A new strategy for ionospheric remote sensing using the 130.4/135.6 nm airglow intensity ratios

We demonstrate here that global-scale determination of a key ionospheric parameter,the peak height of the F_(2)region(h_(m)F_(2)),can be obtained by making a simple ratio measurement of the atomic oxygen 130.4 and 135.6 nm emissions in the far-ultraviolet nightglow with a nadir-viewing system such as a pair of photometers suitable for flight on a CubeSat.We further demonstrate that measurements from an altitude that is within the typical range of nighttime h_(m)F_(2)250−450 km can provide the ratios that are needed for retrieval of the h_(m)F_(2).Our study is conducted mostly through numerical simulations by using radiative transfer models of the two emissions coupled with empirical models of the atmosphere and ionosphere.Modeling results show that the relationship between the h_(m)F_(2)and the intensity ratio is sensitive to the altitude from which the emissions are observed,primarily because of the distinctly different degrees of resonant scattering of the two emissions in the atmosphere.A roughly quadratic relationship can be established for observations from an orbit of~400 km,which enables h_(m)F_(2)retrieval.Parametric analysis indicates that the relationship can be affected by the ambient atmospheric conditions through resonant scattering and O2 absorption.For typical nighttime conditions with h_(m)F_(2)250−450 km,retrieval of the h_(m)F_(2)from synthetic observations shows that the typical errors are only a few kilometers(up to~20 km),depending on the accuracy of the ambient conditions predicted by the empirical models.Our findings pave the way for use of the 130.4/135.6 nm intensity ratios for global-scale monitoring of the nighttime ionosphere at mid to low latitudes.

MULTI-PEAK MATCH INTENSITY RATIO METHOD OF QUANTI-TATIVE X-RAY DIFFRACTION PHASE ANALYSIS

A new method for quantitative phase analysis is proposed by using X-ray diffraction multi-peak match intensity ratio. This method can obtain the multi-peak match intensity ratio among each phase in the mixture sample by using all diffraction peak data in the mixture sample X-ray diffraction spectrum and combining the relative intensity distribution data of each phase standard peak in JCPDS card to carry on the least square method regression analysis. It is benefit to improve the precision of quantitative phase analysis that the given single line ratio which is usually adopted is taken the place of the multi-peak match intensity ratio and is used in X-ray diffraction quantitative phase analysis of the mixture sample. By analyzing four-group mixture sample, adopting multi-peak match intensity ratio and X-ray diffraction quantitative phase analysis principle of combining the adiabatic and matrix flushing method, it is tested that the experimental results are identical with theory.

Improvement in classification accuracy of stainless steel alloys by laser-induced breakdown spectroscopy based on elemental intensity ratio analysis

Laser-induced breakdown spectroscopy(LIBS) is a useful technique for accurate sorting of metal scrap by chemical composition analysis.In this work,a method for intensity-ratiobased LIBS classification of stainless steel applicable to highly fluctuating LIBS signal conditions is proposed.The spectral line pairs for intensity ratio calculation are selected according to elemental concentration and upper levels of emission lines.It is demonstrated that the classification accuracy can be significantly improved from that of full-spectra principal component analysis or intensity-based analysis.The proposed method is considered to be suited to an industrial scrap sorting system that requires minimal maintenance and low system price.

The intensity ratio I (557.7 nm)/I (427.8 nm) at Zhongshan Station in Antarctica

Auroral intensity ratios at Zhongshan Station in Antarctica on 8 April 1999 are studied, along with variations in pene- trated electron energy. Ratios of/（557.7 nm）/I （427.8 nm） during the quiet period were from 5 to 22, and I （630.0 nm） / I （427.8 rim） ranged from 1 to 2.76. These variations were not caused by changes of atomic oxygen concentration, but rather by penetrated electron energy variability, or other mechanisms. Ratios decreased sharply during the auroral substorm, ranging from 1.66--6.5 and 0.071-1, respectively, mainly because of the increase in penetrated electron energy. At the onset of the substorm, the ratios reached their minima. This means that penetrated electron energy was maximized. When the substorm weakened, the penetrated electron energy returned to the pre-substorm level.

〔C II〕Continuum Intensity Ratio in the Far-Infrared Toward the Central Kiloparsec of the Nearby Spiral Galaxy M31

We observed the nearby galaxy M31 in the 〔C II〕158 μm emission line. An extended component was detected over the central 1 5 kpc region with a line-to-continuum ratio of 〔C II〕/〔40-120μm〕6×10 -3 . This ratio is 3 times larger than that of the Galactic counterpart and is comparable to that in the general Galactic Plane. We expect that the difference between the two central regions are due to different gas densities; the self-shielding of CO molecules decreases the C + abundance at the higher density in the Galactic case.

Green and red up-conversion emissions and thermometric application of Er^(3+) -doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663 nm of wavelength, corresponding respectively to the ^2H11/2 → ^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 → ^4I15/2 transitions of Er^3＋ ions, have been observed for the Er^3＋-doped silicate glass excited by a 978 nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296-673 K, which shows that Er^3＋-doped silicate glass can be used as a sensor in high-temperature measurement.

Robust and high-sensitivity thermal probing at the nanoscale based on resonance Raman ratio (R3)

Raman spectroscopy-based temperature sensing usually tracks the change of Raman wavenumber,linewidth and intensity,and has found very broad applications in characterizing the energy and charge transport in nanomaterials over the last decade.The temperature coefficients of these Raman properties are highly material-dependent,and are subjected to local optical scattering influence.As a result,Raman-based temperature sensing usually suffers quite large uncertainties and has low sensitivity.Here,a novel method based on dual resonance Raman phenomenon is developed to precisely measure the absolute temperature rise of nanomaterial(nm WS_(2) film in this work)from 170 to 470 K.A 532 nm laser(2.33 eV photon energy)is used to conduct the Raman experiment.Its photon energy is very close to the excitonic transition energy of WS_(2) at temperatures close to room temperature.A parameter,termed resonance Raman ratio(R3)Ω=I_(A1g)/IE_(2g) is introduced to combine the temperature effects on resonance Raman scattering for the A_(1g) and E_(2g) modes.Ω has a change of more than two orders of magnitude from 177 to 477 K,and such change is independent of film thickness and local optical scattering.It is shown that when Ω is varied by 1%,the temperature probing sensitivity is 0.42 K and 1.16 K at low and high temperatures,respectively.Based on Ω,the in-plane thermal conductivity(k)of a∼25 nm-thick suspended WS_(2) film is measured using our energy transport state-resolved Raman(ET-Raman).k is found decreasing from 50.0 to 20.0 Wm^(−1) K^(−1) when temperature increases from 170 to 470 K.This agrees with previous experimental and theoretical results and the measurement data using our FET-Raman.The R3 technique provides a very robust and high-sensitivity method for temperature probing of nanomaterials and will have broad applications in nanoscale thermal transport characterization,non-destructive evaluation,and manufacturing monitoring.

Rare Earth Doped Optical Fibers for Temperature Sensing Utilizing Ratio-Based Technology

A new and practical fluorescence temperature detecting system based on fluorescence intensity ratio was proposed . The background theory of fluorescence intensity-ratio method was presented simply. And the characters of rare earth doped samples were detailed. The erbium-doped fiber was chosen as the sensing element. The energy levels of 2H11/2 and 4S3/2 are responsible for the emission of radiation at approximately 530 and 555 nm. The erbium-doped (960 ppm) fiber of length 20 cm and core diameter 3.2μm was used as the sensing part. A silica photodiode transfers the fluorescence signal to electric signal, then the ratio of the average of the two different signals was calculated by the computer and the temperature was obtained. The ratio R of the intensity resulting from the transition between the two levels varies proportionly with temperature interval from 293 K to 373 K. The sensitivity of the sensor is approximately 0.05 K-1.

Resolution of Two Unequally Bright Points of Apodized Optical Systems with Asymmetric Circular Antenna Arrays

Sparrow criterion of resolution is used for assessment of the resolution of two object points of apodized optical systems under incoherent illumination of light. Semicircular arrays of circular aperture with discrete asymmetric apodization have suppressed side-lobes and a narrower central peak in the image plane termed as PSF good side on alternatively the right and left of the strong spectral point facilitates to detect the presence of weak spectral point in the vicinity of bright spectral point. The results of investigations on optimum discrete pupil function with semicircular arrays on the intensity distributions in the composite image of two object points with widely varying in their intensities under various degree of coherence of illumination have been studied. Sparrow resolution limits and the dip in central intensity as function of degree of coherence of the illumination (γ), intensity ratio (α), degree of asymmetric apodization (b) and number of discrete elements in semicircular array (n). The efficiency of aperture functions is discussed in terms of these parameters. Pupil function capabilities in redistribution of energy in composite image of two object points in close vicinity have been verified for different considerations. Current study has found an improvement in two-point resolution characteristics compared to their unapodized counter part. Fourier analytical properties of an optical system are presented for evaluation of this practical problem.

Geochemical signatures of potassium metasomatism in anthracite from the Himalayan fold‑thrust belts of Sikkim,India

The present study focuses on the inorganic geochemical features of the bituminous coal samples from the Raniganj and the Jharia Basins,as well as the anthracite samples from the Himalayan fold-thrust belts of Sikkim,India.The SiO_(2)content(48.05 wt%to 65.09 wt%and 35.92 wt%to 50.11 wt%in the bituminous and anthracite samples,respectively)and the ratio of Al_(2)O_(3)/TiO_(2)(6.97 to 17.03 in the bituminous coal samples and 10.34 to 20.07 in the anthracite samples)reveal the intermediate igneous source rock composition of the minerals.The ratio of the K_(2)O/Al_(2)O_(3)in the ash yield of the bituminous coal samples(0.03 to 0.09)may suggest the presence of kaolinite mixed with montmorillonite,while its range in the ash yield of the anthracite samples(0.16 to 0.27)may imply the presence of illite mixed with kaolinite.The chemical index of alteration values may suggest the moderate to strong chemical weathering of the source rock under sub-humid to humid climatic conditions.The plot of the bituminous coal samples in the A–CN–K diagram depicts the traditional weathering trend of parent rocks,but the anthracite samples plot near the illite feld and are a bit ofset from the weathering trend.This may imply the plausible infuences of the potassium-metasomatism at post coalifcation stages,which is further supported by high K_(2)O/Na_(2)O ratio(29.88–80.13).The Fourier transform infrared spectra further reveal the hydroxyl stretching intensity of illite in the anthracite samples substantiating the efect of the epigenetic potassium-metasomatism.The decrease in total kaolinite intensity/compound intensity of quartz and feldspar may provide additional evidence towards this epigenetic event.

Calculation of the Effect of Opacity on the Solar Spectral Lines of CIV

In this paper, using the intensity ratio between two spectral lines arising from the common lower level, we determine the optical depth of the solar atmosphere of CIV emission lines. The optical depth at the line center of the （1/2-3/2） component is calculated to be 0.05 at the center of the solar disc. By introducing a measured abundance of carbon and the results of ionization balance calculations, we estimate the line-of-sight physical thickness of the regions emitting CIV lines as Heff = 27 km, and we estimate the population density of the lower level to be 1.8 × 106 cm-3 .

Chemical Effect Analyses of 3d Elements by Study of X-Ray Fluorescence Spectra

Spectra of KX-rays emitted from pure 3 dtransition metals and their oxide and sulfate compounds were measured using a single crystal wavelength dispersive X-ray spectroscopy(WDXRF).The measurements were performed using a ZSX-100 esequential spectrometer equipped with an RhX-ray tube operated.An accurate analytical representation of each line was obtained by a fit to a Lorentz function.The spectra were analyzed in order to examine the KX-ray peak parameters such as asymmetry index,peak energy and relative intensity ratios.The energy shifts and relative intensities weredetermined tobetter understand the chemical effect.

Kr L X-ray and Au M X-ray emission for 1.5 MeV–3.9 MeV Kr^(13+) ions impacting on an Au target

Kr L X-ray and Au M X-ray emission for Kr13＋ ions with energies of 1.5 MeV and 3.9 MeV impacting on an Au target are investigated at heavy ion research facility in Lanzhou （HIRFL）. The L-shell X-ray yield per ion of Kr is measured as a function of incident energy. In addition, Kr L X-ray production cross section is extracted from the yield and compared with the result obtained from the classical binary-encounter approximation （BEA） model. Furthermore, the intensity ratio of the Au M/33 to Ma1 X-ray is investigated as a function of incident energy.

Interaction among fractures and stress field computation of fracture systems

The interaction problem among fractures under the action of compressional stress is studied in this paper by using the finite element method and boundary element method respectively.The mechanical criteria which differentiate between the independent fractures and fracture systems and their computation methods are presented in this paper.The proportional conditions between length and spacing of fractures that exist interaction for several kinds of fracture groups of different geometric arrangement are given.The effect of interaction among fractures on the displacement field,stress field and strain energy distribution are computed.The relations between the fracture system of conjugate array and conjugate earthquakes are also discussed in this paper.

A novel Tb^(3+) and Eu^(3+) co-doped dual-emitting phosphate K_(3)SrBi(P_(2)O_(7))_(2) phosphor for application in FIR thermometers

Rare earth co-doped phosphor for fluorescence intensity ratio(FIR) thermometer has gained increasing attention in recent years. Herein, the novel Tb^(3+)and Eu^(3+)co-doped K_(3)SrBi(P_(2)O_(7))_(2)(KSBP) phosphate phosphors were reported. The crystal structure of the title phosphor was determined using Rietveld refinement and proved to have a three-dimensional structure. The time-resolved spectroscopy reveals that there is almost no energy transfer between Tb^(3+)and Eu^(3+). More importantly, Tb^(3+)and Eu^(3+)emissions show different thermal quenching behaviors, which claims the potential of this material for application in optical thermometer. The FIR of the typical KSBP:0.02Tb^(3+),0.04Eu^(3+)sample demonstrates a polynomial relationship as a function of temperature and the absolute and relative sensitivity are0.025 K^(-1) and 0.59%/K, respectively. In general, our study reports a novel and potential KSBP:Tb^(3+),Eu^(3+)phosphate phosphor that is promising for use in high-sensitive FIR thermometers.

Effect of radiative loss mechanisms on FIR thermometric parameters of Nd^(3+)-doped lithium tellurite glasses

Nd^(3+)-doped tellurite glasses are promising materials for thermometers based on the fluorescence intensity ratio(FIR)technique.Nevertheless,at high Nd^(3+)concentrations,energy transfer(ET)processes such as optical reabsorption and cross-relaxation can affect the Nd^(3+)emission,which has been little explored in the literature.Therefore,the present work investigated the use of Nd^(3+)-doped tellurite glass(samples doped with Nd^(3+)at 0.2 mol%,0.5 mol%,2.0 mol%,and 4.0 mol%)in fluorescence thermometers,in the temperature range from 299 to 371 K.The results indicate a strong dependence of the FIR parameters on the Nd^(3+)concentration,due to changes in the emission band profiles caused by optical reabsorption of the Nd^(3+)emissions and cross-relaxation processes.A decrease of the relative sensitivity of the ratio^(4)F_(5/2)→^(4)I_(9/2)/^(4)F_(3/2)→^(4)I_(9/2)is observed for samples doped with higher amounts of Nd^(3+).The maximum relative sensitivity at 299 K is 3.00%/K,which is the highest value among the reported Nd^(3+)ions.

A ratiometric optical thermometer with dual-color emission based on Eu^(2+)-doped CsCu_(2)I_(3) microcrystals

With the increasing demand for non-co ntact fluorescence intensity ratio-based optical thermometry,novel phosphor materials with high-efficiency,dual-emitting centers,and differentiable temperature sensitivity are highly desired,In this wo rk,rare earth Eu^(2+) ions were incorporated Wnto CsCu_(2)I_(3) microcrystals by solidstate reaction,Under a single UV excitation,the as-synthesized samples exhibit two emissions:452 nm blue emission from the 5d→4f transition of Eu^(2+)and 582 nm yellow emission from self-trapped exciton e mission of CsCu_(2)I_(3).The photoluminescence quantum yield reaches to 50%,The dual-band emission of Eu^(2+)-doped CsCu_(2)I_(3) shows different temperature responses in the range of 260-360 K.Based on fluorescence intensity ratio technology,the maximum absolute sensitivity and re Iative sensitivity are 0.091 K^(-1)(at 360 K) and 2.60%/K(at 260 K),respectively.These results suggest that Eu^(2+)-doped GsCu_(2)I_(3) could be a good candidate for highly sensitive optical thermometer.

An abnormal fluorescence intensity ratio between two green emissions of Er^(3+) caused by heating effect of 980 nm excitation

An abnormal fluorescence intensity ratio （FIR） between two green emissions of Er3＋, at room temperature, which is larger than a normal value, emerged in many reported articles. However, up to now detailed work has seldom been done to clarify this abnormal phenomenon. In this paper, green upconversion luminescence of the β-NaLuF4：20%yb3＋,2%Er3＋ powder sample was investigated under 980 um excitation at different circumstances, different pump power densities and different temperatures as well as different air pressures. The corresponding local temperature calculated using FIR technique increased gradually with the enhancement of the pump power density. It was demonstrated that high pump power density of 980 nm laser led to the increase of local temperature of the luminescent material, which further gave the abnormal FIR.

Correlation between magnetic resonance T2 image signal intensity ratio and cell apoptosis in a rabbit spinal cord cervical myelopathy model

Background Cervical spondylotic myelopathy （CSM） is a common cause of disability in elderly patients.Previous studies have shown that spinal cord cell apoptosis due to spinal cord compression plays an important role in the pathology of myelopathy.Although changes in magnetic resonance imaging （MRI） T2 signal intensity ratio （SIR） are considered to be an indicator of CSM,little information is published supporting the correlation between changes in MRI signal and pathological changes.This study aims to testify the correlation between MRI T2 SIR changes and cell apoptosis using a CSM animal model.Methods Forty-eight rabbits were randomly assigned to four groups：one control group and three experimental chronic compression groups,with each group containing 12 animals.Chronic compression of the cervical spinal cord was implemented in the experimental groups by implanting a screw in the C3 vertebra.The control group underwent sham surgery.Experimental groups were observed for 3,6,or 9 months after surgery.MRI T2-weighted SIR Tarlov motor scores and cortical somatosensory-evoked potentials （CSEPs） were periodically monitored.At each time point,rabbits from one group were sacrificed to determine the level of apoptosis by histology （n=6） and Western blotting （n=6）.Results Tarlov motor scores in the compression groups were lower at all time points than the control group scores,with the lowest score at 9 months （P ＜0.001）.Electrophysiological testing showed a significantly prolonged latency in CSEP in the compression groups compared with the control group.All rabbits in the compression groups showed higher MRI T2 SIR in the injury epicenter compared with controls,and higher SIR was also found at 9 months compared with 3 or 6 months.Histological analysis showed significant apoptosis in the spinal cord tissue in the compression groups,but not in the control group.There were significant differences in apoptosis degree over time （P ＜0.001）,with the 9-month group displaying the most severe spinal cord apoptosis.Spearman＇s rank correlation test showed that there was close relation between MRI SIR and degree of caspase-3 expression in Western blotting （r=0.824.P ＜0.001）.Conclusions Clear apoptosis of spinal cord tissue was observed during chronic focal spinal compression.Changes in MRI T2 SIR mav be related to the severity of the apoptosis in cervical spinal cord.

Multi-site occupancies and dependent photoluminescence of Ca_(9)Mg_(1.5)(PO_(4))_(7):Eu^(2+) phosphors:A bifunctional platform for optical thermometer and plant growth lighting

Herein,we demonstrate an optical thermometer based on single Eu^(2+)doped Ca_(9)Mg_(1.5)(PO_4)_7 phosphors,which were prepared by traditional solid-state reaction technique under a reduction atmosphere.Considerations on the bond length obtained by the crystal structure refinement and the dependent photoluminescence performances allow to assign the two distinct emission bands to Eu^(2+)ions occupied Cal-Ca3 and Mg2 sites.Moreover,the blue and red emitting bands perfectly match with the photosynthetic action spectrum,which can enhance the indoor plant photosynthesis.The optimal doping content of Eu^(2+)ions in this Ca_(9)Mg_(1.5)(PO_(4))_(7)system is 3 mol%.The corresponding concentration quenching effect is verified as dipole-dipole interaction with the critical distance of 3.315 nm.Furthermore,by exploiting the fluorescence intensity technique,the optical thermal resistance properties of Ca_(9)Mg_(1.5)(PO_4)_7:Eu^(2+)are identified based on the temperature dependent emission spectra in a range of 303-523 K.In detail,the maximum absolute and relative sensitivity S_(a)and S_(r)of Ca_9Mg_(1.5)(PO_(4))_(7):Eu^(2+)thermometer are as high as 0.637%/K and 0.3155 K^(-1),respectively.Consequently,the Eu^(2+)doped Ca_(9)Mg_(1.5)(PO_(4))_(7)phosphors establish a bifunctional platfo rm for both optical the rmometer and plant growth lighting via multi-site occupancies.