Hydraulic modeling and optimization of jet mill bit considering the characteristics of depressurization and cuttings cleaning

A jet mill bit(JMB)is proposed to increase the drilling efficiency and safety of horizontal wells,which has the hydraulic characteristics of depressurization and cuttings cleaning.This paper fills the gap in the hydraulic study of the JMB by focusing on the hydraulic modeling and optimization of the JMB and considering these two hydraulic characteristics.First,the hydraulic depressurization model and the hydraulic cuttings cleaning model of the JMB are developed respectively.In the models,the pressure ratio and efficiency are chosen as the evaluation parameters of the depressurization capacity of the JMB,and the jet hydraulic power and jet impact force are chosen as the evaluation parameters of cuttings cleaning capacity of the JMB.Second,based on the hydraulic models,the effects of model parameters[friction loss coefficient,target inclination angle,rate of penetration(ROP),flow ratio,and well depth]on the hydraulic performance of the JMB are investigated.The results show that an increase in the friction loss coefficient and target inclination angle cause a significant reduction in the hydraulic depressurization capacity,and the effect of ROP is negligible.The flow ratio is positively related to the hydraulic cuttings cleaning capacity,and the well depth determines the maximum hydraulic cuttings cleaning capacity.Finally,by combining the hydraulic depressurization model and hydraulic cuttings cleaning model,an optimization method of JMB hydraulics is proposed to simultaneously maximize the jet depressurization capacity and the cuttings cleaning capacity.According to the drilling parameters given,the optimal values of the drilling fluid flow rate,backward nozzle diameter,forward nozzle diameter,and throat diameter can be determined.Moreover,a case study is conducted to verify the effectiveness of the optimization method.

Theoretical and experimental study of the pulling force of jet bits in radial drilling technology

Radial drilling technology, of which the jet bit is the key device, is a research focus in the field of oil drilling and production. This paper establishes mechanical equations for jet bits and analyzes the hydroseal of backward jets in bottom holes. Meanwhile this paper establishes a mechanical equation for a high pressure hose and analyzes the axial force distribution. Laboratory experiments indicate that the flow rate, the angle between the backward nozzle axis and the jet bit axis, and the hole diameter are the major influencing factors; the generation of the pulling force is mainly due to the inlet pressure of the jet bit; the backward jets can significantly increase not only the pulling force but also the stability of jet bits. The pulling force would reach 8,376 N under experimental conditions, which can steadily pull the high-pressure hose forward.

Numerical and experimental investigation on the depressurization capacity of a new type of depressure-dominated jet mill bit

Efficient cuttings transport and improving rate of penetration(ROP)are two major challenges in horizontal drilling and extended reach drilling.A type of jet mill bit(JMB)may provide an opportunity to catch the two birds with one stone:not only enhancing cuttings transport efficiency but also improving ROP by depressuring at the bottom hole.In this paper,the JMB is further improved and a new type of depressure-dominated JMB is presented;meanwhile,the depressurization capacity of the depressure-dominated JMB is investigated by numerical simulation and experiment.The numerical study shows that low flow-rate ratio helps to enhance the depressurization capacity of the depressure-dominated JMB;for both depressurization and bottom hole cleaning concern,the flow-rate ratio is suggested to be set at approximately 1:1.With all other parameter values being constant,lower dimensionless nozzle-to-throat-area ratio may result in higher depressurization capacity and better bottom hole cleaning,and the optimal dimensionless nozzle-to-throat-area ratio is at approximately0.15.Experiments also indicate that reducing the dimensionless flow-rate ratio may help to increase the depressurization capacity of the depressure-dominated JMB.This work provides drilling engineers with a promising tool to improve ROP.

A new method of combined rock drilling

Based on the technologies of traditionally mechanical drilling and water jet,we propose a new method of abrasive water jet in combination with rock drilling,and establish a combined rock drilling system for the gas pre-drainage.This study chose the common sandstone and silicon limestone as the rock sample.A series of experiments were completed in the case of dry drilling,existing technology drilling,combined drilling with high pressure water jet and combined drilling with abrasive water jet,respectively.The drilling efficiency and performance were contrasted and analyzed in detail.The results indicate that it is better to choose the method of combined drilling with the high-pressure water jet for soft rocks.The method of combined drilling with abrasive water jet is feasible for the hard rock drilling and has higher drilling efficiency and performance.In this paper,compared with the existing technology,the drilling depth has increased by about 65%,the axial force and torque have reduced by about 14%and 17%,respectively,and the drill wear reduces obviously in the same conditions.