An X-band inverse class-F power amplifier is realized by a 1-mm Al Ga N/Ga N high electron mobility transistor（HEMT）.The intrinsic and parasitic components inside the transistor,especially output capacitor Cds,influ...An X-band inverse class-F power amplifier is realized by a 1-mm Al Ga N/Ga N high electron mobility transistor（HEMT）.The intrinsic and parasitic components inside the transistor,especially output capacitor Cds,influence the harmonic impedance heavily at the X-band,so compensation design is used for meeting the harmonic condition of inverse class-F on the current source plane.Experiment results show that,in the continuous-wave mode,the power amplifier achieves 61.7% power added efficiency（PAE）,which is 16.3% higher than the class-AB power amplifier realized by the same kind of HEMT.To the best of our knowledge,this is the first inverse class-F Ga N internally-matched power amplifier,and the PAE is quite high at the X-band.展开更多
A fully integrated class-E power amplifier（PA） at 2.4 GHz implemented in a 0. 18 μm 6-metal-layer mixed/RF CMOS （ complementary metal-oxide-semiconductor transistor ） technology is presented. A two-stage amplific...A fully integrated class-E power amplifier（PA） at 2.4 GHz implemented in a 0. 18 μm 6-metal-layer mixed/RF CMOS （ complementary metal-oxide-semiconductor transistor ） technology is presented. A two-stage amplification structure is chosen for this PA. The driving stage produces a high swing switch signal by using resonation technology. The output stage is designed as a class-E topology to realize the power amplification. Under a 1.2 V power supply, the PA delivers a maximum output power of 8. 8 dBm with a power-added efficiency （PAE） of 44%. A new power control method for the class-E power amplifier is described. By changing the amplitude and duty cycle of the signal which enters the class-E switch transistor, the output power can be covered from - 3 to 8. 8 dBm through a three-bit control word. The proposed PA can be used in low power applications, such as wireless sensor networks and biotelemetry systems.展开更多
This paper presents a 1.8 GHz class-E controlled power amplifier (PA). The proposed power amplifier is designed with two-stage architecture. The main advantage of the proposed technique for output control power is a h...This paper presents a 1.8 GHz class-E controlled power amplifier (PA). The proposed power amplifier is designed with two-stage architecture. The main advantage of the proposed technique for output control power is a high 37 dB output power dynamic range with good average power adding efficiency. The measurement results show that the PA achieves a high power gain of 23 dBm and power added efficiency (PAE) by 38%. The circuit was post layout simulated in a standard 0.18 μm CMOS technology.展开更多
This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency （RF） power amplifiers （PAs） as well as the use of these technologies in mobile broadb...This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency （RF） power amplifiers （PAs） as well as the use of these technologies in mobile broadband wireless communications. Four important aspects of PA design are addressed in this paper. First, we look at class-E PA design equations and provide an example of a class-E PA that achieves efficiency of 65-70% at 2.4 GHz. Then, we discuss state-of-the-art envelope tracking （ET） design for monolithic wideband RF mobile transmitter applications. A brief overview of Doherty PA design for the next-generation wireless handset applications is then given. Towards the end of the paper, we discuss an inherently broadband and highly efficient class-J PA design targeting future multi-band multi-standard wireless communication protocols.展开更多
The efficiency of inductive power links driven by Class-E amplifiers may deteriorate due to variation in the coupling coefficient when the relative position of the radio frequency (RF) coils changes.To solve this prob...The efficiency of inductive power links driven by Class-E amplifiers may deteriorate due to variation in the coupling coefficient when the relative position of the radio frequency (RF) coils changes.To solve this problem,a new design methodology of power links is presented in this paper.The aim of the new design is to use the feedback signal,which is a phase difference between the driving signal and the output current of the Class-E amplifier,to adjust the duty cycle and angular frequency of the driving signal to maintain the optimum state of the inductive power link,and to adjust the supply voltage to keep the output power constant when the coupling coefficient of the RF coils changes.The parameter adjustments with respect to the coupling coefficient and the feedback signal are derived from the design equation of the inductive power link.To validate the feedback control rules,a prototype of the inductive power link was constructed,and its performance validated with the coupling coefficient set at 0.2 and a duty cycle of 0.5.The experimental results showed that,by adjusting the duty cycle,the angular frequency,and the supply voltage,the power link can be kept in optimal operation with a constant output power when the coupling coefficient changes from 0.2 to 0.1 to 0.25.展开更多
A high efficiency class-1 linear audio power amplifier （PA） with an adaptive supply is presented. Its efficiency is improved by a dynamic supply to reduce the power transistors＇ voltage drop. A gain compression tec...A high efficiency class-1 linear audio power amplifier （PA） with an adaptive supply is presented. Its efficiency is improved by a dynamic supply to reduce the power transistors＇ voltage drop. A gain compression technique is adopted to make the amplifier accommodate a single positive supply. Circuit complicity and chip area are reduced because no charge pump is necessary for the negative supply. A common shared mode voltage and a symmetric layout pattern are used to minimize the non-linearity. A peak efficiency of 80% is reached at peak output power. The measured THD＋N before and after the supply switching point are 0.01% and 0.05%, respectively. The maximum output power is 410 mW for an 8 f2 speaker load. Unlike switching amplifiers, the class-I amplifier operates as a linear amplifier and hence has a low EMI. The advantage of a high efficiency and low EMI makes the class-1 amplifier suitable for portable and RF sensitive applications.展开更多
为了满足移动通信系统中功率放大器宽频带和高效率的需求,采用阶梯阻抗网络实现宽带匹配电路,设计了一款高效率连续逆F类功率放大器。选用CGH40010F GaN HEMT晶体管,通过对连续逆F类功率放大器的理论分析,并且结合ADS负载牵引与源牵引仿...为了满足移动通信系统中功率放大器宽频带和高效率的需求,采用阶梯阻抗网络实现宽带匹配电路,设计了一款高效率连续逆F类功率放大器。选用CGH40010F GaN HEMT晶体管,通过对连续逆F类功率放大器的理论分析,并且结合ADS负载牵引与源牵引仿真,提取各频点的最佳负载阻抗和源阻抗,设计阶梯阻抗匹配电路,最终实现了一款宽带高效率功率放大器。测试结果表明,该功率放大器在3.2~3.8 GHz频段内,增益大于14 dB,增益平坦度小于±0.4 dB,饱和输出功率为40.6~40.9 dBm,最大漏极效率为64%~68%。该功率放大器的测试性能良好,可以为宽频带高效率功率放大器的设计提供参考。展开更多
传统的F类和逆F类功率放大器的带宽不宽,且对于功放输出信号的谐波控制比较严格。在连续类功放理论的基础上,设计了一款在工作带宽内连续F类和连续逆F类模式转换的功率放大器。设计的功放采用了Cree公司的CGH40010F GaN HEMT晶体管。通...传统的F类和逆F类功率放大器的带宽不宽,且对于功放输出信号的谐波控制比较严格。在连续类功放理论的基础上,设计了一款在工作带宽内连续F类和连续逆F类模式转换的功率放大器。设计的功放采用了Cree公司的CGH40010F GaN HEMT晶体管。通过调整功放管输出端的谐波控制网络,控制谐波阻抗在Smith圆图中位置分布,从而在带宽内同时实现连续F类和连续逆F类的工作模式。制作了测试板,结果表明在2.4～4.2 GHz的带宽内,增益在11 dB以上,漏极效率为55%～82%,输出功率在39.5～41.9 dBm。采用了10 MHz的LTE单载波信号进行功放的数字预失真测试,功放的输出ACPR改善了6 dB以上。展开更多
基金Project supported by the National High Technology Research and Development Program of China(Grant No.2015AA016801)
文摘An X-band inverse class-F power amplifier is realized by a 1-mm Al Ga N/Ga N high electron mobility transistor（HEMT）.The intrinsic and parasitic components inside the transistor,especially output capacitor Cds,influence the harmonic impedance heavily at the X-band,so compensation design is used for meeting the harmonic condition of inverse class-F on the current source plane.Experiment results show that,in the continuous-wave mode,the power amplifier achieves 61.7% power added efficiency（PAE）,which is 16.3% higher than the class-AB power amplifier realized by the same kind of HEMT.To the best of our knowledge,this is the first inverse class-F Ga N internally-matched power amplifier,and the PAE is quite high at the X-band.
基金The National High Technology Research and Development Program of China(863 Program)(No.2007AA01Z2A7)
文摘A fully integrated class-E power amplifier（PA） at 2.4 GHz implemented in a 0. 18 μm 6-metal-layer mixed/RF CMOS （ complementary metal-oxide-semiconductor transistor ） technology is presented. A two-stage amplification structure is chosen for this PA. The driving stage produces a high swing switch signal by using resonation technology. The output stage is designed as a class-E topology to realize the power amplification. Under a 1.2 V power supply, the PA delivers a maximum output power of 8. 8 dBm with a power-added efficiency （PAE） of 44%. A new power control method for the class-E power amplifier is described. By changing the amplitude and duty cycle of the signal which enters the class-E switch transistor, the output power can be covered from - 3 to 8. 8 dBm through a three-bit control word. The proposed PA can be used in low power applications, such as wireless sensor networks and biotelemetry systems.
文摘This paper presents a 1.8 GHz class-E controlled power amplifier (PA). The proposed power amplifier is designed with two-stage architecture. The main advantage of the proposed technique for output control power is a high 37 dB output power dynamic range with good average power adding efficiency. The measurement results show that the PA achieves a high power gain of 23 dBm and power added efficiency (PAE) by 38%. The circuit was post layout simulated in a standard 0.18 μm CMOS technology.
文摘This paper presents a brief overview of several promising design technologies for high efficiency silicon-based radio frequency （RF） power amplifiers （PAs） as well as the use of these technologies in mobile broadband wireless communications. Four important aspects of PA design are addressed in this paper. First, we look at class-E PA design equations and provide an example of a class-E PA that achieves efficiency of 65-70% at 2.4 GHz. Then, we discuss state-of-the-art envelope tracking （ET） design for monolithic wideband RF mobile transmitter applications. A brief overview of Doherty PA design for the next-generation wireless handset applications is then given. Towards the end of the paper, we discuss an inherently broadband and highly efficient class-J PA design targeting future multi-band multi-standard wireless communication protocols.
基金Project (No.60271031) supported by the National Natural Science Foundation of China
文摘The efficiency of inductive power links driven by Class-E amplifiers may deteriorate due to variation in the coupling coefficient when the relative position of the radio frequency (RF) coils changes.To solve this problem,a new design methodology of power links is presented in this paper.The aim of the new design is to use the feedback signal,which is a phase difference between the driving signal and the output current of the Class-E amplifier,to adjust the duty cycle and angular frequency of the driving signal to maintain the optimum state of the inductive power link,and to adjust the supply voltage to keep the output power constant when the coupling coefficient of the RF coils changes.The parameter adjustments with respect to the coupling coefficient and the feedback signal are derived from the design equation of the inductive power link.To validate the feedback control rules,a prototype of the inductive power link was constructed,and its performance validated with the coupling coefficient set at 0.2 and a duty cycle of 0.5.The experimental results showed that,by adjusting the duty cycle,the angular frequency,and the supply voltage,the power link can be kept in optimal operation with a constant output power when the coupling coefficient changes from 0.2 to 0.1 to 0.25.
基金supported by the Analog Devices and ASIC Laboratory,China
文摘A high efficiency class-1 linear audio power amplifier （PA） with an adaptive supply is presented. Its efficiency is improved by a dynamic supply to reduce the power transistors＇ voltage drop. A gain compression technique is adopted to make the amplifier accommodate a single positive supply. Circuit complicity and chip area are reduced because no charge pump is necessary for the negative supply. A common shared mode voltage and a symmetric layout pattern are used to minimize the non-linearity. A peak efficiency of 80% is reached at peak output power. The measured THD＋N before and after the supply switching point are 0.01% and 0.05%, respectively. The maximum output power is 410 mW for an 8 f2 speaker load. Unlike switching amplifiers, the class-I amplifier operates as a linear amplifier and hence has a low EMI. The advantage of a high efficiency and low EMI makes the class-1 amplifier suitable for portable and RF sensitive applications.
