Extrapolation of upwelling irradiance just beneath the ocean surface from the in-water radiometric profile measurements

Accurate measurements of upwelling irradiance just beneath the ocean surface,E_(u)(λ,0^(-)),can be used to calculate ocean optical parameters,and further develop retrieval algorithms for remotely sensing water component concentrations.Due to the effects of sea surface waves,perturbation from instrument platform(ship),and instrument self-shading,E_(u)(λ,0^(-))is often difficult to be accurately measured.This study presents a procedure for extrapolating the E_(u)(λ,0^(-))from the in-water radiometric profile measurements.Using the optical profile data from 13 bands(ranging from 381 to 779 nm)measured by 45 casts in the Ligurian Sea during 2003–2009,the E_(u)(λ,0^(-))was extrapolated from in-water upwelling irradiance measurements between the initial shallow depth,Z_(0),and an optimal bottom depth,Z_(1),by three linear models(linear,2-degree polynomial,and exponential)and two nonlinear models(LOESS and spline).The accumulated errors of extrapolated E_(u)(λ,0^(-))at each wavelength for the five models were calculated.It was found that the optimal Z_(1) depth for the linear and exponential models was at the depth of80%of E_(u)(λ,Z_(0)),50%of E_(u)(λ,Z_(0))for the 2-degree polynomial model,40%of E_(u)(λ,Z_(0))for the LOESS model,and 15%of E_(u)(λ,Z_(0))for the spline model.The extrapolated E_(u)(λ,0^(-))derived from the five models was in good agreement with the calculated true E_(u)(λ,0^(-)).In all bands,the 2-degree polynomial model achieved the highest accuracy,followed by the LOESS model.In the short band of 381–559 nm,the linear and exponential models had the third-best performance,and the spline model performed worst within this range.For the red band of 619–779 nm,the accuracies of the exponential and spline models had the third highest performance,and the linear model produced lowest accuracy.Hence,the 2-degree polynomial model was an optimal procedure for extrapolation of E_(u)(λ,0^(-))from the in-water radiometric profile measurements.

Influence of pier height on the safety of trains running on high-speed railway bridges during earthquakes

Sudden earthquakes pose a threat to the running safety of trains on high-speed railway bridges,and the stiffness of piers is one of the factors affecting the dynamic response of train-track-bridge system.In this paper,a experiment of a train running on a high-speed railway bridge is performed based on a dynamic experiment system,and the corresponding numerical model is established.The reliability of the numerical model is verified by experiments.Then,the experiment and numerical data are analyzed to reveal the pier height effects on the running safety of trains on bridges.The results show that when the pier height changes,the frequency of the bridge below the 30 m pier height changes greater;the increase of pier height causes the transverse fundamental frequency of the bridge close to that of the train,and the shaking angle and lateral displacement of the train are the largest for bridge with 50 m pier,which increases the risk of derailment;with the pier height increases from 8 m to 50 m,the derailment coefficient obtained by numerical simulations increases by 75% on average,and the spectral intensity obtained by experiments increases by 120% on average,two indicators exhibit logarithmic variation.

Reliability-based life-cycle cost seismic design optimization of coastal bridge piers with nonuniform corrosion using different materials

Reinforcement corrosion is the main cause of performance deterioration of reinforced concrete(RC)structures.Limited research has been performed to investigate the life-cycle cost(LCC)of coastal bridge piers with nonuniform corrosion using different materials.In this study,a reliability-based design optimization(RBDO)procedure is improved for the design of coastal bridge piers using six groups of commonly used materials,i.e.,normal performance concrete(NPC)with black steel(BS)rebar,high strength steel(HSS)rebar,epoxy coated(EC)rebar,and stainless steel(SS)rebar(named NPC-BS,NPC-HSS,NPC-EC,and NPC-SS,respectively),NPC with BS with silane soakage on the pier surface(named NPC-Silane),and high-performance concrete(HPC)with BS rebar(named HPC-BS).First,the RBDO procedure is improved for the design optimization of coastal bridge piers,and a bridge is selected to illustrate the procedure.Then,reliability analysis of the pier designed with each group of materials is carried out to obtain the time-dependent reliability in terms of the ultimate and serviceability performances.Next,the repair time of the pier is predicted based on the time-dependent reliability indices.Finally,the time-dependent LCCs for the pier are obtained for the selection of the optimal design.

Experimental investigation and flow analysis of clear-water scour around pier and abutment in proximity

Local scour around bridge piers and abutments is one of the most significant causes of bridge failure.Despite a plethora of studies on scour around individual bridge piers or abutments,few studies have focused on the joint impact of a pier and an abutment in proximity to one another on scour.This study conducted laboratory experiments and flow analyses to examine the interaction of piers and abutments and their effect on clear-water scour.The experiments were conducted in a rectangular laboratory flume.They included 18 main tests(with a combination of different types of piers and abutments)and five control tests(with individual piers or abutments).Three pier types(a rectangular pier with a rounded edge,a group of three cylindrical piers,and a single cylindrical pier)and two abutment types(a wingewall abutment and a semicircular abutment)were used.An acoustic Doppler velocimeter was used to measure the three-dimensional flow velocity for analyses of streamline,velocity magnitude,vertical velocity,and bed shear stress.The results showed that the velocity near the pier and abutment increased by up to 80%.The maximum scour depth around the abutment increased by up to 19%.In contrast,the maximum scour depth around the pier increased significantly by up to l71%.The presence of the pier in the vicinity of the abutment led to an increase in the scour hole volume by up to 87%relative to the case with a solitary abutment.Empirical equations were also derived to accurately estimate the maximum scour depth at the pier adjacent to the abutment.

Experimental and numerical study on cyclic behavior of a UHPC-RC composite pier

Conventional reinforced concrete piers are vulnerable to severe compressive damage under strong earthquake conditions and are difficult to quickly rehabilitate.This paper develops a new type of composite pier,consisting of ultra-high-performance concrete(UHPC)and reinforced concrete(RC).This UHPC-RC composite pier uses a UHPC cover outside of an RC core to achieve a high load-carrying capacity and mitigate compressive damage.An experiment is performed to evaluate the performance of the UHPC-RC composite pier under cyclic deformation.The crack development,ultimate failure modes,and load-carrying capacities of the pier are observed.Because of the extraordinary compressive strength of UHPC,the composite pier suffers little compressive damage under large lateral deformations.The composite pier fails as a result of fracturing of the reinforcement.A numerical model is developed to reproduce the cyclic behavior of the composite pier.On the basis of the verified numerical model,a parametric analysis is used to investigate the influence of the thickness of the UHPC cover and the axial load ratio.Finally,an approach is recommended for designing composite piers.

Regularity classification and corresponding analysis method requirements of horizontally curved bridges with unequal pier heights

The seismic behavior of horizontally curved bridges,particularly with unequal height piers,is more complicated than that of straight bridges due to their geometric properties.In this study,the seismic responses of several horizontally curved single-column-bent viaducts with various degrees of curvature and different pier heights have been investigated,employing three different analysis approaches:namely,modal pushover analysis,uniform load method,and nonlinear time history analysis.Considering the investigated bridge configurations and utilizing the most common regularity indices,the results indicate that viaducts with 45-degree and 90-degree deck subtended angles can be categorized as regular and moderately irregular,respectively,while the bridges with 180-degree deck subtended angle are found to be highly irregular.Furthermore,the viaducts whose pier heights are asymmetric may be considered as irregular for almost all ranges of the deck subtended angles.The effects of higher transverse and longitudinal modes are discussed and the minimum analysis requirements are identified to assess the seismic response of such bridge configurations for design purposes.Although the Regularity Indices used here are useful tools to distinguish between regular and irregular bridges,further studies are needed to improve their reliability.

Time-varying seismic fragility analysis of durability damage of high-tensile reinforcement ECC bridge pier

The deterioration of the performance of offshore bridges is particularly prominent due to the complex natural environment,including the coupling effects of earthquake and seawater erosion.In particular,bridge piers are the main energy-consuming and load-bearing components,so that excellent seismic capacity of bridge piers is the key to avoiding bridge damage.Although earthquake resistant behavior of ordinary reinforced concrete bridge piers(ordinary pier)can be improved by increasing the section size and reinforcement ratio of piers,the improvement of the earthquake resistant behavior is limited.To further improve the earthquake resistant behavior of bridge piers,high-tensile reinforcement engineered cementitious composite(ECC)bridge piers are utilized and time-varying seismic fragility analysis are conducted in this study.The refined model of a bridge pier is built by OpenSees.First,the influence of ECC replacement height on pier curvature is analyzed to determine the reasonable ECC height.Then,the time-varying fragility analysis of high-tensile reinforcement ECC piers(ECC composite piers)with durability damage are evaluated considering the time-varying law of materials.Four damage states,slight damage,moderate damage,extensive damage and complete collapse,are utilized in the study.These fragility curves indicate the durability damage can debase the earthquake resistant behavior of piers continually,the exceedance probability of the same state of destruction increases with the increase of peak ground acceleration(PGA)and service time of pier.The results also indicate that the corrosion level of chloride ion to pier is small during the early service period,and the bridge pier vulnerable curve is similar to that of the new bridge pier.As the level of chlorine ion corrosion deepens,transcendental probability is increased.Compared with the ordinary pier,the exceedance probability in each limit state of ECC composite piers is significantly reduced.The proposed ECC composite pies leads to better realistic time-varying earthquake resistant behavior.

ML and CFD Simulation of Flow Structure around Tandem Bridge Piers in Pressurized Flow

Various regions are becoming increasingly vulnerable to the increased frequency of floods due to the recent changes in climate and precipitation patterns throughout the world.As a result,specific infrastructures,notably bridges,would experience significant flooding for which they were not intended and would be submerged.The flow field and shear stress distribution around tandem bridge piers under pressurized flow conditions for various bridge deck widths are examined using a series of three-dimensional(3D)simulations.It is indicated that scenarios with a deck width to pier diameter(Ld/p)ratio of 3 experience the highest levels of turbulent disturbance.In addition,maximum velocity and shear stresses occur in cases with Ld/p equal to 6.Results indicate that increasing the number of piers from 1 to 2 and 3 results in the increase of bed shear stress by 24%and 20%respectively.Finally,five machine learning algorithms,including Decision Trees(DT),Feed Forward Neural Networks(FFNN),and three Ensemble models,are implemented to estimate the flow field and the turbulent structure.Results indicated that the highest accuracy for estimation of U,and W,were obtained using AdaBoost ensemble with R2=0.946 and 0.951,respectively.Besides,the Random Forest algorithm outperformed AdaBoost slightly in the estimation of V and turbulent kinetic energy(TKE)with R2=0.894 and 0.951,respectively.

Hysteretic behavior of post-tensioned precast segmental CFT double-column piers

Considering the desirable behavior of concrete filled steel tube(CFT)columns and the complicated behavior of segmental double-column piers under cyclic loads,three post-tensioned precast segmental CFT double-column pier specimens were tested to extend their application in moderate and high seismicity areas.The effects of the number of CFT segments and the steel endplates as energy dissipaters on the seismic behavior of the piers were evaluated.The experimental results show that the segmental piers exhibited stable hysteretic behavior with small residual displacements under cyclic loads.All the tested specimens achieved a drift ratio no less than 13%without significant damage and strength deterioration due to the desirable behavior of CFT columns.Since the deformation of segmental columns was mainly concentrated at the column-footing interfaces,the increase of the segment numbers for each column had no obvious effects on the loading capacity but reduced the initial stiffness of the specimens.The use of steel endplates improved the bearing capacity,stiffness and energy dissipation of segmental piers,but weakened their self-centering capacity.Fiber models were also proposed to simulate the hysteretic behavior of the tested specimens,and the influences of segment numbers and prestress levels on seismic behavior were further studied.

Numerical Simulation of the Influence of Water Flow on the Piers of a Bridge for Different Incidence Angles

A two-dimensional mathematical model is used to simulate the influence of water flow on the piers of a bridge for different incidence angles.In particular,a finite volume method is used to discretize the Navier-Stokes control equations and calculate the circumferential pressure coefficient distribution on the bridge piers’surface.The results show that the deflection of the flow is non-monotonic.It first increases and then decreases with an increase in the skew angle.

河道斜交桥梁壅水及流场特性分析

圆端桥墩是平原河道内一种常见的桥墩型式,为探究斜交圆端桥墩不同布置方式引起的壅水特性和水流流态变化,建立三维数值模型,采用SIMPLE算法耦合k-ε紊流模型求解N-S方程组,应用VOF法追踪自由液面,分析了单个桥墩壅水特性、绕流流场和升阻力系数随斜交角度变化的规律。研究结果表明:下游墩前壅水高度最大,壅水长度最长,上游墩前冲高值最大;水流绕流经过上游桥墩后偏向下游桥墩侧,桥墩垂直桥轴线布置方式绕流形成的壅水叠加效应更明显;斜交桥梁布置采取圆端桥墩时,桥墩顺水流布置,可有效减小阻水宽度与壅水高度,弱化流场结构变化。

Ultra-High Performance Concrete: An Advanced Solution for Accelerated Bridge Pier Cap Rehabilitation and Bearing Replacement

The objective of this paper is to propose and illustrate feasibility, approach, validation as per prevailing codes and design standards, specification to rehabilitate bridge pier cap by using Ultra-High Performance Concrete (UHPC). The evaluation of existing pier caps and bearings indicates that the complete removal of existing bearing is undesirable due to 1) massive size of bearing 2) difficulty in cutting through the thick components of existing bearing 3) deeply anchored lower shoe of existing bearings 4) huge cost and time required to erect temporary support system for superstructure to facilitate the construction of new piers. To overcome these difficulties, UHPC could be cast around the lower shoe up to the existing bearing pin. This UHPC cast could be used to support jacks and temporary bearings. The new low height permanent bearing could then be installed after removing the upper shoe of the existing bearing. In the present research, first properties of UHPC are summarized followed by evaluation of case studies to check feasibility of the solution to rehabilitate pier cap by using UHPC. The complex load paths in pier cap are idealized by using validated strut and tie model as per prevailing AASHTO LRFD Bridge Design Specification.

An Important Film: Polychromy in the Pier Luigi Nervi Halls at the Turin Exhibition Center

Hidden by several layers of white paint,the almost forgotten polychromy of Nervi’s exhibition halls emerges from historical images,not necessarily intended to document the complex,but rather as a setting for exhibitions,fairs or film and advertising sets.Historical documentation reveals Nervi’s presence on the building site and his desire to supervise the finishing phases.The first stratigraphic investigations also testify to his attention color,as well as the subsequent transformations of use.Specific theoretical and technical issues regarding the conservation of the pictorial layers in relation to the conservation of the reinforced concrete elements are outlined.Furthermore,the use of polychromy in combination with the original employment of natural and artificial light sources introduces new facets into the analysis of Nervi’s work,offering the opportunity for original reflection.This is particularly true if we consider the impact of the interventions carried out so far,even those considered non-invasive,such as routine maintenance operations and some technological upgrades.

PIER模式在落实大学英语视听说教学课程思政中的应用研究——以《新视野大学英语视听说教程(思政智慧版)》为例

大学英语视听说教学是大学英语教学至关重要的一部分,但对其课程思政的研究还有待完善,本研究以《新视野大学英语视听说教程(思政智慧版)》为抓手,通过深挖教材寻找大学英语视听说教学课程思政的切入点,讨论了PIER模式在视听说课程思政育人中的应用。大学英语视听说课程思政应当以教材为切入点,PIER模式实现了大学英语视听说教学过程与育人过程浑然天成,使学生在习得语言技能的同时收获德育教育。

台阶式沉井等效墩宽计算方法探究

桥梁工程中存在形状各异的桥墩,在研究不同截面桥墩的局部冲刷特性时,桥墩尺寸的定量描述非常重要。以台阶式沉井结构为研究对象,梳理并分析了国内外相关等效桥墩宽度计算方法,发现各类公式本质上为计算不同条件下的桥墩平均阻水宽度。开展了台阶式沉井局部冲刷试验研究,基于试验数据对比分析了各类等效墩宽计算方法的计算结果,发现Melville和Raudkivi的等效墩宽计算公式能够较好地估算考虑动床条件下台阶式沉井的平均阻水宽度;进一步收集了国内外193组台阶式沉井类结构的局部冲刷试验数据,数据集统计分析结果显示Melville和Randkivi的等效墩宽计算公式能够较为准确且保守地量化大多数台阶式沉井类结构的截面非均匀性;最后基于数据集冲深墩宽比统计结果对该公式近似方法的合理性进行了讨论。

基于新的改进Bouc-Wen模型的预制RC桥墩滞回模型研究

Bouc-Wen-Baber-Noori(BWBN)模型是改进的Bouc-Wen模型。BWBN模型可以较好地描述钢筋混凝土结构在强震作用下的捏缩效应,但由于BWBN模型中“捏缩效应”函数复杂且参数较多,其计算效率较低。针对该问题,该文基于近似狄拉克δ函数构建更简单、高效的“捏缩效应”函数,进而提出了新的改进Bouc-Wen(MBW)模型,它可以用更少的参数来实现捏缩效应。基于预制RC桥墩的拟静力试验数据来验证MBW模型的有效性,利用MATLAB遗传算法工具箱对BWBN模型和MBW模型进行参数识别,结果表明,该文提出的MBW模型具有更高的计算精度。

跨海铁路桥梁深水基础冲刷数值模拟

拟建头门港铁路支线(头门港站—头门港东站)二期工程位于浙江省东部海域,跨海铁路头门港大桥所在海域潮汐现象显著,波高较大,基础冲刷明显。首先选择7个典型桥墩,分别采用经验公式(孙志林公式和韩海骞公式)、JTG C30—2015《公路工程水文勘测设计规范》公式、美国HEC-18公式及数值模拟方法计算桥墩冲刷深度,基于百年一遇水位采用Das公式计算冲刷坑范围。然后采用半经验半理论的冲淤计算公式,计算冲淤平衡后水深变化量。通过与理论公式计算的局部冲刷深度对比,验证了数值模拟方法用于桥墩局部冲刷分析的可行性。结果表明:不管桥墩承台顺桥向尺寸如何变化,孙志林公式和HEC-18公式计算的冲刷深度偏大,韩海骞公式计算值最小,因此桥梁设计时宜采用规范公式计算冲刷深度;总体上桥墩承台顺桥向尺寸越大,冲刷坑面积越大;桥梁建成后水深下降了0.3~0.7 m,一般冲刷深度在3~5 cm,故分析该桥址处局部冲刷时可不考虑一般冲刷的影响;承台顺桥向尺寸在8~11 m时,与孙志林公式计算的局部冲刷深度相比,数值模拟值和规范公式计算值更接近,可采用数值模拟方法进行桥墩局部冲刷分析。

预制拼装铁路重力式桥墩的抗震性能研究

为适应中国铁路建设向高烈度震区快速发展的需要,解决传统预制拼装桥墩墩柱及承台连接位置薄弱等问题,提出一种灌浆波纹管连接的模块化预制拼装桥墩体系,通过设置承台与墩身塑性区域共同浇筑及墩底局部无黏结段增强桥墩的抗震性能。制作1个局部无黏结整体现浇铁路重力式桥墩模型和1个局部无黏结预制拼装铁路重力式桥墩模型开展拟静力试验,并结合有限元分析,进行预制拼装铁路重力式桥墩抗震性能研究。结果表明:局部无黏结预制拼装桥墩整体连接性能稳定,可通过墩底塑性区域破坏与墩身及节段间的摇摆实现共同消能,其破坏模式表现为墩底塑性区域的弯曲破坏,未发生破坏位置转移现象;局部无黏结预制拼装桥墩等效塑性区域高度比整体现浇桥墩降低,抗侧向水平承载力与耗能能力提升显著,位移延性能力良好,可适应更大加载位移,最终累积耗能增长64.3%;结构接缝位置连接稳定可靠,同等加载位移下等效刚度基本一致,抗震性能得到明显提高;预制节段划分对预制拼装铁路重力式桥墩抗震性能的影响不大。

混凝土格构式桥墩连续刚构桥地震响应影响参数分析

为研究混凝土格构式桥墩几何参数对连续刚构桥地震响应的影响,以某(65+4×120+65)m连续刚构桥为背景,建立全桥有限元模型,采用反应谱法和非线性时程法分析混凝土格构式桥墩单肢截面尺寸、单肢纵向间距、系梁道数对该桥动力特性和地震响应的影响规律。结果表明:混凝土格构式桥墩单肢截面尺寸、单肢纵向间距、系梁道数对连续刚构桥的各阶振型基本没有影响;随着单肢截面尺寸、单肢纵向间距的增大及系梁道数的增加,连续刚构桥自振频率均逐渐增加,其中系梁道数对其影响较大,随着系梁道数的增加,该桥1阶、2阶自振频率逐渐增加;罕遇地震作用下,随着单肢截面尺寸、单肢纵向间距的增大及系梁道数的增加,桥墩位移逐渐减小;随着单肢截面尺寸的增大,桥墩内力明显增加,而单肢纵向间距对桥墩内力影响较小;随着系梁道数的增加,桥墩剪力逐渐增加,而墩顶及墩底弯矩逐渐降低;单肢截面尺寸、单肢纵向间距、系梁道数对墩顶、墩底塑性转角影响很小,但是墩顶、墩底塑性转角随格构式桥墩单肢截面尺寸的增大呈先增大后减小的趋势。

三水河特大桥桥墩温度场及温度效应研究

为研究温度效应对连续刚构桥空心薄壁墩受力行为的影响,以(98+5×185+98)m变截面预应力混凝土连续刚构桥——三水河特大桥主桥为背景,通过现场温度场测试,研究桥墩垂直温度场和水平温度场的分布规律,并以实测温度场为依据,选取对桥墩刚度影响较大的桥墩高度、顺桥向宽度和壁厚作为关键参数,分析整体均匀温度T和梯度温度ΔT对空心薄壁墩受力的影响。结果表明:实测桥墩垂直温度场随着墩高的变化分布差异较小,水平温度场受日光照射影响较大,桥墩夏季的梯度温度值约为冬季的2倍。墩高对桥墩温度应力的影响基本呈反比关系,顺桥向宽度对墩底温度应力的影响呈线性增长趋势,壁厚与温度应力呈反比关系。对于长联刚构桥,为减小桥墩的温度效应,建议边主墩高度不宜小于60 m,桥墩顺桥向宽度宜尽量减小,桥墩壁厚宜取80~100 cm。