Development of a high-repetition-rate lumped-inductance kicker magnet prototype for the beam switchyard of SHINE

The Shanghai high-repetition-rate X-ray free-electron laser and extreme light facility(SHINE)operates at a maximum repetition rate of 1 MHz.Kicker magnets are key components that distribute electron bunches into three different undulator lines in a bunch-by-bunch mode.The kicker field width must be less than the time interval between bunches.A lumpedinductance kicker prototype was developed using a vacuum chamber with a single-turn coil.The full magnetic field strength was 0.005 T.This paper presents the requirements,design considerations,design parameters,magnetic field calculations,and measurements of the kicker magnets.The relevant experimental results are also presented.The pulse width of the magnetic field was approximately 600 ns,and the maximum operation repetition rate was 1 MHz.The developed kicker satisfies the requirements for the SHINE project.Finally,numerous recommendations for the future optimization of kicker magnets are provided.

Repetitive transcranial magnetic stimulation in Alzheimer’s disease:effects on neural and synaptic rehabilitation

Alzheimer’s disease is a neurodegenerative disease resulting from deficits in synaptic transmission and homeostasis.The Alzheimer’s disease brain tends to be hyperexcitable and hypersynchronized,thereby causing neurodegeneration and ultimately disrupting the operational abilities in daily life,leaving patients incapacitated.Repetitive transcranial magnetic stimulation is a cost-effective,neuro-modulatory technique used for multiple neurological conditions.Over the past two decades,it has been widely used to predict cognitive decline;identify pathophysiological markers;promote neuroplasticity;and assess brain excitability,plasticity,and connectivity.It has also been applied to patients with dementia,because it can yield facilitatory effects on cognition and promote brain recovery after a neurological insult.However,its therapeutic effectiveness at the molecular and synaptic levels has not been elucidated because of a limited number of studies.This study aimed to characterize the neurobiological changes following repetitive transcranial magnetic stimulation treatment,evaluate its effects on synaptic plasticity,and identify the associated mechanisms.This review essentially focuses on changes in the pathology,amyloidogenesis,and clearance pathways,given that amyloid deposition is a major hypothesis in the pathogenesis of Alzheimer’s disease.Apoptotic mechanisms associated with repetitive transcranial magnetic stimulation procedures and different pathways mediating gene transcription,which are closely related to the neural regeneration process,are also highlighted.Finally,we discuss the outcomes of animal studies in which neuroplasticity is modulated and assessed at the structural and functional levels by using repetitive transcranial magnetic stimulation,with the aim to highlight future directions for better clinical translations.

英语辞格REPETITION与相关汉语修辞格的对比及其翻译

英语辞格Repetition是一种常用的结构上的修辞手法,主要分为七种形式。汉语修辞格中的反复也是被普遍运用的常见修辞手段,可分为三种形式。本文以英汉、汉英对照的形式,分别说明两者的特点,并进行区别。文中还将Repetition与顶真及回环两种汉语修辞格做了对比,并对英语辞格Repetition和汉语修辞格反复的翻译技巧和规律进行调查。

Criticism on the Critical Approaches in J. Hillis Miller's Fiction and Repetition:Seven English Novels

Fiction and Repetition is and will remain a distinguished deconstructionist guide of literary criticism. However, after detailed and systematic research, I also find some shortcomings in this important academic work: Firstly, written in the metaphysical language, Fiction and Repetition can never succeed in escaping the logocentrism and binary opposition inherent in this language.Secondly, based on Saussure's argument on langue, the monograph's view of indeterminacy of literary work's meaning is theoretically correct but practically inadequate. Last but not the least, Miller's proposal on repetition also has some limitations. By taking into account both the work's merits and demerits, we can gain a more comprehensive outlook on Miller's idea of repetition as well as the deconstruction theory of literary criticism in general.

Key technologies implementation of high-repetition-rate satellite laser ranging

Satellite laser ranging （SLR） is one of the major space geodetic instruments, which has various applications in earth science. In this paper, we introduce several issues regarding the key technology implementation of high-repetition-rate SLR system. Compared with traditional technology, using kHz and 8ps pulse width laser component, the data quantity and quality of high-repetition-rate satellite laser ranging （SLR） can be significantly improved. The characteristics of high-repetition-rate laser ranging and the key technologies are presented, including the event timer with the precision of picosecond, the generation of range gate signal, and so on. All of them are based on the Field Programmable Gate Arrays （FPGA） and tested on China mobile SLR system-TROS1000. Finally, the observations of satellite Beacon-C are given.

High power diode-pumped passively mode-locked Nd:YVO_4 laser at repetition rate of 3.2 GHz

A compact high power diode-pumped passively mode-locked Nd:YVO_4 laser with high repetition rate is realized.Using an Nd:YVO_4 crystal and a semiconductor saturable absorber mirror(SESAM) in the oscillator, the picosecond pulse output with an average power of 1.38 W, a repetition rate of 3.24 GHz, and a pulse duration of 11.4 ps is achieved. After one stage of amplification, the final output power reaches 11.34 W, corresponding to a total optical-to-optical efficiency of about 32%. The root mean square(RMS) value of power fluctuation is demonstrated to be less than 0.6% in 24 hours,showing a superior stability with the compact configuration.

The L4n laser beamline of the P3-installation:Towards high-repetition rate high-energy density physics at ELI-Beamlines

The P3 installation of ELI-Beamlines is conceived as an experimental platform for multiple high-repetition-rate laser beams spanning time scales from femtosecond via picosecond to nanosecond.The upcoming L4n laser beamline will provide shaped nanosecond pulses of up to 1.9 kJ at a maximum repetition rate of 1 shot/min.This beamline will provide unique possibilities for high-pressure,high-energy-density physics,warm dense matter,and laser–plasma interaction experiments.Owing to the high repetition rate,it will become possible to obtain considerable improvements in data statistics,in particular,for equation-of-state data sets.The nanosecond beam will be coupled with short sub-picosecond pulses,providing high-resolution diagnostic tools by either irradiating a backlighter target or driving a betatron setup to generate energetic electrons and hard X-rays.

High-repetition-rate few-attosecond high-quality electron beams generated from crystals driven by intense X-ray laser

Advances in X-ray laser sources have paved the way to relativistic attosecond X-ray laser pulses and opened up the possibility of exploring highenergy-density physics with this technology.With particle-in-cell simulations,we investigate the interaction of realistic metal crystals with relativistic X-ray laser pulses of parameters that will be available in the near future.A wakefield of the order of TV/cm is excited in the crystal and accelerates trapped electrons stably even though the wakefield is locally modulated by the crystal lattice.Electron injection either occurs at the sharp crystal-vacuum boundary or is controlled by coating the crystal with a high-density film.High-repetition-rate attosecond(20 as)monoenergetic electron beams of energy 125 MeV,charge 100 fC,and emittance 1.6310−9mrad can be produced by shining MHz X-ray laser pulses of energy 2.1 mJ onto coated crystals several micrometers thick.Such a miniature crystal accelerator,which has high reproducibility and allows sufficient control of the parameters of the electron beams,greatly expands the applications of X-ray free electron lasers.For example,it could serve as an ideal electron source for ultrafast electron diffraction and ultrafast electron microscopy to achieve attosecond resolution.

High efficiency sub-nanosecond electro-optical Q-switched laser operating at kilohertz repetition frequency

Based on a theoretical model of Q-switched laser with the influences of the driving signal sent to the Pockels cell and the doping concentration of the gain medium taken into account,a method of achieving high energy sub-nanosecond Q-switched lasers is proposed and verified in experiment.When a Nd:YVO4 crystal with a doping concentration of 0.7 at.%is used as a gain medium and a driving signal with the optimal high-level voltage is applied to the Pockels cell,a stable single-transverse-mode electro-optical Q-switched laser with a pulse width of 0.77 ns and a pulse energy of 1.04 mJ operating at the pulse repetition frequency of 1 kHz is achieved.The precise tuning of the pulse width is also demonstrated.

The 266-nm ultraviolet-beam generation of all-fiberized super-large-mode-area narrow-linewidth nanosecond amplifier with tunable pulse width and repetition rate

We report on a compact, stable, all-fiberized narrow-linewidth(0.045 nm) pulsed laser source emitting laser beam with a wavelength of 266 nm, and tunable pulse width and repetition rate. The system is based on all-fiberized nanosecond amplifier architecture, which consists of Yb-doped fiber preamplifiers and a super-large-mode-area Yb-doped fiber power amplifier. The fiber amplifier with a core of 50 μm is used to raise the threshold of the stimulated Brillouin scattering(SBS) effect and to obtain high output power and single pulse energy. Using lithium triborate(LBO) crystal and betabarium borate(BBO) crystal for realizing the second-harmonic generation(SHG) and fourth-harmonic generation(FHG),we achieve 17 μJ(1.73 W) and 0.66 μJ(66 mW), respectively, at wavelengths of 532 nm and 266 nm and a repetition rate of 100 kHz with pulse width of 4 ns. This source has great potential applications in fluorescence research and solar-blind ultraviolet optical communication.

Passive Q-Switching of a Yb:LuVO_4 Laser with Cr^(4+):YAG:Approaching the Intrinsic Upper Limit of Repetition Rate

We demonstrate a diode pumped Yb：LuVO4 laser that can be passively Q-switched by a Cr^（4＋）：YAG saturable absorber having an initial transmission as high as 99.3%.A maximum pulsed output power of 2.35 W is generated at a repetition rate of 285.7 kHz,approaching or very near the intrinsic upper limit imposed by the recovery time of the Cr^（4＋）：YAG saturable absorber,and the resulting pulse energy,duration and peak power are,respectively,8.2μJ,39.2ns and 0.209kW.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Repetition and EFL Vocabulary Learning

本文通过分析英语词汇学习这一复杂过程,提出重复记忆有助于学生提高单词识记的效率,纠正学生固有的对单词学习的偏见和不正确认识;并且提供了具体的操作方法,如间隔性重复和词义索回记忆法。

Contribution of glial cells to the neuroprotective effects triggered by repetitive magnetic stimulation:a systematic review

Repetitive transcranial magnetic stimulation has been increasingly studied in different neurological diseases,and although most studies focus on its effects on neuronal cells,the contribution of nonneuronal cells to the improvement trigge red by repetitive transcranial magnetic stimulation in these diseases has been increasingly suggested.To systematically review the effects of repetitive magnetic stimulation on non-neuronal cells two online databases.Web of Science and PubMed were searched fo r the effects of high-frequency-repetitive transcranial magnetic stimulation,low-frequencyrepetitive transcranial magnetic stimulation,intermittent theta-bu rst stimulation,continuous thetaburst stimulation,or repetitive magnetic stimulation on non-neuronal cells in models of disease and in unlesioned animals or cells.A total of 52 studies were included.The protocol more frequently used was high-frequency-repetitive magnetic stimulation,and in models of disease,most studies report that high-frequency-repetitive magnetic stimulation led to a decrease in astrocyte and mic roglial reactivity,a decrease in the release of pro-inflammatory cyto kines,and an increase of oligodendrocyte proliferation.The trend towards decreased microglial and astrocyte reactivity as well as increased oligodendrocyte proliferation occurred with intermittent theta-burst stimulation and continuous theta-burst stimulation.Few papers analyzed the low-frequency-repetitive transcranial magnetic stimulation protocol,and the parameters evaluated were restricted to the study of astrocyte reactivity and release of pro-inflammatory cytokines,repo rting the absence of effects on these paramete rs.In what concerns the use of magnetic stimulation in unlesioned animals or cells,most articles on all four types of stimulation reported a lack of effects.It is also important to point out that the studies were developed mostly in male rodents,not evaluating possible diffe rential effects of repetitive transcranial magnetic stimulation between sexes.This systematic review supports that thro ugh modulation of glial cells repetitive magnetic stimulation contributes to the neuroprotection or repair in various neurological disease models.Howeve r,it should be noted that there are still few articles focusing on the impact of repetitive magnetic stimulation on non-neuronal cells and most studies did not perform in-depth analyses of the effects,emphasizing the need for more studies in this field.

Generation of 10 fs Ti:sapphire laser at repetition rate of 525 MHz and measurement of carrier-envelope phase frequency

This paper presents a Kerr-lens mode-locked Ti：sapphire laser at the repetition rate of 525 MHz, stable laser pulse as short as 10 fs with average output power of 480 mW is obtained. By injecting the pulse into photonics crystal fibre, octave-spanning spectrum covered from 500 to 1050 nm is generated, carrier-envelope phase frequency with signal-to- noise ratio of 31dB is measured, which paves the way for the generation of a compact frequency comb.

Elemental analysis of copper alloy by high repetition rate LA-SIBS using compact fiber spectrometer

High repetition rate laser-ablation spark-induced breakdown spectroscopy(HRR LA-SIBS) was first used to analyze trace elements in copper alloy samples. The 1064 nm output of an acoustooptically Q-switched Nd:YAG laser operated at a pulse repetition rate of 1 kHz was utilized to ablate copper alloy and to form original plasma, spark-discharge was applied to further breakdown the ablated samples and enhance the emission of the laser-induced plasma. A compact multichannel fiber spectrometer was used to analyze the plasma emission under nongated operation mode. Under the assistance of high repetition rate spark discharge, the plasma emission was able to be improved significantly. The determined limits of the detection of lead and aluminum were 15.5 ppm and 1.9 ppm by HRR LA-SIBS, respectively, which were 11 and 6 folds better than that determined by HRR LIBS under the same laser-ablation condition. This work demonstrates the feasibility of using fiber spectrometer to analyze plasma emission under non-gated operation mode and the possibility of building a portable HRR LA-SIBS system for rapid elemental analysis of copper alloys and other solid samples.

Generation of high-energy dual-wavelength domain wall pulse with low repetition rate in an HNLF-based fiber ring laser

The generation of high-energy dual-wavelength domain wall pulse with a low repetition rate is demonstrated in a highly nonlinear fiber （HNLF）-based fiber ring laser. By introducing the intracavity birefringence-induced spectral filtering effect, the dual-wavelength lasing operation can be achieved. In order to enhance the cross coupling effect between the two lasing beams for domain wall pulse formation, a 215-m HNLF is incorporated into the laser cavity. Experimentally, it is found that the dual-wavelength domain wall pulse with a repetition rate of 77.67 kHz could be efficiently obtained through simply rotating the polarization controller （PC）. At a maximum pump power of 322 mW, the 655-nJ single pulse energy in cavity is obtained. The proposed configuration provides a simpler and more efficient way to generate high energy pulse with a low repetition rate.

Science Letters:Controllable high repetition rate gain-switchedNd:YVO_4 microchip laser

We demonstrated a monolithic, compact, diode-pumped gain-switched Nd:YVO4 laser at 1.064 μm wavelength with controllable repetition rate of 1 Hz to 25 kHz. Stable gain-switched pulse train with maximum repetition rate of 25 kHz and pulse width of 16 ns was obtained.

Alamouti code based on block repetition in FBMC/OQAM systems

In this paper,we address the Alamouti code in Filter-Bank Multicarrier with Offset Quadrature Amplitude Modulation(FBMC/OQAM)and propose a novel block-wise Alamouti code,in which a repeated block is designed to eliminate the imaginary interference among FBMC/OQAM symbols.The proposed approach exhibits a higher spectral efficiency than the conventional block-wise Alamouti scheme,as only one column of zero symbols is used as a guard interval instead of two.Furthermore,compared to the conventional scheme,the bit error ratio is improved in the proposed block-wise Alamouti,as the assumption on channel invariance at two adjacent sub-carriers is not required.Simulation results indicate that,with a significantly reduced overhead,the proposed Alamouti scheme achieves better performance over the conventional block-wise Alamouti scheme.

Laser back scatter: Limitation to higher repetition rate [kHz] Satellite Laser Ranging system

Satellite laser ranging(SLR)with higher repetition rate is the recent trend for its various advantages.Laser backscatter(coincidence between recently transmitted pulses and received pulses near the detector)is found to be a constraint for the repetition rates higher than 20 kHz,due to,overlapping with photons returning from a satellite with the present constellation of most of the SLR systems.Such an overlap occurs at every 75 km satellite distance change at 2 kHz repetition rate,and remains for about 7.5 km;for a 20 kHz system however,it will occur after every 7.5 km and remains for 7.5 km,resulting in constant backscatter overlap e leaving no chance to avoid it.The resulting noise is 5 times more than before causing a serious problem in detection and lowers the signal to noise ratio of the overall SLR system.However,decreasing energy per shot at higher repetition rates e assuming a constant power laser e the resulting backscatter may decrease fractionally.