A kind of Levextrel resin separation process was developed for separation ofindium (III), gallium (III), and zinc (II) from aqueous sulfate solution with Levextrel resincontaining di(2-ethylhexyl) phosphoric acid (CL-...A kind of Levextrel resin separation process was developed for separation ofindium (III), gallium (III), and zinc (II) from aqueous sulfate solution with Levextrel resincontaining di(2-ethylhexyl) phosphoric acid (CL-P 204). The aim of the research is to collectpreliminary results for a pilot-scale production. Properties of adsorbing indium (III), gallium(III), and zinc (II) from sulfate solution with the Levextrel resin were first studied by batchoperation and column operation. The optimum pH, adsorption capacities and concentrations ofstripping agents for indium (III), gallium (III) were tested. The separation order of indium (III),gallium (III), and zinc (II) from sulfate solution with CL-P 204 Levextrel resin was found thatindium (III) could be first separated by adsorbing at the acidity of 1.0 mol/L whereas gallium (III)and zinc (II) could not, and they were adsorbed together by adsorbing at pH =2.8, then separatedfrom each other by stripping with 0.1 and 0.5 mol/L hydrochloric acid, respectively. The recoveriesof three metal ions were all higher than 99 percent. The cyclic properties of this resin are well.展开更多
Four magnetic anion exchange resins （MAERs） were used as adsorbents to purify drinking water. The effect of water quality （pH, temperature, ionic strength, etc.） on the performance of MAER for the removal of disso...Four magnetic anion exchange resins （MAERs） were used as adsorbents to purify drinking water. The effect of water quality （pH, temperature, ionic strength, etc.） on the performance of MAER for the removal of dissolved organic matter （DOM） was also investigated. Among the four studied MAERs, the strong base resin named NDMP- 1 with high water content and enhanced exchange capacity exhibited the highest removal rate of dissolved organic carbon （DOC） （48.9% removal rate） and UV-absorbing substances （82.4% removal rate） with a resin dose of 10 mL/L after 30 rain of contact time. The MAERs could also effectively remove inorganic matter such as sulfate, nitrate and fluoride. Because of the higher specific UV absorbance （SUVA） value, the DOM in the raw water was found to be removed more effectively than that in the clarified water by NDMP resin. The temperature showed a weak influence on the removal of DOC from 6 to 26℃, while a relatively strong one at 36℃. The removal of DOM by NDMP was also affected to some extent by the pH value. Moreover, increasing the sulfate concentration in the raw water could decrease the removal rates of DOC and UV-absorbing substances.展开更多
以2D叠层炭布为增强体,以掺加硅粉、炭粉和碳化硅粉3种无机粉体的糠酮树脂为前驱体,经浸渍、热压固化、炭化裂解和高温热处理过程制备出炭/炭-碳化硅(C/C-SiC)复合材料。采用多功能密度测试仪、扫描电子显微镜(SEM)、X射线衍射仪(XRD)...以2D叠层炭布为增强体,以掺加硅粉、炭粉和碳化硅粉3种无机粉体的糠酮树脂为前驱体,经浸渍、热压固化、炭化裂解和高温热处理过程制备出炭/炭-碳化硅(C/C-SiC)复合材料。采用多功能密度测试仪、扫描电子显微镜(SEM)、X射线衍射仪(XRD)和力学万能试验机,研究了硅粉、炭粉和碳化硅粉的掺加量以及后续化学气相渗透(CVI)处理对C/C-SiC复合材料致密度、微观结构及抗弯强度的影响。结果表明:硅粉、炭粉和碳化硅粉掺加后所形成的碳化硅颗粒对复合材料起到颗粒弥散增强的作用。具体而言,粉体掺加量越多,C/C-SiC复合材料越致密,抗弯强度越大;在三点弯曲载荷作用下,C/C-SiC复合材料呈假塑性断裂模式,并且出现层间开裂现象。对C/C-SiC复合材料进行10 h CVI处理后发现,形成的热解炭可以作为炭纤维与树脂炭基体之间的界面,弥补了树脂炭的微孔,相比于未进行CVI处理的C/C-SiC复合材料,密度最大提高了4.98%,抗弯强度最大提高了38.86%。展开更多
文摘A kind of Levextrel resin separation process was developed for separation ofindium (III), gallium (III), and zinc (II) from aqueous sulfate solution with Levextrel resincontaining di(2-ethylhexyl) phosphoric acid (CL-P 204). The aim of the research is to collectpreliminary results for a pilot-scale production. Properties of adsorbing indium (III), gallium(III), and zinc (II) from sulfate solution with the Levextrel resin were first studied by batchoperation and column operation. The optimum pH, adsorption capacities and concentrations ofstripping agents for indium (III), gallium (III) were tested. The separation order of indium (III),gallium (III), and zinc (II) from sulfate solution with CL-P 204 Levextrel resin was found thatindium (III) could be first separated by adsorbing at the acidity of 1.0 mol/L whereas gallium (III)and zinc (II) could not, and they were adsorbed together by adsorbing at pH =2.8, then separatedfrom each other by stripping with 0.1 and 0.5 mol/L hydrochloric acid, respectively. The recoveriesof three metal ions were all higher than 99 percent. The cyclic properties of this resin are well.
基金supported by the National Natural Science Foundation of China (No.50938004)the National Science Funds for Young Scientists (No.51008152)the Jiangsu Nature Science Fund for Distinguished Scientists, China(No.BK2010006)
文摘Four magnetic anion exchange resins （MAERs） were used as adsorbents to purify drinking water. The effect of water quality （pH, temperature, ionic strength, etc.） on the performance of MAER for the removal of dissolved organic matter （DOM） was also investigated. Among the four studied MAERs, the strong base resin named NDMP- 1 with high water content and enhanced exchange capacity exhibited the highest removal rate of dissolved organic carbon （DOC） （48.9% removal rate） and UV-absorbing substances （82.4% removal rate） with a resin dose of 10 mL/L after 30 rain of contact time. The MAERs could also effectively remove inorganic matter such as sulfate, nitrate and fluoride. Because of the higher specific UV absorbance （SUVA） value, the DOM in the raw water was found to be removed more effectively than that in the clarified water by NDMP resin. The temperature showed a weak influence on the removal of DOC from 6 to 26℃, while a relatively strong one at 36℃. The removal of DOM by NDMP was also affected to some extent by the pH value. Moreover, increasing the sulfate concentration in the raw water could decrease the removal rates of DOC and UV-absorbing substances.
文摘以2D叠层炭布为增强体,以掺加硅粉、炭粉和碳化硅粉3种无机粉体的糠酮树脂为前驱体,经浸渍、热压固化、炭化裂解和高温热处理过程制备出炭/炭-碳化硅(C/C-SiC)复合材料。采用多功能密度测试仪、扫描电子显微镜(SEM)、X射线衍射仪(XRD)和力学万能试验机,研究了硅粉、炭粉和碳化硅粉的掺加量以及后续化学气相渗透(CVI)处理对C/C-SiC复合材料致密度、微观结构及抗弯强度的影响。结果表明:硅粉、炭粉和碳化硅粉掺加后所形成的碳化硅颗粒对复合材料起到颗粒弥散增强的作用。具体而言,粉体掺加量越多,C/C-SiC复合材料越致密,抗弯强度越大;在三点弯曲载荷作用下,C/C-SiC复合材料呈假塑性断裂模式,并且出现层间开裂现象。对C/C-SiC复合材料进行10 h CVI处理后发现,形成的热解炭可以作为炭纤维与树脂炭基体之间的界面,弥补了树脂炭的微孔,相比于未进行CVI处理的C/C-SiC复合材料,密度最大提高了4.98%,抗弯强度最大提高了38.86%。
