In the wire bonding process of microelectronic packaging,heat affect zone(HAZ)is an important factor governing the loop profile of bonding.The height of loop is affected by the length of the HAZ.Factors governing the ...In the wire bonding process of microelectronic packaging,heat affect zone(HAZ)is an important factor governing the loop profile of bonding.The height of loop is affected by the length of the HAZ.Factors governing the HAZ were studied.To investigate this relationship,experiments were done for various sizes of wire and free air ball(FAB).Electric flame-off(EFO)current, EFO time,EFO gap and recrystallization were also studied.The results show that as the size of FAB becomes larger,the length of HAZ increases.With the increase of EFO current and time,the length of HAZ becomes longer.When FAB forms at the same parameter the length of HAZ becomes shorter with the high temperature of recrystallization.展开更多
Al 7075 and Mg AZ31 alloys were joined by diffusion bonding method. Joining process was performed in pressure range of 10-35 MPa at temperatures of 430-450 ℃ for 60 min under a vacuum of 13.3 MPa. The microstructure ...Al 7075 and Mg AZ31 alloys were joined by diffusion bonding method. Joining process was performed in pressure range of 10-35 MPa at temperatures of 430-450 ℃ for 60 min under a vacuum of 13.3 MPa. The microstructure evaluation, phase analysis and distribution of elements at the interface were done using scanning electron microscopy （SEM）, energy-dispersive X-ray spectroscopy （EDS） and X-ray diffraction （XRD）. The pressure of 25 MPa was determined as the optimum pressure in which the minimum amount of plastic deformation takes place at the joint. Different reaction layers containing intermetallic compounds, such as Al12Mg17, Al3Mg2 andα（Al） solid solution, were observed, in interfacial transition zone （ITZ）. Thickness of layers was increased with increasing the operating temperature. According to the results, diffusion of aluminum atoms into magnesium alloy was more and the interface movement towards the Al alloy was observed. The maximum bond strength of 38 MPa was achieved at the temperature of 440 ℃ and pressure of 25 MPa. Fractography studies indicated that the brittle fracture originated from Al3Mg2 phase.展开更多
In order to investigate the bonding behavior and mechanism of the interface prepared by explosive welding, the bonding interfaces of 0 Crl 8Ni9/16MnR were observed and analyzed by means of optical microscope （OM） , ...In order to investigate the bonding behavior and mechanism of the interface prepared by explosive welding, the bonding interfaces of 0 Crl 8Ni9/16MnR were observed and analyzed by means of optical microscope （OM） , scanning electron microscope （SEM） and electron probe microanalysis （ EPMA ）. It is found that the welding interfaces are wavy due to the wavy explosive loading. There are three kinds of bonding interfaces i. e. big wave, small wave and micro wave. There are a few seam defects and all elements contents are less than both of the base and .flyer plate in the transition zone of big wavy interface. Moreover, some ＂holes＂ result in the lowest bonding strength of big wavy interface nearby the interface in the base plate. All elements contents of the small wavy interface are between two metals, and there are few seam and hole defects, so it is the higher for the bonding strength of small wavy interface. There is no transition zone and defects in the micro wavy interface, so the interface is the best. To gain the high quality small and micro wavy bonding interface the explosive charge should be controlled.展开更多
The key parameters of the adhesive layer of a reinforcing patch are of great significance and affect the ability to suppress crack propagation in an Al–Li alloy patch-reinforced structure.This paper proposes a method...The key parameters of the adhesive layer of a reinforcing patch are of great significance and affect the ability to suppress crack propagation in an Al–Li alloy patch-reinforced structure.This paper proposes a method to determine the key parameters of the adhesive layer of adhesively bonded joints in the Al–Li alloy patch-reinforced structure.A zero-thickness cohesive zone model(CZM)was selected to simulate the adhesive layer’s fracture process,and an orthogonal simulation was designed to compare against the test results.A three-dimensional progressive damage model of an Al–Li alloy patch-reinforced structure with single-lap adhesively bonded joints was developed.The simulation’s results closely agree with the test results,demonstrating that this method of determining the key parameters is likely accurate.The results also verify the correctness of the cohesive strength and fracture energy,the two key parameters of the cohesive zone model.The model can accurately predict the strength and fracture process of adhesively bonded joints,and can be used in research to suppress crack propagation in Al–Li alloy patch-reinforced structures.展开更多
The characteristic of the bond zone between Ni-based alloy light beam surfacing layer(SL)and base metal(BM)was investigated by scanning electron microscope,energy dispersive spectrometer and X-ray diffraction.The resu...The characteristic of the bond zone between Ni-based alloy light beam surfacing layer(SL)and base metal(BM)was investigated by scanning electron microscope,energy dispersive spectrometer and X-ray diffraction.The results show that the bond zone,which consists ofγ-Ni orγ-(Fe,Ni)planar crystal band close to SL andα-Fe bright band close to heat affected zone(HAZ),is actually the transition zone of composition and microstructure between SL and HAZ,and the metallurgical bond interface lies between theα-Fe bright band and HAZ.With the increase of light beam heat input from 2kJ/mm to 4kJ/mm,the width of the bond zone increases from 4μm to 15μm,and the morphology of bond interface changes from zigzag to straight.The formation of bond interface indicates the formation of reliable metallurgical bond between SL and BM.展开更多
The interface of slab track laid in cold regions is prone to debonding under the coupling of freeze-thaw cyclesand temperature loads.Based on the composite specimen tests,the parameters of cohesive zone model were obt...The interface of slab track laid in cold regions is prone to debonding under the coupling of freeze-thaw cyclesand temperature loads.Based on the composite specimen tests,the parameters of cohesive zone model were obtained andused in a simulation model of CRTS III prefabricated slab track to study the interlayer damage.The results show that 1)the digital image correlation(DIC)technique can accurately capture the strain field changes on the interface of compositespecimens under splitting and shear loading;2)when the temperature gradient is−40℃/m−60℃/m,the interfacedamage of the slab track is minimal and presents different patterns of expansion under positive and negative temperaturegradients,each corresponding to damage of the cohesive element dominated by shear stress and normal tensile stress,respectively;3)the reduction of the elastic modulus at the concrete base after freeze-thaw inhibits interface damage andleads to a higher starting temperature gradient load,but cracking can occur on the concrete base after 150 freeze-thaws.For this reason,in the light of damage control of both the interface and concrete base,the elastic modulus of the concretebase is 54%or over that without freeze-thaw cycles.展开更多
基金Project(50705027)supported by the National Natural Science Foundation of ChinaProject(2007AA04Z315)supported by the National High-Tech Research and Development Program of China。
文摘In the wire bonding process of microelectronic packaging,heat affect zone(HAZ)is an important factor governing the loop profile of bonding.The height of loop is affected by the length of the HAZ.Factors governing the HAZ were studied.To investigate this relationship,experiments were done for various sizes of wire and free air ball(FAB).Electric flame-off(EFO)current, EFO time,EFO gap and recrystallization were also studied.The results show that as the size of FAB becomes larger,the length of HAZ increases.With the increase of EFO current and time,the length of HAZ becomes longer.When FAB forms at the same parameter the length of HAZ becomes shorter with the high temperature of recrystallization.
文摘Al 7075 and Mg AZ31 alloys were joined by diffusion bonding method. Joining process was performed in pressure range of 10-35 MPa at temperatures of 430-450 ℃ for 60 min under a vacuum of 13.3 MPa. The microstructure evaluation, phase analysis and distribution of elements at the interface were done using scanning electron microscopy （SEM）, energy-dispersive X-ray spectroscopy （EDS） and X-ray diffraction （XRD）. The pressure of 25 MPa was determined as the optimum pressure in which the minimum amount of plastic deformation takes place at the joint. Different reaction layers containing intermetallic compounds, such as Al12Mg17, Al3Mg2 andα（Al） solid solution, were observed, in interfacial transition zone （ITZ）. Thickness of layers was increased with increasing the operating temperature. According to the results, diffusion of aluminum atoms into magnesium alloy was more and the interface movement towards the Al alloy was observed. The maximum bond strength of 38 MPa was achieved at the temperature of 440 ℃ and pressure of 25 MPa. Fractography studies indicated that the brittle fracture originated from Al3Mg2 phase.
文摘In order to investigate the bonding behavior and mechanism of the interface prepared by explosive welding, the bonding interfaces of 0 Crl 8Ni9/16MnR were observed and analyzed by means of optical microscope （OM） , scanning electron microscope （SEM） and electron probe microanalysis （ EPMA ）. It is found that the welding interfaces are wavy due to the wavy explosive loading. There are three kinds of bonding interfaces i. e. big wave, small wave and micro wave. There are a few seam defects and all elements contents are less than both of the base and .flyer plate in the transition zone of big wavy interface. Moreover, some ＂holes＂ result in the lowest bonding strength of big wavy interface nearby the interface in the base plate. All elements contents of the small wavy interface are between two metals, and there are few seam and hole defects, so it is the higher for the bonding strength of small wavy interface. There is no transition zone and defects in the micro wavy interface, so the interface is the best. To gain the high quality small and micro wavy bonding interface the explosive charge should be controlled.
基金Project(51575535)supported by the National Natural Science Foundation of ChinaProject(2015CX002)supported by the Innovation-driven Plan in Central South University,China+2 种基金Project(zzyjkt2013-09B)supported by the Fund of the State Key Laboratory of High Performance Manufacturing,ChinaProject(2017zzts638)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2016RS2015)supported by the Scientific and Technological Leading Talent Projects of Hunan Province,China
文摘The key parameters of the adhesive layer of a reinforcing patch are of great significance and affect the ability to suppress crack propagation in an Al–Li alloy patch-reinforced structure.This paper proposes a method to determine the key parameters of the adhesive layer of adhesively bonded joints in the Al–Li alloy patch-reinforced structure.A zero-thickness cohesive zone model(CZM)was selected to simulate the adhesive layer’s fracture process,and an orthogonal simulation was designed to compare against the test results.A three-dimensional progressive damage model of an Al–Li alloy patch-reinforced structure with single-lap adhesively bonded joints was developed.The simulation’s results closely agree with the test results,demonstrating that this method of determining the key parameters is likely accurate.The results also verify the correctness of the cohesive strength and fracture energy,the two key parameters of the cohesive zone model.The model can accurately predict the strength and fracture process of adhesively bonded joints,and can be used in research to suppress crack propagation in Al–Li alloy patch-reinforced structures.
基金Item Sponsored by National Natural Science Foundation of China(59905017)
文摘The characteristic of the bond zone between Ni-based alloy light beam surfacing layer(SL)and base metal(BM)was investigated by scanning electron microscope,energy dispersive spectrometer and X-ray diffraction.The results show that the bond zone,which consists ofγ-Ni orγ-(Fe,Ni)planar crystal band close to SL andα-Fe bright band close to heat affected zone(HAZ),is actually the transition zone of composition and microstructure between SL and HAZ,and the metallurgical bond interface lies between theα-Fe bright band and HAZ.With the increase of light beam heat input from 2kJ/mm to 4kJ/mm,the width of the bond zone increases from 4μm to 15μm,and the morphology of bond interface changes from zigzag to straight.The formation of bond interface indicates the formation of reliable metallurgical bond between SL and BM.
基金the State Scholarship Fund(No.201709480008)Hunan Province Education Scientific Project(No.19A164)National Undergraduate Research and Creative Experiment Project(No.S202010534006)。
基金Project(52425213)supported by the National Science Fund for Distinguished Young Scholars of ChinaProjects(52278461,52308467)supported by the National Natural Science Foundation of China+1 种基金Projects(2021YFF0502100,2021YFB2600900)supported by the National Key R&D Program of ChinaProject(2022JDTD0015)supported by the Sichuan Province Youth Science and Technology Innovation Team,China。
文摘The interface of slab track laid in cold regions is prone to debonding under the coupling of freeze-thaw cyclesand temperature loads.Based on the composite specimen tests,the parameters of cohesive zone model were obtained andused in a simulation model of CRTS III prefabricated slab track to study the interlayer damage.The results show that 1)the digital image correlation(DIC)technique can accurately capture the strain field changes on the interface of compositespecimens under splitting and shear loading;2)when the temperature gradient is−40℃/m−60℃/m,the interfacedamage of the slab track is minimal and presents different patterns of expansion under positive and negative temperaturegradients,each corresponding to damage of the cohesive element dominated by shear stress and normal tensile stress,respectively;3)the reduction of the elastic modulus at the concrete base after freeze-thaw inhibits interface damage andleads to a higher starting temperature gradient load,but cracking can occur on the concrete base after 150 freeze-thaws.For this reason,in the light of damage control of both the interface and concrete base,the elastic modulus of the concretebase is 54%or over that without freeze-thaw cycles.
