Resistive field generation in intense proton beam interaction with solid targets

The Brown-Preston-Singleton(BPS)stopping power model is added to our previously developed hybrid code to model ion beam-plasma interaction.Hybrid simulations show that both resistive field and ion scattering effects are important for proton beam transport in a solid target,in which they compete with each other.When the target is not completely ionized,the self-generated resistive field effect dominates over the ion scattering effect.However,when the target is completely ionized,this situation is reversed.Moreover,it is found that Ohmic heating is important for higher current densities and materials with high resistivity.The energy fraction deposited as Ohmic heating can be as high as 20%-30%.Typical ion divergences with half-angles of about 5°-10°will modify the proton energy deposition substantially and should be taken into account.

Intensity correlation properties of x-ray beams split with Laue diffraction

Beam splitting is one of the main approaches to achieving x-ray ghost imaging, and the intensity correlation between diffraction beam and transmission beam will directly affect the imaging quality. In this paper, we investigate the intensity correlation between the split x-ray beams by Laue diffraction of stress-free crystal. The analysis based on the dynamical theory of x-ray diffraction indicates that the spatial resolution of diffraction image and transmission image are reduced due to the position shift of the exit beam. In the experimental setup, a stress-free crystal with a thickness of hundredmicrometers-level is used for beam splitting. The crystal is in a non-dispersive configuration equipped with a double-crystal monochromator to ensure that the dimension of the diffraction beam and transmission beam are consistent. A correlation coefficient of 0.92 is achieved experimentally and the high signal-to-noise ratio of the x-ray ghost imaging is anticipated.Results of this paper demonstrate that the developed beam splitter of Laue crystal has the potential in the efficient data acquisition of x-ray ghost imaging.

Effects of anode material on the evolution of anode plasma and characteristics of intense electron beam diode

In this paper,three kinds of materials including graphite,titanium(Ti)and molybdenum(Mo)are used as anodes to figure out the influence factors of anode material on the characteristics of the intense electron beam diode.The results show that the characteristics of diode are mainly determined by the cathode plasma motion under a 15 mm diode gap,in which the typical electron beam parameters are 280 kV,3.5 kA.When the diode gap is reduced to 5 mm,the voltage of the electron beam reduces to about 200 kV,and its current increases to more than 8.2 kA.It is calculated that the surface temperatures of Ti and Mo anodes are higher than their melting points.The diode plasma luminescence images show that Ti and Mo anodes produce plasmas soon after the bombardment of electron beams.Ti and Mo lines are respectively found in the plasma composition of Ti and Mo anode diodes.Surface melting traces are also observed on Ti and Mo anodes by comparing the micromorphologies before and after bombardment of the electron beam.These results suggest that the time of anode plasma generation is closely related to the anode material.Compared with graphite,metal Ti and Mo anodes are more likely to produce large amounts of plasma due to their more significant temperature rise effect.According to the moment that anode plasma begins to generate,the average expansion velocities of cathode and anode plasma are estimated by fitting the improved space-charge limited flow model.This reveals that generation and motion of the anode plasma significantly affect the characteristics of intense electron beam diode.

Dynamic energy spectrum and energy deposition in solid target by intense pulsed ion beams

A method for analyzing the dynamic energy spectrum of intense pulsed ion beam(IPIB) was proposed.Its influence on beam energy deposition in metal target was studied with IPIB produced by two types of magnetically insulated diodes(MID).The emission of IPIB was described with space charge limitation model,and the dynamic energy spectrum was further analyzed with time-of-flight method.IPIBs generated by pulsed accelerators of BIPPAB-450(active MID) and TEMP-4M(passive MID) were studied.The dynamic energy spectrum was used to deduce the power density distribution of IPIB in the target with Monte Carlo simulation and infrared imaging diagnostics.The effect on the distribution and evolution of thermal field induced by the characteristics of IPIB dynamic energy spectrum was discussed.

High-energy-density electron beam generation in ultra intense laser-plasma interaction

By using a two-dimensional particle-in-cell simulation,we demonstrate a scheme for highenergy-density electron beam generation by irradiating an ultra intense laser pulse onto an aluminum（Al） target.With the laser having a peak intensity of 4×10^23W cm^-2,a high quality electron beam with a maximum density of 117 nc and a kinetic energy density up to8.79×10^18J m^-3 is generated.The temperature of the electron beam can be 416 Me V,and the beam divergence is only 7.25°.As the laser peak intensity increases（e.g.,1024 W cm^-2）,both the beam energy density（3.56×10^19J m^-3） and the temperature（545 Me V） are increased,and the beam collimation is well controlled.The maximum density of the electron beam can even reach 180 nc.Such beams should have potential applications in the areas of antiparticle generation,laboratory astrophysics,etc.

Effect of longitudinal applied magnetic field on the self-pinched critical current in intense electron beam diode

The effect of applied longitudinal magnetic field on the self-pinched critical current in the intense electron beam diode is discussed. The self-pinched critical current is derived and its validity is tested by numerical simulations. The results shows that an applied longitudinal magnetic field tends to increase the self-pinched critical current. Without the effect of anode plasma, the maximal diode current approximately equals the self-pinched critical current with the longitudinal magnetic field applied; when self-pinched occurs, the diode current approaches the self-pinched critical current.

Space-charge limiting currents for magnetically focused intense relativistic electron beams

The self-consistent differential equations, which describe a laminar-flow equilibrium state in a magnetically focused intense relativistic electron beam propagating inside a conducting waveguide, are presented. The canonical angular momentum, Pe, defined under the conditions at the source, uniquely determines the possible solutions of these equations. By numerically solving these equations, the space-charge limited current and the externally applied magnetic field are obtained in a solid beam and a hollow beam in two cases of Pθ= 0 （magnetically shielded source） and Pθ= const. （immersed source） separately. It is shown that the hollow beam is more beneficial to the propagation of the intense relativistic beam through a drift tube than the solid beam.

Unraveling the efficacy network: A network meta-analysis of adjuvant external beam radiation therapy methods after hepatectomy

BACKGROUND Primary liver cancer is a malignant tumor with a high recurrence rate that significantly affects patient prognosis.Postoperative adjuvant external radiation therapy(RT)has been shown to effectively prevent recurrence after liver cancer resection.However,there are multiple RT techniques available,and the differ-ential effects of these techniques in preventing postoperative liver cancer re-currence require further investigation.AIM To assess the advantages and disadvantages of various adjuvant external RT methods after liver resection based on overall survival(OS)and disease-free survival(DFS)and to determine the optimal strategy.METHODS This study involved network meta-analyses and followed the PRISMA guidelines.The data of qualified studies published before July 10,2023,were collected from PubMed,Embase,the Web of Science,and the Cochrane Library.We included relevant studies on postoperative external beam RT after liver resection that had OS and DFS as the primary endpoints.The magnitudes of the effects were determined using risk ratios with 95%confidential intervals.The results were analyzed using R software and STATA software.RESULTS A total of 12 studies,including 1265 patients with hepatocellular carcinoma(HCC)after liver resection,were included in this study.There was no significant heterogeneity in the direct paired comparisons,and there were no significant differences in the inclusion or exclusion criteria,intervention measures,or outcome indicators,meeting the assumptions of heterogeneity and transitivity.OS analysis revealed that patients who underwent stereotactic body radiotherapy(SBRT)after resection had longer OS than those who underwent intensity modulated radiotherapy(IMRT)or 3-dimensional conformal RT(3D-CRT).DFS analysis revealed that patients who underwent 3D-CRT after resection had the longest DFS.Patients who underwent IMRT after resection had longer OS than those who underwent 3D-CRT and longer DFS than those who underwent SBRT.CONCLUSION HCC patients who undergo liver cancer resection must consider distinct advantages and disadvantages when choosing between SBRT and 3D-CRT.IMRT,a RT technique that is associated with longer OS than 3D-CRT and longer DFS than SBRT,may be a preferred option.

Gaussian wave formalism model for propagation of charged-particle beam through a first-order optical systems

An elliptical Gaussian wave formalism model of a charged-particle beam is proposed by analogy with an elliptical Gaussian light beam. In the paraxial approximation, the charged-particle beam can be described as a whole by a complex radius of curvature in the real space domains. Therefore, the propagation and transform of charged-particle beam passing through a first-order optical system is represented by the ABCD-like law. As an example of the application of this model, the relation between the beam waist and the minimum beam spot at a fixed target is discussed. The result, well matches that from conventional phase space model, and proves that the Gaussian wave formalism model is highly effective and reasonable.

Self-modulation and anomalous collective scattering of laser produced intense ion beam in plasmas

The collective interaction between intense ion beams and plasmas is studied by simulations and experiments,where an intense proton beam produced by a short pulse laser is injected into a pre-ionized gas.It is found that,depending on its current density,collective effects can significantly alter the propagated ion beam and the stopping power.The quantitative agreement that is found between theories and experiments constitutes the first validation of the collective interaction theory.The effects in the interaction between intense ion beams and background gas plasmas are of importance for the design of laser fusion reactors as well as for beam physics.

Hydrodynamic Effects on Surface Morphology Evolution of Titanium Alloy under Intense Pulsed Ion Beam Irradiation

The hydrodynamic effects of molten surface of titanium alloy on the morphology evolution by intense pulsed ion beam （IPIB） irradiation are studied. It is experimentally revealed that under irradiation of IPIB pulses, the surface morphology of titanium alloy in a spatial scale of μm exhibits an obvious smoothening trend. The mechanism of this phenomenon is explained by the mass transfer caused by the surface tension of molten metal. Hydrodynamic simulation with a combination of the finite element method and the level set method reveals that the change in curvature on the molten surface leads to uneven distribution of surface tension. Mass transfer is caused by the relief of surface tension, and meanwhile a flattening trend in the surface morphology evolution is achieved.

Simulation of high-intense beam transport in electrostatic accelerating column

An electrostatic accelerating column was designed and fabricated by Lanzhou University for an intense DT/D-D neutron generator. In order to achieve a neutron yield of 5.0 × 10^(12)n/s, a deuteron beam of 30 mA,accelerated to 400 kV, and transported in the electrostatic accelerating column smoothly are required. One particle-in-cell code BEAMPATH was used to simulate the beam transport, and the IONB 1.0 code was used to simulate the intense beam envelopes. Emittance growths due to space charge effect and spherical aberration were analyzed. The simulation results show that the accelerating column can transport deuteron beam of 30 mA smoothly and the requirement for the neutron generator is satisfied.

Production of intense highly charged ion beams by IMP 14.5 GHz electron cyclotron resonance ion source

A new 14.5 GHz Electron Cyclotron Resonance (ECR) ion source has been constructed over the last two years. The source was designed and tested by making use of the latest results from ECR ion source development, such as high mirror magnetic field, large plasma volume, and biased probe. 140uA of O^7+, 185uA of Ar^11+ and 50uA of Xe^26+ could be produced with a RF power of 800 W. The intense beams of highly charged metallic ions are produced by means of the method of a metal evaporation oven and volatile compound through axial access. The test results are 130uA of Ca^11+, 70uA of Ca^12+ and 65uA of Fe^lo+. The ion source has been put into operation for the cyclotron at the institute of Modern Physics (IMP).

Calculation of Beam Intensity Distribution for the Neutral Beam Injection in EAST

Theoretical beam intensity distribution is derived for the neutral-beam-injection ion source with a multi-slot extraction in EAST. The beam intensity profile, both along and perpendicular to the injecting direction and the beam power deposition to the inner elements in the neutral beam injector （NBI） are evaluated. The results indicate that the transverse beam intensity is much higher than the longitudinal one. This study could provide information for the design of vacuum system, structure of inner elements and cooling system of the neutral beam injector in EAST.

Intensity distribution properties of Gaussian vortex beam propagation in atmospheric turbulence

By using wave optics numerical simulation, the intensity-hole effect, beam spreading and wandering properties of Gaussian vortex beam propagation in atmospheric turbulence are investigated quantitatively. It is found that an intensity hole in the center of the beam pattern appears gradually as a Gaussian vortex beam propagates. The size of the intensity hole increases with the increase of the topological charge of the vortex phase. However, the intensity hole could to some extent be filled with optical energy by atmospheric turbulence, especially in strong turbulence. The radius of the intensity hole first decreases and then increases with the growth of turbulence strength. The effective radius of vortex beam with larger topological charge is greater than with a smaller topological charge. But the topological charge has no evident influence on beam wandering.

Consistency of the directionality of partially coherent beams in turbulence expressed in terms of the angular spread and the far-field average intensity

Under the quadratic approximation of the Rytov＇s phase structure function, this paper derives the general closed-form expressions for the mean-squared width and the angular spread of partially coherent beams in turbulence. It finds that under a certain condition different types of partially coherent beams may have the same directionality as a fully coherent Gaussian beam in free space and also in atmospheric turbulence if the angular spread is chosen as the characteristic parameter of beam directionality. On the other hand, it shows that generally, the directionality of partially coherent beams expressed in terms of the angular spread is not consistent with that in terms of the normalized far-field average intensity distribution in free space, but the consistency can be achieved due to turbulence.

Long-and short-term average intensity for multi-Gaussian beam with a common axis in turbulence

With the help of the extended Huygens-Fresnel principle and the short-term mutual coherence function, the analytical formula of short-term average intensity for multi-Gaussian beam （MGB） in the turbulent a^mosphere has been derived. The intensity in the absence of turbulence and the long-term average intensity in turbulence can both also be expressed in this formula. As special cases, comparisons among short-term average intensity, long-term average intensity, and the intensity in the absence of turbulence for flat topped beam and annular beam are carried out. The effects of the order of MGB, propagation distance and aperture radius on beam spreading are analysed and discussed in detail.

Influence of high-intensity pulsed ion beams irradiation on oxidation behavior of 316L stainless steel at 700℃

316L stainless steel samples, as a widespread used material, were irradiated with HIPIB at the beam parameters of ion energy 300 keV, current density 100, 200 and 300 A/cm2, shot number 10 and pulse duration 75 ns. The surface morphology and the phase structure in the near surface region of original and treated samples were analyzed with scanning electron microscopy (SEM) and X-ray diffractometry (XRD). It is shown that the HIPIB irradiation can smooth the surface of the samples, and the preferred orientation is present in the surface layer of irradiated coupons. The influence of HIPIB irradiation on the oxidation behavior of 316L stainless steel at 700℃for up to 100 h was investigated. Electron probe microanalysis (EPMA) was used to study the distribution of elements in the oxidation products. It is found that the oxidation behavior of the irradiated coupons depends greatly on the ion current density of HIPIB. HIPIB irradiation with ion current density of 100 A/cm2 slightly reduces the oxidation rate with respect to the unirradiated coupon. The improvement of the oxidation resistance can be attributed to more oxide of Cr that forms on the surface of the irradiated coupons. In contrast, HIPIB irradiation with ion current density of 200 or 300 A/cm2 is proved to be detrimental, causing a higher oxidation rate.

Numerical study on the thermo-stress of ZrO_2 thermal barrier coatings by high-intensity pulsed ion beam irradiation

This paper studies numerically the thermo-mechanical effects of ZrO2 thermal barrier coatings （TBCs） irradiated by a high-intensity pulsed ion beam in consideration of the surface structure. Taking the deposited energy of ion beams in TBCs as the source term in the thermal conduction equation, the distribution of temperature in TBCs was simulated. Then, based on the distribution, the evolution of thermal stress was calculated by the finite element method. The results show that tensile radial stress formed at the valley of TBC surfaces after irradiation by HIPIB. Therefore, if cracks happen, they must be at valleys instead of peaks. As for the stress waves, no matter whether through peak or valley position, tensile and compressive stresses are present alternately inside TBCs along the depth direction, and the strength of stress decreases with time.

The Effect of Intensity Pulsed Ion Beam Irradiation on Wear Resistance of High-speed Steel

The structural and phase transformations occurring in the near-surface layers of pre-quenched W6Mo5Cr4V2 high-speed steel (HSS) subjected to intensity pulsed ion beam (IPIB) melting have been investigated. The effect of IPIB irradiation on wear resistance of the HSS has also been studied. The IPIB consists mainly of Cn+(30%)^0 H+(70%), with a high beam current density of 80A/cm2, acceleration voltage of 250kV, pulse duration of 70 ns. Samples were bombarded with 1, 3, 5 pulses respectively. It has been revealed that after IPIB irradiation the initial martensite in the near-surface layer of HSS changed into austenite and produced residual stresses by using electron microscopy and X-ray diffraction. Redistribution and interlace of dislocations in the irradiated samples were generated under the impact of shock wave. With increasing pulse times gradual liquid-phase dissolution of M6C carbide particles occurs in the near-surface layer and produces nanocrystalline MC. This process results in the decrease of martensite crystal (a-phase) and increase of austenite (y-phase) content and the dispersed carbide. Wear resistance of the HSS is improved by a factor of 2, which is explained by the formation of metastable phases such nanocrystal and residual stresses and the redistribution and interlace of dislocations.