Heat transfer and temperature evolution in underground mininginduced overburden fracture and ground fissures: Optimal time window of UAV infrared monitoring

Heat transfer and temperature evolution in overburden fracture and ground fissures are one of the essential topics for the identification of ground fissures via unmanned aerial vehicle(UAV) infrared imager. In this study, discrete element software UDEC was employed to investigate the overburden fracture field under different mining conditions. Multiphysics software COMSOL were employed to investigate heat transfer and temperature evolution of overburden fracture and ground fissures under the influence of mining condition, fissure depth, fissure width, and month alternation. The UAV infrared field measurements also provided a calibration for numerical simulation. The results showed that for ground fissures connected to underground goaf(Fissure Ⅰ), the temperature difference increased with larger mining height and shallow buried depth. In addition, Fissure Ⅰ located in the boundary of the goaf have a greater temperature difference and is easier to be identified than fissures located above the mining goaf. For ground fissures having no connection to underground goaf(Fissure Ⅱ), the heat transfer is affected by the internal resistance of the overlying strata fracture when the depth of Fissure Ⅱ is greater than10 m, the temperature of Fissure Ⅱ gradually equals to the ground temperature as the fissures’ depth increases, and the fissures are difficult to be identified. The identification effect is most obvious for fissures larger than 16 cm under the same depth. In spring and summer, UAV infrared identification of mining fissures should be carried out during nighttime. This study provides the basis for the optimal time and season for the UAV infrared identification of different types of mining ground fissures.

Extraction of the key infrared radiation temperature features concerning stress and crack evolution of loaded rocks

The infrared radiation temperature(IRT)variation concerning stress and crack evolution of rocks is a critical focus in rock mechanics domain and engineering disaster warning.In this paper,a methodology to extract the key IRT features related to stress and crack evolution of loaded rocks is proposed.Specifically,the wavelet denoising and reconstruction in thermal image sequence(WDRTIS)method is employed to eliminate temporal noise in thermal image sequences.Subsequently,the adaptive partition temperature drift correction(APTDC)method is introduced to alleviate temperature drift.On this basis,the spatial noise correction method based on threshold segmentation and adaptive median filtering(OTSU-AMF)is proposed to extract the key IRT features associated with microcracks of loaded rocks.Following temperature drift correction,IRT provides an estimation of the thermoelastic factor in rocks,typically around 5.29×10^(-5) MPa^(-1) for sandstones.Results reveal that the high-temperature concentrated region in cumulative thermal images of crack evolution(TICE)can elucidate the spatiotemporal evolution of localized damage.Additionally,heat dissipation of crack evolution(HDCE)acquired from TICE quantifies the progressive failure process of rocks.The proposed methodology enhances the reliability of IRT monitoring results and provides an innovative approach for conducting research in rock mechanics and monitoring engineering disasters.

Calculation of the heat flux in the lower divertor target plate using an infrared camera diagnostic system on the experimental advanced superconducting tokamak

During the discharging of Tokamak devices, interactions between the core plasma and plasma-facing components (PFCs) may cause exorbitant heat deposition in the latter. This poses a grave threat to the lifetimes of PFCs materials. An infrared (IR) diagnostic system consisting of an IR camera and an endoscope was installed on an Experimental Advanced Superconducting Tokamak (EAST) to monitor the surface temperature of the lower divertor target plate (LDTP) and to calculate the corresponding heat flux based on its surface temperature and physical structure, via the finite element method. First, the temperature obtained by the IR camera was calibrated against the temperature measured by the built-in thermocouple of EAST under baking conditions to determine the true temperature of the LDTP. Next, based on the finite element method, a target plate model was built and a discretization of the modeling domain was carried out. Then, a heat conduction equation and boundary conditions were determined. Finally, the heat flux was calculated. The new numerical tool provided results similar to those for DFLUX;this is important for future work on related physical processes and heat flux control.

Study of Striated Heat Flux on EAST Divertor Plates Induced by LHW Using Infrared Camera

An upgraded infrared （IR） imaging system which provides a wide field of view （FOV） has been installed on the Experimental Advanced Superconducting Tokamak （EAST） to monitor the surface temperatures on plasma facing components. Modified magnetic topology induced by lower hybrid wave （LHW） can lead to the formation of striated heat flux （SHF} on divertor plates which can be clearly observed by IR camera. In this paper, LHW power modulation is applied to analyze the appearance of SHF. It is also demonstrated that deuterium （D） pellet injection and supersonic molecular beam injection （SMBI） can to some extent reduce the heat flux on the outer strike point （OSP）, but enhance the SHF on lower outer plates （LOP） of divertor. This may provide an optional approach to actively control the distribution of heat flux on diveror plates, which can protect materials from long duration high-heat flux.

Infrared Heating Technology for Automated Fiber Placement

Prepreg stickiness is the adhesion between prepregs or between a prepreg and a mold in lay-up process.It is critical for automated fiber placement,because the stickiness should be small for smooth transport,as well as large enough on the laying surface for a good placement performance.To ensure prepreg stickiness always being in the optimum laying window,placement temperature should be changed according to the laying speed.In our work,the relationship between laying speed and emissive power of heating lamp was studied.The heat transfer process between heating lamp and laying surface was analyzed and the control equation of dynamic temperature was derived.Finally,the infrared heating system was built and its effectiveness was verified based on placement experiment.

Characteristics of radiation and convection heat transfer in indirect near-infrared-ray heating chamber

Numerical study was performed to evaluate the characteristics of combined heat transfer of radiation, conduction and convection in indirect near infrared ray （N/R） heating chamber. The effects of important design parameters such as the shape of heat absorbing cylinder and heat releasing fin on the pressure drop and heat transfer coefficient were analyzed with different Reynolds numbers. The Reynolds numbers were varied from 103 to 3x106, which was defined based on the hydraulic diameter of the heat absorbing cylinder. Analyses were performed to obtain the inner and outer flow and the temperature distributions in the heat absorbing cylinder and the rates of radiation heat transfer and convection heat transfer. As the Reynolds number increases, the convection heat transfer rate is increased while the radiation heat transfer rate is decreased. The average convection heat transfer rate follows a power rule of the Reynolds number. Addition of three-dimensional heat releasing fin to the outside of the heat absorbing cylinder enhances the convection heat transfer.

Effect of preload force on heat generation of fatigue crack in ultrasonic infrared thermography

The heat generation behaviors of fatigue crack are deeply investigated under different preload forces combing numerical simulation and experiment.Firstly,a multi-contact simulation model is applied to stimulate the crack surfaces contact and the horn-sample contact under ultrasonic excitation for calculating the temperature fields.Then,the ultrasonic infrared thermography testing and the microscope testing are carried out for the heat generation and the plastic deformation behaviors of crack region under different preload forces.On this basis,an indirect observation method based on dots distribution is proposed to estimate the plastic deformation on crack contact surfaces.The obtained results show that the temperature rise of crack region increases with the increase of preload force when the preload force is less than 250 N,while the temperature rise rapidly declines due to the plastic deformation on crack contact surfaces and the inhibition effect when the preload force is 280 N.Moreover,the plastic deformation does not lead to the crack propagation,but reduces the detection repeatability of fatigue crack.This work provides an effective method for optimizing testing conditions in practical testing processes,which will be helpful to the establishment of testing standards for batches of test objects in ultrasonic infrared thermography testing.

Investigation on the plastic work-heat conversion coefficient of 7075-T651 aluminum alloy during an impact process based on infrared temperature measurement technology

The plastic work-heat conversion coefficient is one key parameter for studying the work-heat conversion under dynamic deformation of materials. To explore this coefficient of 7075-T651 aluminum alloy under dynamic compression, dynamic compression experiments using the Hopkinson bar under four groups of strain rates were conducted, and the temperature signals were measured by constructing a transient infrared temperature measurement system. According to stress versus strain data as well as the corresponding temperature data obtained through the experiments, the influences of the strain and the strain rate on the coefficient of plastic work converted to heat were analyzed.The experimental results show that the coefficient of plastic work converted to heat of 7075-T651 aluminum alloy is not a constant at the range of 0.85–1 and is closely related to the strain and the strain rate. The change of internal structure of material under high strain rate reduces its energy storage capacity, and makes almost all plastic work convert into heat.

Effects of Far-Infrared Irradiative Heating Pasteurization on Fungi

The effect of far-infrared (FIR) irradiation pasteurization on fungi was quantitatively evaluated and compared with the effect of thermal conductive heating. After the bulk temperature of the sterile saline irradiated by FIR reached a steady given temperature, yeast cells (Candida albicans NBRC 1950 and Saccharomyces cerevisiae NBRC 1067) or fungal spores (Aspergillus niger NBRC 4781) were inoculated and FIR heating was conducted. A mullite cylinder FIR heater, with a main wavelength of 4 - 7 μm, was used for FIR heating. Death of fungi by FIR heating and by thermal conductive heating both followed first-order reaction kinetics, and the apparent death rate constants under different temperature conditions were obtained. For the same bulk temperatures, pasteurization by FIR heating was more effective than thermal conductive heating. The activation energy for the death of fungi by FIR irradiation was slightly lower than thermal conductive heating, indicating differences in the mechanism of action.

Heat Source Analysis of Hard Disk Drives with Different Wall Conditions using Infrared System

Increasing performance parameters of hard disk drive (HDD) such as higher capacity and faster data access speed with decreasing physical size make HDD more susceptible to thermal effects. Contact temperature measurement using thermocouple is not suitable for the rotating platter of HDD. Heat analysis using simulation software requires accurate initial parameter setting such as thermal (initial & boundary) conditions of certain regions. Temperature measurement using infrared (IR) system avoids these limitations;it is non-contact, responsive and does not require initial parameter setting. Thermal pattern distribution can be studied from the thermal images. However, emissivity of the target has to be known and calibration of the system is essential for accurate temperature reading. This paper showed that temperature within the HDD increases with ambient temperature and time, but the thermal distribution pattern in the HDD was not affected by different ambient temperatures. Three wall boundary conditions were conducted to study the thermal distribution pattern in the HDD. A solution was then proposed based on the results obtained from the experiments to improve the heat transfer rate and steady state temperature, and reduce the detrimental effects from high thermal generation in future prototypes. Another important finding was that the averaged temperature of the head cap was generally higher compared to that of the disk, as the spindle motor is the primary heat source within the HDD. Heat source analysis of HDD with IR system allows designers to have better visibility of the temperature generated in different components of the HDD. Proper cooling may enhance disk life as well as ensure the stability and integrity of the system.

Study on divertor heat flux under n=3 and n=4 resonant magnetic perturbations using infrared thermography diagnostic in EAST

Resonant magnetic perturbations(RMPs)with high toroidal mode number n are considered for controlling edge-localized modes(ELMs)and divertor heat flux in future ITER H-mode operations.In this paper,characteristics of divertor heat flux under high-nRMPs(n=3 and 4)in H-mode plasma are investigated using newly upgraded infrared thermography diagnostic in EAST.Additional splitting strike point(SSP)accompanying with ELM suppression is observed under both RMPs with n=3 and n=4,the SSP in heat flux profile agrees qualitatively with the modeled magnetic footprint.Although RMPs suppress ELMs,they increase the stationary heat flux during ELM suppression.The dependence of heat flux on q_(95)during ELM suppression is preliminarily investigated,and further splitting in the original strike point is observed at q 495=during ELM suppression.In terms of ELM pulses,the presence of RMPs shows little influence on transient heat flux distribution.

Laser Heating and Infrared Thermography of Building Materials

In this work, a 532 nm diode CW laser is used to heat samples used as building materials at a 1 meter standoff distance while using an FLIR (Forward-Looking Infrared) thermal camera to monitor and record the heating and then cooling of each sample after lasers are switched off. The data is then analyzed using FLIR proprietary software. Since the absorption spectra of materials are unique, using multiple lasers of different wavelengths to simultaneously shine onto the sample at different locations would give enough thermal data to successfully characterize the samples within a reasonable amount of time. The results are very promising for applications involving non-destructive detection and classification of materials.

Microscale Infrared Observation of Liquid-Vapor Phase Change Process on the Surface of Porous Media for Loop Heat Pipe

Loop Heat Pipe (LHP) performance strongly depends on the performance of a wick that is porous media inserted in an evaporator. In this paper, the visualization results of thermo-fluid behavior on the surface of the wick with microscopic infrared thermography were reported. In this study, 2 different samples that simulated a part of wick in the evaporator were used. The wicks were made by different two materials: polytetrafluoroethylene (PTFE) and stainless steel (SUS). The pore radii of PTFE wick and SUS wick are 1.2 μm and 22.5 μm. The difference of thermo-fluid behavior that was caused by the difference of material was investigated. These two materials include 4 different properties: pore radius, thermal conductivity, permeability and porosity. In order to investigate the effect of the thermal conductivity on wick’s operating mode, the phase diagram on the q-keff plane was made. Based on the temperature line profiles, two operating modes: mode of heat conduction and mode of convection were observed. The effective thermal conductivity of the porous media has strong effect on the operating modes. In addition, the difference of heat leak through the wick that was caused by the difference of the material was discussed.

Thermal-mechanical response of microscale functional film for infrared window

Infrared window in hypersonic missile usually suffers complex aerodynamic force/heat during high-speed flight.A finite element method was adopted to simulate the thermal and stress response of microscale functional film for infrared window under different aerodynamic heats/forces conditions.Temperature and stress distribution were obtained with different heat fluxes.There is almost constant stress distribution along the film thickness except a sudden decrease near the substrate.The maximum stresses are located at the points which are 0.3 mm away from the edges.Different film materials result in different stress values.The temperature and stress in ZrN are larger than those in Y2O3.Besides the numerical simulation,an oxygen propane flame jet impingement test was performed to investigate thermal shock failure of the infrared window.Some place of the window surface has spots damage and some place has line crack damage after thermal shock.

Far Infrared Radiation Property of Rare Earth Mneral Composite Materials

Rare earth mineral composite materials were prepared using rare earths and natural far-infrared mineral materials . The influences of rare earth additive content and heat treatment temperature on the far infrared radiance were studied. The results show that the far infrared radiance of rare earth mineral composite materials is 0.93 when the rare earth additive content is 6% and heat treatment temperature is 750℃.

Tailoring of a robust asymmetric aramid nanofibers/MXene aerogel film for enhanced infrared thermal camouflage and Joule heating performances

The development of infrared(IR)surveillance technology has led to a growing interest in thermal camouflage.However,the trade-off relationship between low IR-emissivity and thermal insulation hinders the advance of thermal camouflage materials.Herein,guided by multi-physics simulation,we show a design of asymmetric aramid nanofibers/MXene(ANF/MXene)aerogel film that realizes high-efficient thermal camouflage applications.The rationale is that the asymmetric structure contains a thermal-insulation three-dimensional(3D)network part to prevent effective heat transfer and a low IR-emissivity(~0.3)dense surface layer to suppress radiative heat emission.It is remarkable that the synergy mechanism in the topology structure contributes to over 40%reduction of target radiation temperature.Impressively,the tailored asymmetric ANF/MXene aerogel film also enables sound mechanical properties such as a Young’s modulus of 44.4 MPa and a tensile strength of 1.3 MPa,superior to most aerogel materials.It also exhibits great Joule heating performances including low driving voltage(4 V),fast thermal response(<10 s),and long-term stability,further enabling its versatile thermal camouflage applications.This work offers an innovative design concept to configure multifunctional structures for next-generation thermal management applications.

Ni Flower/MXene-Melamine Foam Derived 3D Magnetic/Conductive Networks for Ultra-Efficient Microwave Absorption and Infrared Stealth

The development of multifunctional and efficient electromagnetic wave absorbing materials is a challenging research hotspot.Here,the magnetized Ni flower/MXene hybrids are successfully assembled on the surface of melamine foam(MF)through electrostatic self-assembly and dip-coating adsorption process,realizing the integration of microwave absorption,infrared stealth,and flame retardant.Remarkably,the Ni/MXene-MF achieves a minimum reflection loss(RLmin)of−62.7 dB with a corresponding effective absorption bandwidth(EAB)of 6.24 GHz at 2 mm and an EAB of 6.88 GHz at 1.8 mm.Strong electromagnetic wave absorption is attributed to the three-dimensional magnetic/conductive networks,which provided excellent impedance matching,dielectric loss,magnetic loss,interface polarization,and multiple attenuations.In addition,the Ni/MXene-MF endows low density,excellent heat insulation,infrared stealth,and flame-retardant functions.This work provided a new development strategy for the design of multifunctional and efficient electromagnetic wave absorbing materials.

Technological,environmental and biological factors:referent variance values for infrared imaging of the bovine

Background： Despite its variety of potential applications, the wide implementation of infrared technology in cattle production faces technical, environmental and biological challenges similar to other indicators of metabolic state. Nine trials, divided into three classes （technological, environmental and biological factors） were conducted to illustrate the influence of these factors on body surface temperature assessed through infrared imaging. Results： Evaluation of technological factors indicated the following： measurements of body temperatures were strongly repeatable when taken within ]0 s; appropriateness of differing infrared camera technologies was influenced by distance to the target; and results were consistent when analysis of thermographs was compared between judges. Evaluation of environmental factors illustrated that wind and debris caused decreases in body surface temperatures without affecting metabolic rate; additionally, body surface temperature increased due to sunlight but returned to baseline values within minutes of shade exposure. Examination/investigation/exploration of animal factors demonstrated that exercise caused an increase in body surface temperature and metabolic rate. Administration of sedative and anti-sedative caused changes on body surface temperature and metabolic rate, and during late pregnancy a foetal thermal imprint was visible through abdominal infrared imaging. Conclusion： The above factors should be considered in order to standardize operational procedures for taking thermographs, thereby optimizing the use of such technology in cattle operations.

The infrared-induced temperature distributions of solid D_2 ices

A specific-wavelength infrared（IR） light（λ = 3140 nm） was irradiated into a solid D2 ice prepared in a cylinder target cell.The temperature in the solid D2 ice oscillated periodically with a high amplitude when irradiated by the IR light.The temperature oscillation has been well explained based on the two-dimensional heat transfer theory plus the IR-irradiation effect.The transmission optical imaging reveals that such a temperature oscillation is favorable to recrystallize the solid D2 ice from multicrystal to quasi single crystal.This suggests an efficient method to layer the solid hydrogen-isotope ice for the inertial-confinement-fusion（ICF） experiments.

Research on Radiant Carrier of Matching Radiant Type Far Infrared Textiles

This paper deals with the radiation effects of different kinds ofradiant carriers used in making far infrared textile materials.From two radiation experiments,methods of testing radiation ef-fects of carriers have been found,results of the experiments arediscussed.Finally,some conclusions for choosing appropriateradiant carrier are drawn.