Photo-Grafting Copolymerization of PP Nonwoven Fabric and Its Application for Acidic Dye Adsorption and Filtration

The monomer methacrylamido propyl trimethy ammonium chloride( MAPTAC) was copolymerized onto the fiber surface of polypropylene( PP) nonwoven fabric under ultroviole radiation. The weak acid red GN dye adsorption and adsorptive filtration performance of the resulted PP fabrics were investigated.The results showed that the grafting copolymerization preferred to happen in the inner layer of the fabrics. The water flux of the grafted fabrics decreases with the increase of grafting yield. The collapse of the grafted polymer chains causes the flux increase in acidic condition,or vice versa at alkaline version. The coiling of the polyelectrolyte chains upon the dye adsorption seems to violate the routine assumption of the rigid substrate, and this gets the adsorption energy constant negative. The static adsorption process follows the Lagergren's pseudo-second order kinetic equation. The removals of circa( ca.) 100% of the total permeation volume3 500 mL simulated dye wastewater was reached during permeation.The dye adsorbed fabrics were regenerated by the mixed media of the cationic surfactant / ethanol /water. The grafted fabric assumes stable fabric integrity and stability during permeation,and presents excellent dye adsorption capacity,easy desorption, and repeatable utilization.

Effects of two modification methods on the mechanical properties of wood flour/recycled plastic blends composites: addition of thermoplastic elastomer SEBS-g-MAH and in-situ grafting MAH

The effect of maleic anhydride grafted styrene-ethylene- buty-lene-styrene block copolymer （SEBS-g-MAH） and in-situ grafting MAH on mechanical, dynamic mechanical properties of wood flour/recycled plastic blends composites was investigated. Recycled plastic polypro-pylene （PP）, high-density polyethylene （HDPE） and polystyrene （PS）, were mixed with wood flour in a high speed blender and then extruded by a twin/single screw tandem extruder system to form wood flour/recycled plastic blends composites. Results show that the impact properties of the composites were improved more significantly by using SEBS-g-MAH compatibilizer than by using the mixtures of MAH and DCP via reactive blending in situ. However, contrary results were ob-served on the tensile and flexural properties of the corresponding com-posites. In General, the mechanical properties of composites made from recycled plastic blends were inferior to those made from virgin plastic blends, especially in elongation break. The morphological study verified that the interfacial adhesion or the compatibility of plastic blends with wood flour was improved by adding SEBS-g-MAH or in-situ grafting MAH. A better interfacial bonding between PP, HDPE, PS and wood flour was obtained by in-situ grafting MAH than the addition of SEBS-g-MAH. In-situ grafting MAH can be considered as a potential way of increasing the interfacial compatibility between plastic blends and wood flour. The storage modulus and damping factor of composites were also characterized through dynamic mechanical analysis （DMA）.

GRAFT COPOLYMERIZATION OF VINYL MONOMERS ONTO STARCH INITIATED BY TRANSITION METAL-THIOUREA REDOX SYSTEMS

In this paper, the capabilities of grafting acrylonitrile (AN) onto starch initiated by Fe(III)-TU, V(V)-TU, Cr(VI)-TU, Mn(VII)-TU redox systems were compared in the presence of sulfuric acid of different concentrations. It was shown that the grafting capability of Mn(VII)-TU is the highest in these initiating systems. Using Mn (VII-TU as initiator, the effects of various acids (HClO4, H2SO4, HNO3, HCl) on the graft copolymerization of acrylonitrile onto starch were discussed, and the capabilities of graft copolymerization of methyl methacrylate (MMA), acrylamide (AM), acrylic acid (AA) onto starch were investigated. The experimental results show that the order of the influences of different acids is HClO4 > H2SO4 > HNO3 > HCl, and the order of grafting capabilities of different monomers grafted onto starch is MMA > AN > AM > AA. The structure and morphology of graft, copolymers were studied with infrared spectroscopy and scanning electron microscopy. The size, shape and roughness of surface of the grafted starch granules are changed after grafting.

MODIFICATION OF SILK FIBER via EMULSION GRAFT COPOLYMERIZATION WITH FLUOROACRYLATE

2,2,3,3,4,4,5,5-Octafluoropentyl acrylate was grafted onto silk fiber in a two-step heterogeneous system through the vinyl bonds of acryloyloxyethyl isocyanate modified on the silk.The grafted copolylner was analyzed by FTIR and WAXD,and the results revealed that the fluoroacrylate was successfully grafted onto silk fiber and the crystalline structure of silk fibroin withβ-sheet structure was not changed after graft copolymerization.The FT-IR corrected method was used to simulate the grafting yield onto sil...

Research on the Graft Copolymerization of EH-lignin with acrylamide

Lignin isolated from enzymatic hydrolyzed corn-stalks (EH-lignin) is a renewable natural polymer noted for its versatility and applicability in a vari-ety of uses. Graft copolymerization of EH-lignin with acrylamide (AM) and the application of this copolymer as a flocculant in dye wastewater treatment were studied in this article. The influ-ences of some factors on yield of copolymer and the grafting ratio were investigated and the structure of EH-lignin/AM graft copolymer was characterized by FT-IR. According to the yield and the grafting ratio, the optimum conditions for graft copolymerization were as follows: initiator K2S2O8-Na2S2O3 with a quantity 3 wt% of EH-lignin, mass ratio of AM to EH-lignin was 2~3, reaction time 4h and temperature at 50℃. It was found that the absorption capacity of graft copolymer to two azo-dyes was enhanced with the increase of grafting ratio. Furthermore, the residue concen-tration of EH-lignin/AM graft copolymer remained in the supernatant after flocculation was much lower than that of pure EH-lignin.

Studies on Graft Copolymerization of Acrylic Acid onto Ramie Fibers with Chromic Acid Initiation System

The graft copolymerization of acrylic acid (AA) with unswollen and swollen ramie fibers using chromic acid (H 2CrO 4) as the initiator has been studied in the presence of air. The effects of initiator concentration, monomer concentration, perchloric acid (HClO 4) concentration, time of polymerization, reaction temperature, and amount of ramie fibers on the graft percentage have been found out. The graft copolymer was characterized by IR spectra, scanning electron microscopy(SEM), differential thermal analysis (DTA), and thermogravimertric analysis (TGA).

Graft Copolymerization of Ethyl Acrylate onto Hydroxypropyl Methylcellulose Using Potassium Persulfate as Initiator

With potassium persulfate (KPS) as initiator, graft copolymerization of ethyl acrylate (EA) onto water-soluble hydroxypropyl methylcellulose (HPMC) was investigated in aqueous medium. Effects of monomer concentration, initiator concentration, matrix concentration, and reaction temperature on the percentage of grafting (G) and grafting efficiency (G_E) were studied. The results show that G and G_E values both increase with the the increase of EA concentration and KPS concentration; when raising HPMC concentration from 0.12 mmol/L to 0.47 mmol/L, G decreases, while G_E increases;and when raising reaction temperature from 50 ℃ to 65 ℃,G increases, but G_E decreases. In addition, the graft copolymers were characterized by Fourier transform infrared (FTIR) spectra and transmission electron microscopy (TEM) methods.

Graft Copolymerization of N,N-Dimethylacrylamide to Cellulose in Homogeneous Media Using Atom Transfer Radical Polymerization for Hemocompatibility

In homogeneous media, N,N-Dimethylacrylamide (DMA) was grafted copolymerization to cellulose by a metal-catalyzed atom transfer radical polymerization (ATRP) process. First, cellulose was dissolved in DMAc/LiCl system, and it reacted with 2-bromoisobutyloyl bromide (BiBBr) to produce macroinitiator (cell-BiB). Then DMA was polymerized to the cellulose backbone in a homogeneous DMSO solution in presence of the cell-BiB. Characterization with FT-IR, NMR, and GPC measurements showed that there obtained a graft copolymer with cellulose backbone and PDMA side chains (cell-PDMA) in well-defined structure. The proteins adsorption studies showed that the cellulose membranes modified by the as-prepared cell-PDMA copolymer owns good protein adsorption resistancet.

Graft copolymerization of cellulose and 2-hydroxyethyl methacrylate in an ionic liquid

Dissolution and homogeneous graft copolymerization of cellulose were performed in an ionic liquid 1-allyl-3-methylimidazolium chloride （AmimCl） with 2-hydroxyethyl methacrylate. The synthesized AmimCl and cellulose graft copolymers were characterized by FTIR, ^1 H-NMR and XRD spectroscopy. The results show that AmimCl dissolved cellulose directly by destroying intermolecular and intramolecular hydrogen bonds in cellulose and the crystalline form of cellulose was transformed from cellulose Ⅰ to cellulose Ⅱ after regeneration from AmimCl. The best synthetic condition of the cellulose-graft-P （2-hydroxyethyl methacrylate） was that cellulose 0.5 g, 2-hydroxyethyl methacrylate 3.00 g and initiator ammonium persulfate 0.05 g reacted for 180 min at 60℃; the rate of grafting reached 77.3%.

Determining the degree of grafting for poly(vinylidene fluoride) graft-copolymers using fluorine elemental analysis

Acrylic acid (AAc) and styrene (St) were grafted onto poly(vinylidene fluoride) (PVDF) powder or membrane samples by pre-irradiation graft copolymerization.The grafted chains were proved by FT-IR spectroscopy analysis.The degree of grafting (DG) of the grafted PVDF was determined by fluorine elemental analysis (FEA) method,and was compared with the DGs determined by weighing method,acid-base back titration method and quantitative FT-IR method.The results show that the FEA method is accurate,convenient and universal,especially for the grafted polymer powders.

Surface Photografting of Novel Sulfobetaine Copolymers on Silica

A couple of novel sulfobetaine copolymer is developed via Michael-type addition reaction. The comonomers, diamines and maleimide react via Michael reaction through UV irradiation using AIBN as photoinitiator producing polyamine chain. Further, sulfobetaine copolymers were obtained on treatment of the polyamine with sulfopropylating agent, 1,3-propane sultone. These novel sulfobetaine polymers were grafted on silica surface to produce responsive biocompatible surface. This easy straightforward, catalyst free facile protocol for synthesis of polymer grafted surface is useful for developing biomedical devices. Additionally, both the copolymers show fluorescence characteristics.

GRAFTING OF ACRYLAMIDE ONTO SURFACE OF COPOLYMERS CONTAINING P-TOLYLCARBAMOYL PENDANT GROUP INITIATED WITH CERIC SALT

Two copolymers containing p-tolylcarbamoyl pendant group poly (MAMT-co-VAc) and poly(MAMT-co-MA) were synthesized f and the graft copolymerization of AAM onto these two func-tional copolymers films initiated with ceric salt were carried out in aqueous solution for variousperiods at 30℃. The formation of graft copolymer was verified by water absorption, ESCA andSEM photographs. Based on the results of the study of the initiation mechanism of model com-pounds and ceric salt systems, the reaction mechanism of the graft copolymerization initiated withceric salt was proposed.

Graft Copolymerization of Modified Oxidized Starch and Its ER Effect

To enhance the polarization of starch, the oxidized starch-BA-MAA-Gd copolymer was synthesized by radical graft copolymerization. The structure of the graft copolymer was determined by IR, scanning electron microscopy, state thermal analysis and X-ray diffraction. The electrorheological properties of the graft copolymer were also investigated. The results show that shear stress increases with the increase of the graft copolymer loadings and the electric field intensity.

THE EFFECTS OF MAGNETIC FIELD ON GRAFT COPOLYMERIZATION OF METHYL METHACRYLATE ONTO POLYVINYL ALCOHOL IN THE PRESENCE OF BENZOPHENONE DURING UV IRRADIATION

The effects of magnetic field on the graft ratio and stereoregularity of grafts of PVA-g-MMA in the presence ofbenzophenone during UV irradiation are discussed. By means of IR, it was found that the graft ratio was increased with the increment of magnetic field strength. Furthermore, application of relative weak magnetic field of 0.4 Tesla had been shown to substantially enhance the stereo-regularity of graft copolymer. The maximum stereo-regularity appeared when the graft ratio approached to 85% with the magnetic field of 1.2 Tesla (T). The resistance to moisture and heat resistance of the grafted copolymer in the presence of magnetic field were also improved.

RADICAL GRAFTING REACTIONS ONTO STARCH AND OTHER WATER-SOLUBLE COPOLYMERS IN ISOLATED GEL DROPLETS

A novel radical grafting copolymerization process has been designed for water-soluble polymers which avoids the problems of conducting grafting reactions in highly viscous polymerization media. A variety of water-soluble graft copolymers having starch or dextran as the backbone chain with grafted side chains of polyacrylamide (—AM—), poly (acrylic acid ) (—AA—), poly (acrylamide-co-acrylic acid) (—AM—NH_4AA—) or poly ( acrylamide-co-2-acryiamido-2-methyl-l-propanesulphinic acid) (—AM—AMPS—) have been synthesized in gel droplets using aceric sulphate redox initiator, and their properties compared. The reaction conditions were optimized taking into account reaction kinetic data and the observed properties of the products produced under different reaction conditions. The effects of the ratios of [backbone]/[graft monomer], [ AM]/[ AA]/[AMPS] , [Ce^(4+)]/[ S_2O_8=] and pH value on the reaction rate , conversion, grafting degree, grafted chain length and the product molecular weight have been investigated.

Studies on the Graft Copolymerization of Methyl Acrylate and Ethyl Acrylate onto Corn Starch Using Potassium Persulfate-Sodium Thiosulphatc as Initiation System

Grafting copolymerizations of methyl acrylate(MA) and ethyl acrylate(EA) onto corn starch, respectively, initiated by potassium persulfate-sodium thiosulphate (KPS-STS) redox system, were studied. The structures of poly(MA)-g-starch and poly(EA)-g-starch were characterized by IR, SEM and X-ray diffraction. Experimental results show that KPS-STS is an efficient initiation system for grafting of MA and EA onto corn starch. The maximum percent grafting was obtained at [KPS] of 6.0× 10~3 mol/L, [STS] of 1.8× 10 5 mol/L, [M] of 6. 0× 101 mol/L, S:L=4:100 at 40℃ for 6 h. The reactivity order is MA>EA.

Starch Modification by Graft Copolymerization of Acrylonitrile

The graft copolymerization of acrylonitrile (AN) onto starch under the initiation of potassium permanganate was investigated. The effect of various reaction conditions on the graft copolymerization was studied. The relationships between the grafting rate and the initiator concentration of potassium permanganate, monomer acrylonitrile and backbone starch, as well as reaction temperature were established. The oxidation reaction of starch with manganic ions and valence changes of manganic ions during the graft copolymerization were discussed. The results show that manganic ion Mn 7+ underwent a series of valence changes during the graft copolymerization: Mn(Ⅶ) → Mn(Ⅳ) → Mn(Ⅲ) → Mn(Ⅱ). The grafting rate of the graft copolymerization of acrylonitrile onto starch is also given.

Preparation of superabsorbent by graft copolymerization of acrylic acid onto corn starch using K_2S_2O_8 and rare earths as initiators

K2 S2 O8 and rare earths （RE） were used as initiators to prepare superabsorbents by graft copolymerization of acrylic acid （ AA ） onto corn starch. The effects of monomer concentration, initiator K2 S2 O8 concentration, cross-linker concentration, reaction temperature and the concentration ratio of RE and K2 S2O8 on the graft copolymerization were studied in terms of the water absorption capacity of superabsorbents. Results indicate that the optimum conditions obtained for the grafting of AA onto 5g starch are as follows： AA of 75. 773 g/L, K2S20s of 0. 437 g/L, RE of 0. 874 g/L, cross-linker of 0. 381 g/L and temperature of 70 ℃. The maximum water absorption capacity obtained is 740 g/g. The new method of graft polymerization is easily proceeded and controlled. The graft copolymers were characterized by infra-red spectroscopy, scanning electron microscopy and TG. Results characterized by IR and SEM give strong evidence for grafting of AA onto corn starch, and those characterized by TG reveal that the grafting of AA improves the theimostability of corn starch.

Modification of Natural Rubber Latex by Graft Copolymerization of 2-Ethylhexyl Acrylate and Methacrylic Acid

Natural rubber(NR)grafted with 2-ethylhexyl acrylate(2-EHA)and methacrylic acid(MAA,collectively NR-g-PEHA/MAA)was synthesized by emulsion polymerization.Tetraethylenepentamine and cumene hydroperoxide were used as redox initiators.The successful grafting of 2-EHA and MAA onto NR was confirmed by Fourier transform infrared spectroscopy.The morphology of the NR latex particles was observed by transmission electron microscopy.The effects of reaction temperature,initiator dosage,feeding mode,and hard monomer content on the mechanical properties of the modified NR film were investigated.Grafted polymer chains were unevenly wrapped on the outside of NR particles,and smaller particles were more easily grafted.Crosslinking was characterized using a toluene swelling method.Thermal stability and glass transition temperature were examined by differential scanning calorimetry and thermogravimetric analysis.The results showed that the thermal stability of NR-g-PEHA/MAA had been improved,and the glass transition temperature(Tg)was unchanged.

The Optimized Synthesis of Starch-g-Lactic Acid Copolymer with High Grafting Degree Catalyzed by Sulfuric Acid

The starch-g-lactic acid copolymer was synthesized with catalysis of sulfuric acid by onestep process, and the structure of starch-g-lactic acid copolymer was characterized by means of IR, 13C-NMR, HMBC, XRD, and SEM. The experimental results show that the maximum grafting degree of starch can reach 75% when the starch-g-lactic acid copolymer is activated at 80 ℃ for 2 h and reacted with lactic acid at 90 ℃ for 4 h in vacuum.