Effects of ion-exchange on the pervaporation performance and microstructure of NaY zeolite membrane

Pervaporation performance of NaY zeolite membranes is improved by ion-exchange with di-valent nitrate salt.Different nitrate salts,including Co(NO_(3))_(2),Mg(NO_(3))_(2),Zn(NO_(3))_(2),Ca(NO_(3))_(2),Cu(NO_(3))_(2),KNO_(3),and AgNO_(3),have great effects on the channel structure and water affinity of the NaY zeolite membrane.When the concentration of nitrate salt,ion-exchange temperature and time are 0.1 mol·L^(-1),50℃and 2 h,the ion-exchange degree order of NaY zeolites is Ag^(+)>K^(+)>Ca^(2+)>Zn^(2+)>>Co^(2+)>Mg^(2+).Especially,Ag^(+)and K^(+)cation exchange degree of NaY zeolites are achieved to 96.54% and 82.77% in this work.BET surface,total pore capacity,pore size distribution and water contact angle of the ion-exchanged NaY zeolites are all disordered by mono-and di-valent cations.Di-valent nitrate salt is favor for increasing the dehydration performance of NaY zeolite membranes by ion-exchange.When the ion-exchange solution is Zn(NO_(3))_(2),the total flux variation and separation factor variation of the NaY membrane(M-5)are -45% and 230% for separation of 10%(mass)H_(2)O/EtOH mixture by pervaporation,and the ion-exchanged membranes showed good reproducibility.

Suppression of current-induced membrane discharge of bipolar membranes by regulating ion crossover transport

Bipolar membranes(BPMs)exhibit the unique capability to regulate the operating environment of electrochemical system through the water dissociation-combination processes.However,the industrial utilization of BPMs is limited by instability and serious energy consumption.The current-induced membrane discharge(CIMD)at high-current conditions has a negative influence on the performance of anion-exchange membranes,but the underlying ion transport mechanisms in the BPMs remain unclear.Here,the CIMD-coupled Poisson-Nernst-Planck(PNP)equations are used to explore the ion transport mechanisms in the BPMs for both reverse bias and forward bias at neutral and acid-base conditions.It is demonstrated that the CIMD effect in the reverse-bias mode can be suppressed by enhancing the diffusive transport of salt counter-ions(Na^(+)and Cl^(−))into the BPMs,and that in the forward-bias mode with acid-base electrolytes can be suppressed by matching the transport rate of water counter-ions(H_(3)O^(+)and OH^(−)).Suppressing the CIMD can promote the water dissociation in the reverse-bias mode,as well as overcome the plateau of limiting current density and reduce the interfacial blockage of salt co-ions(Cl^(−))in the anion-exchange layer in the forward-bias mode with acid-base electrolytes.Our work highlights the importance of regulating ion crossover transport on improving the performance of BPMs.

A RAPID METHOD TO DETERMINE DIFFUSION COEFFICIENTS OF COUNTER-IONS IN AN ION-EXCHANGE MEMBRANE

1 INTRODUCTIONRapid and precise methods to obtain the diffusion coefficients of counter-ions are im-portant for the characterization of ion exchange membranes.Many theoreticaldescriptions of ion transport in ion exchange membranes have been developed by usingthe principles of irreversible thermodynamics,or the Nernst-Planck equations.Fick’s law can also be used for the description of the transport of ions with equaldiffusivity.However,for counter-ions of different diffusivities,Nerst-Planck

Chitosan derived carbon membranes as protective layers on zinc anodes for aqueous zinc batteries

Aqueous zinc batteries with low cost and inherent safety are considered to be the most promising energy storage devices.However,they suffer from poor cycling stability and low coulombic efficiencies caused by the adverse zinc dendrites on the anodes during the discharging/charging processes.Chitosan is a kind of natural amino polysaccharide,which is rich in nitrogen and carbon.When sintered at high temperatures,carbon membranes have been achieved with excellent conductivity and graphitization degree,which could enhance the ability to induce zinc ion uniform deposition to some extent.In this work,a type of carbon membrane using chitosan as raw materials has been fabricated by sintering,and then assembled as the protect layers in aqueous zinc batteries.The results show that the samples could retain smoother surfaces when adopting the sintering temperature of 800℃,and the assembled batteries are able to achieve about 700 h at a current density of 0.25m A·cm^(-2),which is far longer than those of the similar batteries without any carbon membranes.

Polymer/Ceramic Composite Membranes and Their Application in Pervaporation Process

Pervaporation(PV),as an environmental friendly and energy-saving separation technology,has been received increasing attention in recent years.This article reviews the preparation and application of macroporous ceramic-supported polymer composite pervaporation membranes.The separation materials of polymer/ceramic composite membranes presented here include hydrophobic polydimethylsiloxane(PDMS) and hydrophilic poly(vinyl alcohol)(PVA),chitosan(CS) and polyelectrolytes.The effects of ceramic support treatment,polymer solution properties,interfacial adhesion and incorporating or blending modification on the membrane structure and PV performance are discussed.Two in-situ characterization methods developed for polymer/ceramic composite membranes are also covered in the discussion.The applications of these composite membranes in pervaporation process are summarized as well,which contain the bio-fuels recovery,gasoline desulfuration and PV coupled proc-ess using PDMS/ceramic composite membrane,and dehydration of alcohols and esters using ceramic-supported PVA or PVA-CS composite membrane.Finally,a brief conclusion remark on polymer/ceramic composite mem-branes is given and possible future research is outlined.

Membrane Crystallization for Process Intensification and Control:A Review

Crystallization is a fundamental separation technology used for the production of particulate solids.Accurate nucleation and growth process control are vitally important but difficult.A novel controlling technology that can simultaneously intensify the overall crystallization process remains a significant challenge.Membrane crystallization(MCr),which has progressed significantly in recent years,is a hybrid technology platform with great potential to address this goal.This review illustrates the basic concepts of MCr and its promising applications for crystallization control and process intensification,including a state-of-the-art review of key MCr-utilized membrane materials,process control mechanisms,and optimization strategies based on diverse hybrid membranes and crystallization processes.Finally,efforts to promote MCr technology to industrial use,unexplored issues,and open questions to be addressed are outlined.

Polyvinylamine-Based Facilitated Transport Membranes for Post-Combustion CO_(2) Capture:Challenges and Perspectives from Materials to Processes

Carbon dioxide(CO_(2))capture by gas-separation membranes has become increasingly attractive due to its high energy efficiency,relatively low cost,and environmental impact.Polyvinylamine(PVAm)-based facilitated transport(FT)membranes were developed in the last decade for CO_(2) capture.This work discusses the challenges of applying PVAm-based FT membranes from materials to processes for postcombustion CO_(2) capture in power plants and cement factories.Experiences learned from a pilot demonstration system can be used to guide the design of other membranes for CO_(2) capture.The importance of module and process design is emphasized in the achievement of a high-performance membrane system.Moreover,the results from process simulation and cost estimation indicate that a three-stage membrane system is feasible for achieving a high CO_(2) purity of 95 vol%.The specific CO_(2) capture cost was found to significantly depend on the required CO_(2) capture ratio,and a moderate CO_(2) capture ratio of 50%presented a cost of 63.7USD per tonne CO_(2) captured.Thus,FT membrane systems were found to be more competitive for partial CO_(2) capture.

Geometrical Reconstruction and CNC Process of Spurious Tympanic Membrane Based on Reverse Engineering

Perforation of tympanic membrane is one of the main reasons for both deafness and dyssaudia.We could improve and restore audition by restoring or replacing the tympanic membrane.So,whether you can make the spurious tympanic membrane successfully is one of the keys to a successful operation.Utilizing CMM (Coordinate Measuring Machine) measurement equipment, we measured tympanic membrane model precisely and digitally.We also analysed the measured data by point to surface and we have successfully reconstructed the CAD model of the spurious tympanic membrane.Using the model we have got,we schemed out the mold of spurious tympanic membrane.In addition,we utilized MasterCAM compiling CNC (Computerized Numerical Con- trol) code and simulating the course of working.Ultimately,we obtained the mold of spurious tympanic membrane.Our research in this article has great significance to the success of spurious tympanic membrane grafting operation.

Effects of Sn residue on the high temperature stability of the H_2-permeable palladium membranes prepared by electroless plating on Al_2O_3 substrate after SnCl_2–PdCl_2 process: A case study

The stability of composite palladium membranes is of key importance for their application in hydrogen energy systems. Most of these membranes are prepared by electroless plating, and beforehand the substrate surface is activated by a SnCl_2–PdCl_2 process, but this process leads to a residue of Sn, which has been reported to be harmful to the membrane stability. In this work, the Pd/Al_2O_3 membranes were prepared by electroless plating after the SnCl_2–PdCl_2 process. The amount of Sn residue was adjusted by the SnCl_2 concentration, activation times and additional Sn(OH)_2coating. The surface morphology, cross-sectional structure and elemental composition were analyzed by scanning electron microscopy(SEM), metallography and energy dispersive spectroscopy(EDS), respectively. Hydrogen permeation stability of the prepared palladium membranes were tested at450–600 °C for 400 h. It was found that the higher SnCl_2 concentration and activation times enlarged the Sn residue amount and led to a lower initial selectivity but a better membrane stability. Moreover, the additional Sn(OH)_2coating on the Al_2O_3 substrate surface also greatly improved the membrane selectivity and stability.Therefore, it can be concluded that the Sn residue from the SnCl_2–PdCl_2 process cannot be a main factor for the stability of the composite palladium membranes at high temperatures.

Pollutants removal and simulation model of combined membrane process for wastewater treatment and reuse in submarine cabin for long voyage

A laboratory scale test was conducted in a combined membrane process （CMP） with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage. Removal performance of chemical oxygen demand （COD）, ammonia nitrogen （NH4^＋-N）, turbidity and anionic surfactants （LAS） was investigated under different conditions. It was observed that the effluent COD, NH4^＋-N, turbidity and LAS flocculated in ranges of 0.19-0.85 mg/L, 0.03-0.18 mg/L, 0.0-0.15 NTU and 0.0-0.05 mg/L, respectively in spite of considerable fluctuation in corresponding influent of 2120-5350 mg/L, 79.5-129.3 mg/L, 110-181.1NTU and 4.9-5.4 mg/L. The effluent quality of the CMP could meet the requirements of mechanical water and hygiene water according to the class I water quality standards in China （GB3838-2002）. The removal rates of COD, NH4^＋-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradation is indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network （BPNN） theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4^＋-N was 5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The results indicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4^＋-N, turbidity and LAS. It also suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters in submarine.

Pilot study on treatment of low turbidity and low temperature water by coagulation-immersed membrane process

The objective of this paper was to investigate the practicability of coagulation-immersed membrane process during low-temperature period through the study of steady operation,chemical cleaning methods,water quality and agent consumption.Experimental results showed that:membrane performance decreases with the reduction of temperature,but low temperature has little effect on stable operation of immersed membrane when coagulation as pretreatment.EFM with 1200 mg/L sodium hypochlorite after every 48 filtration cycles was made for reducing membrane fouling efficiently,and the method,with 1.5% sodium hydroxide and 3500 mg/L sodium hypochlorite for 10 h and then 2% hydrochloric acid for 4 h,is an appropriate cleaning method under low temperature.Compared with convention treatment process,immersed membrane process not only has same agent consumption,but also permeated water quality is more superior such as fine removal effect on turbidity with average 0.10 NTU.Therefore,coagulation-immersed membrane process is more appropriate for increasing water quality demand and the treatment of low turbidity and low temperature water.

Growth process and short chain alcohol separation performance of fluoride-containing NaY zeolite membrane

Growth process of the NaY zeolite membranes was investigated by fluoride-containing precursor synthesis gel.Compared with the fluoride-free precursor synthesis gel,the irregular NaY zeolite crystals were dissolved into amorphous by the fluoride-containing precursor synthesis gel initially,the amorphous contained the Y-type zeolite characteristic bands by the IR characterization.The fine square NaY zeolite crystals arose from the amorphous,which were accumulated and gradually grew into a dense NaY zeolite layer on the support surface after 6.5 h.Because the excessive NaY zeolites were dissolved by the strong alkaline and fluoride-containing precursor synthesis gel,there was plenty of amorphous on NaY zeolites layer for prolonging the crystallization time.The assynthesized NaY zeolite membranes had a good separation performance and repeatability for separation of 10 wt%methanol(MeOH)/methyl methacrylate(MMA) mixture by pervaporation,the flux and separation factor were(1.27 ± 0.07) kg·M^(-2)·h^(-1) and(4900 ± 1500) at 323 K,respectively.Besides,the NaY zeolite membranes were applied to separate the other short chain alcohol from the various alcohol/organic ester and alcohol/organic ether mixtures,the NaY zeolite membranes showed high short chain alcohol perm-selectivity.

Electroless Plating of Palladium Membranes on Porous Substrates for Hydrogen Separation and the Effects of Process Factors on Plating Rate and Efficiency: A Review

The electroless plating of palladium and palladium alloy membranes is fast becoming an important and enabling technology. This is more so when juxtaposed with the rising demand for high purity hydrogen for applications particularly in proton exchange membrane fuel cells (PEMFC). The effect of process factors such as sensitization and activation during surface modification, concentration of the reducing agent, plating temperature, time, pH, additives, air aeration on plating efficiency, quality of the palladium film and deposit morphology is reviewed with the aim of identifying areas requiring further investigation. The paper also reviews how these process factors could be optimised for better plating efficiency and overall membrane quality. The concentration of the reducing agent has been identified as the limiting factor on plating efficiency albeit other process factors separately impact on the plating efficiency. Furthermore, bulk precipitation caused by concentration of the reducing agent has been identified as a major problem during electroless plating with hydrazine based plating baths. To ameliorate this problem, a multi step addition of the hydrazine reducer in separate portions has been recommended.

Recent advances on the membrane processes for CO_2 separation

Membrane separation technology has popularized rapidly and attracts much interest in gas industry as a promising sort of newly chemical separation unit operation. In this paper, recent advances on membrane processes for CO_2 separation are reviewed. The researches indicate that the optimization of operating process designs could improve the separation performance, reduce the energy consumption and decrease the cost of membrane separation systems. With the improvement of membrane materials recently,membrane processes are beginning to be competitive enough for CO_2 separation, especially for postcombustion CO_2 capture, biogas upgrading and natural gas carbon dioxide removal, compared with the traditional separation methods. We summarize the needs and most promising research directions for membrane processes for CO_2 separation in current and future membrane applications. As the time goes by, novel membrane materials developed according to the requirement proposed by process optimization with increased selectivity and/or permeance will accelerate the industrialization of membrane process in the near future. Based on the data collected in a pilot scale test, more effort could be made on the optimization of membrane separation processes. This work would open up a new horizon for CO_2 separation/Capture on Carbon Capture Utilization and Storage(CCUS).

Synthesis and Microstructure of Doped Alumina Composite Membrane by Sol-Gel Process

The supported membranes of Al 2O 3 and its modification membranes were prepared.Al 2O 3,Al 2O 3 SiO 2 TiO 2 and Al 2O 3 SiO 2 TiO 2 ZrO 2 membranes were mamufatured by the slip casting process using mixing boehmite,silicate,titania and zirconia sols under proper conditions,then the composite membrane was prepared.The structure and characteristics of the membrane were determined by XRD,SEM and AFM measurement.The conditions of preparation of the membrane are discussed.The thickness of the layer is about 1-2μm,the diameter of an average pore is 200-300nm and has a narrow pore distribution without crack forming.By changing the ratios of Al∶Si∶Ti∶Zr(mol),variations of surface pore size of Al 2O 3 SiO 2 TiO 2 ZrO 2 membrane can be gained.

Introducing 3D-potting:a novel production process for artificial membrane lungs with superior blood flow design

Currently,artificial-membrane lungs consist of thousands of hollow fiber membranes where blood flows around the fibers and gas flows inside the fibers,achieving diffusive gas exchange.At both ends of the fibers,the interspaces between the hollow fiber membranes and the plastic housing are filled with glue to separate the gas from the blood phase.During a uniaxial centrifugation process,the glue forms the“potting.”The shape of the cured potting is then determined by the centrifugation process,limiting design possibilities and leading to unfavorable stagnation zones associated with blood clotting.In this study,a new multiaxial centrifugation process was developed,expanding the possible shapes of the potting and allowing for completely new module designs with potentially superior blood flow guidance within the potting margins.Two-phase simulations of the process in conceptual artificial lungs were performed to explore the possibilities of a biaxial centrifugation process and determine suitable parameter sets.A corresponding biaxial centrifugation setup was built to prove feasibility and experimentally validate four conceptual designs,resulting in good agreement with the simulations.In summary,this study shows the feasibility of a multiaxial centrifugation process allowing greater variety in potting shapes,eliminating inefficient stagnation zones and more favorable blood flow conditions in artificial lungs.

Multinanoparticle Translocations in Phospholipid Membranes:Translocation Modes and Dynamic Processes

Multinanoparticles interacting with the phospholipid membranes in solution were studied by dissipative particle dynamics simulation.The selected nanoparticles have spherical or cylindrical shapes,and they have various initial velocities in the dynamical processes.Several translocation modes are defined according to their characteristics in the dynamical processes,in which the phase diagrams are constructed based on the interaction strengths between the particles and membranes and the initial velocities of particles.Furthermore,several parameters,such as the system energy and radius of gyration,are investigated in the dynamical processes for the various translocation modes.Results elucidate the effects of multiparticles interacting with the membranes in the biological processes.

Acid precipitation coupled membrane-dispersion advanced oxidation process(MAOP)to treat crystallization mother liquor of pulp wastewater

Treatment to crystallization mother liquor containing high concentration of organic and inorganic substances is a challenge in zero liquid discharge of industrial wastewater.Acid precipitation coupled membrane-dispersion advanced oxidation process(MAOP)was proposed for organics degradation before salt crystallization by evaporation.With acid-MAOP treatment CODCrin mother liquor of pulping wastewater was eliminated by 55.2%from ultrahigh initial concentration up to 12,500 mg·L^-1.The decolorization rate was 96.5%.Recovered salt was mainly NaCl(83.3 wt%)having whiteness 50 brighter than industrial baysalt of whiteness 45.The oxidation conditions were optimized as CO3=0.11 g·L^-1 and CH2O2=2.0 g·L^-1 with dispersing rate 0.53 ml·min^-1 for 100 min reaction toward acidified liquor of p H=2.Acidification has notably improved evaporation efficiency during crystallization.Addition of H2O2 made through membrane dispersion has eliminated hydroxyl radical"quench effect"and enhanced the degradation capacity,in particular,the breakage of carbon-chloride bonds(of both aliphatic and aromatic).As a result,the proposed coupling method has improved organic pollutant reduction so as the purity of salt from the wastewater mixture which can facilitate water and salt recycling in industry.

Effect of powdered activated carbon on Chinese traditional medicine wastewater treatment in submerged membrane bioreactor with electronic control backwashing

Chinese traditional medicine wastewater, rich in macromolecule and easy to foam in aerobic biodegradation such as Glycosides, was treated by two identical bench-scale aerobic submerged membrane bioreactors （SMBRs） operated in parallel under the same feed, equipped with the same electronic control backwashing device. One was used as the control SMBR （CSMBR） while the other was dosed with powdered activated carbon （PAC） （PAC-amended SMBR, PSMBR）. The backwashing interval was 5 min. One suction period was about 90 min by adjusting preestablished backwashing vacuum and pump frequency. The average flux of CSMBR during a steady periodic state of 24 d （576 h） was 5.87 L/h with average hydraulic residence time （HRT） of 5.97 h and that of PSMBR during a steady periodic state of 30 d （720 h） was 5.85 L/h with average HRT of 5.99 h. The average total chemical oxygen demand （COD） removal efficiency of CSMBR was 89.29% with average organic loading rate （OLR） at 4.16 kg COD/（m^3.d） while that of PSMBR was 89.79% with average OLR at 5.50 kg COD/（m^3.d）. COD concentration in the effluent of both SMBRs achieved the second level of the general wastewater effluent standard GB8978-1996 for the raw medicine material industry （300 mg/L）. Hence, SMBR with electronic control backwashing was a viable process for medium-strength Chinese traditional medicine wastewater treatment. Moreover, the increasing rates of preestablished backwashing vacuum, pump frequency, and vacuum and flux loss caused by mixed liquor in PSMBR all lagged compared to those in CSMBR; thus the actual operating time of the PSMBR system without membrane cleaning was extended by up to 1.25 times in contrast with the CSMBR system, and the average total COD removal efficiency of PSMBR was enhanced with higher average OLR.

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

An anaerobic/oxic membrane bioreactor (A/O MBR) was used for treatment of dyeing wastewater from a woolen mill. COD and color of the wastewater were 54—473 mg/L and 40—400 dilution time (DT) respectively. The ratio of BOD 5/COD was less than 0.13. By the A/O MBR process, the average removal of COD, BOD 5, color and turbidity was 82%, 96%, 71% and 99%, respectively. The average COD, BOD 5, color and turbidity of effluent was 37 mg/L, 0.8 mg/L, 40 DT and 0.44 NUT respectively. The effluent COD met the local standard of reuse water in Beijing, China. The average COD volume load of the anaerobic biological tank was 0.0483 kgCOD/(m 3·d) and that of the aeration tank of the MBR was 0.3589 kgCOD/(m 3·d). The sludge load of the MBR was 0.19 kgCOD/(kg·MLSS·d) on average and the maximum of that was 0.4 kgCOD/(kg·MLSS·d). The flux of the A/O membrane bioreactor could be remained at larger than 50 L/(h·m 2·0.1MPa). The results indicated that A/O membrane bioreactor has technical feasibility for treatment of woolen mill wastewater.