The exergy analysis and finite time thermodynamic methods had been employed to analyze the compound condensation process (CCP). It was based on the air-cooling heat pump unit. The cooling capacity of the chiller unit ...The exergy analysis and finite time thermodynamic methods had been employed to analyze the compound condensation process (CCP). It was based on the air-cooling heat pump unit. The cooling capacity of the chiller unit is about 1 kW, and the work refrigerant is R22/R407C/R410A/CO2. The MATLAB/SIMULINK software was employed to build the simulation model. The thermodynamic simulation model is significant for the optimization of parameters of the unit, such as condensation and evaporation temperature and mass flow of the sanitary hot water and size of hot water storage tank. The COP of the CCP of R410A system is about 3% - 5% higher than the CCP of the R22 system, while CCP of the R407C system is a little lower than the CCP of R22 system. And the CCP of CO2 trans-critical system has advantage in the hot supply mode. The simulation method provided a theoretical reference for developing the production of CCP with substitute refrigerant R407C/R410A/CO2.展开更多
Given the distribution feature of resources such as coal and water, the requirements for the development of Chinese power industry, and the fact of monopoly by foreign companies, it is very necessary and significant t...Given the distribution feature of resources such as coal and water, the requirements for the development of Chinese power industry, and the fact of monopoly by foreign companies, it is very necessary and significant to independently research and develop air-cooling technologies. Through experimental research, simulative calculation, process and equipment development, field tests and a demonstration project, the design and operation technologies for air-cooling system are grasped and relevant key equipment is developed. The results of the demonstration project show that the technical indicators for the air-cooling system have met or exceeded the design requirements. Part of the research results have been incorporated into the relevant national design standards. The technologies developed have been applied to more than 23 sets of thermal power units of or above 600 MW in China.展开更多
Imaging department is an important department of a hospital contributing directly to patient care, providing diagnostic support to all specialties which cannot practice efficiently without their support. Hospital admi...Imaging department is an important department of a hospital contributing directly to patient care, providing diagnostic support to all specialties which cannot practice efficiently without their support. Hospital administrators are looking for newer tools to control costs without affecting the quality of patient care. It is well known that the escalation of costs for advanced technology has been dramatic and it has been labeled as one of the culprits for great increase in healthcare costs. A prospective study for a period of six months was carried out for calculation of unit cost of radiological investigations CT head, CT chest, CT abdomen and MRI. Unit costs were computed under direct and indirect costs. The actual cost incurred by the hospital on CT head was Rupees 581.40 (US $10.89), CT abdomen Rupees 2339.20 (US $43.83), CT chest Rupees 2339.20 (US $43.83), and MRI Rupees 4497.50 (US $84.28). However, in the hospital patients are charged Rupees 900 (US $16.86) for CT head, Rupees 1200 (US $22.48) for CT abdomen, Rupees 1200 (US $22.48) for CT chest and Rupees 2500 (US $46.85) for MRI. There is a substantial loss of revenue because of subsidies provided to patients in a tertiary care teaching hospital which needs revision of charges.展开更多
Both the modeling and the load regulation capacity prediction of a supercritical power plant are investigated in this paper. Firstly, an indirect identification method based on subspace identification method is propos...Both the modeling and the load regulation capacity prediction of a supercritical power plant are investigated in this paper. Firstly, an indirect identification method based on subspace identification method is proposed. The obtained identification model is verified by the actual operation data and the dynamic characteristics of the system are well reproduced. Secondly, the model is used to predict the load regulation capacity of thermal power unit. The power, main steam pressure, main steam temperature and other parameters are simulated respectively when the unit load is going up and down. Under the actual constraints, the load regulation capacity of thermal power unit can be predicted quickly.展开更多
文摘The exergy analysis and finite time thermodynamic methods had been employed to analyze the compound condensation process (CCP). It was based on the air-cooling heat pump unit. The cooling capacity of the chiller unit is about 1 kW, and the work refrigerant is R22/R407C/R410A/CO2. The MATLAB/SIMULINK software was employed to build the simulation model. The thermodynamic simulation model is significant for the optimization of parameters of the unit, such as condensation and evaporation temperature and mass flow of the sanitary hot water and size of hot water storage tank. The COP of the CCP of R410A system is about 3% - 5% higher than the CCP of the R22 system, while CCP of the R407C system is a little lower than the CCP of R22 system. And the CCP of CO2 trans-critical system has advantage in the hot supply mode. The simulation method provided a theoretical reference for developing the production of CCP with substitute refrigerant R407C/R410A/CO2.
文摘Given the distribution feature of resources such as coal and water, the requirements for the development of Chinese power industry, and the fact of monopoly by foreign companies, it is very necessary and significant to independently research and develop air-cooling technologies. Through experimental research, simulative calculation, process and equipment development, field tests and a demonstration project, the design and operation technologies for air-cooling system are grasped and relevant key equipment is developed. The results of the demonstration project show that the technical indicators for the air-cooling system have met or exceeded the design requirements. Part of the research results have been incorporated into the relevant national design standards. The technologies developed have been applied to more than 23 sets of thermal power units of or above 600 MW in China.
文摘Imaging department is an important department of a hospital contributing directly to patient care, providing diagnostic support to all specialties which cannot practice efficiently without their support. Hospital administrators are looking for newer tools to control costs without affecting the quality of patient care. It is well known that the escalation of costs for advanced technology has been dramatic and it has been labeled as one of the culprits for great increase in healthcare costs. A prospective study for a period of six months was carried out for calculation of unit cost of radiological investigations CT head, CT chest, CT abdomen and MRI. Unit costs were computed under direct and indirect costs. The actual cost incurred by the hospital on CT head was Rupees 581.40 (US $10.89), CT abdomen Rupees 2339.20 (US $43.83), CT chest Rupees 2339.20 (US $43.83), and MRI Rupees 4497.50 (US $84.28). However, in the hospital patients are charged Rupees 900 (US $16.86) for CT head, Rupees 1200 (US $22.48) for CT abdomen, Rupees 1200 (US $22.48) for CT chest and Rupees 2500 (US $46.85) for MRI. There is a substantial loss of revenue because of subsidies provided to patients in a tertiary care teaching hospital which needs revision of charges.
文摘Both the modeling and the load regulation capacity prediction of a supercritical power plant are investigated in this paper. Firstly, an indirect identification method based on subspace identification method is proposed. The obtained identification model is verified by the actual operation data and the dynamic characteristics of the system are well reproduced. Secondly, the model is used to predict the load regulation capacity of thermal power unit. The power, main steam pressure, main steam temperature and other parameters are simulated respectively when the unit load is going up and down. Under the actual constraints, the load regulation capacity of thermal power unit can be predicted quickly.