Ultrasonic sensitivity-improved fiber-optic Fabry-Perot interferometer using a beam collimator and its application for ultrasonic imaging of seismic physical models

An ultrasonic sensitivity-improved fiber-optic Fabry-Perot interferometer （FPI） is proposed and employed for ultra- sonic imaging of seismic physical models （SPMs）. The FPI comprises a flexible ultra-thin gold film and the end face of a graded-index multimode fiber （MMF）, both of which are enclosed in a ceramic tube. The MMF in a specified length can collimate the diverged light beam and compensate for the light loss inside the air cavity, leading to an increased spectral fringe visibility and thus a steeper spectral slope. By using the spectral sideband filtering technique, the collimated FP1 shows an improved ultrasonic response. Moreover, two-dimensional images of two SPMs are achieved in air by recon- structing the pulse-echo signals through using the time-of-flight approach. The proposed sensor with easy fabrication and compact size can be a good candidate for high-sensitivity and high-precision nondestructive testing of SPMs.

Utilization of Extrinsic Fabry-Perot Interferometers with Spectral Interferometric Interrogation for Microdisplacement Measurement

The paper presents a number of signal processing approaches for the spectral interferometric interrogation of extrinsic Fabry-Perot interferometers(EFPIs). The analysis of attainable microdisplacement resolution is performed and the analytical equations describing the dependence of resolution on parameters of the interrogation setup are derived. The efficiency of the proposed signal processing approaches and the validity of analytical derivations are supported by experiments. The proposed approaches allow the interrogation of up to four multiplexed sensors with attained resolution between 30 pm and 80 pm, up to three times improvement of microdisplacement resolution of a single sensor by means of using the reference interferometer and noisecompensating approach, and ability to register signals with frequencies up to 1 kHz in the case of 1 Hz spectrum acquisition rate. The proposed approaches can be used for various applications, including biomedical, industrial inspection, and others, amongst the microdisplacement measurement.

Coulomb-Dominated Oscillations in Fabry-Perot Quantum Hall Interferometers

Periodic resistance oscillations in Fabry-Perot quantum Hall interferometers are observed at integer filling factors of the constrictions, fc=1, 2, 3, 4, 5 and 6. Rather than the Aharonov-Bohm interference, these oscillations are attributed to the Coulomb interactions between interfering edge states and localized states in the central island of an interferometer, as confirmed by the observation of a positive slope for the lines of constant oscillation phase in the image plot of resistance in the 13 Vs plane. Similar resistance oscillations are also observed when the area A of the center regime and the backseattering probability of interfering edge states are varied, by changing the side-gate voltages and the configuration of the quantum point contacts, respectively. The oscillation amplitudes decay exponentially with temperature in the ramge of 40mK〈 T ≤ 130 mK, with a characteristic temperature T0 -25 mK, consistent with recent theoretical and experimental works.

Integrated Fabry–Perot interferometer based on Er/Yb co-doped fiber for all-optical phase modulation

Fast and stable phase control is essential for many applications in optics. Here, we propose an all-fiber all-optical phase modulation scheme based on a Fabry–Perot interferometer(FPI) and an Er/Yb co-doped fiber(EYDF). By using the EYDF as an F-P cavity via rational design, a phase shift with a modulation sensitivity of 0.0312π/mW is introduced to the modulator.The phase shifts in the EYDF consist of a thermal phase shift and a nonlinear phase shift with a ratio of 19:1, and the corresponding temporal responses of the modulation are 204 ms and 2.5 ms, respectively. In addition, the compact FPI is encapsulated to provide excellent stability for the modulator.

Fiber Fabry-Perot Demodulation System Based on Dual Fizeau Interferometers

In this study,we present a dual-Fizeau-interferometer-based high-speed and wide-range fiber-optic Fabry-Perot(F-P)demodulation system.We employ two Fizeau interferometers with air cavity thickness satisfying the quadrature requirement to increase the demodulation speed and broaden the demodulation range in order to address the issues of the existing fiber F-P demodulation system's sluggish demodulation rate and limited range.In order to investigate the demodulation properties of the dual-Fizeau-interferometer-based demodulation system,we derive and create a theoretical model of the system.The theoretical model,which primarily consists of the structural design of the interferometer and the study of the center wavelength of the light sources and their bandwidth selection,is used to construct the optical structure of the demodulation system.According to the calculation results,the demodulated signal exhibits the best contrast ratio when the two light sources'respective center wavelengths are 780nm and 850nm,and their bandwidths are 28nm and 30 nm.Finally,we finish evaluating the demodulation system's demodulation performance,parameter calibration,and assembly debugging.The test results demonstrate the constant operation of the demodulation system,an update rate of 100kHz,a demodulation range of 4.74μm,and a cavity length resolution of approximately 5 nm.Additionally,the system can perform high speed demodulation thanks to the light emitting diode's(LED's)nanosecond level switching speed and the usage of a single point detector.

Fabrication and sensing characteristics of intrinsic Fabry–Perot interferometers in fiber tapers

This Letter presents intrinsic Fabry–Perot interferometers in the fiber tapers fabricated by the femtosecond laser micromachining technique. The sensing of temperatures as high as 1000°C based on the fiber device is characterized, with a sensitivity of 15.28 pm∕°C. A nearly linear refractive index sensing is also obtained by using the fringe visibility to characterize, with a sensitivity of 73.05 dB∕RIU. These intrinsic Fabry–Perot interferometers in fiber tapers may be useful in applications of high-temperature and linear refractive index sensing.

Application of Wavelet Transform in Dual-differential Optical Fiber F-P Interferometric Micro-displacement Measurement System

Based on dual-differential comparing principle, an experimental system of optical fiber F-P interferometric micro-displacement measurement is introduced. It is capable of achieving the absolute displacement measurement, and wavelet transforms is adopted as theory fundament to extract the optical F-P interferometric characteristic signal and remove the noise, so its resolution can reach 0. 01 μm in the dynamic range of 0～ 1 mm.

Pressure Sensor Based on the Fiber-Optic Extrinsic Fabry-Perot Interferometer

Pressure sensors based on fiber-optic extrinsic Fabry-Perot interferometer(EFPI)have been extensively applied in various industrial and biomedical fields.In this paper,some key improvements of EFPI-based pressure sensors such as the controlled thermal bonding technique,diaphragm-based EFPI sensors,and white light interference technology have been reviewed.Recent progress on signal demodulation method and applications of EFPI-based pressure sensors has been introduced.Signal demodulation algorithms based on the cross correlation and mean square error(MSE)estimation have been proposed for retrieving the cavity length of EFPI.Absolute measurement with a resolution of 0.08 nm over large dynamic range has been carried out.For downhole monitoring,an EFPI and a fiber Bragg grating(FBG)cascade multiplexing fiber-optic sensor system has been developed,which can operate in temperature 300℃with a good long-term stability and extremely low temperature cross-sensitivity.Diaphragm-based EFPI pressure sensors have been successfully used for low pressure and acoustic wave detection.Experimental results show that a sensitivity of 31 mV/Pa in the frequency range of 100 Hz to 12.7 kHz for aeroacoustic wave detection has been obtained.

Generation of millimeter-wave sub-carrier optical pulse by using a Fabry-Perot interferometer

A novel scheme is proposed to transform a Gaussian optical pulse to a millimeter-wave （mm-wave） frequency modulation pulse by using a Fabry-Perot interferometer （FPI） for radio-over-fiber （ROF） system. It is shown that modulation frequency of mm-wave is determined by the optical path of the Fabry-Perot （F-P） cavity, and amplitude decay time and energy transfer efficiency axe related to the reflectivity of the F-P cavity mirror. The effect of pulse train extension on inter-symbol interference is also discussed.

An Extrinsic Fiber Fabry-Perot Interferometer for Dynamic Displacement Measurement

A versatile fiber interferometer was proposed for high precision measurement. The sensor exploited a double-cavity within the unique sensing arm of an extrinsic-type fiber Fabry-Perot interferometer to produce the quadrature phase-shifted interference fringes. Interference signal processing was carried out using a modified zero-crossing （fringe） counting technique to demodulate two sets of fringes. The fiber interferometer has been successfully employed for dynamic displacement measurement under different displacement profiles over a range of 0.7 p.m to 140 p.m. A dedicated computer incorporating the demodulation algorithm was next used to interpret these detected data as well as plot the displacement information with a resolution of 2/64. A commercial displacement sensor was employed for comparison purposes with the experimental data obtained from the fiber interferometer as well as to gauge its performance, resulting in the maximum error of 2.8% over the entire displacement range studied.

Zeolite Thin Film-Coated Fiber Sensors Based on Fabry-Perot Interferometer for Detection of Chemical Vapors

A novel zeolite-coated fiber sensors for detection of volatile organic compounds （VOCs） based on the Fabry-Perot interferometer was proposed and demonstrated. The sensor comprised a polycrystalline silicalite thin film grown up on the cleaved end face of a standard single-mode fiber. The inline Fabry-Perot cavity was composed by the end face of the single-mode fiber and the thin film. The sensor device operated by measuring the interference signal, which was a function of the amount of chemical vapor adsorption in its crystalline micro porous structure. Experimental results showed that the proposed VOC sensor worked well and the sensitivities were 2.78×10^-3dB/ppm when the concentration ranged from 350ppm to 2100ppm and 1.23×10^-3 dB/ppm when the concentration ranged from 2100ppm to 5250 ppm.

Fiber Fabry-Perot Interferometer for Curvature Sensing

A curvature sensor based on an Fabry-Perot （FP） interferometer was proposed. A capillary silica tube was fusion spliced between two single mode fibers, producing an FP cavity. Two FP sensors with different cavity lengths were developed and subjected to curvature and temperature. The FP sensor with longer cavity showed three distinct operating regions for the curvature measurement. Namely, a linear response was shown for an intermediate curvature radius range, presenting a maximum sensitivity of 68.52 pm/m-1. When subjected to temperature, the sensing head produced a similar response for different curvature radii, with a sensitivity varying from 0.84 pm/℃ to 0.89 pm/℃, which resulted in a small cross-sensitivity to temperature when the FP sensor was subjected to curvature. The FP cavity with shorter length presented low sensitivity to curvature.

Sinusoidal Phase-Modulating Fabry-Perot Interferometer for Angular Displacement Measurement

In this paper, a sinusoidal phase-modulating Fabry-Perot interferometer is proposed to measure angular displacement. The usefulness of the interferometer is demonstrated by simulations and experiments.

Study of the Sensing Characteristics of Irradiated Fiber Bragg Gratings and Fabry-Perot Interferometers Under Gamma Radiation

The sensing characteristics of irradiated fiber Bragg gratings(FBGs)and Fabry-Perot interferometers(FPIs)were investigated under a 2MGy dose of gamma radiation.The study found that the pressure sensitivity of FP sensors after irradiation was stable,while the temperature sensitivity of FBG sensors was unstable,and both wavelengths displayed a shift.These findings offer the possibility for the application of FP pressure sensors in the gamma radiation environments,and FBG sensors require further research to be suitable for application in the nuclear radiation environments.

Nanostrain Measurement Using Chirped Bragg Grating Fabry-Perot Interferometer

A simple nanostrain direct current （DC） measurement system based on a chirped Bragg grating Fabry-Perot （FP） structure is presented. The FP cavity, formed between the chirped fiber Bragg grating （CFBG） and the fiber end face, presents an aperiodic behavior due to the CFBG. A laser located in the fringe pattern slope is used to interrogate the sensing head. The optical power parameter is analyzed when strain is applied, for long and short period fringe pattern wavelengths, and sensitivities of-2.87 μW/με and-5.48μW/με are respectively obtained. This configuration presents a resolution of 70 ε.

The technique of detecting the laser-ultrasonic vector displacement with a confocal Fabry-Perot interferometer waves in a plate

Generally, a confocal Fabry-Perot interferometer is only able to detect the out-of-plane component of a displacement field; while the in-plane component often has the information about the material which cannot be found in this out-of-plane component. In this paper, based on a confocal Fabry-Perot interferometer set-up for detecting the out-of-plane component of a laser generated acoustic field, a technique is developed to detect both the out-of-plane and in-plane displacement components simultaneously with a novel two-channel confocal Fabry-Perot interferometer.

Photonic Crystal Fiber Fabry-Perot Interferometers With High-Reflectance Internal Mirrors

We demonstrated an in-line micro fiber-optic Fabry-Perot interferometer with an air cavity which was created by multi-step fusion splicing a muti-mode photonic crystal fiber （MPCF） to a standard single mode fiber （SMF）. The fringe visibility of the interference pattern was up to 20 dB by reshaping the air cavity. Experimental results showed that such a device could be used as a highly sensitive strain sensor with the sensitivity of 4.5 pm/με. Moreover, it offered some other outstanding advantages, such as the extremely compact structure, easy fabrication, low cost, and high accuracy.

Recent Progress in Multiparameter Measurement Based on Extrinsic Fiber-Optic Fabry-Perot Interferometers and Fiber Gratings

This paper presents a review of recent progress in simultaneous measurement of multiparameters including strain, temperature, vibration, transverse load, based on the combinations of extrinsic fiber-optic Fabry-Perot interferometers and fiber gratings.

A novel time-to-live countdown scheme based on asymmetric Mach-Zehnder interferometer and Fabry-Perot semiconductor optical amplifier

We propose a novel optical time-to-live （TTL） processing scheme using asymmetric Mech-Zehnder inter-ferometer （AMZI） and Fabry-Perot semiconductor optical amplifier （FP-SOA）. AMZI transfers M TTL pulses into M-1 pulses and two residual pulses with 6-dB power difference. FP-SOA enhances the power difference between the M - 1 pulses to the residual pulses to more than 10 dB. A numerical model is established for verifying the feasibility of this scheme.

基于光纤法布里——珀罗干涉仪的温度传感器

提出了一种基于光纤法布里—珀罗(F-P)干涉仪的温度传感器,传感器的敏感部分是一段两端研磨为平面的单模光纤,它的一端与一根单模传光光纤相接以形成一个反射面,另一端与空气接触形成另一个反射面,这两个反射面与敏感部分光纤形成本征光纤F-P干涉仪(IFPI)。分析了该光纤温度传感器的温度响应特性,制作了传感器原理样机,搭建了测试平台,并对原理样机进行了测试。在25~30℃的范围内对传感器进行了标定,测得温度响应灵敏度为21.504·2πrad/℃,温度分辨率为0.046℃。实验结果表明:该传感器对温度有较好的线性响应和较高的灵敏度,且制作工艺简单,成本低,具有良好的应用前景。