Inversion method of deflection of the vertical based on SWOT wide-swath altimeter data

The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian component.To obtain higher accuracy and resolution of ocean gravity information,researchers have proposed a novel altimeter called the wide-swath altimeter.This altimeter allows for the simultaneous acquisition of high-precision and high-resolution two-dimensional measurements of sea surface height(SSH).In this paper,the Surface Water and Ocean Topography(SWOT)mission with a wide-swath altimeter on board is selected for research.One cycle of swoT sea surface height data is simulated to inverse the DOV in the Arabian Sea(45°E—80°E,0°-30°N),and the inversion results are compared with those of conventional altimeter data.The results demonstrate that the difference between the meridian and prime components derived from the inversion of swoT wide-swath data is minimal,significantly outperforming the inversion results of conventional nadir altimeter data.The advantage of swoT wide-swath altimeter lies in its ability to use the multi-directional geoid slope at any sea surface measurement point to invert the components in the meridian and prime directions.To investigate the impact of this advantage on inversion precision,this paper employs a method to calculate the gradient of the geoid in multiple directions to invert DoV components.The improvement effect of calculating the gradient of the geoid in multiple directions on the precision of DoV component is analyzed.It is found that the accuracy of DoV inversion has significantly improved with the increase of geodetic gradient calculation direction.In addition,the effects of various errors and grid spacing in SwoT wide sea surface height data on the precision of Dov inversion are also analyzed.

An empirical method for joint inversion of wave and wind parameters based on SAR and wave spectrometer data

Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea surface phenomena.SAR systems,for instance,are hindered by an azimuth cut-off phenomenon in sea surface wind field observation.Wave spectrometers,while unaffected by the azimuth cutoff phenomenon,struggle with low azimuth resolution,impacting the capture of detailed wave and wind field data.This study utilizes SAR and surface wave investigation and monitoring(SWIM)data to initially extract key feature parameters,which are then prioritized using the extreme gradient boosting(XGBoost)algorithm.The research further addresses feature collinearity through a combined analysis of feature importance and correlation,leading to the development of an inversion model for wave and wind parameters based on XGBoost.A comparative analysis of this model with ERA5 reanalysis and buoy data for of significant wave height,mean wave period,wind direction,and wind speed reveals root mean square errors of 0.212 m,0.525 s,27.446°,and 1.092 m/s,compared to 0.314 m,0.888 s,27.698°,and 1.315 m/s from buoy data,respectively.These results demonstrate the model’s effective retrieval of wave and wind parameters.Finally,the model,incorporating altimeter and scatterometer data,is evaluated against SAR/SWIM single and dual payload inversion methods across different wind speeds.This comparison highlights the model’s superior inversion accuracy over other methods.

Inverse reliability analysis and design for tunnel face stability considering soil spatial variability

The traditional deterministic analysis for tunnel face stability neglects the uncertainties of geotechnical parameters,while the simplified reliability analysis which models the potential uncertainties by means of random variables usually fails to account for soil spatial variability.To overcome these limitations,this study proposes an efficient framework for conducting reliability analysis and reliability-based design(RBD)of tunnel face stability in spatially variable soil strata.The three-dimensional(3D)rotational failure mechanism of the tunnel face is extended to account for the soil spatial variability,and a probabilistic framework is established by coupling the extended mechanism with the improved Hasofer-Lind-Rackwits-Fiessler recursive algorithm(iHLRF)as well as its inverse analysis formulation.The proposed framework allows for rapid and precise reliability analysis and RBD of tunnel face stability.To demonstrate the feasibility and efficacy of the proposed framework,an illustrative case of tunnelling in frictional soils is presented,where the soil's cohesion and friction angle are modelled as two anisotropic cross-correlated lognormal random fields.The results show that the proposed method can accurately estimate the failure probability(or reliability index)regarding the tunnel face stability and can efficiently determine the required supporting pressure for a target reliability index with soil spatial variability being taken into account.Furthermore,this study reveals the impact of various factors on the support pressure,including coefficient of variation,cross-correlation between cohesion and friction angle,as well as autocorrelation distance of spatially variable soil strata.The results also demonstrate the feasibility of using the forward and/or inverse first-order reliability method(FORM)in high-dimensional stochastic problems.It is hoped that this study may provide a practical and reliable framework for determining the stability of tunnels in complex soil strata.

Inverse Method of Centrifugal Pump Impeller Based on Proper Orthogonal Decomposition (POD) Method

To improve the accuracy and reduce the calcu- lation cost for the inverse problem of centrifugal pump impeller, the new inverse method based on proper orthog- onal decomposition （POD） is proposed. The pump blade shape is parameterized by quartic Bezier curve, and the initial snapshots is generated by introducing the perturbation of the blade shape control parameters. The internal flow field and its hydraulic performance is predicted by CFD method. The snapshots vector includes the blade shape parameter and the distribution of blade load. The POD basis for the snap- shots set are deduced by proper orthogonal decomposition. The sample vector set is expressed in terms of the linear combination of the orthogonal basis. The objective blade shape corresponding to the objective distribution of blade load is obtained by least square fit. The Iterative correction algorithm for the centrifugal pump blade inverse method based on POD is proposed. The objective blade load dis- tributions are corrected according to the difference of the CFD result and the POD result. The two dimensional and three dimensional blade calculation cases show that the proposed centrifugal pump blade inverse method based on POD have good convergence and high accuracy, and thecalculation cost is greatly reduced. After two iterations, the deviation of the blade load and the pump hydraulic perfor- mance are limited within 4.0% and 6.0% individually for most of the flow rate range. This paper provides a promising inverse method for centrifugal pump impeller, which will benefit the hydraulic optimization of centrifugal pump.

Application of inverse method to estimation of boundary conditions during investment casting simulation

Inverse method was used in single crystal superalloy DD6 processing simulation during solidification. Numerical modeling coupled with experiments has been used to estimate the interface heat transfer coefficient （IHTC） between the surface of slab casting and inner mold. Calculated temperature dependent values of IHTC were obtained from a numerical solution. The calculated temperatures agreed well with the measurement of cooling profile.

Calculation of circulation in the South China Sea during summer of 2000 by the modified inverse method

On the basis of hydrographic data obtained in August 2000 cruise, the circulation in the South China Sea (SCS) is computed by the modified inverse method in combination with SSH data from TOPEX/ERS-2 analysis. For study of the dynamical mechanism, which causes the pattern of summer circulation in the SCS, the diagnostic model (Yuan et al. 1982. Acta Oceanologica Sinica,4(1):1-11; Yuan and Su. 1992. Numerical Computation of Physical Oceanography.474-542) is used to simulate numerically the summer circulation in the SCS. The following results have been obtained. (1) The central and southwestern SCSs are dominated mainly by anticy-clonic circulation systems. They are mainly as follows. 1) There is strong anticyclonic eddy southeast of Vietnam (W1). Its horizontal scale is about 300 km, and it extends vertically from the surface to the about 1 000 m level. 2) There are a warm eddy W2 southeast of Zhongsha Islands and the anticyclonic circulation system W3 west off the Luzon Island. 3) There is a stronger cyclonic eddy C1 between the anticyclonic eddies W1 and W2.4) A strong northward coastal jet is present near the coast of Vietnam, and separates from the coast of Vietnam at about 12° N to the northeast.(2)The northern SCS is dominated mainly by a cyclonic circulation system. There is a cyclonic circulation system near and north of Section N2. (3) The southeastern SCS is dominated mainly by the cyclonic circulation system. (4) Comparing the results of circulation in the SCS during the summer of 2000 with those during the summer of 1998, it is found that they agree qualitatively, but there is the some difference between them in quantity.This shows that the circulation in the SCS has obviously seasonal feature. (5) The dynamical mechanism which products the basic pattern of summer circulation is because the following two reasons: 1) the joint effect of the baroclinity and relief (JEBAR) is essential dynamical cause; and 2) it is next important dynamical cause that the interaction between the wind stress and bottom topography under the southerly monsoon. (6) Comparing the hydrographic structure and distribution of stream functions with the SSH data from TOPEX/ERS-2 analysis in the SCS during August of 2000, they agree qualitatively.

Modeling of Diffusion Transport through Oral Biofilms with the Inverse Problem Method

Aim The purpose of this study was to develop a mathe-matical model to quantitatively describe the passive trans-port of macromolecules within dental biofilms. Methodology Fluorescently labeled dextrans with different molecular mass （3 kD,10 kD,40 kD,70 kD,2 000 kD） were used as a series of diffusion probes. Streptococcus mutans,Streptococcus sanguinis,Actinomyces naeslundii and Fusobacterium nucleatum were used as inocula for biofilm formation. The diffusion processes of different probes through the in vitro biofilm were recorded with a confocal laser microscope. Results Mathematical function of biofilm penetration was constructed on the basis of the inverse problem method. Based on this function,not only the relationship between average concentration of steady-state and molecule weights can be analyzed,but also that between penetrative time and molecule weights. Conclusion This can be used to predict the effective concentration and the penetrative time of anti-biofilm medicines that can diffuse through oral biofilm. Further-more,an improved model for large molecule is proposed by considering the exchange time at the upper boundary of the dental biofilm.

Inverse Construction Methods of Heterogeneous NURBS Object Based on Additive Manufacturing

According to the requirement of heterogeneous object modeling in additive manufacturing(AM),the Non-Uniform Rational B-Spline(NURBS)method has been applied to the digital representation of heterogeneous object in this paper.By putting forward the NURBS material data structure and establishing heterogeneous NURBS object model,the accurate mathematical unified representation of analytical and free heterogeneous objects have been realized.With the inverse modeling of heterogeneous NURBS objects,the geometry and material distribution can be better designed to meet the actual needs.Radical Basis Function(RBF)method based on global surface reconstruction and the tensor product surface interpolation method are combined to RBF-NURBS inverse construction method.The geometric and/or material information of regular mesh points is obtained by RBF interpolation of scattered data,and the heterogeneous NURBS surface or object model is obtained by tensor product interpolation.The examples have shown that the heterogeneous objects fitting to scattered data points can be generated effectively by the inverse construction methods in this paper and 3D CAD models for additive manufacturing can be provided.

Nonlinear system compound inverse control method

A compound neural network is utilized to identify the dynamic nonlinear system. This network is composed of two parts： one is a linear neural network, and the other is a recurrent neural network. Based on the inverse theory a compound inverse control method is proposed. The controller has also two parts： a linear controller and a nonlinear neural network controller. The stability condition of the closed-loop neural network-based compound inverse control system is demonstrated .based on the Lyapunov theory. Simulation studies have shown that this scheme is simple and has good control accuracy and robustness.

Model predictive inverse method for recovering boundary conditions of two-dimensional ablation

A model predictive inverse method (MPIM) is presented to estimate the time- and space-dependent heat flux onthe ablated boundary and the ablation velocity of the two-dimensional ablation system. For the method, first of all, therelationship between the heat flux and the temperatures of the measurement points inside the ablation material is establishedby the predictive model based on an influence relationship matrix. Meanwhile, the estimation task is formulated as aninverse heat transfer problem (IHTP) with consideration of ablation, which is described by an objective function of thetemperatures at the measurement point. Then, the rolling optimization is used to solve the IHTP to online estimate theunknown heat flux on the ablated boundary. Furthermore, the movement law of the ablated boundary is reconstructedaccording to the estimation of the boundary heat flux. The effects of the temperature measurement errors, the numberof future time steps, and the arrangement of the measurement points on the estimation results are analyzed in numericalexperiments. On the basis of the numerical results, the effectiveness of the presented method is clarified.

Estimation of vertical diffusion coefficient based on a onedimensional temperature diffusion equation with an inverse method

Diapycnal mixing is important in oceanic circulation. An inverse method in which a semi-explicit scheme is applied to discretize the one-dimensional temperature diffusion equation is established to estimate the vertical temperature diffusion coefficient based on the observed temperature profiles. The sensitivity of the inverse model in the idealized and actual conditions is tested in detail. It can be found that this inverse model has high feasibility under multiple situations ensuring the stability of the inverse model, and can be considered as an efficient way to estimate the temperature diffusion coefficient in the weak current regions of the ocean. Here, the hydrographic profiles from Argo floats are used to estimate the temporal and spatial distribution of the vertical mixing in the north central Pacific based on this inverse method. It is further found that the vertical mixing in the upper ocean displays a distinct seasonal variation with the amplitude decreasing with depth, and the vertical mixing over rough topography is stronger than that over smooth topography It is suggested that the high-resolution profiles from Argo floats and a more reasonable design of the inverse scheme will serve to understand mixing processes.

Sensitivity and inverse analysis methods for parameter intervals

This paper proposes a sensitivity analysis method for engineering parameters using interval analyses.This method substantially extends the application of interval analysis method.In this scheme,parameter intervals and decision-making target intervals are determined using the interval analysis method.As an example,an inverse analysis method for uncertainty is presented.The intervals of unknown parameters can be obtained by sampling measured data.Even for limited measured data,robust results can also be obtained with the inverse analysis method,which can be intuitively evaluated by the uncertainty expressed in terms of an interval.For complex nonlinear problems,an iteratively optimized inverse analysis model is proposed.In a given set of loose parameter intervals,all the unknown parameter intervals that satisfy the measured information can be obtained by an iteratively optimized inverse analysis model.The influences of measured precisions and the number of parameters on the results of the inverse analysis are evaluated.Finally,the uniqueness of the interval inverse analysis method is discussed.

Using Inversed Augerhole Method to Determine the Hydraulic Conductivity of Soil

A kind of international rapid field measurement methods of hydraulic conductivity and it's applications in Sanjiang Plain have been introduced in the paper.

Efficient Calculation of the Radar Cross Section at the Interior Resonance by the Inverse Power Method

It is well known that the incorrect results will be given using either the electric or magnetic field integral equation to calculate the radar cross section (RCS) of a closed body at the interior resonance. In this paper, an effective iterative technique is used to correct the calculated surface current density from the electric field integral equation. The radar cross section is computed for an infinite conducting circular cylinder at the interior resonance, and the obtained results are in good agreement with the analytical results. The backscattering cross section of an infinite triangular cylinder in the vicinity of a resonant frequency is also calculated. It is shown that the presence method is efficient and accurate.

A new method--the inverse strain method(ISM)for preventing welding hot cracking of high strength aluminium alloy LY12CZ

In this paper a new method for preventing welding hot cracking—the inverse strain method(ISM)is developed on the principle of welding mechan- ics.Effectiveness and feasiblity of method in preventing welding hot cracking of high strength aluminum alloy LY12CZ by synchronous rolling during welding (SRDW)along both sides of the weld at a suitable distance behind the welding arc are examined.Experimental resulte indicate that welding hot cracking of LY12CY can be effectively prevented and the mechanical properties of welded joint can also be improved by the method.It is an important new solution for preventing hot cracking in welding of sheet metal.

Inverse scattering method and soliton solution family for the Einstein-Maxwell theory with multiple Abelian gauge fields

A Hauser-Ernst-type extended hyperbolic complex linear system given in our previous paper [Gao Y J 2004 Chin. Phys. 13 602] is slightly modified and used to develop a new inverse scattering method for the stationary axisymmetric Einstein-Maxwell theory with multiple Abelian gauge fields. The reduction procedures in this inverse scattering method are found to be fairly simple, which makes the inverse scattering method be fine and effective in practical application. As an example, a concrete family of soliton solutions for the considered theory is obtained.

Undersea Buried Pipeline Reconstruction Based on the Level Set and Inverse Multiquadric Regularization Method

The electric inversion technique reconstructs the subsurface medium distribution from acquired data.On the basis of electric inversion,objects buried under the earth or seabed,such as pipelines and unexploded ordnance,are detected and located in a contactless manner.However,the process of accurately reconstructing the shape of the target object is challenging because electric inversion is a nonlinear and ill-posed problem.In this work,we present an inverse multiquadric(IMQ)regularization method based on the level set function for reconstructing buried pipelines.In the case of locating underwater objects,the unknown inversion area is split into two parts,the background and the pipeline with known conductivity.The geometry of the pipeline is represented based on the level set function for achieving a noiseless inversion image.To obtain a binary image,the IMQ is used as the regularization term,which‘pushes’the level set function away from 0.We also provide an appropriate method to select the bandwidth and regularization parameters for the IMQ regularization term,resulting in reconstructed images with sharp edges.The simulation results and analysis show that the proposed method performs better than classical inversion methods.

Shape Sensing of Thin Shell Structure Based on Inverse Finite Element Method

Shape sensing as a crucial component of structural health monitoring plays a vital role in real-time actuation and control of smart structures,and monitoring of structural integrity.As a model-based method,the inverse finite element method(iFEM)has been proved to be a valuable shape sensing tool that is suitable for complex structures.In this paper,we propose a novel approach for the shape sensing of thin shell structures with iFEM.Considering the structural form and stress characteristics of thin-walled structure,the error function consists of membrane and bending section strains only which is consistent with the Kirchhoff–Love shell theory.For numerical implementation,a new four-node quadrilateral inverse-shell element,iDKQ4,is developed by utilizing the kinematics of the classical shell theory.This new element includes hierarchical drilling rotation degrees-of-freedom(DOF)which enhance applicability to complex structures.Firstly,the reconstruction performance is examined numerically using a cantilever plate model.Following the validation cases,the applicability of the iDKQ4 element to more complex structures is demonstrated by the analysis of a thin wallpanel.Finally,the deformation of a typical aerospace thin-wall structure(the composite tank)is reconstructed with sparse strain data with the help of iDKQ4 element.

GENERALIZED INVERSE RATIONAL EXTRAPOLATION METHODS FOR MATRIX SEQUENCES

Assume that a convergent matrix sequence{An}:An→A（n→∞）, An,A∈C3×3.We want to form a new matrix sequence {Hn}, derived from {An}, which has also A aslimit and whose convergence is faster than the of {An}. Three rational extrapolation meth-ods for accelerating the convergence of matrix sequences {An} are presented in this paper.The underlying methods are based on the generalized inverse for matrices which is

INVERSE POWER METHOD AND WEIGHTED SOBOLEV SPACES

1. Introduction This paper is a continuation of the paper [5]. Now we want to treat the problem