Support design method for deep soft-rock tunnels in non-hydrostatic high in-situ stress field

Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunnels will suffer serious asymmetric deformation.There is no available support design method for tunnels under such a situation in existing studies to clarify the support time and support stiffness.This study first analyzed the mechanical behavior of tunnels in non-hydrostatic in-situ stress field and derived the theoretical equations of the ground squeezing curve(GSC)and ground loosening curve(GLC).Then,based on the convergence confinement theory,the support design method of deep soft-rock tunnels under non-hydrostatic high in-situ stress field was established considering both squeezing and loosening pressures.In addition,this method can provide the clear support time and support stiffness of the second layer of initial support.The proposed design method was applied to the Wanhe tunnel of the China-Laos railway in China.Monitoring data indicated that the optimal support scheme had a good effect on controlling the tunnel deformation in non-hydrostatic high in-situ stress field.Field applications showed that the secondary lining could be constructed properly.

A review of in-situ high-temperature characterizations for understanding the processes in metallurgical engineering

For the rational manipulation of the production quality of high-temperature metallurgical engineering,there are many challenges in understanding the processes involved because of the black box chemical/electrochemical reactors.To overcome this issue,various in-situ characterization methods have been recently developed to analyze the interactions between the composition,microstructure,and solid-liquid interface of high-temperature electrochemical electrodes and molten salts.In this review,recent progress of in-situ hightemperature characterization techniques is discussed to summarize the advances in understanding the processes in metallurgical engineering.In-situ high-temperature technologies and analytical methods mainly include synchrotron X-ray diffraction(s-XRD),laser scanning confocal microscopy,and X-ray computed microtomography(X-rayμ-CT),which are important platforms for analyzing the structure and morphology of the electrodes to reveal the complexity and variability of their interfaces.In addition,laser-induced breakdown spectroscopy,high-temperature Raman spectroscopy,and ultraviolet-visible absorption spectroscopy provide microscale characterizations of the composition and structure of molten salts.More importantly,the combination of X-rayμ-CT and s-XRD techniques enables the investigation of the chemical reaction mechanisms at the two-phase interface.Therefore,these in-situ methods are essential for analyzing the chemical/electrochemical kinetics of high-temperature reaction processes and establishing the theoretical principles for the efficient and stable operation of chemical/electrochemical metallurgical processes.

Fabrication of Au/SiO_(2) Nanocomposite Films by Self-Assembly Multilayer Method

Gold colloid was prepared by chemical reduction of hydrogen tetrachloroaurate, polyelectrolyte/gold nanoparticle/silica nanoparticie composite films were fabricated via an electrostatic self-assembly multilayer method, and composite films of gold nanoparticle dispersed in silica matrix were formed by heat-treating the polyelectrolyte/gold nanoparticle/silica nanoparticle composite films to eliminate the polyelectrolyte. The obtained composite films were investigated with UV-vis, TEM, AFM and XRD. The results show that the self-assembly multilayer method is a promising process to produce composite films of gold nanoparticle-dispersed in organic and/or inorganic matrixes.

Preparation of PVA/GO/h-BN Janus Film with High Thermal Conductivity and Excellent Flexibility via a Density Deposition Self-assembly Method

Janus films with asymmetric physical/chemical properties have attracted con siderable attention due to their promising applications in personal thermal management,electronic skin s,sensors,actuators,etc.However,traditional methods for fabricating Janus films conventionally need the assistance of an interface or auxiliary equipment,which are usually complex and time-consuming.Herein,flexible poly(vinyl alcohol)(PVA)/graphene oxide(GO)/h-BN(recorded as PVA/GO/h-BN)Janus films with thermally,optically,and electrically anisotropic properties are fabricated by a simple density deposition self-assem bly method,which just utilizes the density difference between GO and h-BN during water evaporation.Experimental results show that the two sides of the acquired Janus films have obvious asymmetric characteristics.In the original state of the PVA/GO/h-BN Janus films,the thermal conductivity of the GO side(10.06 W·m^(-1)·K^(-1))is generally lower than that of the h-BN side(10.48W·m^(-1)·K^(-1)).But after GO is reduced,the thermal conductivity of the rGO side reaches 12.17 W·m^(-1)·K^(-1),surpassing that of the h-BN side.In addition,the relative reflectance of the h-BN side of Janus film is also significantly higher than that of the rGO side,and the su rface resistance difference between the two sides is about 4 orders of magnitude.The prepared PVA/GO/h-BN Janus films show great application potential in human thermal management,light conversion switches,and electronic skins.This study provides a simple and versatile strategy for fabricating Janus films with multifunctional(such as thermal,optical,and electrical)anisotropies.

Stress initialization methods for dynamic numerical simulation of rock mass with high in-situ stress

In the context of deep rock engineering,the in-situ stress state is of major importance as it plays an important role in rock dynamic response behavior.Thus,stress initialization becomes crucial and is the first step for the dynamic response simulation of rock mass in a high in-situ stress field.In this paper,stress initialization methods,including their principles and operating procedures for reproducing steady in-situ stress state in LS-DYNA,are first introduced.Then the most popular four methods,i.e.,explicit dynamic relaxation(DR)method,implicit-explicit sequence method,Dynain file method and quasi-static method,are exemplified through a case analysis by using the RHT and plastic hardening rock material models to simulate rock blasting under in-situ stress condition.Based on the simulations,it is concluded that the stress initialization results obtained by implicit-explicit sequence method and dynain file method are closely related to the rock material model,and the explicit DR method has an obvious advantage in solution time when compared to other methods.Besides that,it is recommended to adopt two separate analyses for the whole numerical simulation of rock mass under the combined action of in-situ stress and dynamic disturbance.

A Facile Self-assembly Synthesis of Hexagonal ZnO Nanosheet Films and Their Photoelectrochemical Properties

Here, large-scale and uniform hexagonal zinc oxide(ZnO) nanosheet films were deposited onto indium tin oxide(ITO)-coated transparent conducting glass substrates via a facile galvanic displacement deposition process. Compared with other commonly used solution methods, this process avoids high temperature and electric power as well as supporting agents to make it simple and cost-effective. The as-fabricated ZnO nanosheet films have uniform hexagonal wurtzite structure. The photoelectrochemical(PEC) cell based on ZnO nanosheet film/ITO photoelectrode was also fabricated and its performance was improved by optimizing the solution concentration. A higher photocurrent density of*500 l A cm^(-2)under AM 1.5 G simulated illumination of 100 m W cm^(-2)with zero bias potential(vs. Ag/AgCl electrode) was obtained, which may ascribe to the increased surface-to-volume ratio of disordered Zn O nanosheet arrays. Our developed method may be used to deposit other oxide semiconductors, and the Zn O nanosheet film/ITO PEC cell can be used to design low-cost optoelectronic and photoelectrochemical devices.

Analysis on method for effective in-situ stress measurement in hot dry rock reservoir

With the rapid increase of energy demand and the increasingly highlighted environmental problems, clean, safe and widely distributed geothermal resources have become a hot spot for renewable resources development. The state of in-situ stress is a major control parameter for multiple links including well location, fracture inspiration and reservoir assessment, so how to determine the accurate state of in-situ stress in the deep thermal reservoir becomes a core problem drawing widely attention and urgent to be solved. Based on features of hot dry rock reservoir in terms of temperature and pressure and the comparison analysis, this article proposes the method of Anelastic Strain Recovery(ASR) as an effective method for determining the state of in-situ stress in the area with HDR resources distributed and explains the availability of ASR method by application examples.

Research of in-situ hydraulic test method by using double packer equipment

Double packer equipment for hydraulic test can be used to measure pressure of test zone directly, and it is frequently used to perform many kinds of hydraulic tests and take groundwater sample from borehole. The test method of this equipment mainly includes the test design, implementation, interpretation and synthetic analysis. By adopting the double packer equipment for hydraulic test, the parameter distribution of rock permeability along borehole can be acquired, as well as the connectivity, water conductivity and water bearing capacity of the disclosed structure and the chemical characteristics of the deep groundwater. It is a necessary method for the research and evaluation of the complex hypotonicity terrace site selection under geological conditions. This method is not only suitable for the geological disposal of high level radioactive waste, but also can be used in the site selection of underground facilities such as storage of petroleum and carbon dioxide. Meanwhile, it has a good application prospect in other hydrogeological investigation fields.

In-situ Characterization of Non-aqueous Nano-dispersion Systems by Freeze-etching TEM and Comparative Study with Laser Scattering Method

In-situ characterization of non-aqueous nano-dispersion systems（NANDS） by freeze-etching transmission electron microscope（FETEM） was reported.To improve just-for-once successive rate of specimen preparation and get good characterization results,an improving specimen preparation method of freezing etching was developed.Size,distribution and morphology of NANDS were directly visualized.Some information of particle dispersion feature and particle density can also be obtained.Reproductivity of the FETEM characterization is excellent.Comparing with laser scattering method,which is liable to give positive error especially for small size particle anchoring disperser,FETEM characterization can give more accurate measurement of particle size.Moreover,FETEM can give dispersion feature of nanoparticle in non-aqueous medium.

A Simple Deposition Method for Self-Assembling Single Crystalline Hybrid Perovskite Nanostructures

A sequential deposition method is developed, where the hybrid organic-inorganic halide perovskite （CH3NH3Pb （I1-xBrx）3 ） is synthesized using precursor solutions containing CH3NH3I and PbBr2 with different mole ratios and reaction times. The perovskite achieved here is quite stable in the atmosphere for a relatively long time without noticeable degradation, and the perovskite nanowires are proved to be single crystalline structure, based on transmission electron microscopy.Furthermore, strong red photoluminescence from perovskite is observed in the wavelength range from 746nm to 770nm with the increase of the reaction time, on account of the exchanges between I- ions and Br- ions in the perovskite crystal. Lastly, the influences of concentration and reaction time of the precursor solutions are discussed, which are important for evolution of hybrid perovskite from nanocuboid to nanowire and nanosheet.

In-situ gas contents of a multi-section coal seam in Sydney basin for coal and gas outburst management

The gas content is crucial for evaluating coal and gas outburst potential in underground coal mining. This study focuses on investigating the in-situ coal seam gas content and gas sorption capacity in a representative coal seam with multiple sections (A1, A2, and A3) in the Sydney basin, where the CO_(2) composition exceeds 90%. The fast direct desorption method and associated devices were described in detail and employed to measure the in-situ gas components (Q_(1), Q_(2), and Q_(3)) of the coal seam. The results show that in-situ total gas content (Q_(T)) ranges from 9.48 m^(3)/t for the A2 section to 14.80 m^(3)/t for the A3 section, surpassing the Level 2 outburst threshold limit value, thereby necessitating gas drainage measures. Among the gas components, Q_(2) demonstrates the highest contribution to Q_(T), ranging between 55% and 70%. Furthermore, high-pressure isothermal gas sorption experiments were conducted on coal samples from each seam section to explore their gas sorption capacity. The Langmuir model accurately characterizes CO_(2) sorption behavior, with ft coefcients (R^(2)) greater than 0.99. Strong positive correlations are observed between in-situ gas content and Langmuir volume, as well as between residual gas content (Q_(3)) and sorption hysteresis. Notably, the A3 seam section is proved to have a higher outburst propensity due to its higher Q_(1) and Q_(2) gas contents, lower sorption hysteresis, and reduced coal toughness f value. The insights derived from the study can contribute to the development of efective gas management strategies and enhance the safety and efciency of coal mining operations.

In-situ stress of coal reservoirs in the Zhengzhuang area of the southern Qinshui Basin and its effects on coalbed methane development

In-situ stress is a critical factor influencing the permeability of coal reservoirs and the production capacity of coalbed methane(CBM)wells.Accurate prediction of in-situ stress and investigation of its influence on coal reservoir permeability and production capacity are significant for CBM development.This study investigated the CBM development zone in the Zhengzhuang area of the Qinshui Basin.According to the low mechanical strength of coal reservoirs,this study derived a calculation model of the in-situ stress of coal reservoirs based on the multi-loop hydraulic fracturing method and analyzed the impacts of initial fractures on the calculated results.Moreover,by combining the data such as the in-situ stress,permeability,and drainage and recovery data of CBM wells,this study revealed the spatial distribution patterns of the current in-situ stress of the coal reservoirs and discussed the impacts of the insitu stress on the permeability and production capacity.The results are as follows.(1)Under given fracturing pressure,longer initial fractures are associated with higher calculated maximum horizontal principal stress values.Therefore,ignoring the effects of the initial fractures will cause the calculated values of the in-situ stress to be less than the actual values.(2)As the burial depth increases,the fracturing pressure,closure pressure,and the maximum and minimum horizontal principal stress of the coal reservoirs in the Zhengzhuang area constantly increase.The average gradients of the maximum and minimum horizontal principal stress are 3.17 MPa/100 m and 2.05 MPa/100 m,respectively.(3)Coal reservoir permeability is significantly controlled by the magnitude and state of the current in-situ stress.The coal reservoir permeability decreases exponentially with an increase in the effective principal stress.Moreover,a low lateral pressure coefficient(less than 1)is associated with minor horizontal compressive effects and high coal reservoir permeability.(4)Under similar conditions,such as resource endowments,CBM well capacity is higher in primary structural coal regions with moderate paleotectonic stress modification,low current in-situ stress,and lateral pressure coefficient of less than 1.

DDM regression analysis of the in-situ stress field in a non-linear fault zone

A multivariable regression analysis of the in-situ stress field, which considers the non-linear deformation behavior of faults in practical projects, is presented based on a newly developed three-dimensional displacement discontinuity method （DDM） program. The Bar- ton-Bandis model and the Kulhaway model are adopted as the normal and the tangential deformation model of faults, respectively, where the Mohr-Coulomb failure criterion is satisfied. In practical projects, the values of the mechanical parameters of rock and faults are restricted in a bounded range for in-situ test, and the optimal mechanical parameters are obtained from this range by a loop. Comparing with the traditional finite element method （FEM）, the DDM regression results are more accurate.

In-situ determination of onset lithium plating for safe Li-ion batteries

Lithium plating in working batteries has attracted wide attention in the exploration of safe energy storage. Establishing an effective and rapid early-warning method is strongly considered but quite challenging since lithium plating behavior is determined by diverse factors. In this contribution, we present a non-destructive electrochemical detection method based on transient state analysis and threeelectrode cell configuration. Through dividing the iR drop value by the current density, the as-obtained impedance quantity(R_(i)) can serve as a descriptor to describe the change of electrochemical reaction impedance on the graphite anode. The onset of lithium plating can be identified from the sharp drop of R_(i). Once the dendritic plated lithium occurs, the extra electrochemical reactions at the lithium interfaces leads to growing active area and reduced surface resistance of the anode. We proposed a protocol to operate the batteries under the limited capacity, which renders the cell with 98.2% capacity retention after 1000 cycles without lithium plating. The early-warning method has also been validated in in-situ optical microscopy batteries and practical pouch cells, providing a general but effective method for online lithium plating detection towards safe batteries.

Slope analysis based on local strength reduction method and variable-modulus elasto-plastic model

Employing an ideal elasto-plastic model,the typically used strength reduction method reduced the strength of all soil elements of a slope.Therefore,this method was called the global strength reduction method(GSRM).However,the deformation field obtained by GSRM could not reflect the real deformation of a slope when the slope became unstable.For most slopes,failure occurs once the strength of some regional soil is sufficiently weakened; thus,the local strength reduction method(LSRM)was proposed to analyze slope stability.In contrast with GSRM,LSRM only reduces the strength of local soil,while the strength of other soil remains unchanged.Therefore,deformation by LSRM is more reasonable than that by GSRM.In addition,the accuracy of the slope's deformation depends on the constitutive model to a large degree,and the variable-modulus elasto-plastic model was thus adopted.This constitutive model was an improvement of the Duncan–Chang model,which modified soil's deformation modulus according to stress level,and it thus better reflected the plastic feature of soil.Most importantly,the parameters of the variable-modulus elasto-plastic model could be determined through in-situ tests,and parameters determination by plate loading test and pressuremeter test were introduced.Therefore,it is easy to put this model into practice.Finally,LSRM and the variable-modulus elasto-plastic model were used to analyze Egongdai ancient landslide.Safety factor,deformation field,and optimal reinforcement measures for Egongdai ancient landslide were obtained based on the proposed method.

Self-assembled Nanohybrid from Opposite Charged Sheets:Alternate Stacking of CoAl LDH and MoS2

Hybrid materials are attracting intensive attention for their applications in electronics, photoelectronics, LEDs, field-effect transistors, etc. Engineering new hybrid materials and further exploiting their new functions will be significant for future science and technique development. In this work, alternatively stacked self-assembled CoAl LDH/MoS2 nanohybrid has been successfully synthesized by an exfoliation-flocculation method from positively charged CoAl LDH nanosheets（CoAl-NS） with negatively charged MoS2 nanosheets（MoS2-NS）. The CoAl LDH/MoS2 hybrid material exhibits an enhanced catalytic performance for oxygen evolution reaction（OER） compared with original constituents of CoAl LDH nanosheets and MoS2 nanosheets. The enhanced OER catalytic performance of CoAl LDH/MoS2 is demonstrated to be due to the improved electron transfer, more exposed catalytic active sites, and accelerated oxygen evolution reaction kinetics.

Test method and experimental research on resistance of oil shale under high temperature

Heating the oil shale by current underground to accomplish in-situ transformation process, is a viable direction. The electrical properties of oil shale under different temperatures, especially the resistance, become important. Charging oil shale underground to heat oil shale till kerogen's decomposition temperature, then crude oil and other gases can be generated. The resistance of the oil shale samples was measured by Direct Current (DC) quadripole method to find out the variation rules of resistance value. In the experiments, oil shale presented its semiconductor property. When heated till 350℃-450℃, its resistance changed greatly, optional for heating and cracking. The porosity, oil content, media and composition affected the resistance largely.

A colloidal crystal double-heterostructure fabricated with the angle controlled inclined deposition method

A self-assembly method, named the angle controlled inclined deposition method, is developed for fabricating well- ordered silica and polystyrene colloidal crystals. A high-quality colloidal crystal with a flat and uniform surface over a large area can be produced rapidly using a minute quantity of suspension and without any additional equipment. By controlling the inclined angle, we can fabricate colloidal crystals with diverse numbers of layers. A colloidal crystal double-heterostructure （composed of three different colloidal photonic crystals） can be rapidly fabricated with this method. Both experimental and simulation results show that the photonic band gap of the double-heterostructure is not a simple superposition of that of the compositional colloidal crystals along the stacking direction.

Fluorescence spectra of colloidal self-assembled CdSe nano-wire on substrate of porous Al2O3/Au nanoparticles

We present a self-assembly method to prepare array nano-wires of colloidal CdSe quantum dots on a substrate of porous Al2 O3 film modified by gold nanoparticles. The photoluminescence(PL) spectra of nanowires are in situ measured by using a scanning near-field optical microscopy(SNOM) probe tip with 100-nm aperture on the scanning near-field optical microscope. The results show that the binding sites from the edge of porous Al2 O3 nanopores are combined with the carboxyl of CdSe quantum dots’ surface to form an array of CdSe nanowires in the process of losing background solvent because of the gold nanoparticles filling the nano-holes of porous Al2 O3 film. Compared with the area of nonself-assembled nano-wire, the fluorescence on the Al2 O3/Au/CdSe interface is significantly enhanced in the self-assembly nano-wire regions due to the electron transfer conductor effect of the gold nanoparticles’ surface. In addition, its full width at half maximum(FWHM) is also obviously widened. The method of enhancing fluorescence and energy transfer can widely be applied to photodetector, photocatalysis, optical display, optical sensing, and biomedical imaging, and so on.

Applied research of correspondence analysis method in waste tailings reservoir heavy metal pollution monitoring points optimization

In order to optimize monitoring points and monitoring factor, the relationshipbetween pollutants and soil sample were established by correspondence analysis.Thestudy results show that the reflecting monitoring points and monitoring factors in thegraphic on the same factor axis can clearly express the intrinsic link between pollutantsand monitoring points and distribution characteristics.To determine the main monitoringpoint and the main monitoring indicators can reduce and optimize the number of monitoringpoints under the premise of ensuring the typical and representative of monitoring data.Using the correlation of pollutants can reduce the number of monitoring indicators and improvethe effectiveness of data collection.