Shear behavior of intact granite under thermo-mechanical coupling and three-dimensional morphology of shear-formed fractures

The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear-formed fractures are prone to secondary instability,posing a severe threat to deep engineering.Although numerous studies regarding three-dimensional(3D)morphologies of fracture surfaces have been conducted,the understanding of shear-formed fractures under TM coupling conditions is limited.In this study,direct shear tests of intact granite under various TM coupling conditions were conducted,followed by 3D laser scanning tests of shear-formed fractures.Test results demonstrated that the peak shear strength of intact granite is positively correlated with the normal stress,whereas it is negatively correlated with the temperature.The internal friction angle and cohesion of intact granite significantly decrease with an increase in the temperature.The anisotropy,roughness value,and height of the asperities on the fracture surfaces are reduced as the normal stress increases,whereas their variation trends are the opposite as the temperature increases.The macroscopic failure mode of intact granite under TM coupling conditions is dominated by mixed tensileeshear and shear failures.As the normal stress increases,intragranular fractures are developed ranging from a local to a global distribution,and the macroscopic failure mode of intact granite changes from mixed tensileeshear to shear failure.Finally,3D morphological characteristics of the asperities on the shear-formed fracture surfaces were analyzed,and a quadrangular pyramid conceptual model representing these asperities was proposed and sufficiently verified.

Three-Dimensional Model Reconstruction of Nonwovens from Multi-Focus Images

The three-dimensional(3D)model is of great significance to analyze the performance of nonwovens.However,the existing modelling methods could not reconstruct the 3D structure of nonwovens at low cost.A new method based on deep learning was proposed to reconstruct 3D models of nonwovens from multi-focus images.A convolutional neural network was trained to extract clear fibers from sequence images.Image processing algorithms were used to obtain the radius,the central axis,and depth information of fibers from the extraction results.Based on this information,3D models were built in 3D space.Furthermore,self-developed algorithms optimized the central axis and depth of fibers,which made fibers more realistic and continuous.The method with lower cost could reconstruct 3D models of nonwovens conveniently.

Effect of the mineral spatial distribution heterogeneity on the tensile strength of granite:Insights from PFC3D-GBM numerical analysis

The mechanical characteristics of crystalline rocks are affected by the heterogeneity of the spatial distribution of minerals.In this paper,a novel three-dimensional(3D)grain-based model(GBM)based on particle flow code(PFC),i.e.PFC3D-GBM,is proposed.This model can accomplish the grouping of mineral grains at the 3D scale and then filling them.Then,the effect of the position distribution,geometric size,and volume composite of mineral grains on the cracking behaviour and macroscopic properties of granite are examined by conducting Brazilian splitting tests.The numerical results show that when an external load is applied to a sample,force chains will form around each contact,and the orientation distribution of the force chains is uniform,which is independent of the external load level.Furthermore,the number of high-strength force chains is proportional to the external load level,and the main orientation distribution is consistent with the external loading direction.The main orientation of the cracks is vertical to that of the high-strength force chains.The geometric size of the mineral grains controls the mechanical behaviours.As the average grain size increases,the number of transgranular contacts with higher bonding strength in the region connecting both loading points increases.The number of high-strength force chains increases,leading to an increase in the stress concentration value required for the macroscopic failure of the sample.Due to the highest bonding strength,the generation of transgranular cracks in quartz requires a higher concentrated stress value.With increasing volume composition of quartz,the number of transgranular cracks in quartz distributed in the region connecting both loading points increases,which requires many high-strength force chains.The load level rises,leading to an increase in the tensile strength of the numerical sample.

The quaternion beam model for hard-magnetic flexible cantilevers

The recently developed hard-magnetic soft(HMS)materials manufactured by embedding high-coercivity micro-particles into soft matrices have received considerable attention from researchers in diverse fields,e.g.,soft robotics,flexible electronics,and biomedicine.Theoretical investigations on large deformations of HMS structures are significant foundations of their applications.This work is devoted to developing a powerful theoretical tool for modeling and computing the complicated nonplanar deformations of flexible beams.A so-called quaternion beam model is proposed to break the singularity limitation of the existing geometrically exact(GE)beam model.The singularity-free governing equations for the three-dimensional(3D)large deformations of an HMS beam are first derived,and then solved with the Galerkin discretization method and the trustregion-dogleg iterative algorithm.The correctness of this new model and the utilized algorithms is verified by comparing the present results with the previous ones.The superiority of a quaternion beam model in calculating the complicated large deformations of a flexible beam is shown through several benchmark examples.It is found that the purpose of the HMS beam deformation is to eliminate the direction deviation between the residual magnetization and the applied magnetic field.The proposed new model and the revealed mechanism are supposed to be useful for guiding the engineering applications of flexible structures.

3D Modeling and Simulation of Fancy Fabrics in Weft Knitting

Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper, 3D loop geometrical models of weft knitted fancy structures, including tuck stitch, jacquard stitch, transfer stitch and fleecy stitch, were developed based on an improved model of plain loop, and their central axes as some 3D space curves were achieved by using Non-Uniform Rational B-Splines (NURBS). The 3D visual simulation programme was written in C++ programming language using OpenGL, which was a function library of 3D graphics. Some examples of weft knitted fancy fabrics were generated and practical application of 3D simulation was discussed.

Spatiotemporal model of open-pit based on 3-D deposit model

A new method was put forward to make up the three-dimensional deposit model, and the spatiotemporal models of open-pit with temporal dynamics were also studied combined with the corrected models of multilevel ground states so as to bring the three-dimensional open-pit model at different time and its model serial formed from the evolvement into the management of temporal dimension in order to realize the spatial three-dimension and temporal dynamic for the mining management in open-pits,which makes this model easy to query and analyze 3-D information, also help surface mining replaying and stope evolution forecasting. Finally, the time-spatial model was established to show the dynamic mining on some open-pit under the windows XP and VC++ environment.

3D modeling of Unmanned Aerial Vehicles Tilt Photogrammetry

Unmanned Aerial Vehicles(UAV)tilt photogrammetry technology can quickly acquire image data in a short time.This technology has been widely used in all walks of life with the rapid development in recent years especially in the rapid acquisition of high-resolution remote sensing images,because of its advantages of high efficiency,reliability,low cost and high precision.Fully using the UAV tilt photogrammetry technology,the construction image progress can be observed by stages,and the construction site can be reasonably and optimally arranged through three-dimensional modeling to create a civilized,safe and tidy construction environment.

Deep3DSketch-im:rapid high-fidelity AI 3D model generation by single freehand sketches

The rise of artificial intelligence generated content(AIGC)has been remarkable in the language and image fields,but artificial intelligence(AI)generated three-dimensional(3D)models are still under-explored due to their complex nature and lack of training data.The conventional approach of creating 3D content through computer-aided design(CAD)is labor-intensive and requires expertise,making it challenging for novice users.To address this issue,we propose a sketch-based 3D modeling approach,Deep3DSketch-im,which uses a single freehand sketch for modeling.This is a challenging task due to the sparsity and ambiguity.Deep3DSketch-im uses a novel data representation called the signed distance field(SDF)to improve the sketch-to-3D model process by incorporating an implicit continuous field instead of voxel or points,and a specially designed neural network that can capture point and local features.Extensive experiments are conducted to demonstrate the effectiveness of the approach,achieving state-of-the-art(SOTA)performance on both synthetic and real datasets.Additionally,users show more satisfaction with results generated by Deep3DSketch-im,as reported in a user study.We believe that Deep3DSketch-im has the potential to revolutionize the process of 3D modeling by providing an intuitive and easy-to-use solution for novice users.

Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure(EWP). By means of a threedimensional(3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system(TDS) widely used in China and its optimized drainage system(ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice,including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 k Pa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.

Spatial distribution modeling of subsurface bedrock using a developed automated intelligence deep learning procedure:A case study in Sweden

Due to associated uncertainties,modelling the spatial distribution of depth to bedrock(DTB) is an important and challenging concern in many geo-engineering applications.The association between DTB,the safety and economy of design structures implies that generating more precise predictive models can be of vital interest.In the present study,the challenge of applying an optimally predictive threedimensional(3D) spatial DTB model for an area in Stockholm,Sweden was addressed using an automated intelligent computing design procedure.The process was developed and programmed in both C++and Python to track their performance in specified tasks and also to cover a wide variety of diffe rent internal characteristics and libraries.In comparison to the ordinary Kriging(OK) geostatistical tool,the superiority of the developed automated intelligence system was demonstrated through the analysis of confusion matrices and the ranked accuracies of different statistical errors.The re sults showed that in the absence of measured data,the intelligence models as a flexible and efficient alternative approach can account for associated uncertainties,thus creating more accurate spatial 3D models and providing an appropriate prediction at any point in the subsurface of the study area.

3D Analysis and Investigation of Traffic Noise Impact from Hemmat Highway Located in Tehran on Buildings and Surrounding Areas

This study analyzes and investigates the impact of traffic noise on high rise buildings and surrounding areas by the side of Hemmat Highway that links west of Tehran to the east. In this study, a 3D traffic noise simulation model is applied on a GIS system. Visualized noise levels are formulated by the proposed model for noise mapping on all surfaces of the buildings and surrounding ground in a 3D platform. The investigation shows that there is a high traffic noise impact on the foreground and front facades of buildings, rendering these areas unsuitable for residential purposes. The ground area by the sides of buildings and the building side panels receive a lower noise impact. Most of these areas are still not acceptable for residential and even commercial use, only the back yards and back panels, have the lowest traffic noise impact. It also shows that the building height is not an effective factor for reducing motorway noise on the upper part of the building. Finally, construction cantilever barriers with a height of seven meters, close to the outer edge of the highway was presented as an effective way to reduce noise within the allowable range of noise pollution for commercial and residential purposes.

3D Vector Reconstruction of the Typical Cervical Vertebra from Anatomical Sections of Korean Visible Human at the Laboratory of Clinical and Digital Anatomy of Paris Descartes University

Aim: To carry out a 3D vector reconstruction of the typical cervical vertebra from anatomical sections of the “Korean Visible Human” for educational purposes. Material and Methods: The anatomical subject was a 33-year-old Korean man who died of leukemia. He was 164 cm tall and weighed 55 kg. This man donated his body to science. Her body was frozen and cut into several anatomical sections after an MRI and CT scan. These anatomical sections were made using a special saw called a 0.2 mm thick cryomacrotome. Thus 8100 cuts were obtained. Only the sections numbered 940 to 1200 were used for our study. A segmentation by manual contouring of the different parts of the typical cervical vertebra was made using the software Winsurf version 3.5 on a laptop PC running Windows 7 equipped with a Ram of 8 gigas. Results: Our 3D vector model of the typical cervical vertebra is easily manipulated using the Acrobat 3DPDF interface. Each part of the vertebra accessible in a menu can be displayed, hidden or made transparent, and 3D labels are available as well as educational menus for learning anatomy. Conclusion: This original work constitutes a remarkable educational tool for the anatomical study of the typical cervical vertebra and can also be used as a 3D atlas for simulation purposes for training in therapeutic gestures.

Stochastic analysis of excavation-induced wall deflection and box culvert settlement considering spatial variability of soil stiffness

In this study, a three-dimensional (3D) finite element modelling (FEM) analysis is carried out to investigate the effects of soil spatial variability on the response of retaining walls and an adjacent box culvert due to a braced excavation. The spatial variability of soil stiffness is modelled using a variogram and calibrated by high-quality experimental data. Multiple random field samples (RFSs) of soil stiffness are generated using geostatistical analysis and mapped onto a finite element mesh for stochastic analysis of excavation-induced structural responses by Monte Carlo simulation. It is found that the spatial variability of soil stiffness can be described by an exponential variogram, and the associated vertical correlation length is varied from 1.3 m to 1.6 m. It also reveals that the spatial variability of soil stiffness has a significant effect on the variations of retaining wall deflections and box culvert settlements. The ignorance of spatial variability in 3D FEM can result in an underestimation of lateral wall deflections and culvert settlements. Thus, the stochastic structural responses obtained from the 3D analysis could serve as an effective aid for probabilistic design and analysis of excavations.

3D finite element analysis of a two-surface wear model in fretting tests

This article aims at developing a computationally efficient framework to simulate the erosion of two contact surfaces in three-dimensional(3D),depending on the body resistance.The framework involves finite element(FE)resolution of a fretting problem,wear computation via a non-local criterion including a wear distribution parameter(WDP),as well as updating of the geometry and automatic remeshing.Its originality is based on the capability to capture the damage on each surface and obtain local and global results for a quantitative and qualitative analysis.Numerical simulations are carried out for two 3D contact specimens with different values of WDP.The results highlight the importance of correctly modelling wear:One-surface wear model is sufficient from a global point of view(wear volume),or whenever the wear resistance for a body is much higher than that of another one,whereas a 3D two-surface wear model is essential to capturing local effects(contact pressure,wear footprint,etc.)related to the difference in wear resistance of the bodies.

Evaluation of earthquake impact on magnitude of the minimum principal stress along a shotcrete lined pressure tunnel in Nepal

In situ stress condition in rock mass is influenced by both tectonic activity and geological environment such as faulting and shearing in the rock mass.This influence is of significance in the Himalayan region,where the tectonic movement is active,resulting in periodic dynamic earthquakes.Each large-scale earthquake causes both accumulation and sudden release of strain energy,instigating changes in the in situ stress environment in the rock mass.This paper first highlights the importance of the magnitude of the minimum principal stress in the design of unlined or shotcrete lined pressure tunnel as water conveyance system used for hydropower schemes.Then we evaluated the influence of local shear faults on the magnitude of the minimum principal stress along the shotcrete lined high pressure tunnel of Upper Tamakoshi Hydroelectric Project(UTHP)in Nepal.A detailed assessment of the in situ stress state is carried out using both measured data and three-dimensional(3D)numerical analyses with FLAC3D.Finally,analysis is carried out on the possible changes in the magnitude of the minimum principal stress in the rock mass caused by seismic movement(dynamic loading).A permanent change in the stress state at and nearby the area of shear zones along the tunnel alignment is found to be an eminent process.

Revolutionizing preclinical research for pancreatic cancer:the potential of 3D bioprinting technology for personalized therapy

Pancreatic cancer(PC)is a prevalent digestive malignancy worldwide and ranks as the fourth leading cause of cancer-related deaths globally.The incidence and mortality rates have been increasing annually,and due to its insidious onset and high malignancy,most patients are diagnosed at an advanced stage,with a 5-year survival rate of less than 8%(1).PC can be classified into endocrine and exocrine tumors,with over 95% of pancreatic malignant tumors originating from the exocrine portion of the pancreas.

倾斜摄影测量技术在福建农村三维地籍与房屋调查工作中的应用

探索了倾斜摄影测量技术在三维地籍测量与调查中的应用,分析了倾斜摄影测量技术较之传统测量技术所具有的优势,提出了倾斜摄影测量技术具有快速进行数据采集、直接生产三维模型、获得丰富的多源成果等特点,指出了倾斜摄影测量是实现三维地籍管理的有效手段。

“中心岛法”斜支撑基坑开挖坡比探讨

采用三维有限元分析方法，对武汉某基坑“中心岛法”开挖施工过程进行了模拟，分析了开挖过程中支护结构水平位移和基坑周边地表沉降的变化过程，为基坑初步设计和优化设计提供了参考。在同一地层和支护布设情况下，采用不同坡比开挖对基坑支护结构水平位移及周边地表沉降的影响进行了研究，研究结果表明：随着斜坡开挖坡度的增加，斜坡开挖前后支护结构水平位移和基坑周边沉降不断增加，且增大的幅度越来越大；针对不同的基坑场地和周边环境情况，选取合理的斜坡坡比，对控制基坑开挖对周边环境的影响以及缩短基坑工期等有很好的作用，从基坑安全性和工期两方面综合考虑得出武汉一级阶地两层地下室及以下基坑较合适的开挖坡比为1：1．0～1：1．5。

芳纶三维编织复合材料的抗冲击性能研究

用三维纺织结构复合材料的纤维倾斜模型在准细观结构层次上分解三维编织复合材料 ,建立与三维编织复合材料具有相同纤维体积含量的单向板细观模型。用动态显式算法有限元程序模拟倾斜单向板弹道侵彻破坏过程 ,并得到弹体贯穿靶体后的剩余速度和靶体变形形态。计算结果与弹道测试结果的比较证明在三维编织复合材料细观结构简化方案基础上计算三维编织复合材料弹道冲击性能的有效性。

3D printing of glass by additive manufacturing techniques:a review

Additive manufacturing(AM),which is also known as three-dimensional(3D)printing,uses computer-aided design to build objects layer by layer.Here,we focus on the recent progress in the development of techniques for 3D printing of glass,an important optoelectronic material,including fused deposition modeling,selective laser sintering/melting,stereolithography(SLA)and direct ink writing.We compare these 3D printing methods and analyze their benefits and problems for the manufacturing of functional glass objects.In addition,we discuss the technological principles of 3D glass printing and applications of 3D printed glass objects.This review is finalized by a summary of the current achievements and perspectives for the future development of the 3D glass printing technique.