Development of Temperature-Humidity Independent Control Air-Conditioning Unit for Residential Buildings

Cooling panels are increasingly used in domestic residential buildings.To provide medium temperature cold water for the cooling panel,and dehumidify the indoor air simultaneously,a new kind of temperature-humidity independent control air-conditioning unit was developed for single residential house by utilizing multi-variable technology.First,the supply air temperature was studied to determine the proper supply air flow rate for the humidity control.Then,the energy consumption of different temperature-humidity independent control systems was studied.The analysis indicates that unity evaporating temperature can be used to handle the moisture load and sensible heat load in two evaporators.So the unit scheme was put forward.Two evaporators were used to produce medium temperature water and dry air separately,and electric expansion valves were used to control the refrigerant distribution between the two evaporators.Then,experimental work was carried out to investigate the influence of compressor frequency,refrigerant distribution on the dehumidification capacity,energy efficiency and refrigeration capacity.In the end,the paper concludes that both compressor frequency and refrigerant distribution can control the dehumidification capacity,but the former influences the EER more than the latter,while the latter influences the refrigeration capacity more than the former.We can find a proper running point at certain sensible and latent cooling load by adjusting both compressor frequency and electric expansion valve.The energy consumption of this kind of unit was estimated and compared with present room air conditioners,which shows that it can save about 41% cooling energy consumption.

MPC-based Torque Distribution for Planar Motion of Four-wheel Independently Driven Electric Vehicles:Considering Motor Models and Iron Losses

The most critical obstacle for four-wheel independently driven electric vehicles(4WID-EVs)is the driving range.Being the actuators of 4WID-EVs,motors account for its major power consumption.In this sense,by properly distributing torques to minimize the power consumption,the driving range of 4WID-EV can be effectively improved.This paper proposes a model predictive control(MPC)-based torque distribution scheme,which minimizes the power consumption of 4WID-EVs while guaranteeing its tracking performance of planar motions.By incorporating the motor model considering iron losses,the optimal torque distribution can be achieved without an additional torque controller.Also,for this reason,the proposed control scheme is computationally efficient,since the power consumption term to be optimized,which is expressed as the product of the motor voltages and currents,is much simpler than that derived from the efficiency map.With reasonable simplification and linearization,the MPC problem is converted to a quadratic programming problem,which can be solved efficiently.The simulation results in MATLAB and CarSim co-simulation environments demonstrate that the proposed scheme effectively reduces power consumption with guaranteed tracking performance.

Research on Vehicle Control Technology Using Four-Wheel Independent Steering System

The enhancement of vehicle handling stability and maneuverability through active and independent rear wheels control is presented. Firstly, the configuration of four-wheel independent steering prototype vehide is introduced briefly. Then the concrete overall design of the electronic controllers of four wheel independent steering system （4WIS） is formulated in details. Under the control strategy of zero sideslip angle at mass center, the mathematical model of 4WIS is established to deduce the equations of separated rear wheel steering angles. According to these equations, simulation analysis for 4WIS vehicle performances is finished to show that 4WIS vehicle can improve the maneuverability greatly at low speed and increase the handling stability at high speed. Finally, the road test of 4WIS vehide has performed to verify the correctness of simulation and show that compared with the conventional four wheel steering （4WS） vehicle, the 4WIS vehicle not only improves the kinematical harmony but also decreases steering resistance and lighten abrasion of tires.

Investigation into the Independent Metering Control Performance of a Twin Spools Valve with Switching Technology-controlled Pilot Stage

In hydraulic area,independent metering control(IMC)technology is an effective approach to improve system efficiency and control flexibility.In addition,digital hydraulic technology(DHT)has been verified as a reasonable method to optimize system dynamic performance.Integrating these two technologies into one component can combine their advantages together.However,few works focused on it.In this paper,a twin spools valve with switching technologycontrolled pilot stage(TSVSP)is presented,which applied DHT into its pilot stage while appending IMC into its main stage.Based on this prototype valve,a series of numerical and experiment analysis of its IMC performance with both simulated load and excavator boom cylinder are carried out.Results showed fast and robust performance of pressure and flow compound control with acceptable fluctuation phenomenon caused by switching technology.Rising time of flow response in excavator cylinder can be controlled within 200 ms,meanwhile,the recovery time of rod chamber pressure under suddenly changed condition is optimized within 250 ms.IMC system based on TSVSP can improve both dynamic performance and robust characteristics of the target actuator so it is practical in valve-cylinder system and can be applied in mobile machineries.

Autonomous Tracking Control for Four-Wheel Independent Steering Robot Based on Improved Pure Pursuit

Autonomous tracking control is one of the fundamental challenges in the field of robotic autonomous navigation,especially for future intelligent robots.In this paper,an improved pure pursuit control method is proposed for the path tracking control problem of a four-wheel independent steering robot.Based on the analysis of the four-wheel independent steering model,the kinematic model and the steering geometry model of the robot are established.Then the path tracking control is realized by considering the correlation between the look-ahead distance and the velocity,as well as the lateral error between the robot and the reference path.The experimental results demonstrate that the improved pure pursuit control method has the advantages of small steady-state error,fast response and strong robustness,which can effectively improve the accuracy of path tracking.

Delay-independent robust guaranteed-cost control for uncertain linear neutral systems

This article concerns the delay-independent guaranteed-cost control problem via memoryless state feedback for a class of neutral-type systems with structural uncertainty and a given quadratic cost function. New delay-independent conditions for the existence of the guaranteed-cost controller are presented in the term of LMIs. An algorithm involving optimization is proposed to design a controller achieving an optimal guaranteed-cost, such that, the system can be stabilized for all admissible uncertainties. A numerical example is provided to illustrate the feasibility of the proposed method.

An Integrated Control Framework for Torque Vectoring and Active Suspension System

Four-wheel independently driven electric vehicles(FWID-EV)endow a flexible and scalable control framework to improve vehicle performance.This paper integrates the torque vectoring and active suspension system(ASS)to enhance the vehicle’s longitudinal and vertical motion control performance.While the nonlinear characteristic of the tire model leads to a relatively heavier computational burden.To facilitate the controller design and ease the load,a half-vehicle dynamics system is built and simplified to the linear-time-varying(LTV)model.Then a model predictive controller is developed by formulating the objective function by comprehensively considering the safety,energy-saving and comfort requirements.The in-wheel motor efficiency and the power loss of tire slip are treated as optimization indices in this work to reduce energy consumption.Finally,the effectiveness of the proposed controller is verified through the rapid-control-prototype(RCP)test.The results demonstrate the enhancement of the energy-saving as well as comfort on the basis of vehicle stability.

CONTROLLABILITY OF DELAY DEGENERATE CONTROL SYSTEMS WITH INDEPENDENT SUBSYSTEMS

The controllability of delay degenerate differential control systems is discussed. Firstly, delay degenerate differential control system was transformed to be canonical form, and the connected terms were gotten rid of, had delay degenerate differential control systems with independent subsystems. For the general delay degenerate differnetial control systems, it was gotten that the necessary and sufficient condition of that they are controllable is that their reachable set is equal to the whole space. For the delay degenerate differential control systems with independent subsystems, it was gotten that the necessary and sufficient conditions of that they are controllable are that their reachable sets are equal to their corresponding subspaces. Then some algebra criteria were gotten. Finally, an example was given to illustrate the main results.

Control performance and energy saving of multi-level pressure switching control system based on independent metering control

Aiming at the problem of large energy consumption in hydraulic control system with large load and variable working conditions,based on the multi-level pressure switching control system(MPSCS),a multi-level pressure switching control system based on independent metering control is proposed combined with the independent metering control technology.The configuration principle of the system is given,the mathematical model of this system is established,and the control strategy of the system under 4 different working quadrants is put forward.Finally,the control performance and energy saving characteristics of the system are tested.The test results show that the switching of high and low pressure power supply has a certain effect on the response of step position and ramp position under impedance working condition.The displacement curves show slow climbing or abrupt change of ramp position,and the position accuracy is less than 1 mm.The multi-level pressure switching control system based on independent metering control can recover and store energy under the transcendence working conditions.The control accuracy is about 1 mm,and the energy recovery rate is about 70%~80%.

Simulation Analysis of Characteristics for Independent Metering Control System Based on Downstream Compensation

Aiming at the shortcomings of the separate meter in and separate meter out?hydraulic system, a new type of independent metering control system is proposed by referring to the principle of load-sensing system. The valve group unit in the system is designed, and the AMESim/Matlab cosimulation model of the component and system is established. The actuator speed control, energy consumption and anti-flow saturation characteristics of the system are discussed. The simulation result shows that the system proposed in this article can achieve?better performances.

Research on the Stability Control Strategy of Four-Wheel Independent Driving Electric Vehicle

In order to research stability of four-wheel independent driving (4WID) electric vehicle, a torque allocation method based on the tire longitudinal forces optimization distribution is adopted. There are two layers in the controller, which includes the upper layer and the lower layer. In the upper layer, according to the demand of the longitudinal force, PID controller is set up to calculate the additional yaw moment created by yaw rate and side-slip angle. In the lower layer, the additional yaw moment is distributed properly to each wheel limited by several constraints. Carsim is used to build up the vehicle model and MATLAB/Simulink is used to build up the control model and both of them are used to simulate jointly. The result of simulation shows that a torque allocation method based on the tire longitudinal forces optimization distribution can ensure the stability of the vehicle.

Lessons Learned from Practical Independent Verification and Validation Based on IEEE 1012

IEEE 1012 [1] describes the SDLC phase activities for software independent verification and validation (IV & V) for nuclear power plant in truly general and conceptual manner, which requires the upward and/or downward tailoring on its interpretation for practical IV & V. It contains crucial and encompassing check points and guidelines to analyze the design integrity, without addressing the formalized and the specific criteria for IV & V activities confirming the technical integrity. It is necessary to list up the inspection viewpoint via interpretation of the standard that is practical review points checking design consistency. For fruitful IV & V of Control Element Driving Mechanism Control System (CEDMCS) software for Yonggwang Nuclear Power Plant unit 3 & 4, the specific viewpoints and approach are necessary based on the guidelines of IEEE 1012 to enhance the system quality by considering the level of implementation of the theoretical and the practical IV & V. Additionally IV & V guideline of IEEE 1012 does not specifically provide the concrete measure considering the system characteristics of CEDMCS. This paper provides the seven (7) characteristic criteria for CEDMCS IV & V, and by applying these viewpoints, the design analysis such as function, performance, interface and exception, backward and forward requirement traceability analysis has been conducted. The requirement, design, implementation, and test phase were only considered for IV & V in this project. This article also provides the translation of code to map theoretical verification and validation into practical verification and validation. This paper emphasizes the necessity of the intensive design inspection and walkthrough for requirement phase to resolve the design faults because the IV & V of early phase of SDLC obviously contributes to find out most of critical design inconsistency. Especially for test phase IV & V, it is strongly recommended to prepare the test plan document which is going to be the basis for the test coverage selection and test strategy. This test plan document should be based on the critical characteristics of function and performance of CEDMCS. Also to guarantee the independency of V & V organization participating in this project, and to acquire the full package of design details for IV & V, the systematic approach and efforts with an aspect of management is highlighted among the participants.

液阻全桥网络负载口独立电液系统节能控制策略仿真

针对传统电液控制系统节流损失大、能耗高、效率低的问题,采用液阻全桥网络搭建了具有负载口独立控制特性的新型电液控制系统,详细研究了该系统在典型四象限负载下的节能控制策略。液阻全桥网络电液系统由5个二位二通比例阀组成,根据其具有的负载口独立控制特性,将系统归纳为传统三位四通、负载口独立和负载敏感3种控制模式。传统三位四通下,两负载口开度控制模拟三位四通进出口耦合形式;负载口独立模式下,采用一腔控制流量另一腔阀口全开的控制策略;负载敏感模式下,控制泵出口压力比进油腔压力高一个定值,从而实现负载敏感功能。在超越负载下,3种模式都使用流量再生回路进行节能控制。AMESim+Matlab联合仿真结果表明,与传统的三位四通模式相比,三位四通流量再生、负载口独立、负载口独立流量再生、负载敏感模式分别节能43.38%、65.27%、77.91%、83.58%。

基于刚度可调的气动位置伺服系统摩擦补偿控制

气动伺服系统的低刚度、低气源压强、流量易饱和等特性,导致系统在工作过程中能量耗散较大,系统易受摩擦影响,且补偿效果不明显。尤其是当系统的运动方向改变时,会产生明显的“平顶现象”,严重影响气动伺服系统的跟踪精度。采用负载口独立控制结构,消除因两腔耦合而导致的能量耗散,使系统流量特性尽可能地位于线性区间;针对气动系统中存在的摩擦中部分参数不确定,以及外界干扰、动态负载的不确定性,设计非线性自适应鲁棒控制方法;将系统的刚度调节与自适应鲁棒控制进行协同控制,提高气动位置伺服系统的动态性能。仿真和实验结果均表明:具有刚度调节的自适应鲁棒控制能够明显降低系统能量耗散,提高系统位置跟踪精度,有效改善摩擦引起的“平顶现象”。

具有变超越负载的液压调平系统负载口独立控制方法

液压调平系统平台回落过程中存在超越负载,且随着负载重心偏移和平台倾角变化,作用于支腿液压缸的负载力也会随之变化。传统液压系统中负载控制阀或平衡阀在平衡变超越负载时速度控制效果差,容易发生速度抖动。为解决这一问题,采用负载口独立控制技术,针对平台回落时液压缸存在的变超越负载工况,提出对液压调平系统中液压缸有杆腔进行压力控制,无杆腔进行流量控制的压力-流量复合控制方法,建立其数学模型,并进行AMESim和Simulink联合仿真验证。结果表明,在负载力发生突变时,液压缸有杆腔压力和无杆腔流量均可在0.2 s内恢复至控制值,平衡掉系统变超越负载的同时,能够满足系统的速度控制需求。

换热器面积对双蒸发温度空调系统性能影响的模拟研究

建立了双蒸发温度空调系统仿真模型来研究改变换热器面积对系统性能的影响。搭建了双蒸发温度空调系统实验台,在实验工况下改变压缩机频率(30~120 Hz)和送风量(400~1 000 m^(3)/h),得到空调机组总制冷量Q_(c)、总显热制冷量Q_(s)和显热比SHR,验证了所建模型精度。在模型中改变换热器面积(48盘管、60盘管、72盘管)进行系统运行调节范围的研究。结果表明:随着换热器面积的增加,系统Q_(c)、Q_(s)和SHR的调节范围在整体扩大,最大增幅分别为5.0%、13.8%、11.8%。当送风量为1 000 m^(3)/h,压缩机频率为30 Hz,换热器面积从48盘管增至60盘管、72盘管时,Q_(s)的增幅分别为9.8%和13.8%,表明换热器面积增至60盘管时Q_(s)增长效果显著,再增加换热器面积,Q_(s)虽有所增大但增幅放缓。最后提出一种以所需制冷量为目标,依据环境温湿度调节范围设计换热器面积的方法。

中国潜在自主可控关键产品识别与突破路径研究

系统分析中国潜在自主可控关键产品突破时序路径,是逆全球化背景下全面防范和化解“卡脖子”潜在风险的关键。基于1995—2021年243个国家(地区)出口产品数据构建产品空间网络模型,识别全球核心产品及中国潜在自主可控关键产品,基于产品能力和网络核心性构建优先度指数,挖掘潜在自主可控关键产品突破路径。研究表明,在2021年核心度前10%的124种全球核心产品中,共有54种中国潜在自主可控关键产品,其突破路径为:充分利用机械与电力设备、基本金属制品、化工产品等领域已有的产品能力基础,优先突破光学显影和金属工艺等领域的基础关键产品,再进一步突破机械与电力设备、光学与医疗等精密仪器、塑料与橡胶制品业等领域高端关键产品。

面向2G~5G通信的双频双极化基站天线设计

为满足多种通信制式融合的无线通信需求,提出一款覆盖2G、3G、LTE、Sub-6 GHz波段的交叉偶极子基站天线。2对呈±45°正交的偶极子用以实现天线的双极化特性,辐射单元中的扇形内环、钻石状的外环分别对应天线要实现的低频以及高频波段,可以通过对内环以及外环结构参数的调整实现对2个频段的独立控制。天线上方的寄生贴片用以优化天线阻抗匹配。通过制作实物,测得天线在2个频段分别具有49.9%(1.70~2.80 GHz)和19.2%(3.20~3.88 GHz)的相对带宽,隔离度整体优于20 dB,主视轴的交叉极化比优于21 dB,2个波段的半功率波束宽分别为66°±5°、78°±6°。与已有研究比较,该天线结构简单,在交叉极化和增益方面具有显著优势。

复杂地形六轮独立驱动与转向机器人轨迹跟踪与避障控制

为研究六轮移动机器人在复杂地形的运动控制方法,针对六轮独立驱动与转向机器人复杂地形轨迹跟踪问题,提出一种预测控制和动态补偿的控制方法。基于非完整约束的线性六轮移动机器人运动学模型,以模型预测控制算法为基础,引入比例-积分-微分补偿控制器,抑制动态滞后引起的跟踪误差,设计速度与转向角动态反馈补偿,以应对地形扰动对轨迹跟踪的影响。分析机器人运动过程中障碍物的避碰问题,设计可求解避障轨迹的避障规划器,通过轨迹跟踪系统对局部避障轨迹进行跟踪控制,实现机器人的轨迹跟踪和自动避碰。对轨迹跟踪算法和避障算法进行仿真实验。实验结果表明:在典型工况下,机器人可完成凹形斜坡、凸形斜坡和凹凸地形正弦型轨迹跟踪控制和静态与动态障碍物避碰,验证了新方法的有效性。