In-situ polymerized PEO-based solid electrolytes contribute better Li metal batteries:Challenges,strategies,and perspectives

Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)with good electrochemical stability and excellent Li salt solubility are considered as one of the most promising SPEs for solid-state lithium metal batteries(SSLMBs).However,PEO-based SPEs suffer from low ionic conductivity at room temperature and high interfacial resistance with the electrodes due to poor interfacial contact,seriously hindering their practical applications.As an emerging technology,in-situ polymerization process has been widely used in PEO-based SPEs because it can effectively increase Li-ion transport at the interface and improve the interfacial contact between the electrolyte and electrodes.Herein,we review recent advances in design and fabrication of in-situ polymerized PEO-based SPEs to realize enhanced performance in LMBs.The merits and current challenges of various SPEs,as well as their stabilizing strategies are presented.Furthermore,various in-situ polymerization methods(such as free radical polymerization,cationic polymerization,anionic polymerization)for the preparation of PEO-based SPEs are summarized.In addition,the application of in-situ polymerization technology in PEO-based SPEs for adjustment of the functional units and addition of different functional filler materials was systematically discussed to explore the design concepts,methods and working mechanisms.Finally,the challenges and future prospects of in-situ polymerized PEO-based SPEs for SSLMBs are also proposed.

Enhanced thermal and electrical properties of poly (D,L-lactide)/ multi-walled carbon nanotubes composites by in-situ polymerization

Biodegradable poly （D,L-lactide） （PLA）/carboxyl-functionalized multi-walled carbon nanotubes （c-MWCNTs） composites were achieved via in-situ polymerization. These as-prepared composite materials were characterized with FT-IR, XRD, TG, DSC, SEM, and high insulation resistance meter. The results demonstrate that the multi-walled carbon nanotube was carboxyl functionalized, which improved the collection between c-MWCNTs and PLA, and further realized the graft copolymerization of c-MWCNTs and PLA. There is a higher glass transition temperature and a lower pyrolysis temperature of PLA/c-MWCNTs composites than pure PLA. The c-MWCNTs gave a better dispersion than unmodified MWCNTs in the PLA matrix, and an even coating of PLA on the surface of c-MWCNTs was obtained, which increased the interfacial interaction. High insulation resistance analysis showed that the addition of c-MWCNTs increased the electric conductivity, and c-MWCNTs performed against the large dielectric coefficient and electrostatic state of PLA. These results demonstrated that c-MWCNTs modified PLA composites were beneficial for potential application in the development of heat-resisting and conductivity plastic engineering.

In-situ interfacial passivation and self-adaptability synergistically stabilizing all-solid-state lithium metal batteries

The function of solid electrolytes and the composition of solid electrolyte interphase(SEI)are highly significant for inhibiting the growth of Li dendrites.Herein,we report an in-situ interfacial passivation combined with self-adaptability strategy to reinforce Li_(0.33)La_(0.557)TiO_(3)(LLTO)-based solid-state batteries.Specifically,a functional SEI enriched with LiF/Li_(3)PO_(4) is formed by in-situ electrochemical conversion,which is greatly beneficial to improving interface compatibility and enhancing ion transport.While the polarized dielectric BaTiO_(3)-polyamic acid(BTO-PAA,BP)film greatly improves the Li-ion transport kinetics and homogenizes the Li deposition.As expected,the resulting electrolyte offers considerable ionic conductivity at room temperature(4.3 x 10~(-4)S cm^(-1))and appreciable electrochemical decomposition voltage(5.23 V)after electrochemical passivation.For Li-LiFePO_(4) batteries,it shows a high specific capacity of 153 mA h g^(-1)at 0.2C after 100 cycles and a long-term durability of 115 mA h g^(-1)at 1.0 C after 800 cycles.Additionally,a stable Li plating/stripping can be achieved for more than 900 h at 0.5 mA cm^(-2).The stabilization mechanisms are elucidated by ex-situ XRD,ex-situ XPS,and ex-situ FTIR techniques,and the corresponding results reveal that the interfacial passivation combined with polarization effect is an effective strategy for improving the electrochemical performance.The present study provides a deeper insight into the dynamic adjustment of electrode-electrolyte interfacial for solid-state lithium batteries.

Analyses of non-aqueous reactive polymer insulation layer in high geothermal tunnel

The scenario of geothermal tunnel is commonly observed around the world,and increases with the new constructions in the long and deep tunnels,for example in China.Tunnel insulation is generally divided into active and passive insulation.In passive insulation,it is an effective way to set low thermal con-ductivity materials as the thermal insulation layer as the choice of insulation material mainly depends on the thermal conductivity.Polymer is a kind of material with good geothermal performance,but there are relatively few studies.In this context,the transient plane source(TPS)method was used to measure the thermal conductivity of the developed polymer.Then,the temperature field of the high geothermal tunnel insulated by the non-aqueous reactive polymer layer was simulated.With the parametric analysis results,the suggestions for the tunnel layers were proposed accordingly.It revealed that the thermal conductivity of polymer first increases and then decreases with temperature.There are two rising sec-tions(?40e10?C and 20e90?C),one flat section(10e20?C)and one descending section(>90?C).It is observed the thermal conductivity of polymer increases with increase of the density of insulation layer and the density,and the thermal conductivity decreases when exposed to high temperatures.The temperature of the surrounding rocks increases with increase of the thermal conductivity and the thickness of polymer.Finally,a more economical thickness(5 cm)was proposed.Based on the parametric study,a thermal insulation layer with thermal conductivity less than 0.045 W/(m K),thickness of 5 cm and a density less than 0.12 g/cm 3 is suggested for practice.

Regulatable Orthotropic 3D Hybrid Continuous Carbon Networks for Efficient Bi-Directional Thermal Conduction

Vertically oriented carbon structures constructed from low-dimen-sional carbon materials are ideal frameworks for high-performance thermal inter-face materials(TIMs).However,improving the interfacial heat-transfer efficiency of vertically oriented carbon structures is a challenging task.Herein,an orthotropic three-dimensional(3D)hybrid carbon network(VSCG)is fabricated by depositing vertically aligned carbon nanotubes(VACNTs)on the surface of a horizontally oriented graphene film(HOGF).The interfacial interaction between the VACNTs and HOGF is then optimized through an annealing strategy.After regulating the orientation structure of the VACNTs and filling the VSCG with polydimethylsi-loxane(PDMS),VSCG/PDMS composites with excellent 3D thermal conductive properties are obtained.The highest in-plane and through-plane thermal conduc-tivities of the composites are 113.61 and 24.37 W m^(-1)K^(-1),respectively.The high contact area of HOGF and good compressibility of VACNTs imbue the VSCG/PDMS composite with low thermal resistance.In addition,the interfacial heat-transfer efficiency of VSCG/PDMS composite in the TIM performance was improved by 71.3%compared to that of a state-of-the-art thermal pad.This new structural design can potentially realize high-performance TIMs that meet the need for high thermal conductivity and low contact thermal resistance in interfacial heat-transfer processes.

Thermal Emulsion Polymerization without any Conventional Initiators and Emulsifiers

Stable poly（styrene-co-sodium styrene sulfonate） （P（St-NaSS） nanoparticles with broader size distribution were synthesized by thermal emulsion polymerization without any conventional initiators and emulsifiers. The obtained polymer nanoparticles have higher potential, and the particle sizes have broad distribution. The stability of polymer particles originated from the addition of small amounts of ionic comonomer, NaSS, which can act as an emulsifier in somewhat. The monomer conversion could reach up to about 28 wt% in 48 h, and did not increase by further polymerization when higher polymerization temperature （120℃） was employed. This polymerization system may be give some further understand for mechanism of emulsion polymerization.

SYNTHESIS AND CHARACTERIZATION OF POLYPROPYLENE/MONTMORILLONITE NANOCOMPOSITES VIA AN in-situ POLYMERIZATION APPROACH

Polypropylene/montmorillonite (PP/MMT)nanocomposites were prepared by in-situ polymerization using aMMT/MgCl_2/TiCl_4-EB Ziegler-Natta catalyst activated by triethylaluminum(TEA). The enlarged layer spacing of MMT wasconfirmed by X-ray wide angle diffraction (WAXD), demonstrating that MMT were intercalated by the catalyst components.X-ray photoelectron spectrometry (XPS) analysis proved that TiCl_4 was mainly supported on MgCl_2 instead of on the surfaceof MMT The exfoliated structure of MMT layers in the PP matrix of PP/MMT composites was demonstrated by WAXDpatterns and transmission electron microscopy (TEM) observation. The higher glass transition temperature and higher storage modulus of the PP/MMT composites in comparison with pure PP were revealed by dynamic mechanical analysis (DMA).

Preparation of Polysulfonamide/ZnO Nanocomposite by In-Situ Polymerization

Polysulfonamide/zinc oxide(PSA/ZnO) nanocomposite films with w(ZnO)=0.5% were prepared by in-situ polymerization based on 4,4′-diaminodiphenylsulfone and terephthaloyl chloride in the common solvent N,N-Dimethylacetamide(DMAc). Atomic force microscopy (AFM) was employed to observe the microstructure of the composite film. The thermal property was investigated by TGA and mechanical property was characterized by DXLL-1000 electromechanical material testing machine. The results showed that the breaking strength of the film containing 0.5% ZnO was great enhanced. The average size of ZnO particles was below 100 nm. The introduction of ZnO as nano filler in PSA react as UV shield effect and make the composite mechanical property improved.

Non-Thermal Radio Frequency Stimulation of Tubulin Polymerization in Vitro: A Potential Therapy for Cancer Treatment

The use of radio frequency energy is an established technology for certain oncology therapies. Direct inputs of radio frequency (RF) energy as thermal energy are applied to ablate tumors or catalyze secondary reactions in adjunct treatments against certain tumor types. Yet, other applications are being developed which take advantage of properties of RFs that impinge on biological proteins and cells without thermal effects. Here we report a proof-of-concept application of specific, digitally encoded, low power (non-thermal) radio frequency energy in an in vitro preparation of a tubulin polymerization assay. The radio frequency energy signal, designated M2(3), was applied to the tubulin polymerization assay samples during spectrophotometric measurements to assess the effectiveness for enhancing tubulin polymerization. A commercially available taxane (paclitaxel) that promotes tubulin polymerization was used as a control to assess the effectiveness of the M2(3) radio frequency energy signal on tubulin polymerization rates. A low power, specific, digital radio frequency energy signal is capable of promoting tubulin polymerization as effectively as a commercially available taxane.

Nano-Li3V2（PO4）3/C Synthesized by Thermal Polymerization Method as Cathode Material for Lithium Ion Batteries

A nano-Li3V2（PO4）3/C powder was successfully prepared by a thermal polymerization method. The particle sizes of the intermediate product powder and the final product Li3V2（PO4）3 are all less than 200 nm. The carbon is partially coated on the surface of Li3V2（PO4）3 particles and the rest exists between particles with a total carbon content of 4.6wt%. This nano-Li3V2（PO4）3/C sample shows a discharge capacity of 124 mAh/g with-out capacity fading after 100 cycles at 0.1 C in the voltage rang of 3.0-4.3 V. Excellent rate performance is also achieved with a capacity of 80 mAh/g at 20 C in 3.0-4.3 V and 100 mAh/g at 10 C in 3.0-4.8 V. This study suggests that the thermal polymerization method is suitable to synthesize nano-Li3V2（PO4）3/C materials.

CHANGES OF STRUCTURE AND PROPERTIES OF POLY (ETHYLENE TEREPHTHALATE) CAUSED BY IN-SITU POLYMERIZATION OF PYRROLE

Conductive polymer composites based on crystalline polymer matrix have been prepared by using an in-situ polymerization process of pyrrole in amorphous poly （ethylene terephthalate） （PET） film. The DSC and WAXD measurement and SEM observation show that liquid-induced crystallization of PET matrix has occurred during the preparation of composite films. Depending upon the equilibrium degree of swelling and crystallinity, the limited depth of penetration of pyrrole molecules results in a skin-core structure of the composite film. The skin layer containing charge transfer intercalated polypyrrole has a surface resistance of 3.5×10;Ω. Rigid and heat-resistant polypyrrole molecules formed in PET film increase the tensile modulus and, especially, the rigidity of PET at elevated temperatures. However, they decrease the tensile strength and elongation at break, and impair the thermal ductility of PET.

PREPARATION OF POLYSULFONAMIDE AND MODIFIED TITANIUM OXIDE NANOCOMPOSITES BY IN-SITU POLYMERIZATION

A kind of new nano composite with ultraviolet （UV） ray resistance and high temperature stability was prepared by in-situ polymerization in low temperature. Polysulfonamide （PSA） was synthesized with 4, 4＇-diaminodiphenyl sulfone （DDS） and terephthaloyl chloride （TPC） in the common solvent N, N-Dimethyl- -acetamide （DMAc）. Nano filler is a certain nano titanium oxide modified by silicon oxide （TMS）, which plays the role of UV resistance additives. Properties of the novel composite materials were characterized by Atomic Force microscopy （AFM）, thermal gravimetric Analysis （TGA） and Ultraviolet Spectroscopy. AFM had showed the sizes and distributions of TMS particles in the nanocomposite. Ultraviolet Spectroscopy for the nanocomposites showed a large absorption in UV band. TGA showed the decomposition temperature was increased over ten degrees with 0.5% wt TMS for this nanocomposite compared with pure PSA.

Breaking Through Bottlenecks for Thermally Conductive Polymer Composites:A Perspective for Intrinsic Thermal Conductivity,Interfacial Thermal Resistance and Theoretics

Rapid development of energy,electrical and electronic technologies has put forward higher requirements for the thermal conductivities of polymers and their composites.However,the thermal conductivity coefficient(λ)values of prepared thermally conductive polymer composites are still difficult to achieve expectations,which has become the bottleneck in the fields of thermally conductive polymer composites.Aimed at that,based on the accumulation of the previous research works by related researchers and our research group,this paper proposes three possible directions for breaking through the bottlenecks:(1)preparing and synthesizing intrinsically thermally conductive polymers,(2)reducing the interfacial thermal resistance in thermally conductive polymer composites,and(3)establishing suitable thermal conduction models and studying inner thermal conduction mechanism to guide experimental optimization.Also,the future development trends of the three above-mentioned directions are foreseen,hoping to provide certain basis and guidance for the preparation,researches and development of thermally conductive polymers and their composites.

Thermal conductivity model of filled polymer composites

Theoretical and empirical models for predicting the thermal conductivity of polymer composites were summarized since the 1920s.The effects of particle shape,filler amount,dispersion state of fillers,and interfacial thermal barrier on the thermal conductivity of filled polymer composites were investigated,and the agreement of experimental data with theoretical models in literatures was discussed.Silica with high thermal conductivity was chosen to mix with polyvinyl-acetate （EVA） copolymer to prepare SiO2/EVA co-films.Experimental data of the co-films＇ thermal conductivity were compared with some classical theoretical and empirical models.The results show that Agari＇s model,the mixed model,and the percolation model can predict well the thermal conductivity of SiO2/EVA co-films.

Relationship between polymerization degree and cementitious activity of iron ore tailings

The aim of this study is to understand the relationship between the polymerization degree and cememitious activity of iron ore tailings. In light of the poor usage of iron ore tailings, stockpile samples from Tangshan were studied in terms of their ability to become cementitious materials. Compound thermal activation was used to improve the cementitious properties of the tailings, while analyzing methods, such as X-ray diffraction （XRD）, infrared spectroscopy （IR）, nuclear magnetic resonance （NMR）, and X-ray photoelectron spectrometer （XPS）, were employed to study the changes in phase and structure under different activation conditions. The results reveal clear relationships between the binding energies of Si2p and O 1 s, polymerization degree, and cementitious activity of iron ore tailings.

Thermal and saline tolerance of Antarctic krill Euphausia superba under controlled in-situ aquarium conditions

As a key species of the Southern Ocean ecosystem,the thermal and saline tolerances of Antarctic krill(Euphausia superb a Dana)are relatively unknown because of the challenging environment and complicated situations needed for observation have inhibited in-situ experiments in the field.Hence,the thermal and saline tolerance of krill were examined under in-situ aquarium conditions with different controlled scenarios.According to the experiments,the critical lethal times of krill were 24h,2h and 0.5h under 9℃,12℃,and 15℃,respectively,and the estimated 50%lethal times were about 17.1 h and 1.7 h under 12℃and 15℃,respectively.Additionally,the critical lethal times(the estimated 50%lethal times)of krill were approximately 14h and 0.5h(about 22.9 h and 1.7 h)of salinity under 19.7 and 15.9,respectively.The observed critical and 50%lethal times of krill were 0.5 h and approximately 1.4 h,respectively,salinity under 55.2.The critical and 50%lethal temperatures of krill were 13℃and approximately 14.2℃,respectively.Additionally,the critical and 50%lethal salinity was 19.6 and approximately 17.5 for the lower saline(below normal oceanic salinity[34.4])environment and 50.3 and approximately 53.2 for the higher saline(above 34.4)environment,respectively.The upper thermal and saline preferences of krill can be considered 6℃and 26.8 to 41.2,respectively.These results can provide potential scenarios for predicting the possible fate of this key species in the Southern Ocean.

Highly Thermally Conductive Polymer/Graphene Composites with Rapid Room‑Temperature Self‑Healing Capacity

Composites that can rapidly self-healing their structure and function at room temperature have broad application prospects.However,in view of the complexity of composite structure and composition,its self-heal is facing challenges.In this article,supramolecular effect is proposed to repair the multistage structure,mechanical and thermal properties of composite materials.A stiff and tough supramolecular frameworks of 2-[[(butylamino)carbonyl]oxy]ethyl ester(PBA)–polydimethylsiloxane(PDMS)were established using a chain extender with double amide bonds in a side chain to extend prepolymers through copolymerization.Then,by introducing the copolymer into a folded graphene film(FGf),a highly thermally conductive composite of PBA–PDMS/FGf with self-healing capacity was fabricated.The ratio of crosslinking and hydrogen bonding was optimized to ensure that PBA–PDMS could completely self-heal at room temperature in 10 min.Additionally,PBA–PDMS/FGf exhibits a high tensile strength of 2.23±0.15 MPa at break and high thermal conductivity of 13±0.2 W m^(−1)K^(−1);of which the self-healing efficiencies were 100%and 98.65%at room temperature for tensile strength and thermal conductivity,respectively.The excellent self-healing performance comes from the efficient supramolecular interaction between polymer molecules,as well as polymer molecule and graphene.This kind of thermal conductive self-healing composite has important application prospects in the heat dissipation field of next generation electronic devices in the future.

Hydrothermal Synthesis and Crystal Structure of a New Three-dimensional Heterometallic Coordination Polymer

A new 3d-4fheterometallic polymer {[Sm2Cu（PDC）2（SO4）2（H20）6]·2H2O}n 1 has been synthesized by Sm2O3, Cu（SO4）2·5H2O and pyridine-3,5-dicarboxylic acid under hydrothermal conditions. The compound crystallizes in triclinic system, space group Pi, with a = 6.352（7）, b = 10.040（10）, c = 10.315（11） A, α = 94.958（14）, β = 95.556（7）, γ = 99.747（14）°, V = 641.7（12）A3, Z = 1, M, = 1030.63, Dc= 2.651 Mg/m3,μ = 5.615 mm-1, F（000） = 491, the final R = 0.0491 and wR = 0.1345 for 2098 observed reflections with I 〉 2σ（I）. The compound is a three-dimensional network structure in which infinite lanthanide-carboxylate chains are linked by [Cu（$04）2]2- metalloligands to form a mixed-metal coordination network.

Empirical correction of kinetic model for polymer thermal reaction process based on first order reaction kinetics

Based on the theory of first-order reaction kinetics,a thermal reaction kinetic model in integral form has been derive.To make the model more applicable,the effects of time and the conversion degree on the reaction rate parameters were considered.Two types of undetermined functions were used to compensate for the intrinsic variation of the reaction rate,and two types of correction methods are provided.The model was explained and verified using published experimental data of different polymer thermal reaction systems,and its effectiveness and wide adaptability were confirmed.For the given kinetic model,only one parameter needs to be determined.The proposed empirical model is expected to be used in the numerical simulation of polymer thermal reaction process.

Morphology and conductivity of in-situ PEO-LiClO_4-TiO_2 composite polymer electrolyte

PEO-LiClO4-TiO2 composite polymer electrolyte films were prepared. TiO2 was formed directly in matrix by hydrolysis and condensation reaction of tetrabutyl titanate. The crystallinity, morphology and ionic conductivity of composite polymer electrolyte films were examined by differential scanning calorimetry, scanning electron microscopy, atom force microscopy and alternating current impedance spectroscopy, respectively. The glass transition temperature and the crystallinity of composite polymer electrolytes are decreased compared with those of PEO-LiClO4 polymer electrolyte film. The results show that TiO2 particles are uniformly dispersed in PEO-LiClO4-5%TiO2 composite polymer electrolyte film. The maximal conductivity of 5.5×10、5 Scm at 20 ℃ of PEO-LiClO4-TiO2 film is obtained at 5% mass fraction of TiO2.