding results reveal that the interfacial passivation combined with polarization effect is an effective strategy for improving the electrochemical performance.The present study provides a deeper insight into the dynamic adjustment of electrode-electrolyte interfacial for solid-state lithium batteries.

Heat Transfer Characteristics of Dropwise Condensation of Steam on Vertical Polymer Coated Plates

The plasma polymerization method and dynamic ion-beam mixed implantation method were employed to coat ultra-thin polymer films on copper plates. Experiments indicated that steady dropwise condensation of steam at atmospheric pressure occurred. The condensation heat transfer coefficients increased by approximately 3 and 5－7 times for the polytrimethylvinylsilane film and polytetrafluoroethylene film respectively, compared with the value for film condensation under the same experimental conditions. The temperatures on the condensing surface and inside the test block were found to be rapidly and randomly fluctuated. The properties of the coated films and advantages of the methods used in this investigation were discussed briefly.

STUDY ON THE CARDANOL-ALDEHYDE CONDENSATION POLYMER CONTAINING BORON-NITROGEN COORDINATE BOND

Cardanol-aldehyde condensation polymer containing boron-nitrogen coordinate bond (CFBN) has been synthesized and characterized by IR, XPS, HPLC and DTA-TG. Its properties were also investigated. The results show that the coating film of CFBN has excellent physico-mechanical properties, good anticorrosive properties and stable at high temperature. (Author abstract) 8 Refs.

Syntheses,crystal structures,and catalytic properties of three zinc(Ⅱ),cobalt(Ⅱ)and nickel(Ⅱ)coordination polymers constructed from 5⁃(4⁃carboxyphenoxy)nicotinic acid

Three zinc(Ⅱ),cobalt(Ⅱ),and nickel(Ⅱ)coordination polymers,namely[Zn(μ^(3-)cpna)(μ-dpea)_(0.5)]_(n)(1),[Co(μ^(3-)cpna)(μ-dpey)_(0.5)]_(n)(2),and[Ni(μ^(3-)cpna)(μ-dpey)_(0.5)(H_(2)O)]_(n)(3),have been constructed hydrothermally using H_(2)cpna(5-(4-carboxyphenoxy)nicotinic acid),dpea(1,2-di(4-pyridyl)ethane),dpey(1,2-di(4-pyridyl)ethylene),and zinc,cobalt,and nickel chlorides at 160℃.The products were isolated as stable crystalline solids and were characterized by IR spectra,elemental analyses,thermogravimetric analyses,and single-crystal X-ray diffraction analyses.Single-crystal X-ray diffraction analyses revealed that three compounds crystallize in the triclinic system,space group P1.Compounds 1-3 show 2D layer structures.The catalytic activities in the Knoevenagel condensation reaction of these compounds were investigated.Compounds 1 and 2 exhibit effective catalytic activities in the Knoevenagel condensa-tion reaction at room temperature.For this reaction,various parameters were optimized,followed by the investiga-tion of the substrate scope.CCDC:2335676,1;2335677,2;2335678,3.

SYNTHESIS AND CHARACTERIZATION OF POLYPROPYLENE/MONTMORILLONITE NANOCOMPOSITES VIA AN in-situ POLYMERIZATION APPROACH

Polypropylene/montmorillonite (PP/MMT)nanocomposites were prepared by in-situ polymerization using aMMT/MgCl_2/TiCl_4-EB Ziegler-Natta catalyst activated by triethylaluminum(TEA). The enlarged layer spacing of MMT wasconfirmed by X-ray wide angle diffraction (WAXD), demonstrating that MMT were intercalated by the catalyst components.X-ray photoelectron spectrometry (XPS) analysis proved that TiCl_4 was mainly supported on MgCl_2 instead of on the surfaceof MMT The exfoliated structure of MMT layers in the PP matrix of PP/MMT composites was demonstrated by WAXDpatterns and transmission electron microscopy (TEM) observation. The higher glass transition temperature and higher storage modulus of the PP/MMT composites in comparison with pure PP were revealed by dynamic mechanical analysis (DMA).

Preparation of Polysulfonamide/ZnO Nanocomposite by In-Situ Polymerization

Polysulfonamide/zinc oxide(PSA/ZnO) nanocomposite films with w(ZnO)=0.5% were prepared by in-situ polymerization based on 4,4′-diaminodiphenylsulfone and terephthaloyl chloride in the common solvent N,N-Dimethylacetamide(DMAc). Atomic force microscopy (AFM) was employed to observe the microstructure of the composite film. The thermal property was investigated by TGA and mechanical property was characterized by DXLL-1000 electromechanical material testing machine. The results showed that the breaking strength of the film containing 0.5% ZnO was great enhanced. The average size of ZnO particles was below 100 nm. The introduction of ZnO as nano filler in PSA react as UV shield effect and make the composite mechanical property improved.

CHANGES OF STRUCTURE AND PROPERTIES OF POLY (ETHYLENE TEREPHTHALATE) CAUSED BY IN-SITU POLYMERIZATION OF PYRROLE

Conductive polymer composites based on crystalline polymer matrix have been prepared by using an in-situ polymerization process of pyrrole in amorphous poly （ethylene terephthalate） （PET） film. The DSC and WAXD measurement and SEM observation show that liquid-induced crystallization of PET matrix has occurred during the preparation of composite films. Depending upon the equilibrium degree of swelling and crystallinity, the limited depth of penetration of pyrrole molecules results in a skin-core structure of the composite film. The skin layer containing charge transfer intercalated polypyrrole has a surface resistance of 3.5×10;Ω. Rigid and heat-resistant polypyrrole molecules formed in PET film increase the tensile modulus and, especially, the rigidity of PET at elevated temperatures. However, they decrease the tensile strength and elongation at break, and impair the thermal ductility of PET.

Studies on the Self-condensing Vinyl Living Radical Polymerization of a Novel Acrylate Inimer

A novel acrylate inimer, 2-（2-chloroacetyloxy） ethyl acrylate, was prepared by the reaction of 2-hydroxyethyl acrylate with chloroacetyl chloride in the presence of triethylamine. The self-condensing vinyl living radical polymerization of the inimer was studied and the hyperbranched macromolecules containing ester linkages on their backbone were prepared. All the polymerization products were characterized by 1H NMR. The polymerization degree and the branching parameter were calculated based on the 1H NMR spectra. It has been shown that this inimer exhibits a very distinctive polymerization behavior. Similar to step-growth polymerization, the polymerization degree of the products formed increased exponentially during the early stage of the polymerization, and then the increasing rate slowed down. However, the inimer remained present throughout the polymerization consistent with conventional free radical polymerization. Also, if much longer polymerization time was used, the polymerization system would become gel due to the crosslinking reaction derived from radical-radical recombination. As a result of the unequal reactivity of -CH2Cl and >CHCl, an almost linear product was obtained at a molar ratio of bipy to inimer=0.05, while a relatively high ratio of bipy to inimer 1 favored the formation of the branched structure. The macromolecules formed at a high ratio of bipy to inimer 1 exhibited an excellent solubility in organic solvents such as acetone.

Studies on the Self-condensing Vinyl Polymerization of a Novel Maleimide Inimer

The self-condensing vinyl polymerization(SCVP) of a novel maleimide inimer(initiator-monomer) 1, N-(4-α-bromobutyryloxy phenyl) maleimide with the complex of CuBr/Bipy(2, 2′-bipyridine) as the catalyst was studied. GPC was used to determine the molecular weight and the results show that the molecular weight increases exponentially with polymerization time during the first hour, and then the rate of increase molecular weight slows down. The molecular weight also increases with increasing dosage of the catalyst. The coincidence of the molecular weights determined by 1H NMR and GPC proves that the polymer obtained from the SCVP of inimer 1 has a linear structure, which is further verified by 13C NMR spectrum. A hyperbranched polymer was obtained by the copolymerization of inimer 1 and styrene.

Synthesis of Highly Branched Poly(ε-caprolactone) by Self-condensing Atom Transfer Radical Polymerization of Macroinimers

Branched poly（ε-capmlactone） was synthesized by self-condensing atom transfer radical polymerization of macroinimer, α-acryloyoxy-ω-2-bromopropionyloxy poly（ε-caprolactone）, which was prepared by enzyme-catalyzed ring-opening polymerization of ε-caprolactone with 2-hydroxylethyl acrylate as initiator and esterification of the ω-hydroxyl group of the obtained poly（ε-caprolactone） by 2-bromopropionyl bromide.

PREPARATION OF POLYSULFONAMIDE AND MODIFIED TITANIUM OXIDE NANOCOMPOSITES BY IN-SITU POLYMERIZATION

A kind of new nano composite with ultraviolet （UV） ray resistance and high temperature stability was prepared by in-situ polymerization in low temperature. Polysulfonamide （PSA） was synthesized with 4, 4＇-diaminodiphenyl sulfone （DDS） and terephthaloyl chloride （TPC） in the common solvent N, N-Dimethyl- -acetamide （DMAc）. Nano filler is a certain nano titanium oxide modified by silicon oxide （TMS）, which plays the role of UV resistance additives. Properties of the novel composite materials were characterized by Atomic Force microscopy （AFM）, thermal gravimetric Analysis （TGA） and Ultraviolet Spectroscopy. AFM had showed the sizes and distributions of TMS particles in the nanocomposite. Ultraviolet Spectroscopy for the nanocomposites showed a large absorption in UV band. TGA showed the decomposition temperature was increased over ten degrees with 0.5% wt TMS for this nanocomposite compared with pure PSA.

Filmwise Condensation Heat Transfer Enhancement with Dropwise and Filmwise Coexisting Condensation Surfaces

Six surfaces were prepared with defferent surface division patterns for the experimental investigationof steam condensation heat transfer characteristics for dropwise and filmwise coexisting(DFC)condensationsurfaces under atmospheric pressure Dropwise condensation(DWC)was promoted with an ultrathin polytetrafluoroethylene(PTFE)film,which was prepared by the dynamic ion-beam mixed implantation(DIMI)method.The results showed that the condensation phenomena at the intersection between the dropwise andfilmwise condensation regios were quite different for different relative positions of the dropwise and filmwisecondensation regions.The experimental results revealed that the condensation heat transfer characteristics werehighly influenced by the surface division number and the relative area ratio of the dropwise and filmwise conden-sation regions.The impact of thesc findings on heat transfer enhancement mechanism for condensation heattransfer is discussed in detail.

Morphology and conductivity of in-situ PEO-LiClO_4-TiO_2 composite polymer electrolyte

PEO-LiClO4-TiO2 composite polymer electrolyte films were prepared. TiO2 was formed directly in matrix by hydrolysis and condensation reaction of tetrabutyl titanate. The crystallinity, morphology and ionic conductivity of composite polymer electrolyte films were examined by differential scanning calorimetry, scanning electron microscopy, atom force microscopy and alternating current impedance spectroscopy, respectively. The glass transition temperature and the crystallinity of composite polymer electrolytes are decreased compared with those of PEO-LiClO4 polymer electrolyte film. The results show that TiO2 particles are uniformly dispersed in PEO-LiClO4-5%TiO2 composite polymer electrolyte film. The maximal conductivity of 5.5×10、5 Scm at 20 ℃ of PEO-LiClO4-TiO2 film is obtained at 5% mass fraction of TiO2.

Crystalline Morphology and Crystallization Characteristics of In-situ Blends of Anionic Polyamide 6 with Noncrystallizable Semiaromatic Polyamide Copolymer

A noncrystallizable semiaromatic polyamide copolymer（NSAP） was dissolved in molten caprolactam, and PA6/ NSAP blends were produced in-situ via the anionic ring-opening polymerization of caprolactam. The presence of a single loss tangent（tanS） peak measured by means of dynamic mechanical analysis（DMA） proves the miscibility between PA6 and NSAP in the blends. It was found that there existed drastic changes in the crystallographic form and crystallization kinetics for the in-situ blends, e.g. , when 20% NSAP was added, nearly all crystallites existed in the ,y form and the crystallization could hardly occur upon cooling even at a rate of 2.5 ℃/min. Moreover, cold crystallization appears during the subsequent heating, and its melting point is 40 ℃ lower than that of the virgin system. On the other hand, the size of the spherulites only decreases modestly. It is suggested that the introduction of irregular stiff segments originated from NSAP into PA6 macromolecule chain, which resulted from transamidation during the polymerization play a dominant role in the drastic change of crystallization kinetics and the resultant morphology of the in-situ blends.

Manipulating the antioxidative capacity of melanin-like nanoparticles by involving condensation polymerization

Melanin is ubiquitous in nature and plays important roles in physiological activities especially in keeping the oxidative balance.Both natural and synthetic melanin were synthesized via the free radical polymerization of 5,6-dihydroxyindole(DHI)monomer,which may lead to the inherent compactπ-conjugation stacking microstructures and finally results in limited antioxidative capacities.To address this issue,we have strived to involve condensation polymerization during the melanin synthetic process,aiming to disrupt the compact stacking microstructures and improve the total antioxidative performance.The resulting melaninlike nanoparticles(NPs)indeed possessed less compact stackingπ-conjugation structures and decreased density,which further demonstrated enhanced antioxidative abilities compared with conventional melanin-like polymers such as poly-5,6-dihydroxyindole(Poly-DHI)and polydopamine(PDA).Their excellent free radical scavenging capability was further confirmed by the intracellular cell protection effects against reactive oxygen species(ROS)as well as in vivo therapy for acute diseases including acute kidney injury and acute liver injury.This work would promote future work toward new types of melanin-inspired nanomaterials with tunable and improved functions beyond nature.

Visualization of adaptive polymer flow and displacement in medium-permeable 3D core-on-a-chip

Polymer flooding has been witnessed an effective technology for enhancing oil recovery from medium-to low-permeability reservoirs;however, direct visualization of polymer solution flow in such reservoir condition is still lacking. In this work, a three-dimensional (3D) core-on-a-chip device with a permeability of around 200 mD was prepared and employed to visualize the pore-scale flow and displacement of a self-adaptive polymer (SAP, 8.7 × 106 g·mol−1)−whose microscopic association structure and macroscopic viscosity can reversibly change in response to shear action−versus partially hydrolyzed polyacrylamide (HPAM), by recording their flow curves, monitoring dynamic transportation process via particle imaging velocimetry, and building 3D structure of remaining oil. The results show that, in single-phase flow, all polymer solutions exhibit flow thinning and then thickening regions as flow rate increases, but the transition between two regimes occurs at a small Weissenberg number (10−3−10−1) in this medium-permeable condition. In contrast to HPAM-1 with close weight-average molecular weight (Mw), the adaptive character not only extends SAP's shear-govern region, allowing SAP to propagate piece by piece and achieve higher accessible pore volume, but it also enhances the elastic resistibility of polymer in the extension-dominated regime, increasing the microscopic displacement efficiency. These two effects result in 1.5–3 times more oil recovery factor for SAP than for HPAM-1. Regarding ultra-high-Mw HPAM-2 (25 × 106 g·mol−1), plugging and chain degradation do occur, thus producing lower oil recovery than SAP. This work provides a direct approach for in-situ assessment of polymer-based displacing system under a more authentic condition of practical reservoirs.

SYNTHESIS OF SPHERICAL MACROPOROUS ADSORBENT BASED ON UREA-FORMALDEHYDE CONDENSED POLYMER

Spherical macroporous adsorbents with active sites capable of hydrogen bonding adsorption based on urea-formaldehyde condensed polymer were synthesized via reversed suspension polymerization. The properties of the obtained adsorbent were also investigated in detail. The results showed that the water permeability could be improved by adding hydroxyl-containing organic compound moiety into the adsorbent. The specific surface area and average pore diameter of these adsorbents increased while the porosity first increased then decreased with the increase of the amount of the added hydroxyl-containing compound.

A NOVEL EOR POLYMER (Ⅱ)——INVESTIGATION ON IN-SITU GELATION OF SMRF SYSTEM IN BEREA CORE

In-situ gelation of aqueous sulfomethylated resorcinol formaldehyde (SMRF) system inBerea core has been investigated. Two sets of displacement experiments were conducted with thissystem (containing 5% NaCl, 0. 036% CaCl_2. 2H_2O). The brine permeabilities of the coreswere reduced significantly from about 600 to 0.1 md. The in-situ gelation in Berea core occurreda little bit earlier than gelation anticipated from bulk test in the experiments. The gel time waseasier to control at initial pH between 6 and 8. During injection of SMRF system, the apparentviscosity was less than 1 mPa·s at 41℃.