Methanol oxidation reaction （MOR） at Pt and Pt electrode surface deposited with various amounts of Ru （denoted as PtxRuy, nominal coverage y is 0.17, 0.27, and 0.44 ML） in 0.1 mol/L HClO4＋0.5 mol/L MeOH has been ...Methanol oxidation reaction （MOR） at Pt and Pt electrode surface deposited with various amounts of Ru （denoted as PtxRuy, nominal coverage y is 0.17, 0.27, and 0.44 ML） in 0.1 mol/L HClO4＋0.5 mol/L MeOH has been studied under potentiostatic conditions by in situ FTIR spectroscopy in attenuated-total-reflection con guration and di erential electro-chemical mass spectrometry under controlled flow conditions. Results reveal that （i） CO is the only methanol-related adsorbate observed by IR spectroscopy at all the Pt and PtRu electrodes examined at potentials from 0.3 V to 0.6 V （vs. RHE）; （ii） at Pt0.56Ru0.44, two IR bands, one from CO adsorbed at Ru islands and the other from COL at Pt substrate are detected, while at other electrodes, only a single band for COL adsorbed at Pt is observed; （iii） MOR activity decreases in the order of Pt0.73Ru0.27〉Pt0.56Ru0.44〉Pt0.83Ru0.17〉Pt; （iv） at 0.5 V, MOR at Pt0.73Ru0.27 reaches a current e ciency of 50% for CO2 production, the turn-over frequency from CH3OH to CO2 is ca. 0.1 molecule/（site sec）. Suggestions for further improving of PtRu catalysts for MOR are provided.展开更多
Infrared(IR)absorption spectroscopy has been widely used for dynamic characterization of catalysts and mechanism of catalytic reactions.However,due to the strong infrared absorption of heterogeneous catalysts(mainly o...Infrared(IR)absorption spectroscopy has been widely used for dynamic characterization of catalysts and mechanism of catalytic reactions.However,due to the strong infrared absorption of heterogeneous catalysts(mainly oxides,or supported metal and metal oxides,etc.)below 1200 cm^(-1),and the intensity of regular infrared light source rapidly decays at low-wavenumber range,most in-situ infrared spectroscopy studies are limited to the detection of surface adsorbates in the range of 4000-900 cm^(-1).The change of catalytically active component itself(M-O,M-M bond,etc.,1200-50 cm^(-1))during the reaction is hard to be tracked under reaction conditions by in-situ IR.In this work,a home-made in-situ IR reactor was designed and a sample preparing method was developed.With such progresses,the changes of reactants,products,surface adsorbates,and catalysts themselves can be measured under the same reaction conditions with a spectral range of 4000-400 cm^(-1),providing a new opportunity for in-situ characterization of heterogeneous catalysis.CO oxidation on Pd/SiO_(2) and Cu/SiO_(2) catalysts were taken as examples,since both the two catalytic systems were extensively used commercially,and moreover reduction and oxidation of palladium and copper occur during the examined reaction conditions.The characteristic bands of Pd^(2+)-O(670,608 cm^(-1)),Cu^(+)-O(635 cm^(-1))and Cu^(2+)-O(595,535 cm^(-1))were observed by IR,and the changes during CO oxidation reaction were successfully monitored by IR.The oxidation/reduction of palladium and copper were also confirmed by ex-situ XPS.Moreover,Pd^(0) in Pd/SiO_(2) and Cu^(+)in Cu/SiO_(2) were found as the thermal dynamically stable phases under the examined conditions for CO oxidation.展开更多
Polyelectrolyte becomes more and more popular in electrocatalysis.The understanding of electrode/polyelectrolyte interfaces at the molecular level is important for guiding further the polyelectrolyte-based electrocata...Polyelectrolyte becomes more and more popular in electrocatalysis.The understanding of electrode/polyelectrolyte interfaces at the molecular level is important for guiding further the polyelectrolyte-based electrocatalysis.Herein,we demonstrate an in-situ surface-enhanced Raman spectroscopic method by using a three-electrode spectroelectrochemical cell towards characterizing the electrode/polyelectrolyte interfaces.The Ag/AgCl and Ag/Ag_(2)O electrodes are used as the reference electrode in the acidic and the alkaline systems,respectively.The working electrode is made of a transparent carbon thin film which loads the electrocatalysts.The applications of this method are demonstrated through the in-situ characterizations of the p-methylthiophenol adsorbed on the Au and Pt and the electrochemical oxidation of Au on polyelectrolyte membranes.The potential-dependent spectral features of these two systems show that this method is a powerful tool for investigating the electrode/polyelectrolyte interfaces in electrocatalysis.展开更多
N-doped porous carbon has been extensively investigated for broad electrochemical applications.The performance is significantly impacted by the electrochemical double layer(EDL),which is material dependent and hard to...N-doped porous carbon has been extensively investigated for broad electrochemical applications.The performance is significantly impacted by the electrochemical double layer(EDL),which is material dependent and hard to characterize.Limited understanding of doping-derived EDL structure hinders insight into the structure-performance relations and the rational design of high-performance materials.Thus,we analyzed the mass and chemical composition variation of EDL within electrochemical operation by electrochemical quartz crystal microbalance,in-situ X-ray photoelectron spectroscopy,and time-offlight secondary ion mass spectrometry.We found that N-doping triggers specifically adsorbed propylene carbonate solvent in the inner Helmholtz plane(IHP),which prevents ion rearrangement and enhances the migration of cations.However,this specific adsorption accelerated solvent decomposition,rendering rapid performance degradation in practical devices.This work reveals that the surface chemistry of electrodes can cause specific adsorption of solvents and change the EDL structure,which complements the classical EDL theory and provide guidance for practical applications.展开更多
The electrocatalytic conversion of reactive nitrogen species to ammonia is a promising strategy for efficient NH_(3) synthesis.In this study,we reveal that the hybrid Cu^(+)/Cu~0 interface is catalytically active for ...The electrocatalytic conversion of reactive nitrogen species to ammonia is a promising strategy for efficient NH_(3) synthesis.In this study,we reveal that the hybrid Cu^(+)/Cu~0 interface is catalytically active for electrochemical ammonia synthesis from nitrate reduction.To maintain the hybrid Cu^(+)/Cu~0 state at negative reaction potentials,hydrophilic zeolite is used to modify Cu/Cu_(2)O electrocatalyst,which demonstrates an impressive NH_(3) production rate of 41.65 mg h^(-1) cm^(-2)with ~100% Faradaic efficiency of ammonia synthesis at-0.6 V vs.RHE.In-situ Raman spectroscopy unveil the high activity originates from the zeolite reconstruction at the electrode–electrolyte interface,which protects the valence state of Cu~0/Cu^(+) site under negative potential and promotes electrochemical activity towards NH_(3) synthesis.展开更多
Bimetallic catalysts can improve CO2 reduction efficiency via the combined properties of two metals.CuPd shows enhanced CO2 reduction activity compared to copper alone.Using differential electrochemical mass spectrome...Bimetallic catalysts can improve CO2 reduction efficiency via the combined properties of two metals.CuPd shows enhanced CO2 reduction activity compared to copper alone.Using differential electrochemical mass spectrometry(DEMS)and electrochemical infrared(IR)spectroscopy,volatile products and adsorbed intermediates were measured during CO2 and CO reduction on Cu and CuPd.The IR band corresponding to adsorbed CO appears 300 mV more positive on CuPd than that on Cu,indicating acceleration of CO2 reduction to CO.Electrochemical IR spectroscopy measurements in CO-saturated solutions reveal similar potentials for CO adsorption and CO3^2-desorption on CuPd and Cu,indicating that CO adsorption is controlled by desorption of CO3^2-.DEMS measurements carried out during CO reduction at both electrodes showed that the onset potential for reduction of CO to CH4 and CH3OH on CuPd is about 200 mV more positive than that on Cu.We attribute these improvements to interaction of Cu and Pd,which shifts the d-band center of the Cu sites.展开更多
A comprehensive understanding of the microscopic reaction mechanisms at the gas-solid-liquid electrochemical interfaces is urgently required for the development of advanced electrocatalysts applied in burgeoning susta...A comprehensive understanding of the microscopic reaction mechanisms at the gas-solid-liquid electrochemical interfaces is urgently required for the development of advanced electrocatalysts applied in burgeoning sustainable energy conversion systems. In-situ synchrotron radiation Fourier transform infrared(SR-FTIR) spectroscopy is one of the most powerful techniques for investigating the evolving dynamics of reactive intermediates during electrocatalytic reactions. In this review, we methodically summarize the recent progress in the research of dynamic mechanisms for valuable electrocatalytic reactions based on in-situ SR-FTIR methodology. Moreover, the merits and drawbacks of SRFTIR spectroscopy, the design principles of infrared beam setups and in-situ cells, as well as the in-situ measurement criteria are also discussed in detail. Lastly, the potential challenges and opportunities in this field are prudently stated. This review is expected to stimulate a broad interest in the material science and electrochemistry communities for exploring the dynamic mechanisms of prominent catalysis at the atomic/molecular level by using SR-based spectroscopy.展开更多
Replacing conventional fossil resources with renewable raw materials for chemical production and energy generation is crucial for achieving the carbon-neutral goal and alleviating the emerging energy crisis.Biomass ha...Replacing conventional fossil resources with renewable raw materials for chemical production and energy generation is crucial for achieving the carbon-neutral goal and alleviating the emerging energy crisis.Biomass has been considered as one of the most promising candidates for this purpose owing to its great natural abundance and inherent ability to fix CO_(2) in the form of multicarbon compounds.Particularly,biomass conversion through an electrochemical route is intriguing because of its operability near ambient conditions,flexible scalability(suitable for distributed manufacturing and even domestic use)and green generation of oxidative or reductive equivalents instead of wasteful and possibly explosive or flammable reagents.Herein,recent progress in electrochemical transformation of biomass,including hydrogenation and amination,is reviewed with the emphasis on catalysts and strategies for enhancing catalytic efficiency.The advances in mechanistic understanding using in-situ spectroscopy are also briefly discussed.Finally,recommendations for the directions for future development are also provided.展开更多
文摘Methanol oxidation reaction （MOR） at Pt and Pt electrode surface deposited with various amounts of Ru （denoted as PtxRuy, nominal coverage y is 0.17, 0.27, and 0.44 ML） in 0.1 mol/L HClO4＋0.5 mol/L MeOH has been studied under potentiostatic conditions by in situ FTIR spectroscopy in attenuated-total-reflection con guration and di erential electro-chemical mass spectrometry under controlled flow conditions. Results reveal that （i） CO is the only methanol-related adsorbate observed by IR spectroscopy at all the Pt and PtRu electrodes examined at potentials from 0.3 V to 0.6 V （vs. RHE）; （ii） at Pt0.56Ru0.44, two IR bands, one from CO adsorbed at Ru islands and the other from COL at Pt substrate are detected, while at other electrodes, only a single band for COL adsorbed at Pt is observed; （iii） MOR activity decreases in the order of Pt0.73Ru0.27〉Pt0.56Ru0.44〉Pt0.83Ru0.17〉Pt; （iv） at 0.5 V, MOR at Pt0.73Ru0.27 reaches a current e ciency of 50% for CO2 production, the turn-over frequency from CH3OH to CO2 is ca. 0.1 molecule/（site sec）. Suggestions for further improving of PtRu catalysts for MOR are provided.
文摘Infrared(IR)absorption spectroscopy has been widely used for dynamic characterization of catalysts and mechanism of catalytic reactions.However,due to the strong infrared absorption of heterogeneous catalysts(mainly oxides,or supported metal and metal oxides,etc.)below 1200 cm^(-1),and the intensity of regular infrared light source rapidly decays at low-wavenumber range,most in-situ infrared spectroscopy studies are limited to the detection of surface adsorbates in the range of 4000-900 cm^(-1).The change of catalytically active component itself(M-O,M-M bond,etc.,1200-50 cm^(-1))during the reaction is hard to be tracked under reaction conditions by in-situ IR.In this work,a home-made in-situ IR reactor was designed and a sample preparing method was developed.With such progresses,the changes of reactants,products,surface adsorbates,and catalysts themselves can be measured under the same reaction conditions with a spectral range of 4000-400 cm^(-1),providing a new opportunity for in-situ characterization of heterogeneous catalysis.CO oxidation on Pd/SiO_(2) and Cu/SiO_(2) catalysts were taken as examples,since both the two catalytic systems were extensively used commercially,and moreover reduction and oxidation of palladium and copper occur during the examined reaction conditions.The characteristic bands of Pd^(2+)-O(670,608 cm^(-1)),Cu^(+)-O(635 cm^(-1))and Cu^(2+)-O(595,535 cm^(-1))were observed by IR,and the changes during CO oxidation reaction were successfully monitored by IR.The oxidation/reduction of palladium and copper were also confirmed by ex-situ XPS.Moreover,Pd^(0) in Pd/SiO_(2) and Cu^(+)in Cu/SiO_(2) were found as the thermal dynamically stable phases under the examined conditions for CO oxidation.
文摘Polyelectrolyte becomes more and more popular in electrocatalysis.The understanding of electrode/polyelectrolyte interfaces at the molecular level is important for guiding further the polyelectrolyte-based electrocatalysis.Herein,we demonstrate an in-situ surface-enhanced Raman spectroscopic method by using a three-electrode spectroelectrochemical cell towards characterizing the electrode/polyelectrolyte interfaces.The Ag/AgCl and Ag/Ag_(2)O electrodes are used as the reference electrode in the acidic and the alkaline systems,respectively.The working electrode is made of a transparent carbon thin film which loads the electrocatalysts.The applications of this method are demonstrated through the in-situ characterizations of the p-methylthiophenol adsorbed on the Au and Pt and the electrochemical oxidation of Au on polyelectrolyte membranes.The potential-dependent spectral features of these two systems show that this method is a powerful tool for investigating the electrode/polyelectrolyte interfaces in electrocatalysis.
基金the National Science Foundation for Excellent Young Scholars of China(21922815)the National Natural Science Foundation of China(22179139)+2 种基金the National Key Research and Development Program of China(2020YFB1505800)the Youth Innovation Promotion Association of CAS(2019178)the“Transformational Technologies for Clean Energy and Demonstration”Strategic Priority Research Program of the CAS(XDA21000000)。
文摘N-doped porous carbon has been extensively investigated for broad electrochemical applications.The performance is significantly impacted by the electrochemical double layer(EDL),which is material dependent and hard to characterize.Limited understanding of doping-derived EDL structure hinders insight into the structure-performance relations and the rational design of high-performance materials.Thus,we analyzed the mass and chemical composition variation of EDL within electrochemical operation by electrochemical quartz crystal microbalance,in-situ X-ray photoelectron spectroscopy,and time-offlight secondary ion mass spectrometry.We found that N-doping triggers specifically adsorbed propylene carbonate solvent in the inner Helmholtz plane(IHP),which prevents ion rearrangement and enhances the migration of cations.However,this specific adsorption accelerated solvent decomposition,rendering rapid performance degradation in practical devices.This work reveals that the surface chemistry of electrodes can cause specific adsorption of solvents and change the EDL structure,which complements the classical EDL theory and provide guidance for practical applications.
基金the support from the Fundamental Research Funds for the Central Universities (2022LHJH01-03, 2022ZFJH04, 2022QZJH14)Pioneer R&D Program of Zhejiang Province (2022C03040)+1 种基金the Ecological civilization project, Zhejiang Universitythe support from A Project Supported by Scientific Research Fund of Zhejiang University (XY2022013)。
文摘The electrocatalytic conversion of reactive nitrogen species to ammonia is a promising strategy for efficient NH_(3) synthesis.In this study,we reveal that the hybrid Cu^(+)/Cu~0 interface is catalytically active for electrochemical ammonia synthesis from nitrate reduction.To maintain the hybrid Cu^(+)/Cu~0 state at negative reaction potentials,hydrophilic zeolite is used to modify Cu/Cu_(2)O electrocatalyst,which demonstrates an impressive NH_(3) production rate of 41.65 mg h^(-1) cm^(-2)with ~100% Faradaic efficiency of ammonia synthesis at-0.6 V vs.RHE.In-situ Raman spectroscopy unveil the high activity originates from the zeolite reconstruction at the electrode–electrolyte interface,which protects the valence state of Cu~0/Cu^(+) site under negative potential and promotes electrochemical activity towards NH_(3) synthesis.
基金supported by the National Natural Science Foundation of China(No.91545124 and No.21750110437)supported by the Chinese Academy of Sciences President’s International Fellowship Initiative(No.2017PM0049)。
文摘Bimetallic catalysts can improve CO2 reduction efficiency via the combined properties of two metals.CuPd shows enhanced CO2 reduction activity compared to copper alone.Using differential electrochemical mass spectrometry(DEMS)and electrochemical infrared(IR)spectroscopy,volatile products and adsorbed intermediates were measured during CO2 and CO reduction on Cu and CuPd.The IR band corresponding to adsorbed CO appears 300 mV more positive on CuPd than that on Cu,indicating acceleration of CO2 reduction to CO.Electrochemical IR spectroscopy measurements in CO-saturated solutions reveal similar potentials for CO adsorption and CO3^2-desorption on CuPd and Cu,indicating that CO adsorption is controlled by desorption of CO3^2-.DEMS measurements carried out during CO reduction at both electrodes showed that the onset potential for reduction of CO to CH4 and CH3OH on CuPd is about 200 mV more positive than that on Cu.We attribute these improvements to interaction of Cu and Pd,which shifts the d-band center of the Cu sites.
基金supported by the National Natural Science Foundation of China (Nos. 1932212, U1932109, 11875257)。
文摘A comprehensive understanding of the microscopic reaction mechanisms at the gas-solid-liquid electrochemical interfaces is urgently required for the development of advanced electrocatalysts applied in burgeoning sustainable energy conversion systems. In-situ synchrotron radiation Fourier transform infrared(SR-FTIR) spectroscopy is one of the most powerful techniques for investigating the evolving dynamics of reactive intermediates during electrocatalytic reactions. In this review, we methodically summarize the recent progress in the research of dynamic mechanisms for valuable electrocatalytic reactions based on in-situ SR-FTIR methodology. Moreover, the merits and drawbacks of SRFTIR spectroscopy, the design principles of infrared beam setups and in-situ cells, as well as the in-situ measurement criteria are also discussed in detail. Lastly, the potential challenges and opportunities in this field are prudently stated. This review is expected to stimulate a broad interest in the material science and electrochemistry communities for exploring the dynamic mechanisms of prominent catalysis at the atomic/molecular level by using SR-based spectroscopy.
基金the Monash-Warwick Alliance for funding support through the Accelerator Fund。
文摘Replacing conventional fossil resources with renewable raw materials for chemical production and energy generation is crucial for achieving the carbon-neutral goal and alleviating the emerging energy crisis.Biomass has been considered as one of the most promising candidates for this purpose owing to its great natural abundance and inherent ability to fix CO_(2) in the form of multicarbon compounds.Particularly,biomass conversion through an electrochemical route is intriguing because of its operability near ambient conditions,flexible scalability(suitable for distributed manufacturing and even domestic use)and green generation of oxidative or reductive equivalents instead of wasteful and possibly explosive or flammable reagents.Herein,recent progress in electrochemical transformation of biomass,including hydrogenation and amination,is reviewed with the emphasis on catalysts and strategies for enhancing catalytic efficiency.The advances in mechanistic understanding using in-situ spectroscopy are also briefly discussed.Finally,recommendations for the directions for future development are also provided.
基金supported by the National Natural Science Foundation of China(51131005,51171172,50801056)Natural Science Foundation of Zhejiang Province,China(Y4110074)~~
