Aerodynamic coefficient of vehicle-bridge system by wind tunnel test

The changes of three components of aerodynamic force were discussed with the attack angle conversion for three kinds of section models. Based on the project of Shanghai Yangtze River Bridge, the wind tunnel test was conducted to obtain its three components of aerodynamic force including 75 conditions of the construction stage, the bridge without vehicles and the bridge with vehicles from - 12 degrees to ＋ 12 degrees. For the bridge with vehicles, the drag force coefficient and the absolute value of both lift coefficient and moment coefficient were decreased by the vehicles. The test resuh shows that the bridge railing and vehicles have much influence on the three components of aerodynamic force of the vehicle-bridge system for Shanghai Yangtze River Bridge.

An Investigation into the Effects of the Reynolds Number on High-Speed Trains Using a Low Temperature Wind Tunnel Test Facility

A series of tests have been conducted using a Cryogenic Wind Tunnel to study the effect of Reynolds number(Re)on the aerodynamic force and surface pressure experienced by a high speed train.The test Reynolds number has been varied from 1 million to 10 million,which is the highest Reynolds number a wind tunnel has ever achieved for a train test.According to our results,the drag coefficient of the leading car decreases with higher Reynolds number for yaw angles up to 30º.The drag force coefficient drops about 0.06 when Re is raised from 1 million to 10 million.The side force is caused by the high pressure at the windward side and the low pressure generated by the vortex at the lee side.Both pressure distributions are not appreciably affected by Reynolds number changes at yaw angles up to 30°.The lift force coefficient increases with higher Re,though the change is small.At a yaw angle of zero the down force coefficient is reduced by a scale factor of about 0.03 when the Reynolds number is raised over the considered range.At higher yaw angles the lift force coefficient is reduced about 0.1.Similar to the side force coefficient,the rolling moment coefficient does not change much with Re.The magnitude of the pitching moment coefficient increases with higher Re.This indicates that the load on the front bogie is higher at higher Reynolds numbers.The yawing moment coefficient increases with Re.This effect is more evident at higher yaw angles.The yawing moment coefficient increases by about 6%when Re is raised from 1 million to 10 million.The influence of Re on the rolling moment coefficient around the leeward rail is relatively smaller.It increases by about 2%over the considered range of Re.

Aerodynamic characteristics of rigid coaxial rotor by wind tunnel test and numerical calculation

Focusing on aerodynamic characteristics of rigid coaxial rotor of a high-speed helicopter in hover and forward flight, a wind tunnel test is conducted in the 8 m ? 6 m low-speed straightflow wind tunnel of China Aerodynamics Research and Development Center. In the experiment,a 4 m diameter composite model rigid coaxial rotor is designed and manufactured, and firstorder flapping frequency ratio of the blade is 1.796 to ensure sufficient stiffness at the blade root.Rotor aerodynamic performance is measured under hovering and high advance ratio conditions.Also, the numerical method is used to calculate aerodynamic characteristics in typical states of the rigid coaxial rotor for analysis purpose. The rotor lift-drag ratio and lateral lift offset in the experiment are emphatically analyzed for the rigid coaxial rotor. The results indicate that in forward flight condition, the rotor lift-drag ratio first increases and then decreases with the increment of advance ratio and lift offset. When advance ratio remains constant, with the increment of lift offset, the lift-drag ratio of rigid coaxial rotor first increases and then decreases.

High-speed wind tunnel test of the CAE aerodynamic validation model

For the purpose of establishing and validating aerodynamic performance predictions at transonic Mach numbers, a wind tunnel test was conducted in the High-Speed Tunnel（HST） of the German-Dutch Wind Tunnels. The test article is the aerodynamic validation model from the Chinese Aeronautical Establishment, which is a full-span scale model representation of a business jet aircraft. The wind tunnel test comprised of parallel deployments of balance, pressures, infrared thermography, and model marker measurement techniques. Dedicated investigations with a dummy support were conducted as well, in order to derive and correct for the interference that the support system imposed on the overall model loads. This enabled the establishment of a comprehensive dataset in which the steady overall model loads, the wing load distribution, the state of the wing boundary layer, and the aeroelastic wing shape were quantified for conditions up to and beyond the cruise Mach number of 0.85.

Wind tunnel tests on aerodynamic characteristics of vehicles on same-storey highway and rail bridge under crosswind

In recent years,the safety and comfort of road vehicles driving on bridges under crosswinds have attracted more attention due to frequent occurrences of wind-induced disasters.This study focuses on a container truck and CRH2 high-speed train as research targets.Wind tunnel experiments are performed to investigate shielding effects of trains on aerodynamic characteristics of trucks.The results show that aerodynamic interference between trains and trucks varies with positions of trains(upstream,downstream)and trucks(upwind,downwind)and numbers of trains.To summarize,whether the train is upstream or downstream of tracks has basically no effect on aerodynamic forces,other than moments,of a truck driving on windward sides of bridges(upwind).In contrast,the presence of trains on the bridge deck has a significant impact on aerodynamic characteristics of a truck driving on leeward sides(downwind)at the same time.The best shielding effect on lateral forces of trucks occurs when the train is located downstream of tracks.Finally,the pressure measuring system shows that only lift forces on trains are affected by trucks,while other forces and moments are primarily affected by adjacent trains.

Wind tunnel study of aerodynamic wind loading on middle pylon of Taizhou Bridge

Segment sectional model tests are carried out to investigate the wind loading on middle pylon of Taizhou Bridge, which has complicated three-dimensional flow due to its feature of double columns. Through the force measuring tests, aerodynamic force coefficients of every segment of the pylon columns have been obtained. It is found that the tested aerodynamic force coefficients are much smaller than those given by codes. The interference effects of aerodynamic force coefficients between columns of pylon are discussed. The results show that the interference effect is the most evident when the yaw angle is about 30 ° from transverse direction. This kind of interference effect can be described as diminutions in transverse aerodynamic force coefficients and magnifications in longitudinal aerodynamic force coefficients of downstream columns.

Wind Tunnel Test and Numerical Computation on Ice Accretion on Blade Airfoil for Straight-bladed VAWT

To invest the condition of ice accretion on the blade used for straight-bladed vertical axis wind turbine （SB-VAWT）, wind tunnel tests were carried out on a blade with NACA0015 airfoil by using a small simple icing wind tunnel. Tests were carried out at some typical attack angles under different wind speeds and flow discharges of a water spray with wind. The icing shape and area on blade surface were recorded and measured, Then the numerical computation was carded out to calculate the lift and drag coefficients of the blade before and after ice accretion according to the experiment result, the effect of icing on the aerodynamic characteristics of blade were discussed.

Wind Tunnel Test on the Wind-Resistant Behavior of a Long-Span Cable-Stayed Bridge during Erection

In order to investigate the aerodynamic behavior of the Sutong bridge over Yangtze River during erection, a 1：50 sectional model of the bridge deck, a 1： 100 full aeroelastic model of the free standing pylon and a 1： 125 full aeroelastic model for the maxim cantilever configuration were built. The test results show that there was no serious vortex-induced vibration at the bridge deck, and that the free standing tower, the model scale and the turbulence intensity influenced static loading. The buffeting responses during the maximum cantilever configuration did not affect the safety of the bridge under construction.

Experimental Investigation of Reynolds Number Effect on Wind Turbine Profiles in the Cryogenic Wind Tunnel Cologne DNW-KKK

Wind turbine size has increased continuously and correspondingly also its Reynolds numbers. The Reynolds number effect can therefore no longer be ignored in design and optimization of wind turbines. Reliable profile test data should be available. A suitable facility for testing wind turbine profiles at high Reynolds numbers is the Cryogenic Wind Tunnel Cologne DNW-KKK. By means of injecting liquid nitrogen the tunnel can be cooled down to 100 K and the Reynolds number therefore can be raised accordingly. The maximum Reynolds number for 2D profile tests can reach 27x10^6. In this paper the test uncertainty and the flow quality of DNW-KKK were analyzed. Then some test results on the Reynolds number effect of the wind turbine profiles will be presented. The Reynolds number effect is different from model to model. Especially for thick profiles and flow control devices the Reynolds number effect is not always like the description in literature.

Aerodynamic characteristics of store during lateral jet assisted separation from cavity using free drop technique

Aimed at the problem of store separation from internal cavity,this paper innovatively puts forward a separation scheme of using lateral jet to assist store safe separation.The jet ensures that the store is continuously subjected to down head moment during separation,so as to ensure safe separation.The wind tunnel free drop test technique with lateral jet is established,which can ensure that there is no support interference in the motion process of the store and more truly simulate the motion of the store.The feasibility of the new separation scheme is proved by wind tunnel test.The test shows that the new scheme can also change the more dangerous state into a safe state.Through the analysis of the test data,the pitching moment coefficients of the store under different pressures in the high-pressure cylinder are obtained,and the effects of aircraft and cavity on the pitching moment of the store are obtained.The 3 stages of store passing through cavity shock wave are found.The results show that the lateral jet provides the store with continuous head down moment,and makes the store overcome the head up moment caused by the shock wave in front of the cavity,so as to ensure the safety of separation.

Experimental investigations on cavity-actuated under-expanded supersonic oscillating jet

As one type of potential flow control actuators, cavity-actuated supersonic jet oscillators, which consist of a 2-D convergent nozzle and two face to face cavities, need to be investigated dee- ply to get the knowledge of their oscillating feature and underlying mechanism. Wind tunnel testing are conducted under different back pressures in a vacuum-type wind tunnel for two supersonic jet oscillators, to obtain their characteristics and the conditions for jet oscillating. The experimental results show that the continuous, nearly symmetric or asymmetric flipping between the two cavities appears over certain nozzle pressure ratio （NPR） range for both oscillators according to schlieren visualizations. Compared to the free jet, the oscillating jet with large exit achieves larger mixing; the oscillating jet with small exit has less mixing, based on the analysis of jet axial peak velocity and the entrainment. The cross-junction mode for estimating the resonance frequency in a pipe with two closed side branches is modified and obtained comparable estimations of the frequency of jet flipping with experimental data, but further investigations are needed to discover the underlying mechanism for the jet flipping.

Review of aerodynamics of high-speed train-bridge system in crosswinds

Serviceability and running safety of the high-speed train on/through a bridge are of major concern in China. Due to the uncertainty chain of the train dynamic analysis in crosswinds originating mainly from the aerodynamic assessment, this paper primarily reviews five meaningful progresses on the aerodynamics of the train-bridge system done by Wind Tunnel Laboratory of Central South University in the past several years. Firstly, the flow around the train and the uncertainty origin of the aerodynamic assessment are described from the fluid mechanism point of view. After a brief introduction of the current aerodynamic assessment methods with their strengths and weaknesses, a new-developed TRAIN-INFRASTRUCTURE rig with the maximum launch speed of 35 m/s is introduced. Then, several benchmark studies are presented, including the statistic results of the characterized geometry parameters of the currently utilized bridge-decks, the aerodynamics of the train, and the aerodynamics of the flat box/truss bridge-decks. Upon compared with the foregoing mentioned benchmarks, this paper highlights the aerodynamic interference of the train-bridge system associated with its physical natures. Finally, a porosity-and orientation-adjustable novel wind barrier with its effects on the aerodynamics of the train-bridge system is discussed.

Effects of wind barriers on the aerodynamic characteristics of bridge-train system for a road-rail same-story truss bridge

Wind barriers are commonly adopted to prevent the effects of wind on high-speed railway trains,but their wind-proofing effects are greatly affected by substructures.To investigate the effects of wind barriers on the aerodynamic characteristic of road-rail same-story truss bridge-train systems,wind tunnel experiments were carried out using a 1:50 scale model.Taking a wind barrier with a porosity of 30%as an example,the aerodynamic characteristics of the bridge train system under different wind barrier layouts(single-sided and double-sided),positions(inside and outside)and heights(2.5 m,3.0 m,3.5 m and 4.0 m)were tested.The results indicate that the downstream inside wind barrier has almost no effect on the aerodynamic characteristics of the train-bridge system,but the downstream outside wind barrier increases the drag coefficient of the bridge and reduces both the lift coefficient and drag coefficient of the train due to its effect on the trains wind pressure distribution,especially on the trains leeward surface.When the wind barriers are arranged on the outside,their effects on the drag coefficient of the bridge and shielding effect on the train are greater than when they are arranged on the inside.As the height of the wind barrier increases,the drag coefficient of the bridge also gradually increases,and the lift coefficient and drag coefficient of the train gradually decrease,but the degree of variation of the aerodynamic coefficient with the height is slightly different due to the different wind barrier layouts.When 3.0 m high double-sided wind barriers are arranged on the outside of the truss bridge,the drag coefficient of the bridge only increases by 12%,while the drag coefficient of the train decreases by 55%.

Refined Aerodynamic Test of Wide-Bodied Aircraft and Its Application

The large dual-channel wide-bodied aircraft has a long range and a high cruise Mach number.Therefore,its aerodynamic design requires a high level ofwind tunnel test refinement.Based on the requirements of aerodynamic design for the future wide-bodied aircraft and the characteristics of high-speed wind tunnel tests,the error theory is introduced to analyze the factors affecting the accuracy of the test data.This study carries out a series of research on the improvement of refined aerodynamic test technology in an FL-26 wind tunnel,including design and optimization of the support system of wide-bodied aircraft,model attitude angle measurement,Mach number control accuracy,measurement and control system stability,test data correction and perfection,high-precision force balance and standard model development.In addition,the effect of the standard specification of the refined aerodynamic test is investigated to improve the data quality.The research findings have been applied in the standard model test and subsequent models of wide-bodied aircraft.The results show that whenMach numbers are less than 0.9,the control accuracy of Mach numbers in the FL-26 wind tunnel is smaller than 0.001 and the measurement error of attack angle is smaller than 0.01°.Therefore,it has the ability to correct the data influenced by factors,such as support/wall interference,model deformation,floating resistance and airflow deflection angle.The repeatability accuracy of the standard model’s comparison test shows that the lift coefficient is less than or equal to 0.0012,the drag coefficient is less than or equal to 0.00004,pitching moment coefficient is less than or equal to 0.0004.The bending resolution of the model’s deformation measurement is less than 0.2 mm,and the tensional deformation is smaller than 0.04°.The revised aerodynamic data and model deformation measurement results have good agreement with that of the ETW wind tunnel.The results demonstrate that the improved technology presented in this paper can significantly enhance the refined aerodynamic test of wide-bodied aircraft.

A Wind Tunnel Two-Dimensional Parametric Investigation of Biplane Configurations

This paper presents an experimental and systematic investigation about how geometric parameters on a biplane configuration have an influence on aerodynamic parameters. This experimental investigation has been developed in a two-dimensional approach. Theoretical studies about biplanes configurations have been developed in the past, but there is not enough information about experimental wind tunnel data at low Reynolds number. This two-dimensional study is a first step to further tridimensional investigations about the box wing configuration. The main objective of the study is to find the relationships between the geometrical parameters which present the best aerodynamic behavior： the highest lift, the lowest drag and the lowest slope of the pitching moment. A tridimensional wing-box model will be designed following the pattern of the two dimensional study conclusions. It will respond to the geometrical relationships that have been considered to show the better aerodynamic behavior. This box-wing model will be studied in the aim of comparing the advantages and disadvantages between this biplane configuration and the plane configuration, looking for implementing the box-wing in the UAV＇s field. Although the box wing configuration has been used in a small number of existing UAV, prestigious researchers have found it as a field of high aerodynamic and structural potential.

Numerical simulation of aerodynamic derivatives and critical wind speed for long-span bridges based on simplified steady wind field

Combining the computational fluid dynamics-based numerical simulation with the forced vibration technique for extraction of aerodynamic derivatives, an approach for calculating the aerodynamic derivatives and the critical flutter wind speed for long-span bridges is presented in this paper. The RNG k-ε turbulent model is introduced to establish the governing equations, including the continuity equation and the Navier-Stokes equations, for solving the wind flow field around a two-dimensional bridge section. To illustrate the effectiveness and accuracy of the proposed approach, a simple application to the Hume Bridge in China is provided, and the numerical results show that the aerodynamic derivatives and the critical flutter wind speed obtained agree well with the wind tunnel test results.

Aerodynamic characteristics of moving vehicles of two trains passing each other on bridge under crosswinds

Two trains passing each other is controlling factor for the wind-vehicle-bridge systems.To test the aerodynamic characteristics of moving vehicles under crosswinds when two trains are passing each other,a wind tunnel test device,which has two moving tracks,was developed.The rationality of the test result was discussed,the effects of intersection mode,yaw angle and lane spacing on the aerodynamic coefficients of the leeward train were analyzed,and the difference of aerodynamic coefficients between the head vehicle and the tail vehicle was discussed.The results show that the proposed test device has good repeatability.The intersection modes have a certain effect on the aerodynamic force of the leeward train when two trains are passing each other,and the results should be more reasonable during the two trains dynamic passing each other.With the decrease of yaw angle,the sudden change of train aerodynamic coefficients is more obvious.The decrease of lane spacing will increase the sudden change of leeward vehicles.In the process of two trains passing each other,the aerodynamic coefficients of the head vehicle and tail vehicle are significantly different,so the coupling vibration analysis of wind-vehicle-bridge system should be considered separately.

Numerical and Experimental Analysis of the Aerodynamic Torque for Axle-Mounted Train Brake Discs

As the velocity of a train increases,the corresponding air pumping power consumption of the brake discs increases proportionally.In the present experimental study,a standard axle-mounted brake disc with circumferential pillars was analyzed using a 1:1 scale model and a test rig in a wind tunnel.In particular,three upstream velocities were selected on the basis of earlier investigations of trains operating at 160,250,and 400 km/h,respectively.Moreover,3D steady computational fluid dynamics(CFD)simulations of the flow field were conducted to compare with the wind tunnel test outcomes.The results for a 3-car train at 180 km/h demonstrated:(1)good agreement between the air resistance torques obtained from the wind tunnel tests and the related numerical results,with differences ranging from 0.95%to 5.88%;(2)discrepancies ranging from 3.2 to 3.8 N·m;(3)cooling ribs contributing more than 60%of the air resistance torque;(4)the fast rotation of brake discs causing a significantly different flow field near the bogie area,resulting in 25 times more air pumping power loss than that obtained in the stationary brake-disc case.

Aerodynamic Interpolation for Flight Vehicles with Aerodynamic Axial Asymmetry

Aim To study wind tunnel test data interpolation methods for flight vehicle with aerodynamic axial asymmetry. Methods For different body aerodynamic roll angles, proper wind tunnel test schemes were selected and trigonometric series were used for aerodynamic interpolation. Results and Conclusion A simple and effective scheme for wind tunnel test and an accurate aerodynamic interpolation method are developed with satisfactory results.

Model Aerodynamic Tests with a Wire-driven Parallel Suspension System in Low-speed Wind Tunnel

Owing to the advantages of wire-driven parallel manipulator, a new wire-driven parallel suspension system for airplane model in low-speed wind tunnel is constructed, and the methods to measure and calculate the aerodynamic parameters of the airplane model are studied. In detail, a static model of the wire-driven parallel suspension is analyzed, a mathematical model for describ- ing the aerodynamic loads exerted on the scale model is constructed and a calculation method for obtaining the aerodynamic parameters of the model by measuring the tension of wires is presented. Moreover, the measurement system for wire tension and its corresponding data acquisition system are designed and built. Thereafter, the wire-driven parallel suspension system is placed in an open return circuit low-speed wind tunnel for wind tunnel tests to acquire data of each wire tension when the airplane model is at different attitudes and different wind speeds. A group of curves about the parameters for aerodynamic load exerted on the airplane model are obtained at different wind speeds after the acquired data are analyzed. The research results validate the feasibility of using a wire-driven parallel manipulator as the suspension system for low-speed wind ttmnel tests.