STEADY-STATE AND IDLE OPTIMIZA-TION OF INTERNAL COMBUSTION ENGINE CONTROL STRATEGIES FOR HYBRID ELECTRIC VEHICLES

A novel steady-state optimization （SSO） of internal combustion engine （ICE） strategy is proposed to maximize the efficiency of the overall powertrain for hybrid electric vehicles, in which the ICE efficiency, the efficiencies of the electric motor （EM） and the energy storage device are all explicitly taken into account. In addition, a novel idle optimization of ICE strategy is implemented to obtain the optimal idle operating point of the ICE and corresponding optimal parking generation power of the EM using the view of the novel SSO of ICE strategy. Simulations results show that potential fuel economy improvement is achieved relative to the conventional one which only optimized the ICE efficiency by the novel SSO of ICE strategy, and fuel consumption per voltage increment decreases a lot during the parking charge by the novel idle optimization of ICE strategy.

Non-linear Torsional Vibration Characteristics of an Internal Combustion Engine Crankshaft Assembly

Crankshaft assembly failure is one of the main factors that affects the reliability and service life of engines.The linear lumped mass method,which has been universally applied to the dynamic modeling of engine crankshaft assembly,reveals obvious simulation errors.The nonlinear dynamic characteristics of a crankshaft assembly are instructionally significant to the improvement of modeling correctness.In this paper,a general expression for the non-constant inertia of a crankshaft assembly is derived based on the instantaneous kinetic energy equivalence method.The nonlinear dynamic equations of a multi-cylinder crankshaft assembly are established using the Lagrange rule considering nonlinear factors such as the non-constant inertia of reciprocating components and the structural damping of shaft segments.The natural frequency and mode shapes of a crankshaft assembly are investigated employing the eigenvector method.The forced vibration response of a diesel engine crankshaft assembly taking into account the non-constant inertia is studied using the numerical integral method.The simulation results are compared with a lumped mass model and a detailed model using the system matrix method.Results of non-linear torsional vibration analysis indicate that the additional excitation torque created by non-constant inertia activates the 2nd order rolling vibration,and the additional damping torque resulting from the non-constant inertia is the main nonlinear factor.The increased torsional angular displacement evoked by the high order excitation torque relates to the non-constant inertia.This research project is aimed at improving nonlinear dynamics theory,and the confirmed nonlinear parameters can be used for the structure design of a crankshaft assembly.

Kinetic models of natural gas combustion in an internal combustion engine

In this study, combustion of methane was simulated using four kinetic models of methane in CHEMKIN 4.1.1 for 0-D closed internal combustion （IC） engine reactor. Two detailed （GRIMECH3.0 ＆ UBC MECH2.0） and two reduced （One step ＆ Four steps） models were examined for various IC engine designs. The detailed models （GRIMECH3.0, ＆ UBC MECH2.0） and 4-step models successfully predicted the combustion while global model was unable to predict any combustion reaction. This study illustrated that the detailed model showed good concordances in the prediction of chamber pressure, temperature and major combustion species profiles. The detailed models also exhibited the capabilities to predict the pollutants formation in an IC engine while the reduced schemes showed failure in the prediction of pollutants emissions. Although, there are discrepancies among the profiles of four considered model, the detailed models （GRIMECH3.0 ＆ UBC MECH2.0） produced the acceptable agreement in the species prediction and formation of pollutants.

NO_x emission characteristics of hydrogen internal combustion engine

To study the economic advantages of hydrogen internal combustion engine, an experimen- tal study was carried out using a 2.0 L port fuel-injected （PFI） hydrogen internal combustion engine. Influences of fuel-air equivalence ratio φ, speed, and ignition advance angle on heat efficiency were determined. Test results showed that indicated thermal efficiency （ ITE ） firstly increased with fuel- air equivalence ratio, achieved the maximum value of 40. 4% （ φ = 0.3 ）, and then decreased when was more than 0. 3. ITE increased as speed rises. Mechanical efficiency increased as fuel-air equiva- lence ratio increased, whereas mechanical efficiency decreased as speed increased, with maximum mechanical efficiency reaching 90%. Brake thermal efficiency （BTE） was influenced by ITE and me- chanical efficiency, at the maximum value of 35% （φ =0.5, 2 000 r/min）. The optimal ignition ad- vance angle of each condition resulting in the maximum BTE was also studied. With increasing fuel- air equivalence ratio, the optimal ignition angle became closer to the top dead center （ TDC ）. The test results and the conclusions exhibited a guiding role on hydrogen internal combustion engine opti- mization.

Application of non-equal interval GM(1,1)model in oil monitoring of internal combustion engine

The basic difference non-equal interval model GM(1,1) in grey theory was used to fit and forecast data series with non-equal lengths and different inertias, acquired from oil monitoring of internal combustion engines. The fitted and forecasted results show that the length or inertia of a sequence affects its precision very much, i.e. the bigger the inertia of a sequence is, or the shorter the length of a series is, the less the errors of fitted and forecasted results are. Based on the research results, it is suggested that short series should be applied to be fitted and forecasted; for longer series, the newer datum should be applied instead of the older datum to be analyzed by non- equalinterval GM(1,1) to improve the forecasted and fitted precision, and that data sequence should be verified to satisfy the conditions of grey forecasting.

Research on Simulation and Prediction of Internal Combustion Engine Structural Acoustic Radiation

With the purpose of efficiently predicting structural radiated noise of internal combustion engine（I.C.E.）,a new simulation technique is introduced,which is an approach based on boundary element method （BEM）,acoustic transfer vector（ATV） technique and coupled boundary element model and finite element model （BEM-FEM） approach.Analyses of vibration exciting loads,computing structural dynamic characteristics and dynamic responses have led to theoretical results,which are tested on an L6 diesel engine to validate this proposed technique in engineering practice.

Effect of Nozzle Inclination Angle on Fuel-Air Mixing and Combustion in a Heavy Fuel Engine

Heavy-fuel engines are widely used in UAVs(Unmanned Autonomous Vehicles)because of their reliability and high-power density.In this study,a combustion model for an in-cylinder direct injection engine has been imple-mented using the AVL FIRE software.The effects of the angle of nozzle inclination on fuel evaporation,mixture distribution,and combustion in the engine cylinder have been systematically studied at 5500 r/min and consider-ing full load cruise conditions.According to the results,as the angle of nozzle inclination increases,the maximum combustion explosion pressure in the cylinderfirst increases and then it decreases.When the angle of nozzle incli-nation is less than 45°,the quality of the mixture in the cylinder and the combustion performance can be improved by increasing the angle.When the angle of nozzle inclination is greater than 45°,however,the mixture unevenness increases slightly with the angle,leading to a deterioration of the combustion performances.When the angle of nozzle inclination is between 35°and 55°,the overall combustion performance of the engine is rela-tively good.When the angle of nozzle inclination is 45°,the combustion chamber’s geometry and the cylinder’s airflow are well matched with the fuel spray,and the mixture quality is the best.Compared with 25°,the peak heat release rate increases by 20%,and the maximum combustion burst pressure increases by 5.5%.

On the Design and Optimization of a Clean and Efficient Combustion Mode for Internal Combustion Engines through a Computer NSGA-Ⅱ Algorithm

In order to address typical problems due to the huge demand of oil for consumption in traditional internal combustion engines,a new more efficient combustion mode is proposed and studied in the framework of Computational Fluid Dynamics(CFD).Moreover,a Non-dominated Sorting Genetic Algorithm(NSGA-Ⅱ)is applied to optimize the related parameters,namely,the engine methanol ratio,the fuel injection time,the initial temperature,the Exhaust Gas Re-Circulation(EGR)rate,and the initial pressure.The so-called Conventional Diesel Combustion(CDC),Homogeneous Charge Compression Ignition(HCCI)and the Reactivity Controlled Compression Ignition(RCCI)combustion modes are compared.The results show that RCCI has a higher methanol ratio and an earlier injection timing with moderate EGR rate and higher initial pressure.The initial temperature increases as the methanol ratio increases.In comparison,CDC has the lowest hydrocarbon and CO emissions and the highest combustion efficiency.At different crankshaft rotation angles corresponding to 50%of the combustion amount(CA50),the combustion temperature and boundary layer temperature of HCCI change significantly,while those of RCCI undergo limited variations.At the same CA50,the exergy losses of HCCI and RCCI are lower than that of the CDC.On the basis of these findings,it can be concluded that the methanol/diesel RCCI engine can be used to obtain a clean and efficient combustion process,which should be regarded as a promising combustion mode.

The Effect of Ignition Parameters on the Combustion Characteristics of an Aviation Piston Engine

A cylinder combustion simulation model was established for a two-stroke aviation piston engine used in a small unmanned aerial vehicle. The influence of different ignition system parameters on the combustion process of aviation kerosene was studied using this model. The research results showed that under the working conditions of 5500 r/min and 50% throttle opening, as the ignition energy increased, the peak values of average cylinder pressure and average temperature increased, and the combustion duration shortened, The advance of the combustion center of gravity increases the tendency of the engine to knock. Under the same operating conditions, as the ignition timing advances, the peak values of average pressure and average temperature in the cylinder increase, gradually approaching the top dead center, and the tendency of engine detonation increases more significantly.

Performance, Combustion and Emission Characteristics of Oxygenated Diesel in DI Engines: A Critical Review

The transition from non-renewable to renewable energy sources is a significant challenge of our time. In the fuel industry, oxygenated additives such as butanol are transforming conventional fuels into renewable biofuels. This technology has been utilized in reciprocating engines for decades. This paper reviews the viability of using an n-butanol blend as a short-term replacement for diesel by analyzing its physical and chemical properties, combustion, performance, and emission characteristics in compression ignition (CI) engines under various conditions, including variable load, speed, acceleration, and both stationary and transient cycles. N-Butanol exhibits higher viscosity, better lubricity, higher heating value, improved blend stability, enhanced cold-flow properties, and higher density. These factors influence spray formation, injection timing, atomization, and combustion characteristics. Its higher oxygen content improves the diffusion combustion stage and efficiency. Adding 5% and 10% n-butanol to diesel increases pressure and apparent heat release rate, slightly reduces temperature, and improves thermal efficiency, with mixed effects on CO and THC emissions and a notable decrease in particulate matter emissions. Fuel consumption increases, while the impact on NOx emissions varies. A 10% butanol blend is considered optimal for enhancing performance and reducing particulate emissions without significantly affecting NOx emissions. Blending up to 40% butanol with diesel does not require engine modifications or ECU recalibrations in engines calibrated for pure diesel. Due to its advantageous properties and performance, n-butanol is recommended as a superior alcohol-diesel blend than ethanol for short-term diesel replacement.

Thermal Aspects in Lubrication System Design for Internal Combustion Engines

The mechanical losses in an internal combustion engine cause a significant decrease in the engine’s overall efficiency. Wherever friction work is dissipated a heat load will inevitably appear. This heat load has to be taken care of in some way, usually with both the water-cooling and the lubrication system. Despite its name, one of the major tasks of the latter one is, to draw out heat from between lubricated surfaces. In contrast to the water cooling system, which is primarily designed for cooling the cylinder block, the lubrication system is mainly required for cooling the crankshaft and piston rod bearings. A lubrication system for today’s automotive engines consists of several components, i.e. an oil pump, a pressure relief valve and an oil filter. This study focuses on the dynamic characteristics of a pressure relief valve and how the system temperature is affected by the critical design parameters of the valve. Using a thermodynamic simulation model together with an optimisation strategy makes it possible to express the desired system characteristics. Then, the optimisation strategy seeks for a similar system configuration with help of the model.

Development of Valve Steel for Internal Combustion Engine in China

This paper first briefly introduces the history of the development of China valve steel from mainly adopting valve steel from the former Soviet Uinoin in the fifties, manufacturing by herself in the sixties, to introducing advanced valve steel from other countries and instituting Chinese valve steel system since the seventies.The demand of valve steel for China internal combustion engine including material specification and quantity required at present is discussed. The principal difficulties being faced with in the development of China valve steel at the moment are put forward. Finally, a detailed discussion is made on the development of China valve steel with suggstions of developing 5Cr8Si2 and MF811 martensitic steels, 21 2N austenitic steel used for gasoline engine, 23 8N austenitic steel used for diesel engine, 21 4NWNb high strength austenitic steel and LF2 and LF4 for valve alloy.[WT5”BZ〗

Improvement on Performances of Internal Combustion Engine Using the Technology of Ceramic Coating

This paper introduces a new technology of using ceramic coating on piston rings of an internal combustion engine, and the comparison of mechanical efficiency and performances of an actual engine before and after the application of ceramic coating on the piston rings. The experimental results show that the mechanical efficiency and power output are enhanced by 4% and 2.6%, respectively, with fuel consumption reduced by (2.9%.) Further studies on coating processing and coating materials as well as the reliability and durability will be of great significance in the application and popularization of the new technology.

Establishment of a CouplingModel for the Prediction of Heat Dissipation of the Internal Combustion Engine Based on Finite Element

The aerodynamics and heat transfer performance in the rear-mounted automobile cabin have an important influence on the engine’s safety and the operational stability of the automobile.The article uses STARCCM and GT-COOL software to establish the 3D wind tunnel model and engine cooling system model of the internal combustion engine.At the same time,we established a 3D artificial coupling model through parameter transfer.The research results show that the heat transfer coefficient decreases with the increase of the comprehensive drag coefficient of the nacelle.This shows that the cabin flow field has an important influence on the heat transfer coefficient.Themainstream temperature rise of the engine room increases with the increase of the engine load.It is proved that vehicle speed affects the amount of heat dissipation of the engine room internal combustion engine under certain load conditions.The article provides a more effective and fast calculation method for the research on the heat dissipation of the internal combustion engine and the optimization of the cooling system equipment.

Influence of Internal Combustion Engine Parameters on Gas Leakage through the Piston Rings Area

In this work, the influence of internal combustion engine parameters (cylinder-piston clearance, piston head height, the first segment position, gap of the first piston ring and gap of the second piston ring, piston rings’ axial clearance, intake valve debit coefficient) gas leakage from the combustion chamber through the piston rings’ area was investigated. This influence was studied by making an initial forming operation over gas leakage in the analyzed area.

Research on Measurements for Temperature and Stress of Pistons in Internal Combustion Engine

In both numerical simulation and experimental research for the piston of internal combustion engine, the verification foundations are always insufficient. The reason is the measurements for its transient temperature and stress under actual operation conditions are very difficult. A multi-channel measurement-storage technology is used in the engine bench experiment to measure the piston temperature and stress in real time. The temperature and stress changes in the engine operation process are obtained. They provide reliable instructive criteria for numerical analysis and experiment of the piston working state.

Fault Identification of Internal Combustion Engine based on Support Vector Machine and Fuzzy Neural Network

The internal combustion engine is the main power source of current large⁃scale machinery and equipment.Overhaul and maintenance of its faults are important conditions for ensuring the safe and stable operation of machinery and equipment,and the identification of faults is a prerequisite.Therefore,the fault identification of internal combustion engines is one of the important directions of current research.In order to further improve the accuracy of the fault recognition of internal combustion engines,this paper takes a certain type of internal combustion engine as the research object,and constructs a support vector machine and a fuzzy neural network fault recognition model.The binary tree multi⁃class classification algorithm is used to determine the priority,and then the fuzzy neural network is verified.The feasibility of the model is proved through experiments,which can quickly identify the failure of the internal combustion engine and improve the failure processing efficiency.

Influence of Valve's Characteristic on Total Performance of Three Cylinders Internal Combustion Water Pump

Intenal combustion pump （ICP） is a new type power device turning the thermal energy from fuel combustion into fluid pressure energy. Three cylinders prototype has just been developed. The study on the influence of valve＇s characteristic on ICP＇s total performance will found the base for its optimum design. Based on the theoretical and testing fruits of single cylinder prototype, the performance of the valves and complete appliance of the latest is simulated. When the natural frequency of valves is approximately to the round number times of the working frequency, volumetric efficiency is seriously low. The nominal rotational speed of the prototype is nearly to the speed where the volumetric efficiency is lowest, which is harmful to the normal work of ICP, so further structure optimization of valves should be carried out. The change of volumetric efficiency has great influence on the fuel consumption rate, output flow, effective thermal efficiency, effective power, and so on, but little on output pressure.

Simulation and Experiment for Oxygen-enriched Combustion Engine Using Liquid Oxygen to Solidify CO2

For capturing and recycling of CO2 in the internal combustion engine, Rankle cycle engine can reduce the exhaust pollutants effectively under the condition of ensuring the engine thermal efficiency by using the techniques of spraying water in the cylinder and optimizing the ignition advance angle. However, due to the water spray nozzle need to be installed on the cylinder, which increases the cylinder head design difficulty and makes the combustion conditions become more complicated. In this paper, a new method is presented to carry out the closing inlet and exhaust system for internal combustion engines. The proposed new method uses liquid oxygen to solidify part of cooled CO2 from exhaust system into dry ice and the liquid oxygen turns into gas oxygen which is sent to inlet system. The other part of CO2 is sent to inlet system and mixed with oxygen, which can reduce the oxygen-enriched combustion detonation tendency and make combustion stable. Computing grid of the IP52FMI single-cylinder four-stroke gasoline-engine is established according to the actual shape of the combustion chamber using KIVA-3V program. The effects of exhaust gas recirculation （EGR） rate are analyzed on the temperatures, the pressures and the instantaneous heat release rates when the EGR rate is more than 8%. The possibility of enclosing intake and exhaust system for engine is verified. The carbon dioxide trapping device is designed and the IP52FMI engine is transformed and the CO2 capture experiment is carried out. The experimental results show that when the EGR rate is 36% for the optimum EGR rate. When the liquid oxygen of 35.80-437.40 g is imported into the device and last 1-20 min, respectively, 21.50-701.30 g dry ice is obtained. This research proposes a new design method which can capture CO2 for vehicular internal combustion engine.