Differential pressure difference based altitude control of a stratospheric satellite

An autonomous altitude adjustment system for a stratospheric satellite(StratoSat)platform is proposed.This platform consists of a helium balloon,a ballonet,and a two-way blower.The helium balloon generates lift to balance the platform gravity.The two-way blower inflates and deflates the ballonet to regulate the buoyancy.Altitude adjustment is achieved by tracking the differential pressure difference(DPD),and a threshold switching strategy is used to achieve blower flow control.The vertical acceleration regulation ability is decided not only by the blower flow rate,but also by the designed margin of pressure difference(MPD).Pressure difference is a slow-varying variable compared with altitude,and it is adopted as the control variable.The response speed of the actuator to disturbance can be delayed,and the overshoot caused by the large inertia of the platform is inhibited.This method can maintain a high tracking accuracy and reduce the complexity of model calculation,thus improving the robustness of controller design.

Minor Pressure Differences within the Fontan-Anastomosis in Patients with Total Cavopulmonary Connection by 4D-Flow Magnetic Resonance Imaging

Background: Pressure measurement in total cavopulmonary connection (TCPC) patients is a domain of cardiaccatheterization. 4D velocity encoded cardiovascular magnetic resonance (4D–flow MRI) offers an alternative forassessment of even minor pressure differences. The scope of this study was to measure even minor pressure differencesin the anastomosis of TCPC patients, who are clinically uncompromised. Methods: Twenty-four patients(median 15 years [8;34]) with TCPC were studied prospectively by 4D-flow MRI. Pressure differences betweensuperior vena cava (SVC) and extracardiac conduit (C) to both right pulmonary artery (RPA) and left pulmonaryartery (LPA) were assessed. Small fluid obstructions as vortices within the anastomosis were detected by flowpathlines from 4D-flow MRI. In two patients pressure differences were calculated also by computational flowdynamics (CFD) as a plausibility check for the order of magnitude. Results: Median values of pressure differencesin the anastomosis between SVC and RPA were 0.63 (0.21–2.1) mmHg, between C and RPA 0.67 (0.3–2.2)mmHg, between SVC and LPA 0.8 (0.3–2.4) mmHg and between C and LPA 0.7 (0.2–1.9) mmHg. Patients withpotential flow obstruction (stents, occluder, vortices) had significantly higher gradients at the anastomosis (p <0.05) than patients without potential obstructions, although the absolute values were small. CFD- and measurement-based pressure difference showed good agreement. Conclusion: 4D-flow MRI is able to detect minor pressuredifferences within the Fontan circuit even in patients with apparently satisfactory TCPC. Slightly higherpressure differences are due to the presence of small flow obstruction.

In Tube Condensation:Changing the Pressure Drop into a Temperature Difference for a Wire-on-Tube Heat Exchanger

A theoretical study based on the Penalty factor(PF)method by Cavallini et al.is conducted to show that the pressure drop occurring in a wire-on-tube heat exchanger can be converted into a temperature difference for two types of refrigerants R-134a and R-600a typically used for charging refrigerators and freezers.The following conditions are considered:stratified or stratified-wavyflow condensation occurring inside the smooth tube of a wire-on-tube condenser with diameter 3.25,4.83,and 6.299 mm,condensation temperatures 35℃,45℃,and 54.4℃ and cover refrigerant massflow rate spanning the interval from 1 to 7 kg/hr.The results show that the PF variation is not linear with vapor quality and attains a maximum when the vapor quality is 0.2 and 0.18 for the R-134a and R-600a refrigerants,respectively.The PF increases with the refrigerant massflow rate if the inner diameter and saturation temperature constant,and it decreases on increasing the inner diameter to 6.299 mm for constant refrigerant massflow rate and saturation temperature.The PF for R-600a is higher than that for R-134a due to the lower saturation pressure in thefirst case.Furthermore,a stratifiedflow produces higher PF in comparison to the annularflow due to the effect of the surface tension.

The Impact of Different Mining and Releasing Ratios on the Over-Support Pressure of Header Working Face

Through the theoretical analysis of overburden destabilization mechanism, FLAC 3D simplified plane numerical simulation method and field measurement method, we compared the relationship of overburden support pressure at 35 m of workface recovery, and the peak overburden support pressure decreased from 13.85 Mpa to 11.97 Mpa from 1:1 to 1:3. With the increase of mining ratio, the peak over-supporting pressure decreases: with the increase of top coal recovery thickness, the peak over-supporting pressure and the influence range will be further expanded, and the distance between the peak over-supporting pressure and the coal wall of the working face will be further increased and the high stress zone of the peak area will be expanded simultaneously.

Improved finite difference method for pressure distribution of aerostatic bearing

An improved finite difference method （FDM）is described to solve existing problems such as low efficiency and poor convergence performance in the traditional method adopted to derive the pressure distribution of aerostatic bearings. A detailed theoretical analysis of the pressure distribution of the orifice-compensated aerostatic journal bearing is presented. The nonlinear dimensionless Reynolds equation of the aerostatic journal bearing is solved by the finite difference method. Based on the principle of flow equilibrium, a new iterative algorithm named the variable step size successive approximation method is presented to adjust the pressure at the orifice in the iterative process and enhance the efficiency and convergence performance of the algorithm. A general program is developed to analyze the pressure distribution of the aerostatic journal bearing by Matlab tool. The results show that the improved finite difference method is highly effective, reliable, stable, and convergent. Even when very thin gas film thicknesses （less than 2 Win）are considered, the improved calculation method still yields a result and converges fast.

A fast explicit finite difference method for determination of wellhead injection pressure

A fast explicit finite difference method (FEFDM),derived from the differential equations of one-dimensional steady pipe flow,was presented for calculation of wellhead injection pressure.Recalculation with a traditional numerical method of the same equations corroborates well the reliability and rate of FEFDM.Moreover,a flow rate estimate method was developed for the project whose injection rate has not been clearly determined.A wellhead pressure regime determined by this method was successfully applied to the trial injection operations in Shihezi formation of Shenhua CCS Project,which is a good practice verification of FEFDM.At last,this method was used to evaluate the effect of friction and acceleration terms on the flow equation on the wellhead pressure.The result shows that for deep wellbore,the friction term can be omitted when flow rate is low and in a wide range of velocity the acceleration term can always be deleted.It is also shown that with flow rate increasing,the friction term can no longer be neglected.

Moderators of occupational pressure in female health professionals—Individual differences and coping skills

Individual differences and coping skills have influential impacts on stress process by influencing the eventual outcomes of the stressors, contributing to either wellbeing, or illness and negative experiences. The aim of this paper is to explore the individual differences and coping strategies of a cohort of women with health professionals’ occupational pressure. This is a cross-sectional survey, informed by the transactional model of stress and coping framework, and carried out on women health professionals (n = 203) from the Kuala Lumpur Hospital. Multiple regressions were conducted to examine the potential moderators of stress. Women Health Professionals reported stress with six out of eight organizational sources of pressure, with relationship being a key stressor. Their individual differences (mean + SD) were characterised by low drive (7.6 + 1.9-8.2 + 2.0), low personal influence (10.8 + 2.0 to 11.7 + 2.3), moderate control (13.4 + 3.4 to 16.3 + 2.4), and high impatience behaviour (19.1 + 3.8 to 20.4 + 3.3). With Coping strategy, the Life-work-balance coping is a significant positive predictor for five out of the nine outcomes of occupational pressure [state of mind (p ress management guideline to ameliorate stress amongst those vulnerable workers. Future studies to examine individual differences of these female-dominated professions across health setting are needed to better inform the pressure-at-work issues for the increasing Asian women health professionals.

Effects of temperature and pressure differences on water seepage in breccia

Effects of temperature and pressure differences on water seepage in breccia were investigated by using the physicochemical seepage instrument.The results show that the relationship of flow and pressure differences can be expressed by a linear equation,and the seepage coefficient is linearly correlated with temperature.The relation-ship between seepage flow and temperature could be described with the linear equation.The constant and tempera-ture seepage coefficient showed a linear relation with pressure.Binary quantitative equation for the seepage flow,temperature and pressure was obtained,and explained with experimental data and theoretical analysis.

Exploration on Temporal-spatial Difference of Cultivated Land Pressure and Influence Factor Analysis: A Case Study of Guangxi

Based on related statistical data during 1980-2014,change rule of Guangxi cultivated land pressure level was studied. Taking each municipal administrative division as evaluation unit,temporal-spatial change trend of cultivated land pressure level was explored by establishing pressure index model of cultivated land,and principal component analysis was used to explore the driving force of cultivated land pressure. Results showed that from 1980 to 2014 in Guangxi,cultivated land pressure was at level one in 12 years,level two in 19 years and level three in 4 years; mean of cultivated land pressure in each city during 2005-2014 was taken as average level of cultivated land pressure in the city,in which cultivated land pressure values of Chongzuo City,Baise City,Laibin City,Liuzhou City,Fangchenggang City,Nanning City,Hechi City and Guigang City were all lower than average level in Guangxi at the same period. Driving factors of cultivated land pressure index mainly contained urbanization rate,Engel coefficient of rural households(ECRH),per capita cultivated land area,total population and rural per capita net income(RPFI).

A New Model to Predict Average Pressure Difference of Liquid Droplet and Its Application in Gas Well

The distribution of droplet surface pressure is uneven?under the action of high velocity gas streams in gas wells, and there exists a pressure difference which leads to droplet deformation before and after the droplet. Moreover, it affects the critical liquid carrying rate. The pressure difference prediction model must be determined, because of the existing one lacking theoretical basis. Based on the droplet surface pressure distribution in high velocity gas streams, a new model is established to predict the average differential pressure of droplets. Compared with the new differential pressure prediction results, the existing pressure difference prediction results were overvalued by 46.0%. This article also improves four gas-well critical liquid carrying models using the proposed pressure difference prediction model, and compares with the original one. The result indicates that the critical velocity of the original models is undervalued by 10% or so, due to the overestimate to the pressuredifference. In addition, comparisons of the improved model with original models show that it is necessary to consider the adaptability, because the models have significant differences in results, and different suitability for different well conditions.

Analogy Theory and Application of Pressure Difference of Wind Turbine Blade Profile

This paper aims to design an optimized blade for Horizontal Axis Wind Turbine(HWAT).Since airfoil is a basic component of blade design,an optimized airfoil(referred as SJX)was proposed based on the line theory through the weight analogy to pressure distribution of air flow.Its lift,drag,lift⁃to⁃drag ratio were compared with those NACA2409⁃34,NACA2410,and RK40 airfoils by using Profili software at fixed wind velocity and under different angles of attack.The NACA2409⁃34 airfoil was found to be greatly similar with the SJX airfoil.Based on the Wilson method,blades using SJX and NACA2490⁃34 airfoils were developed and different performance parameters such as velocity distribution,pressure distribution,and power were compared under variable wind velocities and different angles of attack ranging from-4°to 6°at different radius from the center of rotor using computational fluid dynamics(CFD)in ANSYS FLUENT.Results of the study suggested that the performance of the SJX based airfoil and blade was much more optimized.

Simulating Error-Opening of Pressure Relief Valves of a Station on a Continuous Undulating Oil Pipeline with Large Elevation Difference

For oil pipeline in mountain areas,high hydrostatic pressure in the pipeline may cause error-opening of pressure relief valves,and oil is discharged from the pipeline to the pressure relief tanks,bringing spilling-over risk of the pressure relief tanks.Therefore,simulating the error-opening situations of the pressure relief valves and investigating the oil discharge process are necessary for checking the possibility of the spilling-over accident and then proposing measures to improve the pressure relief system.This research focuses on a continuous undulating oil pipeline with large elevation difference and a station along this pipeline,which is named B station in this paper,is studied.By OLGA software,simulation model of the pressure relief system of B station is established,and the accuracy of the model is verified by reconstructing a real accident and making a comparison with the actual accident data.The maximum discharge rate reached 8284 m3/h when the pressure relief valve was opened by mistake in the inlet and outlet of the station.The accumulated filling time of the two pressure relief tanks is 200 s,which is in good agreement with the accident data.On this basis,for error-opening of the pressure relief valves at the inlet and outlet of B station,simulation is performed to investigate variations of the discharge velocity,discharge flow rate,accumulated discharge volume and ventilation volume of the vent valve.The discharge velocity is found to be over the maximum velocity allowed for safety consideration.According to the accumulated discharge volume,it is inferred that spilling over of the pressure relief tanks will be caused once error-opening of the pressure relief valve occurs.Also it is judged that the existing breathing valve can not satisfy the ventilation requirement in case of failure of the pressure relief valves.From these simulation results,it is proposed that increasing the number of vent valves,replacing the manual valves with electrically operated valves,and employing security control interlock protection program are improvement measures to guarantee safe,efficient and reliable operation of the pressure relief system at B station.

Association between Systolic Blood Pressure Difference ≥10 mm Hg and Ankle-Brachial Index

Background: In new outpatients, blood pressure should be measured in both arms. A previous study reported that an inter-arm systolic blood pressure difference (ΔSBP) of ≥10 mm Hg is associated with an increased risk of mortality. Aim: The aim was to identify the associations with absolute values of ΔSBP (|ΔSBP|) ≥10 mm Hg. Subjects and Methods: This study included 2481 patients. Patients with a body mass index ≥25 kg/m2 were defined as obese. The group of A was defined as following: ankle-brachial index (ABI) was <0.9 or ≥1.3. ΔSBP was expressed as right arm BP minus left arm BP. |ΔSBP| ≥10 mm Hg were analyzed using multivariate logistic analysis. Results: |ΔSBP| ≥10 mm Hg was found in 6.0% of patients and |ΔSBP| < 5 mm Hg in 80.4%. In multivariate analysis, the odds ratios (ORs) of the associations with |ΔSBP| ≥10 mm Hg were significantly associated with abnormal ABI and obesity regardless of sex and age. Moreover, the OR of the combined effects of abnormal ABI and obesity was higher than that of abnormal ABI and obesity alone. Conclusion: |ΔSBP| ≥10 mm Hg was associated with abnormal ABI and obesity. In a primary care setting, blood pressure should be actively measured in both arms. This study suggests that the associations with |ΔSBP| ≥10 mm Hg may be a useful part of screening for abnormal ABI.

Viscous warm pressure bulging process of AZ31B magnesium alloy with different ellipticity dies

Based on the bulging principle of different ellipticity dies, the methyl vinyl silicone rubber with excellent thermal stability and heat transfer performance was chosen as the viscous medium. The finite element analysis and experiments of viscous warm pressure bulging （VWPB） of AZ31B magnesium alloy were conducted to analyze the influence of different ellipticity dies on the formability of AZ31B magnesium alloy. At the same time, based on the grid strain rule, the forming limit diagram （FLD） of VWPB of AZ31B magnesium alloy was obtained through measuring the strain of bulging specimens. The results showed that at the temperature range of viscous medium thermal stability, the viscous medium can fit the geometry variation of sheet and generate non-uniform pressure field, and as the die ellipticity increases, the difference value of non-uniform pressure reduces. Meanwhile, according to the FLD, the relationship between part complexity and ultimate deformation was investigated.

Effects of cooling rate on microstructure and mechanical properties of A357 alloy during differential pressure casting process

The microstructure and mechanical properties of A357 alloy under differential pressure casting process with different casting mould materials were studied. The results show that by using SiO2 resin sand the grain size is biggest and the tensile and elongation are the lowest, while the grain size is the smallest and the tensile strength and elongation are the highest when the chill is used, and the grain size, tensile strength and elongation of A357 alloy with SiC resin sand mould are in the middle. Furthermore, the results also demonstrate that for thin wall castings during differential pressure casting processes the grain size, tensile strength and elongation are different at different positions corresponding to the same casting mould material, while at the position of gating the grain size is the smallest and the tensile strength and elongation have the highest values. At the position of edge the grain size, the tensile strength and elongation take the second place. However, in the middle of the thin wall castings the grain size is coarsest and the tensile strength and elongation are the lowest.

An Experimental Study on Atmospheric Pressure Glow Discharge in Different Gases

Usually, the electrical breakdown of dielectric barrier discharge (DBD) at atmo-spheric pressure leads to a filamentary non-homogeneous discharge. However, it is also possible to obtain a diffuse DBD in homogeneous form, called atmospheric pressure glow discharge (APGD). We obtained a uniform APGD in helium and in the mixture of argon with alcohol, and studied the electrical characteristics of helium APGD. It is found that the relationship between discharge current and source frequency is different depending on the difference in gas gap when the applied voltage is kept constant. The discharge current shows an increasing trend with the increased frequency when gas gap is 0.8 cm, but the discharge current tends to decrease with the increased frequency when the gas gap increases. The discharge current always increases with the increased applied voltage when the source frequency is kept constant. We also observed a glow-like discharge in nitrogen at atmospheric pressure.

Laser-Induced Graphite Plasma Kinetic Spectroscopy under Different Ambient Pressures

The laser induced plasma dynamics of graphite material are investigated by optical emission spectroscopy. Abla- tion and excitation of the graphite material is performed by using an 1064nm Nd：YAG laser in different ambient pressures. Characteristics of graphite spectra as line intensity variations and signal-to-noise ratio are presented with a main focus on the influence of the ambient pressure on the interaction of laser-induced graphite plasma with an ambient environment. Atomic emission lines are utilized to investigate the dynamical behavior of plasma, such as the excitation temperature and electron density, to describe emission differences under different ambient conditions. The excitation temperature and plasma electron density are the primary factors which contribute to the differences among the atomic carbon emission at different ambient pressures. Reactions between the plasma species and ambient gas, and the total molecular number are the main factors influencing molecular carbon emis- sion. The influence of laser energy on the plasma interaction with environment is also investigated to demonstrate the dynamical behavior of carbon species so that it can be utilized to optimize plasma fluctuations.

Stability characteristics of ring-stiffened cylindrical shells under different longitudinal and transverse external pressures

Because ring-stiffened cylindrical shell structures have many merits, they are widely used in many areas. However, as the strength of steel increase continuously, ensuring of the structure stability is becoming more and more important. Therefore, it is necessary to carry on a more particular analysis. Based on the understanding and analysis of the characteristics of stability for a ring-stiffened cylindrical shell under uniform external pressure and under external single pressure, the characteristics under different cross uniform external pressures are analyzed, and the regularity of it is also gotten. The curve of stability given various geometrical parameters under different cross uniform external pressures is protracted by the analysis of the theory. The conclusion not only improves the theory structural mechanics, it also was important effects on engineering calculation and design.

Observation Of Reaction On Different Blood Pressure Treated By Needling Neiguan

ＯｂｓｅｒｖａｔｉｏｎＯｆＲｅａｃｔｉｏｎＯｎＤｉｆｆｅｒｅｎｔＢｌｏｏｄＰｒｅｓｓｕｒｅＴｒｅａｔｅｄＢｙＮｅｅｄｌｉｎｇＮｅｉｇｕａｎ￥ＤｕＳｈｉｚｈｏｎｇ（ＨａｎｇｚｈｏｕＦｏｕｒｔｈＨｏｓｐｉｔｏｌＨａｎｇｚｈｏｕ３１０００２）Ｔｈｒｅｅｇｒ...

Clinical Efficacy of Hyperbaric Oxygen Therapy at Different Pressures in the Treatment of Sudden Deafness

Objective:To analyze the efficacy of hyperbaric oxygen at different pressures in the treatment of sudden deafness.Methods:Eighty-two patients with sudden deafness treated in the Affiliated Hospital of Hebei University from September 2019 to September 2021 were selected as the research subjects.The patients were randomly divided into study group 1 and study group 2,and they were treated with hyperbaric oxygen on the basis of routine treatment,in which the pressure used was 1.8 ATA and 2.2 ATA,respectively.Oxygen was delivered via the pressure stabilizing mask for 60 minutes.The patients received two courses of treatment,each lasting 10 days.The changes in hearing(pure tone audiometry)and the clinical efficacy of both the groups were compared before and after treatment.The data obtained were statistically analyzed using SPSS 19.0.Results:The total effective rate of study group 1 was 90.00%,while that of study group 2 was 76.19%.The differences between the two groups were statistically significant(p<0.05).Conclusion:For patients with sudden deafness treated with hyperbaric oxygen,the clinical efficacy of 1.8 ATA is more significant than that of 2.2 ATA.