Surface grain refinement mechanism of SMA490BW steel cross joints by ultrasonic impact treatment

Ultrasonic impact treatment (UIT) is a postweld technique for improving the fatigue strength of welded joints. This technique makes use of ultrasonic vibration to impact and plastically deform a weld toe and can achieve surface grain refinement of the weld toe, which is considered as the main reason for the improvement of fatigue strength. In this paper, the microstructure of the surface of a treated weld toe was observed by metallographic microscopy and transmission electron microscopy (TEM). The results show that UIT could produce severe plastic deformation on the surface layer of the weld toe and the maximum depth of plastic deformation extended to approximately 260 μm beneath the treated surface. Repeated processing could exacerbate the plastic deformation on the surface layer, resulting in finer grains. We can conclude that the surface grain refinement mechanism of SMA490BW welded joints is related to the high density of dislocation tangles and dislocation walls. © 2017, University of Science and Technology Beijing and Springer-Verlag Berlin Heidelberg.

CALCULATION OF THREE－DIMENSIONAL SOLDER JOINT FORMATION IN MICROELECTRONIC SURFACE MOUNT TECHNOLOGY

A finite element analysis for calculating three-dimensional(3-D) solder joint shape between chip component and substrate pad was carried out, and the effects of solder volume and pad extension beyond the edge of component on solder joint shapes were investigated. The resonable design ranges of solder volume and pad extension have been put forward.

Structural Analysis of Platforms with the Effect of Joint Flexibility

A modified space beam element is presented in this paper to consider the local joint flexibility of T, Y tubular joints subjected to axial forces and in-plane bending moments for analysis of platforms. Two numerical examples are shown to verify the efficiency and validity of the method presented here.

Regression Formulations for the Stress at Hot Spot of Multiplanar Tubular DT Joints

Stress concentration analysis of multiplanar tubular DT joints plays an important role in the fatigue design of offshore platforms. A semi-analytic method for stress analysis under the condition of any loads is briefly introduced in the paper. Nineteen multiplanar tubular DT joints with one of two braces of the same dimension subjected to axial loads and out- of- plane bending moments are computed for parametric stress analysis by using the present method. The influence of geometrical parameters on the stresses of multiplanar tubular DT joints is discussed and compared with corresponding uniplanar T joints. The regression formulae for the stress at hot spot of multiplanar DT joints are found by modification of SCF of corresponding uniplanar T joints. The parametric formulae for the maximum stress by superposition. Finally, the influences of stiffening effect and load-interaction effect on the maximum stress of DT joints are discussed.

Seawater Corrosion Fatigue of Welded Joints Under Random Variable Amplitude Loading

Offshore platforms are always subjected to wave action which is random variable amplitude cyclic loading. In order to simulate the stressing condition at the 'hot spot' of the tubular joints and the marine environment, random variable amplitude fatigue tests have been carried out on welded plate joints in sea water. The tests have been conducted under the conditions of loading frequency of 0.2 Hz/, stress ratio of -1, seawater temperature of about 20°C and cathodic protection with the potential about -850 mV, SCE. The test results have been compared with the seawater corrosion fatigue life under constant amplitude loading. Miner's linear cumulative damage summation rule has been used to predict the corrosion fatigue life under variable amplitude loading. The predicted life is in good agreement with the test data.

LDPC Coding Scheme for Improving the Reliability of Multi-Level-Cell NAND Flash Memory in Radiation Environments

Utilizing commercial off-the-shelf(COTS) components in satellites has received much attention due to the low cost. However, commercial memories suffer severe reliability problems in radiation environments. This paper studies the low-density parity-check(LDPC) coding scheme for improving the reliability of multi-level-cell(MLC) NAND Flash memory in radiation environments. Firstly, based on existing physical experiment works, we introduce a new error model for heavyion irradiations; secondly, we explore the optimization of writing voltage allocation to maximize the capacity of the storage channel; thirdly, we design the degree distribution of LDPC codes that is specially suitable for the proposed model; finally, we propose a joint detection-decoding scheme based on LDPC codes, which estimates the storage channel state and executes an adaptive log-likelihood ratio(LLR) calculation to achieve better performance. Simulation results show that, compared with the conventional LDPC coding scheme, the proposed scheme may almost double the lifetime of the MLC NAND Flash memory in radiation environments.

Intensity Evolution of Zonal Shear Line over the Tibetan Plateau in Summer:A Perspective of Divergent and Rotational Kinetic Energies

Based on the ERA5 reanalysis datasets during 1980-2019,a total of eleven zonal shear lines(ZSLs)that caused heavy precipitation and lasted more than 60 hours over the Tibetan Plateau in summer are selected for composite analysis.By decomposing the kinetic energy(K)near the ZSL into divergent and rotational kinetic energies(K_(D)and K_(R))and the kinetic energy of interaction between the divergent wind and the rotational wind(K_(R)D),the influence of the rotational and divergent winds on the evolution of the ZSL intensity is investigated from the perspective of K_(D)and K_(R).The main results are as follows.The ZSL is a comprehensive reflection of rotation and convergence.The intensity evolution of ZSL is essentially synchronized with those of K,K_(R),and K_(RD)but lags behind K_(D)by about three hours.The enhancement of K is mainly contributed by K_(R),which is governed by the conversion from K_(D)to K_(R).Furthermore,the increase in the conversion from K_(D)to K_(R)is controlled by the geostrophic effect term Af,which is determined by the joint enhancement of the zonal rotational and meridional divergent wind components(u_(R)and v_(D)).Therefore,the joint enhancement of u_(R)and v_(D)controls the increase of the ZSL intensity,leading to increased precipitation.