Numerical Simulation of the Impact of Vegetation Index on the Interannual Variation of Summer Precipitation in the Yellow River Basin

Two sets of numerical experiments using the coupled National Center for Environmental Prediction General Circulation Model （NCEP/GCM T42L18） and the Simplified Simple Biosphere land surface scheme （SSiB） were carried out to investigate the climate impacts of fractional vegetation cover （FVC） and leaf area index （LAI） on East Asia summer precipitation, especially in the Yellow River Basin （YRB）. One set employed prescribed FVC and LAI which have no interannual variations based on the climatology of vegetation distribution; the other with FVC and LAI derived from satellite observations of the International Satellite Land Surface Climate Project （ISLSCP） for 1987 and 1988. The simulations of the two experiments were compared to study the influence of FVC, LAI on summer precipitation interannual variation in the YRB. Compared with observations and the NCEP reanalysis data, the experiment that included both the effects of satellite-derived vegetation indexes and sea surface temperature （SST） produced better seasonal and interannual precipitation variations than the experiment with SST but no interannual variations in FVC and LAI, indicating that better representations of the vegetation index and its interannual variation may be important for climate prediction. The difference between 1987 and 1988 indicated that with the increase of FVC and LAI, especially around the YRB, surface albedo decreased, net surface radiation increased, and consequently local evaporation and precipitation intensified. Further more, surface sensible heat flux, surface temperature and its diurnal variation decreased around the YRB in response to more vegetation. The decrease of surface-emitting longwave radiation due to the cooler surface outweighed the decrease of surface solar radiation income with more cloud coverage, thus maintaining the positive anomaly of net surface radiation. Further study indicated that moisture flux variations associated with changes in the general circulation also contributed to the precipitation interannual variation.

Improved Land Use and Leaf Area Index Enhances WRF-3DVAR Satellite Radiance Assimilation： A Case Study Focusing on Rainfall Simulation in the Shule River Basin during July 2013

The application of satellite radiance assimilation can improve the simulation of precipitation by numerical weather prediction models. However, substantial quantities of satellite data, especially those derived from low-level（surface-sensitive）channels, are rejected for use because of the difficulty in realistically modeling land surface emissivity and energy budgets.Here, we used an improved land use and leaf area index（LAI） dataset in the WRF-3 DVAR assimilation system to explore the benefit of using improved quality of land surface information to improve rainfall simulation for the Shule River Basin in the northeastern Tibetan Plateau as a case study. The results for July 2013 show that, for low-level channels（e.g., channel 3）,the underestimation of brightness temperature in the original simulation was largely removed by more realistic land surface information. In addition, more satellite data could be utilized in the assimilation because the realistic land use and LAI data allowed more satellite radiance data to pass the deviation test and get used by the assimilation, which resulted in improved initial driving fields and better simulation in terms of temperature, relative humidity, vertical convection, and cumulative precipitation.

Comparison of delay compensation methods for real-time hybrid simulation using frequency-domain evaluation index

The delay compensation method plays an essential role in maintaining the stability and achieving accurate real-time hybrid simulation results. The effectiveness of various compensation methods in different test scenarios, however, needs to be quantitatively evaluated. In this study, four compensation methods （i.e., the polynomial extrapolation, the linear acceleration extrapolation, the inverse compensation and the adaptive inverse compensation） are selected and compared experimentally using a frequency evaluation index （FEI） method. The effectiveness of the FEI method is first verified through comparison with the discrete transfer fimction approach for compensation methods assuming constant delay. Incomparable advantage is further demonstrated for the FEI method when applied to adaptive compensation methods, where the discrete transfer function approach is difficult to implement. Both numerical simulation and laboratory tests with predefined displacements are conducted using sinusoidal signals and random signals as inputs. Findings from numerical simulation and experimental results demonstrate that the FEI method is an efficient and effective approach to compare the performance of different compensation methods, especially for those requiring adaptation of compensation parameters.

Using Crop Management Scenario Simulations to Evaluate the Sensitivity of the Ohio Phosphorus Risk Index

Phosphorus (P) risk indices are commonly used in the USA to estimate the field-scale risk of agricultural P runoff. Because the Ohio P Risk Index is increasingly being used to judge farmer performance, it is important to evaluate weighting/scoring of all P Index parameters to ensure Ohio farmers are credited for practices that reduce P runoff risk and not unduly penalized for things not demonstrably related to runoff risk. A sensitivity analysis provides information as to how sensitive the P Index score is to changes in inputs. The objectives were to determine 1) which inputs are most highly associated with P Index scores and 2) the relative impact of each input variable on resultant P Index scores. The current approach uses simulations across 6134 Ohio point locations and five crop management scenarios (CMSs), representing increasing soil disturbance. The CMSs range from all no-till, which is being promoted in Ohio, rotational tillage, which is a common practice in Ohio to full tillage to represent an extreme practice. Results showed that P Index scores were best explained by soil test P (31.9%) followed by connectivity to water (29.7%), soil erosion (13.4%), fertilizer application amount (11.3%), runoff class (9.5%), fertilizer application method (2.2%), and finally filter strip (2.0%). Ohio P Index simulations across CMSs one through five showed that >40% scored <15 points (low) while <1.5% scored >45 points (very high). Given Ohio water quality problems, the Ohio P Index needs to be stricter. The current approach is useful for Ohio P Index evaluations and revision decisions by spatially illustrating the impact of potential changes regionally and state-wide.

Deformation warning index for reinforced concrete dam based on structural health monitoring data and numerical simulation

The material mechanical parameters of the dam body and foundation will change when a dam is reinforced during the aging process.This causes significant changes in the structural state of the project and makes it difficult to ensure its structural safety.In this study,a new deformation warning index for reinforced concrete dams was developed according to the prototype monitoring data,statistical models,three-dimensional finite element model(FEM)numerical simulation,and the critical conditions of the dam structure.A statistical model was established to separate the water pressure component.Then,a three-dimensional FEM of the reinforced concrete dam was constructed to simulate the water pressure component.Furthermore,the deformation components that affected the mechanical parameters of the dam under the same amount of reservoir water level change were separated and quantified accurately.In addition,the method for inversion of comprehensive mechanical parameters after dam reinforcement was used.The influence mechanisms of the deformation behavior of concrete dams under the reservoir water level and temperature changes were investigated.A new deformation warning index was developed by combining the forward-simulated critical water pressure component and temperature component in the period of extreme temperature decrease with the aging component separated by the statistical model.The new deformation warning index considers the structural state of the dam before and after reinforcement and links the structural strength criterion and the deformation evolution mechanisms.It provides a theoretical foundation and decision support for long-term service and operation management of reinforced dams.

Monte Carlo Simulation on LED Graded-refractive-index Multilayer Encapsulation Structure

Light propagation in nanoparticle-loaded encapsulants is simulated based on the method of Monte Carlo,referring to the multilayer graded-refractive-index structure for LED encapsulants.And the influence of scattering coefficient on the transmittance is analyzed.The results show that the transmittance decreases with scattering coefficient.For a given number of layers,the encapsulants will yield maximum transmittance if the refractive index value of each layer is optimized.The nanoparticle-loaded encapsulant consists of multiple layers with refractive-index values that gradually decrease.The transmittance will be higher than that of traditional non-graded encapsulants,and will improve light extraction efficiency of LED.

Sensitivity Analysis and Selection of Check Index of Signal Intersection Simulation Model Based on VISSIM

Selecting check index quantitatively is the core of the calibration of micro traffic simulation parameters at signal intersection. Five indexes in the node (intersection) module of VISSIM were selected as the check index set. Twelve simulation parameters in the core module were selected as the simulation parameters set. Optimal process of parameter calibration was proposed and model of the intersection of Huangcun west street and Xinghua street in Beijing was built in VISSIM to verify it. The sensitivity analysis between each check index and simulation parameter in their own set was conducted respectively. Sensitive parameter sets of different check indices were obtained and compared. The results show that different indexes have different size of set, and average vehicle delay’s is maximum, so it’s necessary to select index quantitatively. The results can provide references for scientific selection of the check indexes and improve the study efficiency of parameter calibration.

Simulated Sample Behaviour of a Dissimilarity Index When Sampling from Populations Differing by a Location Parameter Only

In this paper the authors study empirically the power of the test based on the index of dissimilarity to compare two samples drawn from two populations differing only in the location parameter. We call such a test as test of homogeneity. In practice the power of such a bidirectional test will be studied referring to the absolute value of the shiftδand to the same probability models considered by Fried and Dehling.

Simulation of Growth and Leaf Area Index of Quality Protein Maize Varieties in the Southwestern Savannah Region of the DR-Congo

Logistic and exponential approaches have been used to simulate plant growth and leaf area index (LAI) in different growing conditions. The objective of the present study was to develop and evaluate an approach to simulate maize LAI that expresses key physiological and phonological processes using a minimum entry requirement for Quality Protein maize (QPM) varieties grown in the southwestern region of the DR-Congo. Data for the development and testing of the model were collected manually in experimental plots using a non-destructive method. Simulation results revealed measurable variations between crop seasons (long season A and short season B) and between the two varieties (Mudishi-1 and Mudishi-3) for height, number of visible leaves, and LAI. For both seasons, Mudishi-3, a short stature variety was associated with expected stable yield based on simulation data. In general, the model simulated reliably all the parameters including the LAI. The LAI value for mudishi-1 was higher than that of Mudishi-3. There were significant differences among the model parameters (K, Ti, a, b, Tf) and between the two varieties. In all crop conditions studied and for the two varieties, the senescence rate (a) was higher, while the growth rate (b) was lower compared to the estimates based on the STICS model.

Numerical Simulation of the Influence of Pore Structure on Resistivity, Formation Factor and Cementation Index in Tight Sandstone

Tight sandstone,with severe diagenesis and complex pore structure,differs greatly from conventional sandstone in terms of rock electrical parameters.In subsurface rock electrical experiments,various electrical parameters are confounded and can only be analyzed qualitatively.The lack of quantitative analysis for each individual electrical parameter presents a challenge for the evaluation of oil and gas saturation in tight sandstone.Based on the 2D pore-throat model and the features of pore structure in the tight sandstone of the Penglaizhen and Shaximiao Formations in the upper and middle Jurassic of the Western Sichuan Depression,this paper presents 3D micro pore-throat models for three types of tight sandstone.It proposes a finite element-based rock electrical simulation method to analyze the influence of pore structure parameters,such as throat radius and throat tortuosity,on electrical parameters such as resistivity,formation factor,and cementation index quantitatively.The research revealed the following results:(1)Throats of tight sandstone usually have lamellar or curved lamellar shapes that are slender and narrow.The lamellar throat used in the proposed porethroat model is more consistent with the features of tight sandstone than the tubular throat used in the original model.(2)The throat determines the conductivity of tight sandstone.The throat parallel to the electric potential has the greatest influence on conductivity,and the throat perpendicular to the potential has the least influence.(3)In tight sandstone grades I to III,as the porosity decreases,the formation factor increases and the cementation index decreases.(4)The results of the rock electrical simulation are consistent with the results of the rock electrical experiment,which indicates that the proposed rock electrical simulation method of tight sandstone is effective and accurate.

Growth and Leaf Area Index Simulation in Maize(Zea mays L.)under Small-Scale Farm Conditions in a Sub-Saharan African Region

Different crop models including MAIZE Ceres, STICS and other approaches have been used to simulate leaf area index (LAI) in maize (Zea mays L.). These modeling tools require genotype-specific calibration procedures. Studies on modeling LAI dynamics under optimal growth conditions with yields close to the yield potential have remained scarce. In the present study, logistic and exponential approaches have been developed and evaluated for the simulation of LAI in maize in a savannah region of the DR-Congo. Data for the development and the evaluation of the model were collected manually by non-destructive method from small farmers’ field. The rate of expansion of the leaf surface and the rate of change of leaf senescence were also simulated. There were measurable variations among sites and varieties for the simulated height of maize plants. At all sites, the varieties with short plants were associated with expected superior performance based on simulation data. In general, the model underestimates the LAI based on observed values. LAI values for the genetically improved maize varieties (Salongo 2, MUS and AK) were greater than those of the unimproved local variety (Local). There were significant differences for K, b, Ti, LAI, Tf, and parameters among models and varieties. In all sites and for all varieties, the growth rate (b) was higher, while the rate of senescence (a) was lower compared to STICS estimates.

弧面分度凸轮机构动力学建模与Simulink仿真技术的研究

对弧面分度凸轮机构动力学特性进行了研究,考虑间隙存在、柔性轴和电机特性下,建立了系统动力学方程,应用Matlab/Simulink求解和动态仿真。结果显示间隙对凸轮和工作盘的响应有影响,从动件最大角加速度提高28%,电机输出轴角速度高频振荡。

Dynamic Monitoring of Plant Cover and Soil Erosion Using Remote Sensing, Mathematical Modeling, Computer Simulation and GIS Techniques

Dynamic monitoring of plant cover and soil erosion often uses remote sensing data, especially for estimating the plant cover rate (vegetation coverage) by vegetation index. However, the latter is influenced by atmospheric effects and methods for correcting them are still imperfect and disputed. This research supposed and practiced an indirect, fast, and operational method to conduct atmospheric correction of images for getting comparable vegetation index values in different times. It tries to find a variable free from atmospheric effects, e.g., the mean vegetation coverage value of the whole study area, as a basis to reduce atmospheric correction parameters by establishing mathematical models and conducting simulation calculations. Using these parameters, the images can be atmospherically corrected. And then, the vegetation index and corresponding vegetation coverage values for all pixels, the vegetation coverage maps and coverage grade maps for different years were calculated, i.e., the plant cover monitoring was realized. Using the vegetation coverage grade maps and the ground slope grade map from a DEM to generate soil erosion grade maps for different years, the soil erosion monitoring was also realized. The results show that in the study area the vegetation coverage was the lowest in 1976, much better in 1989, but a bit worse again in 2001. Towards the soil erosion, it had been mitigated continuously from 1976 to 1989 and then to 2001. It is interesting that a little decrease of vegetation coverage from 1989 to 2001 did not lead to increase of soil erosion. The reason is that the decrease of vegetation coverage was chiefly caused by urbanization and thus mainly occurred in very gentle terrains, where soil erosion was naturally slight. The results clearly indicate the details of plant cover and soil erosion change in 25 years and also offer a scientific foundation for plant and soil conservation.

Metamorphic Manipulating Mechanism Design for MCCB Using Index Reduced Iteration

The present research on moulded case circuit breaker（MCCB） focuses on the enhancement of current-limiting interrupting performance during short circuit, overload, under voltage and phase failure, involving electrics, magnetic, mechanics, thermal, material, friction, arc extinguishing, impact vibration, skin effect, etc. The rigid-flexible coupling of the parts and components of the metamorphic manipulating mechanism in multi-fields leads to the non-rigid, high frequency, high damping, singularity of the Euler-Lagrange equations which represents the multi-body dynamics. The small step iteration which is used for obtaining the instantaneous and short time critical interrupting performance of metamorphic mechanism appears inaccuracy. It is difficult to realize top-down design by existing CAD systems. Therefore, a metamorphic manipulating mechanism design method for MCCB using index reduced iteration（IRI） is put forward. The metamorphic manipulating mechanism of MCCB is decomposed into three mechanisms： main switch connector mechanism, electromagnet-drawbar-jump buckle mechanism, and bimetallic strip-drawbar mechanism, which is respectively described by electro-dynamic force, electromagnet force, and bimetallic strip force. The dummy part（virtual rigid） without moment of inertia and mass is employed as intermediate to join the flexible body and rigid body. The model of rigid-flexible coupling metamorphic mechanism multi-body dynamics is built. The differential algebraic equations（DAEs） of the multibody dynamics model are converted to pure ordinary differential equations（ODEs） by coordinate partition. Order reduced integration with multi-step and variable step-size is preceded based on IRI. The non-linear algebraic equations are solved in each integration step by Newton-Rapson iteration. There is no ill-condition and singularity of Jacobian matrix when step size reduces to zero. The independent prototype design system using ACIS R13, HOOPS V11.0 and Visual C＋＋.NET 2003 has been developed, which verifies the effectiveness of the proposed method. The proposed method enhances the current-limiting interrupting performance of MCCB, and has reference significance for multi-body dynamics design for similar flexible metamorphic mechanisms in multi-fields.

Deformation early-warning index for heightened gravity dam during impoundment period

The mechanical parameters of materials in a dam body and dam foundation tend to change when dams are reinforced in aging processes.It is important to use an early-warning index to reflect the safety status of dams,particularly of heightened projects in the impoundment period.Herein,a new method for monitoring the safety status of heightened dams is proposed based on the deformation monitoring data of a dam structure,a statistical model,and finite-element numerical simulation.First,a fast optimization inversion method for estimation of dam mechanical parameters was developed,which used the water pressure component extracted from a statistical model,an improved inversion objective function,and a genetic optimization iterative algorithm.Then,a finite element model of a heightened concrete gravity dam was established,and the deformation behavior of the dam with rising water levels in the impoundment period was simulated.Subsequently,mechanical parameters of aged dam parts were calculated using the fast optimization inversion method with simulated deformation and the water pressure deformation component obtained by the statistical model under the same conditions of water pressure change.Finally,a new earlywarning index of dam deformation was constructed by means of the forward-simulated deformation and other components of the statistical model.The early-warning index is useful for forecasting dam deformation under different water levels,especially high water levels.

The Suitability of Using Leaf Area Index to Quantify Soil Loss under Vegetation Cover

Soil erosion by water under forest cover is a serious problem in southern China.A comparative study was carried out on the use of leaf area index(LAI) and vegetation fractional coverage(VFC) in quantifying soil loss under vegetation cover.Five types of vegetation with varied LAI and VFC under field conditions were exposed to two rainfall rates(40 mm h-1 and 54 mm h-1) using a portable rainfall simulator.Runoff rate,sediment concentration and soil loss rate were measured at relatively runoff stable state.Significant negative exponential relationship(p < 0.05,R2 = 0.83) and linear relationship(p < 0.05,R2 = 0.84) were obtained between LAI and sediment concentration,while no significant relationship existed between VFC and sediment concentration.The mechanism by which vegetation canopy prevents soil loss was by reducing rainfall kinetic energy and sediment concentration.LAI could better quantify such a role than VFC.However,neither LAI nor VFC could explain runoff rate or soil loss rate.Caution must be taken when using LAI to quantify the role of certain vegetation in soil and water conservation.

Analysis and Simulation of Plant Type on Canopy Structure and Radiation Transmission in Rice

Three typical hybrid rice cultivars, together with three artificially modified plant types by the application of N fertilizer during the elongation of the two uppermost leaves were used to analyze how the plant type affected the layered leaf area and radiation transmission. Plant type factors, layered leaf area and radiation distribution were measured at the full heading, 10 d and 25 d after full heading stages, respectively. A model for calculating the layered leaf area from plant type factors was established and validated to determine the effects of plant type factors on the layered leaf area for the three hybrids. Furthermore, the relationship between layered leaf area and radiation transmission was established by using the radiation transmission model. The effects of the plant type factors on the radiation transmission for the three hybrids were evaluated by using this model. Finally, a method was established to describe the canopy structure, such as the layered leaf area index and the radiation distribution in the rice canopy.

The Profiling of International Roughness Index (IRI) Based on Lagrangian Method

The phenomenological equations of motion for the international roughness index (IRI) have been reviewed and discussed in terms of Lagrangian method in physics. The current paper proposes a practical, two-dimensional model for studying essentially three-dimensional, vibrating,?and?mechanical systems (vehicles). The purpose is to provide a new profiling method for IRI, which is practical in computations and compatible with traditional profiling for roughness of a road-surface. The modern technology employs elaborated sensors such as gyro sensor, Global Positioning System (GPS), magnetometer sensor,?and?accelerometer to measure high-speed longitudinal motions, resulting in time series of big-data expressed as compressed longitudinal spikes. The time series of longitudinal spikes obtained from high-speed longitudinal motions are traditionally considered as a background noise for constructing a profile. The conventional IRI is calculated from big-data of the road profile by employing statistical method, but the Lagrangian model dynamically determines the road profile. The useful concept and relation among the road-roughness function?, associated roughness index (ARI), acceleration and position are introduced and examined in the present paper. The associated roughness index (ARI) defined by the current dynamical approach is examined by applying virtual simulations which represent roughness of a road-surface. The current theoretical model supports and compensates information of interpreting a profile of IRI and elucidates physical meanings for the roughness index of a road-surface.

A modified method to calculate reliability index using maximum entropy principle

Routine reliability index method, first order second moment (FOSM), may not ensure convergence of iteration when the performance function is strongly nonlinear. A modified method was proposed to calculate reliability index based on maximum entropy (MaxEnt) principle. To achieve this goal, the complicated iteration of first order second moment (FOSM) method was replaced by the calculation of entropy density function. Local convergence of Newton iteration method utilized to calculate entropy density function was proved, which ensured the convergence of iteration when calculating reliability index. To promote calculation efficiency, Newton down-hill algorithm was incorporated into calculating entropy density function and Monte Carlo simulations (MCS) were performed to assess the efficiency of the presented method. Two numerical examples were presented to verify the validation of the presented method. Moreover, the execution and advantages of the presented method were explained. From Example 1, after seven times iteration, the proposed method is capable of calculating the reliability index when the performance function is strongly nonlinear and at the same time the proposed method can preserve the calculation accuracy; From Example 2, the reliability indices calculated using the proposed method, FOSM and MCS are 3.823 9, 3.813 0 and 3.827 6, respectively, and the according iteration times are 5, 36 and 10 6 , which shows that the presented method can improve calculation accuracy without increasing computational cost for the performance function of which the reliability index can be calculated using first order second moment (FOSM) method.

Quick System-Level DDR3 Signal Integrity Simulation Research

---Double data rate synchronous dynamic random access memory （DDR3） has become one of the most mainstream applications in current server and computer systems. In order to quickly set up a system-level signal integrity （SI） simulation flow for the DDR3 interface, two system-level SI simulation methodologies, which are board-level S-parameter extraction in the frequency-domain and system-level simulation assumptions in the time domain, are introduced in this paper. By comparing the flow of Speed2000 and PowerSI/Hspice, PowerSI is chosen for the printed circuit board （PCB） board-level S-parameter extraction, while Tektronix oscilloscope （TDS7404） is used for the DDR3 waveform measurement. The lab measurement shows good agreement between simulation and measurement. The study shows that the combination of PowerSI and Hspice is recommended for quick system-level DDR3 SI simulation.