In-situ investigation of atmospheric corrosion behavior of bronze under thin electrolyte layers using electrochemical technique

The atmospheric corrosion behavior of bronze under thin electrolyte layer （TEL） with different thicknesses was monitored using cathodic polarization curves, open circuit potential （OCP） and electrochemical impedance spectroscopy （EIS）. Cathodic polarization result indicates that the cathodic limiting current density increases with decreasing the TEL thickness. EIS result shows that the corrosion rate increases with decreasing the TEL thickness at the initial stage because the corrosion is dominated by the cathodic process, whereas after long immersion time, the corrosion degree with the TEL thickness is in the sequence of 150 μm 〉 310 μm〉 10μm ≈ bulk solution 〉 57 μm. The measurements of OCP and EIS present in-situ electrochemical corrosion information and their results are in good agreement with that of physical characterizations.

Limit equilibrium method(LEM) of slope stability and calculation of comprehensive factor of safety with double strength-reduction technique

When the slope is in critical limit equilibrium(LE) state, the strength parameters have different contribution to each other on maintaining slope stability. That is to say that the strength parameters are not simultaneously reduced. Hence, the LE stress method is established to analyze the slope stability by employing the double strengthreduction(DSR) technique in this work. For calculation model of slope stability under the DSR technique, the general nonlinear Mohr–Coulomb(M–C) criterion is used to describe the shear failure of slope. Meanwhile, the average and polar diameter methods via the DSR technique are both adopted to calculate the comprehensive factor of safety(FOS) of slope. To extend the application of the polar diameter method, the original method is improved in the proposed method. After comparison and analysis on some slope examples, the proposed method's feasibility is verified. Thereafter, the stability charts of slope suitable for engineering application are drawn. Moreover, the studies show that:(1) the average method yields similar results as that of the polardiameter method;(2) compared with the traditional uniform strength-reduction(USR) technique, the slope stability obtained using the DSR techniquetends to be more unsafe; and(3) for a slope in the critical LE state, the strength parameter φ, i.e., internal friction angle, has greater contribution on the slope stability than the strength parameters c, i.e., cohesion.

In-situ/operando characterization techniques in lithium-ion batteries and beyond

Nowadays,in-situ/operando characterization becomes one of the most powerful as well as available means to monitor intricate reactions and investigate energy-storage mechanisms within advanced batteries.The new applications and novel devices constructed in recent years are necessary to be reviewed for inspiring subsequent studies.Hence,we summarize the progress of in-situ/operando techniques employed in rechargeable batteries.The members of this large family are divided into three sections for introduction,including bulk material,electrolyte/electrode interface and gas evolution.In each part,various energy-storage systems are mentioned and the related experimental details as well as data analysis are discussed.The simultaneous strategies of various in-situ methods are highlighted as well.Finally,current challenges and potential solutions are concluded towards the rising influence and enlarged appliance of in-situ/operando techniques in the battery research.

In-situ/operando techniques to identify active sites for thermochemical conversion of CO_(2) over heterogeneous catalysts

The catalytic conversion of CO_(2) to fuels or chemicals is considered to be an effective pathway to mitigate the greenhouse effect. To develop new types of efficient and durable catalysts, it is critical to identify the catalytic active sites, surface intermediates, and reaction mechanisms to reveal the relationship between the active sites and catalytic performance. However, the structure of a heterogeneous catalyst usually dynamically changes during reaction, bringing a great challenge for the identification of catalytic active sites and reaction pathways. Therefore, in-situ/operando techniques have been employed to real-time monitor the dynamic evolution of the structure of active sites under actual reaction conditions to precisely build the structure–function relationship. Here, we review the recent progress in the application of various in-situ/operando techniques in identifying active sites for catalytic conversion of CO_(2) over heterogeneous catalysts. We systematically summarize the applications of various optical and X-ray spectroscopy techniques, including Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and X-ray absorption spectroscopy (XAS), in identifying active sites and determining reaction mechanisms of the CO_(2) thermochemical conversion with hydrogen and light alkanes over heterogeneous catalysts. Finally, we discuss challenges and opportunities for the development of in-situ characterization in the future to further enlarge the capability of these powerful techniques.

Dynamic phase transition behavior of a LiMn_(0.5)Fe_(0.5)PO_(4) olivine cathode material for lithium-ion batteries revealed through in-situ X-ray techniques

LiMn_(0.5)Fe_(0.5)PO_(4) has attracted great interest due to its good electrochemical performance and higher operating voltages.This has led to a greater than 30 percent higher energy density than for commercial Li Fe PO4 olivine cathodes.Understanding the phase transition behaviors and kinetics of this material will help researchers to design and develop next generation cathodes for Li-ion batteries.In this study,we investigated non-equilibrium phase transition behaviors in a LiMn_(0.5)Fe_(0.5)PO_(4) cathode material during charge–discharge processes by varying current rates(C-rates)using synchrotron in-situ X-ray techniques.These methods included wide angle X-ray scattering(in-situ WAXS)and X-ray absorption spectroscopy(in-situ XAS).The WAXS spectra indicate that the phase transition of LiMn_(0.5)Fe_(0.5)PO_(4) material at slow C-rates is induced by a two-phase reaction.In contrast,at a high C-rate(5 C),the formation of an intermediate phase upon discharge is clearly observed.Concurrently,the oxidation numbers of the redox reactions of Fe^(2+)/Fe^(3+)and Mn^(2+)/Mn^(3+)were evaluated using in-situ XAS.This combination of synchrotron in-situ X-ray techniques gives clear insights into the non-equilibrium phase transition behavior of a LiMn_(0.5)Fe_(0.5)PO_(4) cathode material.This new understanding will be useful for further developments of this highly promising cathode material for practical commercialization.

Techniques for in-situ stress measurement at great depth

Reliable information of in--situ stress state is necessary for the design andconstruction of most important rock projects. As most rock projects are getting deeper and deeper,traditional techniques of in--situ stress measurement are not very suitable. The current techniquesof in--situ stress measurement and their insufficiency for use at great depth are analyzed. Somebasic ideas of the development of new techniques and the improvement of current techniques for useat great depth are provided.

Effects of in-situ stress on the stability of a roadway excavated through a coal seam

Roadways excavated through a coal seam can exert an adverse effect on roadway stability. To investigate the effects of in-situ stress on roadway stability, numerical models were built and high horizontal stresses at varying orientations were applied. The results indicate that stress concentrations, roadway deformation and failure increase in magnitude and extent as the excavation angle with respect to the maximum horizontal stress increases. In addition, the stress adjacent to the coal-rock interface sharply varies in space and evolves with time; coal is much more vulnerable to deformation and failure than rock.The results provide insights into the layout of roadways excavated through a coal seam. Roadways should be designed parallel or at a narrow angle to the maximum horizontal stress. The concentrated stress at the top corner of the face-end should be reduced in advance, and the coal seam should be reinforced immediately after excavation.

Influences of rainfall infiltration on stability of accumulation slope by in-situ monitoring test

In order to improve the understanding of the fundamental mechanism of rainfall infiltration induced landslides in accumulation slope and to clarify some important characteristics of slope performance,artificial rainfall simulation tests and field synthetic monitoring were carried out on a typical accumulation slope of Shangrui Freeway in Guizhou Province,China.The monitoring results show that the most accumulation landslides caused by rainfall infiltration are shallow relaxation failure,whose deformation zone lies within the top 0-4 m soil layer.The deformation of slope gradually reduces from the surface,where the greatest deformation lies in,to the deep part of slope.The average percentage of infiltration during the first 2 h is 86%,and then it reduces gradually with time because of the increase of the surface runoff.The average percentage of infiltration drop to a relatively stable value(50%)after 6 h.Rainfall infiltration causes obvious increase of pore-water pressure,which may result in a reduction of shear strength due to a decrease in effective stress and wetting-induced softening.The double-effect of rainfall infiltration is the main reason of rainfall infiltration induced landslides in accumulation slope.

Harmonic balance method with alternating frequency/time domain technique for nonlinear dynamical system with fractional exponential

Comparisons of the common methods for obtaining the periodic responses show that the harmonic balance method with alternating frequency/time （HB-AFT） do- main technique has some advantages in dealing with nonlinear problems of fractional exponential models. By the HB-AFT method, a rigid rotor supported by ball bearings with nonlinearity of Hertz contact and ball passage vibrations is considered. With the aid of the Floquet theory, the movement characteristics of interval stability are deeply studied. Besides, a simple strategy to determine the monodromy matrix is proposed for the stability analysis.

A Review of In‑Situ Techniques for Probing Active Sites and Mechanisms of Electrocatalytic Oxygen Reduction Reactions

Electrocatalytic oxygen reduction reaction(ORR)is one of the most important reactions in electrochemical energy technologies such as fuel cells and metal–O2/air batteries,etc.However,the essential catalysts to overcome its slow reaction kinetic always undergo a complex dynamic evolution in the actual catalytic process,and the concomitant intermediates and catalytic products also occur continuous conversion and reconstruction.This makes them difficult to be accurately captured,making the identification of ORR active sites and the elucidation of ORR mechanisms difficult.Thus,it is necessary to use extensive in-situ characterization techniques to proceed the real-time monitoring of the catalyst structure and the evolution state of intermediates and products during ORR.This work reviews the major advances in the use of various in-situ techniques to characterize the catalytic processes of various catalysts.Specifically,the catalyst structure evolutions revealed directly by in-situ techniques are systematically summarized,such as phase,valence,electronic transfer,coordination,and spin states varies.In-situ revelation of intermediate adsorption/desorption behavior,and the real-time monitoring of the product nucleation,growth,and reconstruction evolution are equally emphasized in the discussion.Other interference factors,as well as in-situ signal assignment with the aid of theoretical calculations,are also covered.Finally,some major challenges and prospects of in-situ techniques for future catalysts research in the ORR process are proposed.

Synthesis, in-situ coating and characterization of scorodite with high leaching stability

To improve stability of scorodite,a method of simultaneous synthesis and in-situ coating of scorodite was proposed.Scorodite particles with polyhedral and raspberry-like morphologies were synthesized in an Fe(Ⅱ).As(Ⅴ).H2O system at 90℃and pH 1.5 by blowing oxygen gas into the system.When the initial Fe/As molar ratio exceeded 1:1,a coating of sulfate-containing iron(hydr)oxides formed on the surfaces of scorodite particles during synthesis.To evaluate the leaching stability of synthesized scorodite samples,toxicity characteristic leaching procedure(TCLP)tests were conducted at pH 4.93 for 60 h,and long-term leaching tests were conducted for 30.40 d within a pH range of 5.40.10.88.The leaching results indicated that the release of arsenic from scorodite was noticeably postponed by the coating,and the average arsenic concentrations in the leaching solutions were as low as 0.12 mg/L in the TCLP tests and lower than 0.5 mg/L in the long-term leaching tests.

Overview of Moving Particle Semi-implicit Techniques for Hydrodynamic Problems in Ocean Engineering

With the significant development of computer hardware,many advanced numerical techniques have been proposed to investigate complex hydrodynamic problems.This article aims to provide a detailed review of moving particle semi-implicit(MPS)techniques and their application in ocean and coastal engineering.The achievements of the MPS method in stability and accuracy,boundary conditions,and acceleration techniques are discussed.The applications of the MPS method,which are classified into two main categories,namely,multiphase flows and fluid-structure interactions,are introduced.Finally,the prospects and conclusions are highlighted.The MPS method has the potential to solve practical problems.

Molecular Reactivity and Interface Stability Modification in In-Situ Gel Electrolyte for High Performance Quasi-Solid-State Lithium Metal Batteries

Quasi-solid-state lithium metal battery is a promising candidate for next generation high energy density and high safety power supply.Despite intensive efforts on electrolytes,uncontrolled interfacial reactions on lithium with electrolyte and patchy interfacial contacts still hinder its practical process.Herein,we bring in rationally designed F contained groups into polymer skeleton via in-situ gelation for the first time to establish quasi-solid-state battery.This method achieves a capacity retention of 90%after 1000 cycles at 0.5C with LiFePO_(4)cathodes.The interface constructed by polymer skeleton and reaction with–CF_(3)lead to the predicted solid electrolyte interface species with high stability.Furthermore,we optimize molecular reactivity and interface stability with regulating F contained end groups in the polymer.Comparisons on different structures reveal that high performance solid stable lithium metal batteries rely on chemical modification as well as stable polymer skeleton,which is more critical to construct robust and steady SEI with uniform lithium deposition.New approach with functional groups regulation proposes a more stable cycling process with a capacity retention of 94.2%at 0.5C and 87.6%at 1C after 1000 cycles with LiFePO_(4) cathodes,providing new insights for the practical development of quasi-solid-state lithium metal battery.

A NEW TECHNIQUE IN BOUNDEDNESS OF INFINITE DELAY DIFFERENTIAL EQUATIONS

ＡＮＥＷＴＥＣＨＮＩＱＵＥＩＮＢＯＵＮＤＥＤＮＥＳＳＯＦＩＮＦＩＮＩＴＥＤＥＬＡＹＤＩＦＦＥＲＥＮＴＩＡＬＥＱＵＡＴＩＯＮＳ＊ＺｈａｎｇＳｈｕｎｉａｎ（张书年）（Ｄｅｐｔ．ｏｆＡｐｐｌｉｅｄＭａｔｈｅｍａｔｉｃｓ，ＳｈａｎｇｈａｉＪｉａｏｔｏｎｇＵｎ...

The Vibrational Motion of a Dynamical System Using Homotopy Perturbation Technique

This paper outlines the vibrational motion of a nonlinear system with a spring of linear stiffness. Homotopy perturbation technique (HPT) is used to obtain the asymptotic solution of the governing equation of motion. The numerical solution of this equation is obtained using the fourth order Runge-Kutta method (RKM). The comparison between both solutions reveals high consistency between them which confirms that, the accuracy of the obtained solution using aforementioned perturbation technique. The time history of the attained solution is represented through some plots to reveal the good effect of the different parameters of the considered system on the motion at any instant. The conditions of the stability of the attained solution are presented and discussed.

PROGRESS OF ACOUSTIC WAVE TECHNIQUE ANDITS APPLICATION IN UNDERGROUND PRESSURE MEASUREMENT

This paper carries out tbe experirnent study on the correlation between am stress-strain process of rock samples and the acoustie parameter change of rock by using the measurement system of KS acoustic wave data processing device. On the spot, the stability of surrounding rock is studied by means of experiments on the relationship between the change process (from elastie to plastic failure zone) in surrounding rock of roadway and the change law of acoustic parameters of rock. These acoustie parameters inelude wave amplitude, spectral amplitude, spectrum area, spectral density,wave veloeity and attenuation coefficient etc.

Investigation on Thermal and Dimensional Stability of Epoxy Resin In-Situ Modified by Cyanate Ester Resin and Polydimethylsiloxane

The thermal and dimensional stability of epoxy resin(EP)in-situ modified by cyanate ester(CE)and polydimethylsiloxane(PDMS)are investigated by means of experiments and numerical simulation.Thermal gravimetric analysis(TGA)and differential scanning calorimeter(DSC)are used to analyze the heat resistance of the modified EP.The dimensional stability is characterized by the volume shrinkage of the series PDMS/CE/EP obtained by the density method.The chemical structure of the PDMS/CE/EP is analyzed by Fourier transform infrared spectroscopy(FTIR).The results of TGA and DSC indicate that the thermal stability of PDMS/CE/EP decreases firstly and then increases with the increase in the amount of CE.The addition of PDMS shows a slight effect on the thermal stability.The 40%CE makes the blending system exhibit the lowest initial decomposition temperature,which reduces by 15.5%and 40.8%compared with pure EP and CE,respectively.The FTIR results suggested that the influence of CE on the thermal stability of the modified EP is mainly ascribed to the generation of oxazolidinone ring with low thermal stability and the increase in the triazine ring with high thermal stability.The volume shrinkage measurement results show that the introduction of CE and PDMS are both beneficial to the improvement of the dimensional stability of the blending systems.The in-situ addition of 80%CE shows the lowest volume shrinkage of6.11%.The thermal stress distribution of PDMS/CE/EP generated during the solidification process is simulated by the finite element analysis.The results suggested that the introduction of 80%CE into EP results in the lowest thermal stress in the blending system,which indicates that the system has the lowest volume shrinkage,which agrees well with the experimental results.

Nonlinear Robust Stabilization of Ship Roll by Convex Optimization

Dear Editor,This letter presents a nonlinear robust controller design method for ship roll stabilization by combining the dual of Lyapunov's stability theorem with the sum of squares(SOS) technique. Varying initial metacentric height and ship speed are regarded as uncertainties, sea waves are considered as external disturbances, and then the robust nonlinear controller is designed. Taking a container ship as an example, simulations are performed to verify the effectiveness of the proposed design scheme.

In-situ regeneration of Bi^(0) active site to renew surface activation for long-term stable and efficient CO_(2)-to-formate electrosynthesis

CO_(2)-to-formate electrosynthesis with high selectivity and stability has been a long-sought objective.Unfortunately,most catalysts undergo structural and valence state changes due to surface oxidation during operation or storage,resulting in decreased catalytic performance.Herein,we report a efficient and stable BiIn@Cu-foam electrode through the in-situ regeneration of Bi^(0) active sites to renew the surface activation.The electronic structure of Bi site can be regulated by introducing In,thereby enhancing the adsorption strength of*OCHO.The optimized electrode exhibits over 90%FE_(formate)at a wide potential window(-0.9–-2.2 V),and formation rate for 3.15 mM cm^(-1)h^(-1).Especially,the electrode can maintain the high performance at continuously electrolysis for more than 300 h,or for more than 50 cycles,even repeated operation and storage for more than 2 years.This work provides a promising candidate and new insight to construct industrially viable stable Bi-based catalyst for formate electrosynthesis.

Relaxed Stability Criteria for Time-Delay Systems:A Novel Quadratic Function Convex Approximation Approach

This paper develops a quadratic function convex approximation approach to deal with the negative definite problem of the quadratic function induced by stability analysis of linear systems with time-varying delays.By introducing two adjustable parameters and two free variables,a novel convex function greater than or equal to the quadratic function is constructed,regardless of the sign of the coefficient in the quadratic term.The developed lemma can also be degenerated into the existing quadratic function negative-determination(QFND)lemma and relaxed QFND lemma respectively,by setting two adjustable parameters and two free variables as some particular values.Moreover,for a linear system with time-varying delays,a relaxed stability criterion is established via our developed lemma,together with the quivalent reciprocal combination technique and the Bessel-Legendre inequality.As a result,the conservatism can be reduced via the proposed approach in the context of constructing Lyapunov-Krasovskii functionals for the stability analysis of linear time-varying delay systems.Finally,the superiority of our results is illustrated through three numerical examples.