Structural Isomers:Small Change with Big Difference in Anion Storage

Organic electrode materials are promising for batteries.However,the reported organic electrodes are often facing the challenges of low specific capacity,low voltage,poor rate capability and vague charge storage mechanisms,etc.Isomers are good platform to investigate the charge storage mechanisms and enhance the performance of batteries,which,however,have not been focused in batteries.Herein,two isomers are reported for batteries.As a result,the isomer tetrathiafulvalene(TTF)could store two monovalent anions reversibly,deriving an average discharge voltage of 1.05 V and a specific capacity of 220 mAh g−1 at a current density of 2 C.On the other hand,the other isomer tetrathianaphthalene could only reversibly store one monovalent anion and upon further oxidation,it would undergo an irreversible solid-state molecular rearrangement to TTF.The molecular rearrangement was confirmed by electrochemical performances,X-ray diffraction patterns,nuclear magnetic resonance spectra,and 1H detected heteronuclear multiple bond correlation spectra.These results suggested the small structural change could lead to a big difference in anion storage,and we hope this work will stimulate more attention to the structural design for boosting the performance of organic batteries.

Co-Harvest Phase-Change Enthalpy and Isomerization Energy for High-Energy Heat Output by Controlling Crystallization of Alkyl-Grafted Azobenzene Molecules

Photoisomerization-induced phase change are important for co-harvesting the latent heat and isomerization energy of azobenzene molecules.Chemically optimizing heat output and energy delivery at alternating temperatures are challenging because of the differences in crystallizability and isomerization.This article reports two series of asymmetrically alkyl-grafted azobenzene(Azo-g),with and without a methyl group,that have an optically triggered phase change.Three exothermic modes were designed to utilize crystallization enthalpy(△H_(c))and photothermal(isomerization)energy(△H_(p))at different temperatures determined by the crystallization.Azo-g has high heat output(275-303 J g^(-1))by synchronously releasing△H_(c)and△H_(p)over a wide temperature range(-79℃to 25℃).We fabricated a new distributed energy utilization and delivery system to realize a temperature increase of 6.6℃at a temperature of-8℃.The findings offer insight into selective utilization of latent heat and isomerization energy by molecular optimization of crystallization and isomerization processes.

Li-promoted C_(3)N_(4) catalyst for efficient isomerization of glucose into fructose at 50℃ in water

Efficient and selective glucose-to-fructose isomerization is a crucial step for production of oxygenated chemicals derived from sugars,which is usually catalyzed by base or Lewis acid heterogeneous catalyst.However,high yield and selectivity of fructose cannot be simultaneously obtained under mild conditions which hamper the scale of application compared with enzymatic catalysis.Herein,a Li-promoted C_(3)N_(4) catalyst was exploited which afforded an excellent fructose yield(40.3 wt%)and selectivity(99.5%)from glucose in water at 50℃,attributed to the formation of stable Li–N bond to strengthen the basic sites of catalysts.Furthermore,the so-formed N_(6)–Li–H_(2)O active site on Li–C_(3)N_(4) catalyst in aqueous phase changes the local electronic structure and strengthens the deprotonation process during glucose isomerization into fructose.The superior catalytic performance which is comparable to biological pathway suggests promising applications of lithium containing heterogeneous catalyst in biomass refinery.

Critical approaches in the catalytic transformation of sugar isomerization and epimerization after Fischer-History,challenges,and prospects

The transformation of aldose to ketose or common sugars into rare saccharides,including rare ketoses and aldoses,is of great value and interest to the food industry and for saccharidic biomass utilization,medicine,and the synthesis of drugs.Nowadays,high-fructose corn syrup(HFCS)is industrially produced in more than 10 million tons annually using immobilized glucose isomerase.Some low-calorie saccharides such as tagatose and psicose,which are becoming popular sweeteners,have also been produced on a pilot scale in order to replace sucrose and HFCS.However,current catalysts and catalytic processes are still difficult to utilize in biomass conversion and also have strong substrate dependence in producing high-value,rare sugars.Considering the specific reaction properties of saccharides and catalysts,since the pioneering discovery by Fischer,various catalysts and catalytic systems have been discovered or developed in attempts to extend the reaction pathways,improve the reaction efficiency,and to potentially produce commercial products.In this review,we trace the history of sugar isomerization/epimerization reactions and summarize the important breakthroughs for each reaction as well as the difficulties that remain unresolved to date.

Isomeric fluorescence sensors for wide range detection of ionizing radiations

In order to achieve a wider range of ionizing radiations detection,novel fluorescence sensing materials have been developed that utilize the fluorescence enhancement phenomenon caused by the intramolecular photoinduced electron transfer(PET)effect.Two perylene diimide isomers PDI-P and PDI-B were designed and synthesized,and their molecular structures were characterized by high-resolution Fourier transform mass spectrometry(HRMS),nuclear magnetic resonance hydrogen and carbon spectroscopy(~1H and~(13)C NMR).The interaction between ionizing radiation and fluorescent molecules was simulated by HCl titration.The results show that combining PDIs and HCl can improve fluorescence through the retro-PET process.Despite the similarities in chemical structures,the fluorescent enhancement multiple of PDI-B with aromatic amine as electron donor is much higher than that of PDI-P with alkyl amine.In the direct irradiation experiments of ionizing radiation,the emission enhancement multiples of PDI-P and PDI-B are 2.01 and 45.4,respectively.Furthermore,density functional theory(DFT)and time-dependent density functional theory(TDDFT)calculations indicate that the HOMO and HOMO-1 energy ranges of PDI-P and PDI-B are 0.54 e V and 1.13 e V,respectively.A wider energy range has a stronger driving force on electrons,which is conducive to fluorescence quenching.Both femtosecond transient absorption spectroscopy(fs-TAS)and transient fluorescence spectroscopy(TFS)tests show that PDI-B has shorter charge separation lifetime and higher electron transfer rate constant.Although both isomers can significantly reduce LOD during PET process,PDI-B with aromatic amine has a wider detection range of 0.118—240 Gy due to its larger emission enhancement,which is a leap of three orders of magnitude.It breaks through the detection range of gamma radiation reported in existing studies,and provides theoretical support for the further study of sensitive and effective new materials for ionizing radiation detection.

Developing a highly scalable synthetic strategy for 5-amino-4-nitrobenzo[1,2-c:3,4-c']bis([1,2,5]oxadiazole)1,b-dioxide(CL-18)and investigating the influence of crystal engineering and positional isomerization on its safety and laser ignition performance

5-amino-4-nitrobenzo[1,2-c:3,4-c']bis([1,2,5]oxadiazole)1,6-dioxide(CL-18)exhibits significant potential as an initiating explosive.However,its current synthesis process remains non-scalable due to low yields and safety risks.In this study,we have developed a simple and safe synthetic route for CL-18.It was synthesized from 3,5-dihaloanisole in a four-step reaction with an overall yield exceeding 60%,surpassing all reported yields in the literature.Subsequently,recrystallization of CL-18 was successfully achieved by carefully selecting appropriate solvents and antisolvents to reduce its mechanical sensitivity.Ultimately,when DMF-ethanol was employed as the recrystallization solvent system,satisfactory product yield(>90%)and reduced mechanical sensitivity(IS=15 J;FS=216 N)were obtained.Additionally,CL-18 is derived from the rearrangement of oxygen atoms on i-CL-18 furoxan,and a comparative analysis of their physicochemical properties was conducted.The thermal stability of both compounds is similar,with onset decomposition temperatures recorded at 186 and 182℃respectively.Similarly,they exhibit 5 s breaking point temperatures of 236 and 237℃.Additionally,we present novel insights into the positional-isomerization-laser-ignition performance of CL-18 and its isomer i-CL-18 using laser irradiation for the first time.Remarkably,our findings demonstrate that i-CL-18 exhibits enhanced laser sensitivity,as it can be directly ignited by a 1064 nm wavelength laser,whereas CL-18 lacks this characteristic.

Simulation of nuclear isomer production in laser-induced plasma

Nuclear isomers play essential roles in various fields,including stellar nucleosynthesis,nuclear clocks,nuclear batteries,clean nuclear energy,and-ray lasers.Recent technological advances in high-intensity lasers have made it possible to excite or de-excite nuclear isomers using table-top laser equipment.Utilizing a particle-in-cell code,we investigate the interaction of a laser with a nanowire array and calculate the production rates of the^(73m)Ge(E_(1)=13.3 keV)and^(107m)Ag(E_(1)=93.1 keV)isomers.For^(73m1)Ge,production by Coulomb excitation is found to contribute a peak efficiency of 1.0×10^(19) particles s^(−1)J^(−1),while nuclear excitation by electron capture(NEEC)contributes a peak of 1.65×10^(11)particles s^(−1)J^(−1).These results indicate a high isomeric production ratio,as well as demonstrating the potential for confirming the existence of NEEC,a long-expected but so far experimentally unobserved fundamental process.

Synthesis of Pt/PMA-MIL-101 Catalyst and Its Performance in n-Heptane Isomerization

Hydroisomerization of n-heptane is an efficient method for producing gasoline with a high octane number.The focus of this study was to find a highly efficient catalyst that could both promote the conversion of n-heptane and inhibit the cracking side reaction.MIL-101(Cr)is a chromium-based metal-organic framework(MOF)with good hydrothermal stability,and exhibits a three-dimensional pore structure that is similar to that of zeolites.Using phosphomolybdic acid(PMA;H3PMo12O40·xH2O)can increase the number of Brønsted acid sites on MIL-101(Cr),which contributes to improving the catalytic performance during isomerization.In this study,0.4%Pt/PMA-MIL-101(Cr)catalyst was successfully crystallized at 220℃using a hydrothermal synthetic method.The results showed that the synthesized samples were mesoporousmicroporous composite materials with the typical octahedral structure,and the MIL-101(Cr)framework was not damaged following modification with PMA.It was found that 0.4%Pt30%PMA-MIL-101(Cr)exhibited the best performance for isomerization of n-heptane,with a conversion rate and selectivity at 260°C of 47.6%and 96.6%,respectively.After five hours of reaction,the conversion rate and selectivity of the catalyst remained above 38%and 80%,respectively.

Highly efficient isomerization of glucose to fructose over Sn-doped silica nanotube

Isomerization of glucose to fructose is a fundamental and key intermediate process commonly included in the production of valuable chemicals from carbohydrates in biorefinery.Enhancement of fructose yield is a challenge.In this work,Sn-doped silica nanotube(Sn-SNT)was developed as a highly efficient Lewis acid catalyst for the selective isomerization of glucose to fructose.Over Sn-SNT,69.1%fructose yield with 78.5%selectivity was obtained after reaction at 110◦C for 6 h.The sole presence of a large amount of Lewis acid sites in Sn-SNT without Brønsted acid site is one of the reasons for the high fructose yield and selectivity.Otherwise,high density of SiOH groups in Sn-SNT can ensure the presence of SiOH groups near the Sn sites,which is important for the isomerization of glucose to fructose,leading to the high fructose yield and selectivity.Furthermore,the Sn-SNT is recyclable.

Research on the Relationship between Three Isomers of Microcystins and Environmental Factors

[Objective] The relationship between three isomers of microcystins and environmental factors were studied in the fields.[Method] Three isomers of microcystins （MC-LR,RR and YR） from water of five sampling spots in a northern reservoir were observed for one year with High Performance Liquid Chromatography analytical method in order to study the relationship between three isomers and environmental factors.[Result] The three isomers of microcystins showed positive correlation with chlorophyll a;LR and YR isomers all had significant linear positive correlations with the water temperature,but the RR isomer showed no significant correlation with the water temperature;LR and YR isomers had relatively significantly correlativities with the contents of total nitrogen,nitrate nitrogen and organic nitrogen,while the RR isomer only showed a significant negative correlation with the content of nitrate nitrogen;LR and RR isomers both showed significant positive correlations with the contents of total phosphorus and organic phosphorus,while the phosphorus hardly affected the YR isomer and showed no evident correlation.[Conclusion] The relationship between three isomers of microcystins and environmental factors such as chlorophyll a,water temperature,nitrogen,phosphorus were studied and investigated the reasons,which might offered a reference for controlling the growth of blue algae in water and toxin synthesis.

Experimental and kinetic study of n-heptane isomerization on nanoporous Pt-(Re,Sn)/HZSM5-HMS catalysts

Pt-（Sn,Re）/HZSM5-HMS catalysts were evaluated for n-heptane isomerization at 200–350 ℃.To characterize the catalyst,X-ray diffraction,X-ray fluorescene,Fourier transform infrared spectroscopy,ultraviolet-visible diffuse reflectance spectroscopy,temperature-programmed reduction of H2,temperature-programmed desorption of NH3,infrared spectroscopy of adsorbed pyridine,H2 chemisorption,nitrogen adsorption-desorption,scanning electron microscopy and thermogravimetric analysis were performed.Kinetics of n-C7 isomerization were investigated under various hydrogen and n-C7 pressures,and the effects of reaction conditions on catalytic performance were studied.The results showed that bi-and trimetallic catalysts exhibit better performance than monometallic catalysts for this reaction.For example,a maximum i-C7 selectivity（ 〉74%） and multibranched isomer selectivity（40%） were observed for Pt-Sn/HZSM5-HMS at 200 ℃.

Synthesis of hierarchical SAPO-11-based catalysts with Al-based metal-organic framework derivative as mesoporogen to improve n-decane branched isomerization

Hierarchical SAPO-11 molecular sieve(ACS-11) was successfully synthesized employing the Al2O3/carbon(Al_(2)O_(3)/C) composite obtained through the pyrolysis of Al-based metal-organic framework(Al-MOF-96)as mesoporogen.Unlike other carbon-based mesoporogens with strong hydrophobicity,the Al_(2)O_(3)/C interacts with phosphoric acid and generates the AlPO_(4)/C structure,which promotes the Al2O3/C dispersion in the synthesis gel of SAPO-11 and avoids the phase separation between them.The Al_(2)O_(3)/C as mesoporogen decreases the crystallite size of SAPO-11 via preventing the aggregation of SAPO-11crystals.Additionally,the addition of Al_(2)O_(3)/C improves the Si distribution in the ACS-11 framework.Consequently,ACS-11 has smaller crystallites,more mesopores,and a greater amount of medium Bronsted acid centers than the conventional microporous SAPO-11 and the SAPO-11 synthesized using activated carbon as mesoporogen.The corresponding Pt/ACS-11 catalyst exhibits the maximal selectivity to multi-branched C10isomers(23.28%) and the minimal cracking selectivity(15.83%) in n-decane hydroisomerization among these catalysts.This research provides a new approach for preparing hierarchical silicoaluminophosphate molecular sieve-based catalysts to produce high-quality fuels.

Effects of Rotational Isomerism and Bond Length Alternation on Optical Spectra of FTC Chromophore in Solution

Rotational isomerism effects on the optical spectra of a push-pull nonlinear optical chro-mophore 2-dicyanomethylen-3-cyano-4-f2-[E-（4-N,N-di（2-acetoxyethyl）-amino）-phenylene-（3,4-dibutyl）-thien-5]-E-vinylg-5,5-dimethyl-2,5-dihydrofuran （FTC） in a few solvents have been studied using the time-dependent density functional theory in combination with the polarizable continuum model. It is shown that the maximum absorption peaks of the ro-tamers have difference of nearly 30 nm both in vacuum and in solutions. The population of the rotamers changes a lot in different solvents. Based on the geometries optimized by Hartree-Fock method, the Maxwell-Boltzmann averaged absorption has been calculated and the maximum absorption peak is in good agreement with experiment. It indicates that the bond length alternation can have an important effect on the optical spectra.

n-Nonane hydroisomerization over hierarchical SAPO-11-based catalysts with sodium dodecylbenzene sulfonate as a dispersant

To enhance the gasoline octane number,low-octane linear n-alkanes should be converted into their high-octane di-branched isomers via n-alkane hydroisomerization.Therefore,hierarchical SAPO-11-based catalysts are prepared by adding different contents of sodium dodecylbenzene sulfonate(SDBS),and they are applied in n-nonane hydroisomerization.When n(SDBS)/n(SiO2)is less than or equal to 0.125,the synthesized hierarchical molecular sieves are all pure SAPO-11,and as the SDBS content increases,the submicron particle size decreases,and the external surface area(ESA)increases.Additionally,these hierarchical SAPO-11 have smaller submicron particles and higher ESA values than conventional SAPO-11.When n(SDBS)/n(SiO2)is greater than 0.125,with increasing SDBS content(n(SDBS)/n(SiO2)=0.25),the synthesized SAPO-11 contains amorphous materials,which leads to a decline in the ESA;with the further increase in SDBS content(n(SDBS)/n(SiO2)=0.5),the products are all amorphous materials.These results indicate that in the case of n(SDBS)/n(SiO2)=0.125,the synthesized SAPO-11 molecular sieve(S–S3)has the most external Brønsted acid centers and the highest ESA of these SAPO-11,and these advantages favor generation of the di-branched isomers in hydrocarbon hydroisomerization.Among these Pt/SAPO-11 catalysts,Pt/S–S3 displays the highest selectivity to entire isomers(83.4%),the highest selectivity to di-branched isomers(28.1%)and the minimum hydrocracking selectivity(15.7%)in n-nonane hydroisomerization.

EFFECT OF NITRATE AND PHOSPHATE ON ACCUMULATION OF β-CAROTENE ISOMERS IN DUNALIELLA SALINA

DunaIiella salina, a halotolerent unicellular green alga, can accurmulate a Iarge amount of β-caroteneunder environmental conditions. The isorners of β-carotene extIacted from D. salina culturedin medium with different nitrate and phosphate concentrations were analysed by HPLC with Alox-Talumins column. At least six isomers were found in different proportions depending on the culture me-dia’s nitrate and/or phosphate concentrations. Nitrate and/or phosphae defidency was conducive tothe accumulation of totaI cis isomers but not of al1 trans isomer. lt is sUggeSted that 1 mmol/L KNO3and 0.1 mmol/L KH2, PO4 are favourable for accumulation of total cis β-carotene.

Two Novel Isomers of HPS3 System

Two new isomers of HPS3 system, HP(S)S2 and HSSPS, are predicted by means of B3LYP method with 6-311++G(3df,3pd) basis set. The two isomers can isomerize into thermodynamically the most stable species HSPS2, which have been experimentally identified, with relatively higher reaction barriers. In view of their higher thermodynamical and kinetic stability and the experimental observation for HP(O)O2 and HOOPO in previous study, we can reasonably believe that the two species can be spectrosymmetrically characterized in future experiments.

Classifying Cardiac Anomalies in Right and Left Isomerism:Concordant and Discordant Patterns

Aims:Evidence is emerging that,in the setting of isomerism,the atrial and bronchial arrangement are not always concordant,nor are these patterns always harmonious with the arrangement of the abdominal organs.We aimed to evaluate the concordance between these features in a cohort of patients with cardiac malformations in the setting of known isomerism,seeking to determine whether it was feasible to assess complexity on this basis,in this regard taking note of the potential value of bronchial as opposed to appendage morphology.Methods and Results:We studied 78 patients known to have isomerism of the bronchuses,43 with right and 35 with left isomerism.Appendage anatomy could be determined in 49 cases(63%),all but one of these being concordant with bronchial anatomy.When assessing abdominal features,in only 59 cases(76%)was splenic morphology in keeping with the thoracic findings.As expected,right isomerism was associated with greater complexity of cardiac malformations,with an odds ratio of 6.53,with confidence intervals from 2.2–19.3(p<0.001).The odds were slightly decreased with thoraco-abdominal disharmony,when lesions shown to carry higher risk were then found in the setting of left isomerism.Conclusion:Harmony is excellent between bronchial and appendage isomerism,but less so with the arrangement of the abdominal organs.Right isomerism in our cohort,was indicative of a sixfold increase in intracardiac complexity.When discordance was found between the systems,however,the cardiac anomalies were less typical of the anticipated findings for right vs.left isomerism of the appendages.

Theoretical investigation on isomer formation probability and free energy of small C clusters

Molecular dynamics simulations and free energy calculations are employed to investigate the evolution, formation probability, detailed balance, and isomerization rate of small C cluster isomer at 2500 K. For C10, the isomer formation probability predicted by free energy is in good agreement with molecular dynamics simulation. However, for C20, C3o, and C36, the formation probabilities predicted by free energy are not in agreement with molecular dynamics simulations. Although the cluster systems are in equilibrium, detailed balance is not reached. Such results may be attributed to high transformation barriers between cage, bowl, and sheet isomers. In summary, for mesoscopic nanosystems the free energy criterion, which commonly holds for macroscopic systems in dynamic equilibrium, may not provide a good prediction for isomer formation probability. New theoretical criterion should be further investigated for predicting the isomer formation probability of a mesoscopic nanosystem.

Selective 3-OH Isomerization of Resibufogenin by Cell Suspension Cultures of Ginkgo biloba

Aim To modify the structure of resibufogenin by using Ginkgo bilobasuspension. Methods Young leaves of Ginkgo biloba were differentiated into callus in MS medium withonly 2,4-D as plant growth regulator. The callus was then transferred aseptically to liquid MSmedium exoge-nously supplemented with appropriate concentration of 6-BA, NAA and 2,4-D to establishsuspension cell culture system. Resibufogenin was administered into the well-grown cell cultures andincubated for 4 d. The products dissolved in the liquid phase of the cultures were extracted andpurified by silica gel column chromatography gradiently eluted with petroleum ether and acetonesystem. Results One transformed product was obtained in 40% yield after 4 d incubation, which wasidentified as 3-epi-resibufogenin on the basis of FAB MS, ~1H NMR and ^(13)C NMR spectroscopicanalysis and corresponding data reported in literature. Conclusion G. biloba suspension cultures canbe used as an enzyme system to biotransform resibufogenin, an animal-originated bufadienolide, into3-epi-resibufogenin.

Isomerization of linear C5–C7 over Pt loaded on protonated fibrous silica@Y zeolite（Pt/HSi@Y）

A novel fibrous silica Y zeolite (HSi@Y) loaded with Pt has been studied based on its ability to produce protonic acid sites originating from molecular hydrogen. The Pt/HSi@Y was prepared using seed assisted crystallization followed by protonation and Pt-loading. The product formed had a spherical morphology with bicontinuous lamellar with a diameter in the range of 500-700 nm. The catalytic activity of the Pt/HSi@Y has been assessed based on light linear alkane (C5-C7) isomerization in a micro-catalytic pulse reactor at 423-623 K. A pyridine IR study confirmed that the introduction of fibrous silica on Y zeolite increased the Lewis acid sites corresponding with the formation of extra-framework Al which led to the generation of more protonic acid sites. A hydrogen adsorbed IR study showed that the protonic acid sites which act as active sites in the isomerization were formed via dissociative-adsorption of molecular hydrogen releasing electrons to the nearby Lewis acid sites. Thus, it is suggested that the presence of Pt and HSi@Y with a high number of Lewis acid as well as weak Bronsted acid sites improved the activity and stability in C5, C6 and C7 isomerization via hydrogen spill-over mechanism.