Measuring solar irradiance profiles in the Arctic sea ice using fiber optic spectrometry via inclined holes

An irradiance profile measurement approach and profiling system were developed to measure the solar irradiance profile of the Arctic sea ice using fiber optic spectrometry.The approach involved using a miniature spectrometer to sense light signals collected and transmitted from a fiber probe.The fiber probe was small,and could thus move freely in inclined bore holes drilled in sea ice with its optical entrance pointing upward.The input-output relationship of the system was analyzed and built.Influence factors that determined the system output were analyzed.A correctional system output approach was proposed to correct the influence of these factors,and to obtain the solar irradiance profile based on the measurements outputted by this system.The overall performance of the system was examined in two ice floes in the Arctic during the 9th Chinese National Arctic Research Expedition.The measured solar irradiance profiles were in good agreement with those obtained using other commercially available oceanographic radiometers.The derived apparent optical properties of sea ice were comparable to those of similar sea ice measured by other optical instruments.

Experimental Study Optimizing Hole Cleaning-Cuttings Transport in Oil Drilling Engineering

With a clear understanding of the drilling fluid techniques and the cutting taking mechanism, a new advanced model is set up for analyzing field data and quantitative forecast of cutting taking mechanism. Therefore, a number of values affecting the drilling rate and the hole cleaning are studied over a wide range of parameters. Drilling data obtained under high borehole pressure conditions are analyzed to determine the causes of the reduction in rate of penetration (ROP) as the borehole pressure increases, which in some cases is caused by the buildup of rock debris under the bit. The theoretical achievement and testing conclusions can be very instructional for horizontal well drilling. Much higher annular velocities are required for effective hole cleaning in directional wells than in vertical wells. High viscosity muds are observed to provide better transport than low viscosity muds.

A High-Mathematical Model Optimizing Cuttings Transport in Oil Drilling Engineering

With special drilling operation equipment and specific conditions of geology, how does drilling fluid carry cuttings effectively? So far, it is still an urgent problem for drilling researchers to study. This work just aims at the actual engineering background to develop studying model. In this paper, according to non Newtonian fluid mechanics, the law of the solid liquid, two phase fluid flow and actual drilling engineering, the major factors affecting cuttings transport are drilling fluid velocity, hole inclination and fluid rheological properties. Getting a clear understanding of the law of drilling fluid and its cutting taking mechanism, this paper puts forward a model for analysis of field data and quantitative forecast of cutting taking capability of drilling fluid. The full scale annular test section was 6.1 m with 76 and 114 mm drillpipe in a 203 mm ID (wellbore diameter). Hole angle varied from 0° to 90°.

Improvement of Film Cooling Design for Turbine Vane Leading Edge Considering Combustor Outflow

As the interaction between the combustor and the turbine in the aero-engine continues to increase,the film cooling design considering the combustor swirling outflow has become the research focus.The swirling inflow and high-temperature gas first affect the vane leading edge(LE).However,no practical improved solution for the LE cooling design has been proposed considering the combustor swirling outflow.In this paper,the improved scheme of showerhead cooling is carried out around the two ways of adopting the laid-back-fan-shaped hole and reducing the coolant outflow angle.The film cooling effectiveness(η) and the coolant flow state are obtained by PSP(pressure-sensitive-paint) and numerical simulation methods,respectively.The research results show that the swirling inflow increases the film distribution inhomogeneity by imposing the radial pressure gradient on the vane to make the film excessively gather in some positions.The showerhead film cooling adopts the laid-back-fan-shaped hole to reduce the momentum when the coolant flows out.Although this cooling scheme improves the film attachment and increases the surface-averaged film cooling effectiveness(η_(sur)) by as much as15.4%,the film distribution inhomogeneity increases.After reducing the coolant outlet angle,the wall-tangential velocity of the coolant increases,and the wall-normal velocity decreases.Under the swirl intake condition,both ηand the film distribution uniformity are significantly increased,and the growth of η_(sur) is up to 16.5%.This paper investigates two improved schemes to improve the showerhead cooling under the swirl intake condition to provide a reference for the vane cooling design.