Stochastic sampled-data multi-objective control of active suspension systems for in-wheel motor driven electric vehicles

This paper addresses the sampled-data multi-objective active suspension control problem for an in-wheel motor driven electric vehicle subject to stochastic sampling periods and asynchronous premise variables.The focus is placed on the scenario that the dynamical state of the half-vehicle active suspension system is transmitted over an in-vehicle controller area network that only permits the transmission of sampled data packets.For this purpose,a stochastic sampling mechanism is developed such that the sampling periods can randomly switch among different values with certain mathematical probabilities.Then,an asynchronous fuzzy sampled-data controller,featuring distinct premise variables from the active suspension system,is constructed to eliminate the stringent requirement that the sampled-data controller has to share the same grades of membership.Furthermore,novel criteria for both stability analysis and controller design are derived in order to guarantee that the resultant closed-loop active suspension system is stochastically stable with simultaneous𝐻2 and𝐻∞performance requirements.Finally,the effectiveness of the proposed stochastic sampled-data multi-objective control method is verified via several numerical cases studies in both time domain and frequency domain under various road disturbance profiles.

Design and Optimization of Interior Permanent Magnet(IPM)Motor for Electric Vehicle Applications

This paper explores some design parameters of an interior permanent magnet synchronous motor that contribute to enhancing motor performance.Various geometry parameters such as magnet dimension,machine diameter,stator teeth height,and number of poles are analyzed to compare overall torque,power,and torque ripples in order to select the best design parameters and their ranges.Pyleecan,an open-source software,is used to design and optimize the motor for electric vehicle applications.Following optimization with Non-dominated Sorting Genetic Algorithm(NSGA-Ⅱ),two designs A and B were obtained for two objective functions and the corresponding torque ripples values of the design A and B were later reduced by 32%and 77%.Additionally,the impact of different magnet grades on the output performances is analyzed.

MPC-based Torque Distribution for Planar Motion of Four-wheel Independently Driven Electric Vehicles:Considering Motor Models and Iron Losses

The most critical obstacle for four-wheel independently driven electric vehicles(4WID-EVs)is the driving range.Being the actuators of 4WID-EVs,motors account for its major power consumption.In this sense,by properly distributing torques to minimize the power consumption,the driving range of 4WID-EV can be effectively improved.This paper proposes a model predictive control(MPC)-based torque distribution scheme,which minimizes the power consumption of 4WID-EVs while guaranteeing its tracking performance of planar motions.By incorporating the motor model considering iron losses,the optimal torque distribution can be achieved without an additional torque controller.Also,for this reason,the proposed control scheme is computationally efficient,since the power consumption term to be optimized,which is expressed as the product of the motor voltages and currents,is much simpler than that derived from the efficiency map.With reasonable simplification and linearization,the MPC problem is converted to a quadratic programming problem,which can be solved efficiently.The simulation results in MATLAB and CarSim co-simulation environments demonstrate that the proposed scheme effectively reduces power consumption with guaranteed tracking performance.

Decentralized Dynamic Event-Triggered Communication and Active Suspension Control of In-Wheel Motor Driven Electric Vehicles with Dynamic Damping

This paper addresses the co-design problem of decentralized dynamic event-triggered communication and active suspension control for an in-wheel motor driven electric vehicle equipped with a dynamic damper. The main objective is to simultaneously improve the desired suspension performance caused by various road disturbances and alleviate the network resource utilization for the concerned in-vehicle networked suspension system. First, a T-S fuzzy active suspension model of an electric vehicle under dynamic damping is established. Second,a novel decentralized dynamic event-triggered communication mechanism is developed to regulate each sensor's data transmissions such that sampled data packets on each sensor are scheduled in an independent manner. In contrast to the traditional static triggering mechanisms, a key feature of the proposed mechanism is that the threshold parameter in the event trigger is adjusted adaptively over time to reduce the network resources occupancy. Third, co-design criteria for the desired event-triggered fuzzy controller and dynamic triggering mechanisms are derived. Finally, comprehensive comparative simulation studies of a 3-degrees-of-freedom quarter suspension model are provided under both bump road disturbance and ISO-2631 classified random road disturbance to validate the effectiveness of the proposed co-design approach. It is shown that ride comfort can be greatly improved in either road disturbance case and the suspension deflection, dynamic tyre load and actuator control input are all kept below the prescribed maximum allowable limits, while simultaneously maintaining desirable communication efficiency.

Torque Distribution of Electric Vehicle with Four In-Wheel Motors Based on Road Adhesion Margin

With the worsening of energy crisis and environmental pollution,electric vehicles with four in?wheel motors have been paid more and more attention. The main research subject is how to reasonably distribute the driving torque of each wheel. Considering the longitudinal motion,lateral motion,yaw movement and rotation of the four wheels,the tire model and the seven DOF dynamic model of the vehicle are established in this paper. Then,the torque distribution method is proposed based on road adhesion margin,which can be divided into anti ? slip control layer and torque distribution layer. The anti?slip control layer is built based on sliding mode variable structure control,whose main function is to avoid the excessive slip of wheels caused by road conditions. The torque distribution layer is responsible for selecting the torque distribution method based on road adhesion margin. The simulation results show that the proposed torque distribution method can ensure the vehicle quickly adapt to current road adhesion conditions,and improve the handling stability and dynamic performance of the vehicle in the driving process.

Electromagnetic analysis and design of in-wheel motor of micro-electric vehicle based on Maxwell

To obtain a good drivability and high efficiency of the micro-electric vehicle, a new driving in-wheel motor design was analyzed and optimized. Maxwell software was used to build finite element simulation model of the driving in-wheel motor. The basic features and starting process were analyzed by field-circuit coupled finite element method. The internal complicated magnetic field distribution and dynamic performance simulation were obtained in different positions. No-load and load characteristics of the driving in-wheel motor was simulated, and the power consumption of materials was computed. The conformity of the final simulation results with the experimental data indicates that this method can be used to provide a theoretical basis to make further optimal design of this new driving in-wheel motor and its control system, so as to improve the starting torque and reduce torque ripple of the motor. This method can shorten the development cycle of in-wheel motors and save development costs, which has a wide range of engineering application value.

Sensorless torque control scheme of induction motor for hybrid electric vehicle

In this paper, the sensorless torque robust tracking problem of the induction motor for hybrid electric vehicle （HEV） applications is addressed, Because motor parameter variations in HEV applications are larger than in industrial drive system, the conventional field-oriented control （FOC） provides poor performance. Therefore, a new robust PI-based extension of the FOC controller and a speed-flux observer based on sliding mode and Lyapunov theory are developed in order to improve the overall performance. Simulation results show that the proposed sensorless torque control scheme is robust with respect to motor parameter variations and loading disturbances. In addition, the operating flux of the motor is chosen optimally to minimize the consumption of electric energy, which results in a significant reduction in energy losses shown by simulations.

Driving Range Parametric Analysis of Electric Vehicles Driven by Interior Permanent Magnet Motors Considering Driving Cycles

This paper presents parametric analysis of driving range of electric vehicles driven by V-type interior permanent magnet motors aiming at maximum driving range,i.e.,minimal total energy consumption of the motors over a driving cycle.Influence of design parameters including tooth width,slot depth,split ratio(the ratio of inner diameter to outer diameter of the stator),and V-type magnet angle on the energy consumption of the motors and driving range of electric vehicles over a driving cycle is investigated in detail.The investigation is carried out for two typical driving cycles with different characteristics to represent different conditions:One is high-speed,low-torque cycle-Highway Fuel Economy Test and the other is low-speed,high-torque cycle-Artemis Urban Driving Cycle.It shows that for both driving cycles,the same parameters may have different influence on the energy consumption of the motors,as well as driving range of electric vehicles.

Design andtwo-objective simultaneous optimization of torque controller for switched reluctance motor in electric vehicle

In order to reduce the torque ripple,increase the average torque and optimize the drive performance of the switched reluctance motor (SRM),the nonlinear dynamic model of SRM is established in the MATLAB /Simulink environment.The effects of the turn-on and turn-off angles are investigated by the simulation results of the dynamic model,and the function is made among the rotor speed,turn-on angle and turn-off angle.To optimize the torque dynamic performance,the two-objective simultaneous optimization function is proposed by two weight factors.And the optimized turn-on and turn-off angles as functions of rotor speed are developed by using the simultaneous optimization method.Then the optimized torque controller is designed based on the optimized turn-on and turn-off angles.The simulation results show that the optimized torque controller designed in this paper can effectively reduce the torque ripple and increase the average torque,and optimize the torque dynamic performance of the SRM.

Auto-Test on Motor Temperature Rising in Electric Vehicles with Mutual MRAS

A new method to calculate the motor temperature rising in electric vehicle （EV） is proposed based on the stator resistance identification. The measure theory of the motor temperature rising with the stator resistance is discussed at first. An enhanced magnetism motor dynamic math model is built which is the research object. Then the resistance identification system model is built on the mutual model reference adaptive,system （MRAS） theory. The simulation diagram of the mutual MRAS model is constructed and the resistance identification performance is studied in different motor states. Simulation results indicate that the stator resistance identification model with the mutual MRAS is effective. At the same time, the identification of motor temperature rising is possible with the identification of the stator resistance.

Motion Analysis of an Electric Vehicle with Two Independent Drive Motors

Motion analyses are performed with the help of stability and simulation analysis, which can provide theoretical bases for applications of an electric vehicle with two independent drive motors. Compared with one-motor drive electric vehicle, the two-motor drive electric vehicle has the advantage of easy layout, simple power train and good drivability and handling characteristics. Analysis shows the method connecting armatures of two DC motors in parallel can function as mechanical differential without a steering sensor, which can simplify structure and increase reliability of the controller. Computer simulations and experiment are carried out to verify conclusions.

Design and Development of a Vector Control System of Induction Motor Based on Dual CPU for Electric Vehicle

A vector control system for electric vehicle (EV) induction motor drive system is designed and developed. Its hardware system based on dual CPU(microcomputer 80C196KC and DSP TMS320F2407) is implemented. The fundamental mathematics equations of induction motor in the general synchronously rotating reference frame ( M T frame) used for vector control are achieved by coordinate transformation. Rotor flux equation and torque equation are deduced. According to these equations, an induction motor mathematical model and rotor flux observer model are built separately. The rotor flux field oriented vector control method is implemented based on these models in system software, some of the simulation results with Matab/Simulink are given. The simulation results show that the vector control system for EV induction motor drive system has better static and dynamic performance, and the rotor flux field oriented vector control method was practically verified.

Multi-objective Optimization of Differential Steering System of Electric Vehicle with Motorized Wheels

A differential steering system is presented for electric vehicle with motorized wheels and a dynamic model of three-freedom car is built.Based on these models,the quantitative expressions of the road feel,sensitivity,and operation stability of the steering are derived.Then,according to the features of multi-constrained optimization of multi-objective function,a multi-island genetic algorithm(MIGA)is designed.Taking the road feel and the sensitivity of the steering as optimization objectives and the operation stability of the steering as a constraint,the system parameters are optimized.The simulation results show that the system optimized with MIGA can improve the steering road feel,and guarantee the operation stability and steering sensibility.

Study on Modeling and Control Strategy for Electric Drive Motor of Tracked Vehicles

Aimed at the requirements for electric transmission system of a military tracked vehicle, the motor's design indexes were analysed and calculated. A model based on saturate inductance parameter of interior permanent magnet (IPM) synchronous motor was brought forward by using finite element analysis. And its control strategy based on the largest running capability was studied also. The experiment results for a scale model show that the modelling method improves the model's accuracy, and the motor's control strategy is effective.

Temperature Research of Permanent Magnet Brushless DC Motor for Electric Balanced Vehicle

A power system structure composed of a brushless DC motor and a cycloidal reducer for electric balanced vehicle has been proposed, and the temperature of important components in this structure would be discussed. The loss generated by the cycloid reducer is negligible, it’s only need to analyze the thermal field of motor. Since the temperature change will affect the material properties of the target motor, the electromagnetic and temperature fields, involved in the motor, are selected for coupling calculation to determine whether the final temperature distribution can meet the requirements of vehicle for use.

The Summary of the Research on the Compound Braking Strategy of Four Wheel Hub Motor Drive Electric Vehicle

This paper describes in detail three kinds of typical compound braking strategy of wheel motor drive electric vehicle and summarizes the current commonly used strategies based on the three typical strategies developed. In the end, a new compound braking strategy is proposed;that is, we take braking mode classify, ECE regulations and SOC value of the battery as an important reference of braking force that joins the motor braking force, as well as we join the different identification models;according to the different braking modes, the purpose is that we can apply the different braking program.