Inhibition characteristics of circulating current in parallel inverter driving system of mine hoist

This research investigated the outputting circulation current inhibition characteristic which are controlled by the instantaneous feedback voltage in inverter parallel driving of the mine hoist. We established a transfer function of the parallel inverters controlled by the close-loop adjustment of instantaneous voltage feedback. The influence of the parameters of the close-loop feedback circuit to the inhibition effects to the outputting circulation current is observed. After analyzing the circulating current inhibition characteristics, the proportion integration （PI） controller is introduced into the close-loop adjustment by instantaneous voltage feedback. The characteristics equation is gained to determine the PI parameters by drawing the Bode plots. The inhibition effects of the proposed controller are examined by the established simulation model of parallel inverter system. The harmonic distortion rate at the outputting voltage frequency value of 4, 10, 20, 41 and 50 Hz, are all lower than 2.32 % by the instantaneous outputting voltage feedback.

Starting Characteristics of Motor in Inverter-Motor Drive System

When the induction motor is fed from the PWM VSI inverter, with and without torque enhancing function, the variations of the starting torque and the starting current versus the starting frequency are analyzed, based on the steady state equivalent circuit of the induction motor.The corresponding expressions are derived, and the corresponding curves are also drawn, from which the initial starting frequency range can be determined properly and easily. The initial starting frequency range is the common range, in which the starting torque should be high enough and the starting current low enough.Some other useful formulas are also derived.These results are significant for electrical drive designers to make the starting schemes. The effects of the increase of the stator and the rotor resistances on the starting torque and the initial starting frequency range are also discussed, which is caused by the skin effects of the high order harmonics present in the PWM inverter output voltage.

Characteristics of permanent magnet linear synchronous motor fed by spwm inverter based on field-circuit coupled method

Presented field-circuit coupled adaptive time-stepping finite element method to study on permanent magnet linear synchronous motor (PMLSM) characteristics fed by SPWM voltage source inverter.In air-gap field where the direction or magnitude of the field is changing rapidly,the smallest elements are demanded due to high accuracy to use adaptive meshing technique.The co-simulation was used with the status space functions and time-step finite element functions,in which time-step of the status space functions was the smallest than finite element functions'.The magnitude relation of the normal elec- tromagnetic force and tangential electromagnetic force and the period were attained,and current curve was very abrupt at current zero area due to the bigger resistance and leak- age reactance,including main characteristics of motor voltage and velocity.The simulation results compare triumphantly with the experiments results.

Dark output characteristic of γ-ray irradiated CMOS digital image sensors

The quality of dark output images from the CMOS (complementarymetal oxide semiconductor) black and white (B & W) digital imagesensors captured before and after γ-ray irradiation was studied. Thecharacteristic parameters of the dark output images captured atdifferent radiation dose, e.g. average brightness and itsnon-uniformity of dark out- put images, were analyzed by our testsoftware. The primary explanation for the change of the parameterswith the radi- ation dose was given.

Reducing the minimum output power of soft-switching inverter arc welding power supplies

The full-bridge zero-voltage and zero-current switching inverter, which can adjust the output power by keeping the duty-cycle of lagging arm constant, changing the duty-cycle of leading arm, is a common circuit topology of soft-switching inverter arc welding power supplies. However, the output power still remains a certain value when the duty-cycle of leading arm decreases to zero. The working-mode of soft-switching inverter and the waveforms of major parameters with the condition of duty-cycle of leading arm being zero are studied in this paper. U-1 characteristic experiments prove that the minimum output power of soft-switching circuit, which depends on the charged voltage of capacitors in parallel with leading arm, can be decreased by reducing the duty-cycle of lagging arm. By switching working-modes between half-bridge and full-bridge, the output power can swing from zero to the power rating.

Micro-source Inverters With Capacitive Equivalent Output Impedance for Improving Micro-grid Voltages

将分布式电源逆变器等效输出阻抗设计成容性可使其体现对系统无功电压调整过程相逆的电源特性,这种特性使得分布式电源逆变器更容易参与公共连接点处的电压调整。对比等效输出阻抗成感性、阻性和容性的3类逆变器下垂控制特性,对容性等效输出阻抗逆变器电压电流控制环进行数学建模;针对容性等效输出阻抗逆变器设计具备下垂调节和克服电压偏离功能的鲁棒功率外环控制器。对比仿真和实验证明,容性输出阻抗分布式电源逆变器控制器能够快速抑制系统功率变化带来的电压波动,能有效地参与系统电压调整。

Difference in electron-and gamma-irradiation effects on output characteristic of color CMOS digital image sensors

Changes of the average brightness and non-uniformity of dark output images,and quality of pictures captured under natural lighting for the color CMOS digital image sensorsirradiated at different electron doses have been studied in comparison to those from theγ-irradiated sensors. For the electron-irradiated sensors, the non-uniformity increases obviouslyand a small bright region on the dark image appears at the dose of 0.4 kGy. The average brightnessincreases at 0.4 kGy, increases sharply at 0.5 kGy. The picture is very blurry only at 0.6 kGy,showing the sensor undergoes severe performance degradation. Electron radiation damage is much moresevere than γ radiation damage for the CMOS image sensors. A possible explanation is presented inthis paper.

Controlling the output power of soft switching arc welding inverter by two-stage continuous PWM method

The full bridge zero voltage zero current switching （ FB-ZVZCS ） , which could adjust the output power by keeping the duty ratio of lagging leg constant and changing the duty ratio of leading leg, was a common circuit of soft switching arc welding inverter power source. However, when the duty ratio of leading leg was reduced to zero, the output power stayed the constant value instead of becoming zero. The working status and waveforms of some major parameters were studied in this paper while the duty ratio of leading leg was zero. It was concluded that the minimum output power of soft switching inverter was related to the charging voltage of paraUel capacitors, and the output power also could be reduced by reducing the duty ratio of lagging leg. A novel two-stage continuous PWM control method that could switch working-mode between full bridge and half bridge was put forward in this paper. This kind of control method could further reduce the output power of soft switching inverter in order to meet the requirement of low heat input of sheet metal welding.

Exploration discovery and hydrocarbon accumulation characteristics of the Doseo strike-slip and inverted basin, Chad

Several international oil companies had conducted petroleum exploration, but failed to make any commercially viable discoveries in the Doseo Basin for over 30 years. In this article, an integrated analysis, based on the latest seismic and drilling data combined with exploration practice and tectonic, sedimentary as well as petroleum-geological characteristics of the basin, has been conducted with the aim to disclose the key factors of hydrocarbon accumulation and enrichment and then to find the potential petroleum plays. The Doseo Basin in Chad is a Meso-Cenozoic lacustrine rift basin developed on the Precambrian crystalline basement in the Central African Shear Zone. It is a half graben rift controlled by the strike-slip fault at the northern boundary, and can be divided into two sub-basins, an uplift and a slope. The basin experienced two rifting periods in the Cretaceous and was strongly inverted with the erosion thickness of 800–1000 m during the Eocene, and then entered the depression and extinction period. Structurally, a large number of normal faults and strike-slip faults are identified in the basin, and the boundary faults are inverted faults with normal at first. The main structural styles include inverted anticlines, fault noses, complex fault-blocks and flower structures. The Lower Cretaceous is the main sedimentary strata, which are divided into the Mangara Group, Kedeni, Doba and Koumra Formations from bottom to up. Two transgressive-regressive cycles developed in the Lower Cretaceous indicates with mainly lacustrine, fluvial, delta, braided-delta, fan-delta sandstone and mudstone. The effective source rock in the basin is the deep-lacustrine mudstone of the Lower Cretaceous containing the type Ⅰ and type Ⅱ;organic matters. Furthermore, Inverted anticlines and fault-complicated blocks comprise the main trap types and the Kedeni Uplift is the most favorable play, followed by the Northern Steep Slope and Southern Gentle Slope. Lateral sealing capacity of faults controls the hydrocarbon abundance.

Structure design and characteristics analysis of a cylindrical giant magnetostrictive actuator for ball screw preload

In order to achieve automatic adjustment of the double-nut ball screw preload, a magnetostrictive ball screw preload system is proposed. A new cylindrical giant magnetostrictive actuator （CGMA）, which is the core component of the preload system, is developed using giant magnetostrictive material （GMM） with a hole. The pretightening force of the CGMA is determined by testing. And the magnetic circuit analysis method is introduced to calculate magnetic field intensity of the actuator with a ball screw shaft. To suppress the thermal effects on the magnetostrictive outputs, an oil cooling method which can directly cool the heat source is adopted. A CGMA test platform is established and the static and dynamic output characteristics are respectively studied. The experimental results indicate that the CGMA has good linearity and no double-frequency effect under the bias magnetic field and the output accuracy of the CGMA is significantly improved with cooling measures. Although the output decreased with screw shaft through the actuator, the performance of CGMA meets the design requirements for ball screw preload with output displacement more than 26 μm and force up to 6200 N. The development of a CGMA will provide a new approach for automatic adjustment of double-nut ball screw preload.

Realization of non HF air plasma cutting power source based on a complexisolated inverter

On the basis of analyzing and testing of common inverting circuits, a new type inverter, which has a special inverting circuit called complex isolated, has been put forward. In turn, an applicable air plasma cutting machine has also been put into use. Testing results show that this kind inverter has lots of properties as high reliability, high efficiency, good EMC(electromagnetic compatibility) and easy operating. The complex isolated inverting circuit can be considered as a quite valuable reference for the research of high power welding inverter.

Influence of fin architectures on linearity characteristics of AlGaN/GaNFinFETs

We investigate the influence of fin architecture on linearity characteristics of AlGaN/GaNFinFET.It is found that the Fin FET with scaled fin dimensions exhibits much flatter Gm characteristics than the one with long fins as well as planar HEMT.According to the comparative study,we provide direct proof that source resistance rather than tri-gate structure itself dominates the Gm behavior.Furthermore,power measurements show that the optimized FinFET is capable of delivering a much higher output power density along with significant improvement in linearity characteristics than conventional planar HEMT.This study also highlights the importance of fin design in GaN-based FinFET for microwave power application,especially high-linearity applications.

A neutral point potential drift control method for NPC three-level inverter

The output current harmonic distortion of a three-level inverter is less than the traditional twolevel inverter.The voltage stress of the semiconductor switch is low.A neutral point potential drift control method is proposed to solve the problem of the neutral point potential drift of the three-level inverter.The interaction mechanism between the neutral point potential and the space voltage vector is presented.The small vector output by the inverter is found to be the root cause of the midpoint potential drift.It is found that the fluctuation of the midpoint potential could be suppressed by increasing the capacitance value of the inverter bus voltage stabilizing capacitor.Furthermore,it inhibits the fluctuation of the midpoint potential.The experimental results verify the efficiency and precision of the proposed method.

Research on a New Control Strategy of Three Phase Inverter for Unbalanced Loads

One of the very important functions of three-phase inverter is to maintain the symmetric three-phase output voltage when the three-phase loads are unbalanced. Although the traditional symmetrical component decomposing and superimpose theory can keep the voltage balance through compensating the positive-, negative- and zero-sequence components of the output voltage of inverter, however, this method is time-consuming and not suitable for control. Aiming at high power medium frequency inverter source, a P+Resonant (Proportion and Resonant) controller which ensured a balanced three phase output voltage under unbalanced load is proposed in this paper. The regulator was proved to be applicable to both three-phase three-wire system and three-phase four-wire system and developed two methods of realization. The simulation results verified that this method can suppressed effectively the output voltage distorted caused by the unbalanced load and attained a high quality voltage waveforms.

基于数据驱动的分布式光伏发电功率预测方法研究进展

从综述的角度,以分布式光伏系统为对象,分析了功率预测技术的发展情况、存在的难点以及主要影响因素,梳理了应用数据驱动方法实现功率准确预测的技术路线。再以空间相关性、历史出力功率以及气象等影响因素为切入点,梳理了光伏系统数据驱动的功率预测研究现状,分析其相应的数据增强、时空图信息以及特征融合的手段,讨论了技术的优缺点。最后给出了功率预测数据驱动方法研究方向和发展建议。

基于皮肤-脂肪模型的太赫兹体内多输入多输出信道特性分析与建模

为探究太赫兹(THz)频段体内多输入多输出(MIMO)通信系统的传输特性,该文在0.8~1.2 THz下构建了精确的皮肤-脂肪模型,对皮肤-脂肪模型中垂直方向和水平方向的链路进行全波电磁仿真,分析太赫兹体内信道特性,建立路径损耗模型。首先,结合太赫兹频段人体组织的介电特性和人体皮肤的解剖学结构构建皮肤-脂肪模型。其次,对比分析了3条链路的路径损耗和阴影衰落,提出带有等效吸收因子的太赫兹体内路径损耗模型。最后,对3条链路的莱斯K因子、均方根时延扩展、MIMO容量进行分析。仿真分析表明,带有等效吸收因子的太赫兹体内路径损耗模型可以更准确地描述加长距离垂直链路2的路径损耗,发射端在体表可以增强MIMO容量。该文的工作可以为太赫兹体内通信系统的设计和优化提供参考。

正弦波逆变器波形稳定混合控制策略研究

受蓄电池放电能力和实际电压限制,逆变器在稳定运行状态下,若瞬间断开或连接大负载,会使负载电压出现较大波动,严重时损坏设备。若直流母线电压较低,则逆变器输出的正弦波波形易产生削顶削底现象,对感性负载有影响。针对该问题,提出有效值闭环控制与定点电压闭环控制相结合的混合控制策略,在电压高于320 V时,采用定点电压闭环控制方式;若直流母线电压低于320 V,采用有效值闭环控制方式。经过仿真分析和实验验证,采用该混合控制策略,逆变器能够快速响应负载变动并使正弦波波形不会产生畸形。

热声制冷机中磁致伸缩换能器设计及特性分析

本文针对传统驱动方式热声制冷机效率低的问题,提出一种用磁致伸缩换能器驱动热声制冷机的设计方案。磁致伸缩换能器作为热声制冷机的驱动器,其输出特性对热声制冷机制冷效果至关重要。基于此对磁致伸缩换能器开展了从超磁致伸缩材料几何参数、激励线圈最佳电磁转换效率和内部磁路3个方面的优化设计研究,最后对换能器输出特性进行了仿真分析。结果表明:在4.6 kHz时位移最大,输出位移达到63μm,满足驱动热声制冷机需求。

水风光储一体化系统中储能平抑出力波动效果评价研究

随着新型电力系统的发展,风能、光能等高比例新能源的联网运行是实现其大规模开发利用重要途径,也是在双碳政策背景下节能减排的重要方式。由于风电和光伏出力具有极强的随机性与不可控性,高比例的风电与光伏接入电网势必会产生巨大的波动,从而降低电能质量,给电网运行带来许多不便。如何既能高比例地消纳风电与光伏,又能尽量减少其并网产生的不利影响成为一项重要课题。本文建立了风电、光伏及水电的出力模型,分析了不同情景下的出力特点与趋势,根据其出力的强不确定性、间歇性与周期性的特点,计算不同组合方式下的组合能源系统出力数据并对比分析。以某水电站为例,建立以水电调节为主的水风光发电系统,并在其中加入超短期储能装置,研究发现此组合能源出力系统可以很好地平抑出力波动并达到出力最高,且经济效益良好。