Abrasive wear behaviors of high velocity arc sprayed iron aluminum composite coatings

The High Velocity Arc Spraying （HVAS） technology was used to prepare Fe-Al composite coatings by the adding of different elements into cored wires to obtain different Fe-Al coatings. The added compounds do great effect on the properties of the composite coatings. The microstructures and abrasive wear performances of the coatings were assessed by transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, and THT07-135 high temperature wear equipment. It was found that the adding of Cr3C2 can greatly increase the room temperature wear behavior, and Fe-Al/WC coatings have adapting periods at the beginning of wear experiment. With the rise of temperature, the wear resistance of Fe-AI/Cr3C2 coatings becomes bad from room temperature to 250℃, and then stable from 250℃ to 550℃; the wear resistance of Fe-Al/WC becomes well with the rise of temperature. The adding of Cr and Ni can also improve wear performances of Fe-Al composite coatings.

Fracture Behaviour of Laser Clad Fe-and Ni-base Alloy Coatings on a Cast Iron under SEMI Loading

Laser cladding technique has been applied to renovate some partially-damaged (or worn) components with Fe, Ni, Co-base alloys, hence to improve their hardness values and wear resistance successfully in previous reports. But for some punching or shearing cast iron dies damaged or worn in automobile manufacture, the renovated surfaces also bear some impact loading. Therefore, a small-energy and multi-impact (SEMI) test was designed to investigate the fracture behaviour of renovated cast iron dies achieved by laser cladding of Fe and Ni-base alloys under SEMI loading to meet above requirement. observations show that the fracture took place in the substrate near to the substrate/coating interface rather than at the interface. The tempering temperature has a great influence on the cycles to fracture of laser-clad samples under SEMl loading, i.e. the low tempering temperature of 300℃ gives a maximum cycle to fracture, while a higher tempering temperature of 400℃ has a minimum. Furthermore, the fracture mechanism has also been discussed in present study

Enhancement of Heat-Resistance of Carbonyl Iron Particles by Coating with Silica and Consequent Changes in Electromagnetic Properties

Silica-coated carbonyl iron particles （CIPs） are fabricated with the Stober method to improve their heat-resistance and wave-aSsorption properties. The morphology, heat-resistance, electromagnetic properties and microwave absorption of raw-CIPs and silica-coated CIPs are investigated using a scanning electron microscope, an energy dispersive spectrometer, a thermal-gravimetric analyzer, and a network analyzer. The results show that the heat-resistance of silica-coated CIPs is better than that of raw CIFs. The reflection losses exceeding -lOdB of silica-coated CIPs are obtained in the frequency range 9.5-12.4 GHz for the absorber thickness of 2.3 mm, and the same reflection losses of uncoated CIPs reach the data in the lower frequency range for the same thickness. The enhanced microwave absorption of silica-coated CIPs can be ascribed to the combination of proper electromagnetic impedance match and the decrease of dielectric permittivity.

Pilot Test of the Permeable Reactive Barrier for Removing Uranium from the Flooded Gunnar Pit

This work reports on applying iron oxide coated sand (IOCS) media in an experimental permeable reactive barrier to remove uranium (U) species from uranium containing water. A field study was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/L), Ra-226 (0.4 Bq/L), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca, posing potential environmental and health concerns. IOCS media can be used to immobilize uranium species through an adsorption process. Herein, the preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands is described. Fourier transform infrared spectroscopy (FTIR) and powder X-ray diffraction (pXRD) were used for structural characterization. The adsorption properties of the IOCS sorbent media were modeled by the Langmuir adsorption isotherm, where a maximum uranium uptake capacity was estimated. Bench-scale adsorption kinetic experiments were also performed before moving to a field trial. Based on these lab results and input on field-scale parameters, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier that employs the IOCS media. This approach can be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Influence of rare earths addition on residual stress of Fe-based coating prepared by brush plating technology

The effect of rare earths（La, Ce and Pr） addition on residual stress in iron coatings prepared by brush plating was investigated. The results showed that the addition of rare earth transformed the residual stress in the coating from tensile to compressive. To relieve the residual stress, on the one hand, RE elements segregated at the grain boundaries which restricted the coalescence of the grains and provided more capability of grain deformation. On the other hand, RE elements could purify detrimental element and absorb hydrogen atoms in the coating. Among the three rare earths, elements lanthanum showed the most significant effect on surface morphology and residual stress.

Synthesis and Characterization of SiO_2 Coated γ-Fe_2O_3 Nanocomposite Powder for Hyperthermic Application

SiO2 coated γ-Fe2O3 nanocomposite powder has been successfully synthesized by chemical vapor condensation process and its feasibility on hyperthermic application was investigated in this study. The power loss of SiO2 coated γ-Fe2O3 nanocomposite powder which means the magnetic heating effect under alternative magnetic field was much higher than the single phase γ-Fe2O3 nano powder due to the very fine size under 20 nm and well dispersion in biologically compatible SiO2 matrix. The superparamagnetism and hyperthermic property of SiO2 coated γ-Fe2O3 nanocomposite powder were discussed in terms of microstructural development in this study.