Nonlinear time-reversal interferometry with arbitrary quadratic collective-spin interaction

Atomic nonlinear interferometry has wide applications in quantum metrology and quantum information science.Here we propose a nonlinear time-reversal interferometry scheme with high robustness and metrological gain based on the spin squeezing generated by arbitrary quadratic collective-spin interaction,which could be described by the Lipkin–Meshkov–Glick(LMG)model.We optimize the squeezing process,encoding process,and anti-squeezing process,finding that the two particular cases of the LMG model,one-axis twisting and two-axis twisting outperform in robustness and precision,respectively.Moreover,we propose a Floquet driving method to realize equivalent time reverse in the atomic system,which leads to high performance in precision,robustness,and operability.Our study sets a benchmark for achieving high precision and high robustness in atomic nonlinear interferometry.

Study on the application of optical interferometry in the measurement of the coating thickness of color-coated plates

The principle and application of optical interferometry to measure the coating thickness of color-coated plates were introduced in this paper.Additionally,several factors affecting the test results,including coating refractive index,wavelength range,and film thickness range setting,were analyzed.Among these,the refractive index of the color coating,which cannot be measured directly,was identified as the key factor.A solution to this problem was proposed.Finally,the optical interference method and the current detection methods,including the micrometer method and the magnetic eddy current method,were analyzed and compared.The results show that optical interferometry has better repeatability and reproducibility than the current methods and show no significant difference from the current methods through statistical tests.Therefore,the method can be applied to the detection of the coating thickness of color-coated plates.

Achieving 1.2 fm/Hz^(1/2)Displacement Sensitivity with Laser Interferometry in Two-Dimensional Nanomechanical Resonators:Pathways towards Quantum-Noise-Limited Measurement at Room Temperature

Laser interferometry is an important technique for ultrasensitive detection of motion and displacement.We push the limit of laser interferometry through noise optimization and device engineering.The contribution of noises other than shot noise is reduced from 92.6%to 62.4%,demonstrating the possibility towards shotnoise-limited measurement.Using noise thermometry,we quantify the laser heating effect and determine the range of laser power values for room-temperature measurements.With detailed analysis and optimization of signal transduction,we achieve 1.2 fm/Hz^(1/2)displacement measurement sensitivity at room temperature in twodimensional(2D)Ca Nb_(2)O_(6)nanomechanical resonators,the best value reported to date among all resonators based on 2D materials.Our work demonstrates a possible pathway towards quantum-noise-limited measurement at room temperature.

Wide-spectrum optical synthetic aperture imaging via spatial intensity interferometry

High resolution imaging is achieved using increasingly larger apertures and successively shorter wavelengths.Optical aperture synthesis is an important high-resolution imaging technology used in astronomy.Conventional long baseline amplitude interferometry is susceptible to uncontrollable phase fluctuations,and the technical difficulty increases rapidly as the wavelength decreases.The intensity interferometry inspired by HBT experiment is essentially insensitive to phase fluctuations,but suffers from a narrow spectral bandwidth which results in a lack of effective photons.In this study,we propose optical synthetic aperture imaging based on spatial intensity interferometry.This not only realizes diffraction-limited optical aperture synthesis in a single shot,but also enables imaging with a wide spectral bandwidth,which greatly improves the optical energy efficiency of intensity interferometry.And this method is insensitive to the optical path difference between the sub-apertures.Simulations and experiments present optical aperture synthesis diffraction-limited imaging through spatial intensity interferometry in a 100 nm spectral width of visible light,whose maximum optical path difference between the sub-apertures reaches 69λ.This technique is expected to provide a solution for optical aperture synthesis over kilometer-long baselines at optical wavelengths.

Intensity-Dependent Dipole Phase in High-Order Harmonic Interferometry

High-order harmonics are ideal probes to resolve the attosecond dynamics of strong-field recollision processes.An easy-to-implement phase mask is utilized to covert the Gaussian beam to TEM01 transverse electromagnetic mode,allowing the realization of two-source interferometry of high-order harmonics.We experimentally measure the intensity dependence of dipole phase directly with high-order harmonic interferometry,in which the driving laser intensity can be precisely adjusted.The classical electron excursion simulations reproduce the experimental findings quite well,demonstrating that Coulomb potential plays subtle roles on movement of electrons for harmonics near the ionization threshold.This work is of great importance for precision measurements of ultrafast dynamics in strong-field physics.

Measurement of Shear Stress Acting on Flat Plate Using Oil Film Interferometry

Measurements of frictional resistance play an important role in engineering practice. There are several types of air resistance acting on an aircraft, for example. One of them, frictional resistance, accounts for half of the air resistance. Oil film interferometry is one of methods for measuring the frictional resistance. Oil dropped on an object is thinly stretched by the frictional resistance. The bright and dark fringe pattern is generated when monochromatic light is applied to the oil film. The gradient of the oil thickness decreases with the lapse of time, and thus the spacing between neighboring the dark lines increases. The rate at which the spacing increases is proportional to the frictional resistance. In this study, the frictional resistance acting on a small area on a plate was measured and compared with the theoretical value. As a result, these results qualitatively agree well with each other.

Research on 3D marine electromagnetic interferometry with synthetic sources for suppressing the airwave interference

In order to suppress the airwave noise in marine controlled-source electromagnetic （CSEM） data, we propose a 3D deconvolution （3DD） interferometry method with a synthetic aperture source and obtain the relative anomaly coefficient （RAC） of the EM field reflection responses to show the degree for suppressing the airwave. We analyze the potential of the proposed method for suppressing the airwave, and compare the proposed method with traditional methods in their effectiveness. A method to select synthetic source length is derived and the effect of the water depth on RAC is examined via numerical simulations. The results suggest that 3DD interferometry method with a synthetic source can effectively suppress the airwave and enhance the potential of marine CSEM to hydrocarbon exploration.

Precise Three-Dimensional Deformation Retrieval in Large and Complex Deformation Areas via Integration of Offset-Based Unwrapping and Improved Multiple-Aperture SAR Interferometry:Application to the 2016 Kumamoto Earthquake

Conventional synthetic aperture radar(SAR)interferometry(InSAR)has been successfully used to precisely measure surface deformation in the line-of-sight(LOS)direction,while multiple-aperture SAR interferometry(MAI)has provided precise surface deformation in the along-track(AT)direction.Integration of the InSAR and MAI methods enables precise measurement of the two-dimensional(2D)deformation from an interferometric pair;recently,the integration of ascending and descending pairs has allowed the observation of precise three-dimensional(3D)deformation.Precise 3D deformation measurement has been applied to better understand geological events such as earthquakes and volcanic eruptions.The surface deformation related to the 2016 Kumamoto earthquake was large and complex near the fault line;hence,precise 3D deformation retrieval had not yet been attempted.The objectives of this study were to①perform a feasibility test of precise 3D deformation retrieval in large and complex deformation areas through the integration of offset-based unwrapped and improved multiple-aperture SAR interferograms and②observe the 3D deformation field related to the 2016 Kumamoto earthquake,even near the fault lines.Two ascending pairs and one descending the Advanced Land Observing Satellite-2(ALOS-2)Phased Array-type L-band Synthetic Aperture Radar-2(PALSAR-2)pair were used for the 3D deformation retrieval.Eleven in situ Global Positioning System(GPS)measurements were used to validate the 3D deformation measurement accuracy.The achieved accuracy was approximately 2.96,3.75,and 2.86 cm in the east,north,and up directions,respectively.The results show the feasibility of precise 3D deformation measured through the integration of the improved methods,even in a case of large and complex deformation.

APPLICATION OF 2-D MOIRE INTERFEROMETRYOF STICKING FILM IN HUMAN TIBIA MEASUREMENT

This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical path,the elastic constant,strain and displacement of the tibia are measured.Compared with the electric measuring method the error is samll and the sensitivity is high.

Comparative research and its significance of deformation measurements by technologies of laser real-time holographic interferome-try and radar differential interferometry

The principles and applications of laser real-time holographic interferometry （LRTHI） and radar differential interferometry （RDI） technologies are described in this paper, respectively. By using LRTHI, we can observe the deformation of samples under pressure in the lab and study the anomaly characteristics relating to different strain fields in different fracture-developing areas; while by using RDI, we can observe the landform and surface deformation. The results of deformation observed before and after the Ms=7.9 Mani earthquake （Tibet） and Ms=6.2 Shangyi-Zhangbei earthquake in China are obtained. It is pointed out that LRTHI and RDi are similar, which study the characteristics of anomalous deformation field by fringe variations for both of them. Therefore, the observation of deformation field in the seismogenic process, especially in the period impending an earthquake by RDI, and the comparative study in the lab by LRTHI are of great significance.

Review of Electronic Speckle Pattern Interferometry(ESPI) for Three Dimensional Displacement Measurement

Three dimensional（3D） displacements, which can be translated further into 3D strain, are key parameters tor design, manufacturing and quality control. Using different optical setups, phase-shift methods, and algorithms, several different 3D electronic speckle pattern interferometry（ESPl） systems for displacement and strain measurements have been achieved and commercialized. This paper provides a review of the recent developments in ESPI systems for 3D displacement and strain measurement. After an overview of the fundamentals of ESP! theory, temporal phase-shift, and spatial phase-shift techniques, 3D deformation measurements by the temporal phase-shift ESPI system, which is suited well for static measurement, and by the spatial phase-shift ESPI system, which is particularly useful for dynamic measurement, are discussed. For each method, the basic theory, a brief derivation and different optical layouts are presented. The state of art application, potential and limitation of the ESPI systems are shown and demonstrated.

Measurement of Liquid Concentration Fields Near Interface with Cocurrent Gas-Liquid Flow Absorption Using Holographic Interferometry

Real-time laser holographic interferometry was applied to measure liquid concentrations of CO2 in the vicinity of gas-liquid free interface under the conditions of cocurrent gas-liquid flow for absorption of CO2 by ethanol. The influences of the Reynolds number on the measurable interface concentration and on the film thickness were discussed. The results show that CO2 concentration decreases exponentially along the mass transfer direction,and the concentration gradient increases as Reynolds number of either liquid or gas increases. CO2 concentrations fluctuate slightly along the direction of flow; on the whole, there is an increase in CO2 concentration. The investigation also demonstrated that film thickness decreases with the increase of Reynolds number of either of the two phases. Sherwood number representing the mass transfer coefficient was finally correlated as a function of the hydrodynamic parameters and the physical properties.

Orbit optimization for ASTROD-GW and its time delay interferometry with two arms using CGC ephemeris

Astrodynamical space test of relativity using optical devices optimized for gravitation wave detection （ASTROD- GW） is an optimization of ASTROD to focus on the goal of detection of gravitation waves. The detection sensitivity is shifted 52 times toward larger wavelength compared with that of laser interferometer space antenna （LISA）. The mission orbits of the three spacecrafts forming a nearly equilateral triangular array are chosen to be near the Sun–Earth Lagrange points L3, L4, and L5. The three spacecrafts range interferometrically with one another with an arm length of about 260 million kilometers. In order to attain the required sensitivity for ASTROD-GW, laser frequency noise must be suppressed to below the secondary noises such as the optical path noise, acceleration noise, etc. For suppressing laser frequency noise, we need to use time delay interferometry （TDI） to match the two different optical paths （times of travel）. Since planets and other solar-system bodies perturb the orbits of ASTROD-GW spacecraft and affect the TDI, we simulate the time delay numerically using CGC 2.7 （here, CGC stands for center for gravitation and cosmology） ephemeris framework. To conform to the ASTROD-GW planning, we work out a set of 20-year optimized mission orbits of ASTROD-GW spacecraft starting at June 21, 2028, and calculate the differences in optical path in the first and second generation TDIs separately for one-detector case. In our optimized mission orbits of 20 years, changes of arm lengths are less than 0.0003 AU; the relative Doppler velocities are all less than 3m/s. All the second generation TDI for one-detector case satisfies the ASTROD-GW requirement.

Orbit optimization and time delay interferometry for inclined ASTROD-GW formation with half-year precession-period

ASTROD-GW （ASTROD [astrodynamical space test of relativity using optical devices] optimized for gravitational wave detection） is a gravitational-wave mission with the aim of detecting gravitational waves from massive black holes, extreme mass ratio inspirais （EMRIs） and galactic compact binaries together with testing relativistic gravity and probing dark energy and cosmology. Mission orbits of the 3 spacecrafts forming a nearly equilateral triangular array are chosen to be near the Sun-Earth Lagrange points L3, L4, and L5. The 3 space, crafts range interferometrically with one another with arm length about 260 million kilometers. For 260 times longer arm length, the detection sensitivity of ASTROD- GW is 260 fold better than that of eLISA/NGO in the lower frequency region by assuming the same acceleration noise. Therefore, ASTROD-GW will be a better cosmological probe. In previous papers, we have worked out the time delay interferometry （TDI） for the ecliptic formation. To resolve the reflection ambiguity about the ecliptic plane in source position determination, we have changed the basic formation into slightly inclined formation with half-year precessionperiod. In this paper, we optimize a set of 10-year inclined ASTROD-GW mission orbits numerically using ephemeris framework starting at June 21, 2035, including cases of inclination angle with 0° （no inclination）, 0.5°, 1.0°, 1.5°, 2.0°, 2.5°, and 3.0°. We simulate the time delays of the first and second generation TDI configurations for the different inclinations, and compare/analyse the numerical results to attain the requisite sensitivity of ASTROD-GW by suppressing laser frequency noise below the secondary noises. To explicate our calculation process for different inclination cases, we take the 1.0° as an example to show the orbit optimization and TDI simulation.

Monitoring elevation change of glaciers on Geladandong Mountain using Tan DEM-X SAR interferometry

Glaciers play an important role in the climate system. The elevation change of a glacier is an important parameter in studies of glacier dynamics. Only a few ground-based measurements of high mountain glaciers are available due to their remoteness, high elevation, and complex topography. The acquisition from the German Tan DEM-X(Terra SAR-X add-on for Digital Elevation Measurement) SAR imaging configuration provides a reliable data sources for studying the elevation change of glaciers. In this study, the bistatic Tan DEM-X data that cover the Geladandong Mountain on the Tibetan Plateau were processed with SAR interferometry technique and the elevation changes of the mountain's glaciers during 2000–2014 were obtained. The results indicated that although distinct positive and negative elevation changes were found for different glacier tongues, the mean elevation change was about-0.14±0.26 m a-1. Geoscience Laser Altimeter System(GLAS) data were obtained for comparison and verification. The investigation using GLAS data demonstrated the efficacy of the proposed method in determining glacier elevation change. Thus, the presented approach is appropriate for monitoring glacier elevation change and it constitutes a valuable tool for studies of glacier dynamics.

Comparison of four techniques for estimating temporal change of seismic velocity with passive image interferometry

Passive image interferometry （PII） is becoming a powerful tool for detecting the temporal variations in the Earth＇s structure, which applies coda wave interferometry to the waveforrns from the cross-correlation of seismic ambient noise. There are four techniques for estimating temporal change of seismic velocity with PII： moving-window cross-correlation technique （MWCCT）, moving-window cross-spectrum technique （MWCST）, stretching technique （ST） and moving-window stretching technique （MWST）. In this paper, we use the continuous seismic records from a typical station pair near the Wenchuan Ms8.0 earthquake fault zone and generate three sets of waveforms by stacking cross-correlation function of ambient noise with different numbers of days, and then apply four techniques to processing the three sets of waveforms and compare their results. Our results indicate that the techniques based on moving-window （MWCCT, MWCST and MWST） are superior in detecting the change of seismic velocity, and the MWCST can give a better estimate of velocity change than the other moving-window techniques due to measurement error. We also investigate the clock errors and their influences on measuring velocity change. We find that when the clock errors are not very large, they have limited impact on the estimate of the velocity change with the moving-window techniques.

Hole-drilling method using grating rosette and Moire interferometry

The hole-drilling method is one of the most wellknown methods for measuring residual stresses. To identify unknown plane stresses in a specimen, a circular hole is first drilled in the infinite plate under plane stress, then the strains resulting from the hole drilling is measured. The strains may be acquired from interpreting the Moire signature around the hole. In crossed grating Moire interferometry, the horizontal and vertical displacement fields （u and v） can be obtained to determinate two strain fields and one shearing strain field. In this paper, by means of Moire interferometry and three directions grating （grating rosette） developed by the authors, three displacement fields （u, v and s） are obtained to acquire three strain fields. As a practical application, the hole-drilling method is adopted to measure the relief strains for aluminum and fiber reinforced composite. It is a step by step method; in each step a single laminate or equivalent depth is drilled to find some relationships between the drilling depth and the residual strains relieved in the fiber reinforced composite materials.

STUDY ON FRACTURE BEHAVIOR OF FERROELECTRIC CERAMICS UNDER COMBINED ELECTROMECHANICAL LOADING BY USING A MOIR(?) INTERFEROMETRY TECHNIQUE

This paper discusses an in situ observation of fracture behavior around a crack tip in ferroelectric ceramics under combined electromechanical loading by use of a moiré interferometry technique.The deformation field induced by the electric field and the stress concentration near the crack tip in three-points bending experiments was measured.By analysis of the moiré images it is found that under a constant mechanical load,the electric field almost has no effect on the crack extension in the case that the directions of the poling,electric field and crack extension are perpendicular to each other.When the poling direction is parallel to the crack extension direction and perpendicular to the electric field,the strain decreases faster than that calculated by FEM with and without electrical loading as one goes away from the crack tip.In addition,as the electric field intensity increases,the strain near the crack tip increases,and the strain concentration becomes more significant.

Precision measurement with atom interferometry

Development of atom interferometry and its application in precision measurement are reviewed in this paper. The principle, features and the implementation of atom interferometers are introduced, the recent progress of precision measurement with atom interferometry, including determination of gravitational constant and fine structure constant, measurement of gravity, gravity gradient and rotation, test of weak equivalence principle, proposal of gravitational wave detection, and measurement of quadratic Zeeman shift are reviewed in detail. Determination of gravitational redshift, new definition of kilogram, and measurement of weak force with atom interferometry are also briefly introduced.

Monitoring subsidence rates along road network by persistent scatterer SAR interferometry with high-resolution TerraSAR-X imagery

Ground subsidence is one of the key factors damaging transportation facilities, e.g., road networks consisting of highways and railways. In this paper, we propose to apply the persistent scatterer synthetic aperture radar interferometry （PS-InSAR） approach that uses high- resolution TerraSAR-X （TSX） imagery to extract the regional scale subsidence rates （i.e., average annual sub- sidence in mm/year） along road networks. The primary procedures involve interferometric pair selection, interfer- ogram generation, persistent scatterer （PS） detection, PS networking, phase parameterization, and subsidence rate estimation. The Xiqing District in southwest Tianjin （China） is selected as the study area. This district contains one railway line and several highway lines. A total of 15 TSX images covering this area between April 2009 and June 2010 are utilized to obtain the subsidence rates by using the PS-InSAR （PSI） approach. The subsidence rates derived from PSI range from -68.7 to -1.3 mm/year. These findings show a significantly uneven subsidence pattern along the road network. Comparison between the PSI-derived subsidence rates and the leveling data obtained along the highways shows that the mean and standard deviation （SD） of the discrepancies between the two types of subsidence rates are 0.1 and 4-3.2 mm/year, respectively. The results indicate that the high-resolution TSX PSI is capable of providing comprehensive and detailed subsidence information regarding road networks with millimeter-level accuracy. Further inspections under geo- logical conditions and land-use categories in the study area indicate that the observed subsidence is highly related to aquifer compression due to groundwater pumping. Therefore, measures should be taken to mitigate groundwater extraction for the study area.