基于CTM和Beam-Column Joint Element的梁柱节点核心区抗剪仿真

为研究基于CTM和Beam-Column Joint Element单元的钢筋混凝土梁柱节点核心区抗震仿真计算,本文先分析了CTM的计算原理和局限性,并对原计算模型进行调整;之后通过试验数据验证了调整前后模型的正确性,并通过参数分析得出调整前后CTM在不同参数下核心区抗剪强度的变化规律;最后通过对比理论计算与试验下核心区抗剪强度变化规律,证明调整后模型更为准确。

A study on the contraction joint element and damage constitutive model for concrete arch dams

A new contraction joint element model for the interface in different meshes between the arch dam sections is con- structed. The study on the elastic-plastic damage constitutive model for concrete, which is applied to multi-axial stresses, is also taken. The models of the dam-foundation-reservoir system for Xingbiling and Jinping concrete arch dams, China are calculated using the proposed contraction joint elements and the elastic-plastic damage constitutive model to verify the proposed models. Results showed that the proposed contraction joint element model has a high precision in simulating the behavior of contraction joints and the elastic-plastic damage constitutive model has a high precision in simulating the behavior of the damage to the concrete.

THREE-DIMENSIONAL FINITE ELEMENT SIMULATION OF TOTAL KNEE JOINT IN GAIT CYCLE

Based on CT scanning pictures from a volunteer＇s knee joint, a three-dimensional finite element model of the healthy human knee joint is constructed including complete femur, tibia, fibular, patellar and the main cartilage and ligaments. This model was validated using experimental and numerical results obtained from other authors. The pressure distribution of contact surfaces of knee joint are calculated and analyzed under the load action of ‘heel strike＇, ‘single limb stance＇ and ‘toe-off＇. The results of the gait cycle are that the contact areas of medial cartilage are larger than that of lateral cartilage; the contact force and contact areas would grow larger with the load increasing; the pressure of lateral meniscus is steady, relative to the significant variation of peak pressure in medial meniscus; and the peak value of contact pressure on all components are usually found at about 4570 of the gait cycle.

Distinct element modelling of fracture plan control in continuum and jointed rock mass in presplitting method of surface mining

Controlled blasting techniques are used to control overbreak and to aid in the stability of the remaining rock formation. Presplitting is one of the most common methods which is used in many open pit mining and surface blast design. The purpose of presplitting is to form a fracture plane across which the radial cracks from the production blast cannot travel. The purpose of this study is to investigate of effect of presplitting on the generation of a smooth wall in continuum and jointed rock mass. The 2D distinct element code was used to simulate the presplitting in a rock slope. The blast load history as a function of time was applied to the inner wall of each blasthole. Important parameters that were considered in the analysis were stress tensor and fracturing pattern. The blast loading magnitude and blasthole spacing and jointing pattern were found to be very significant in the final results.

Sacroiliac joint stability: Finite element analysis of implant number, orientation, and superior implant length

AIM To analyze how various implants placement variables affect sacroiliac(SI) joint range of motion. METHODS An experimentally validated finite element model of the lumbar spine and pelvis was used to simulate a fusion of the SI joint using various placement configurations of triangular implants(iF use Implant System~?). Placement configurations were varied by changing implant orientation, superior implant length, and number of implants. The range of motion of the SI joint was calculated using a constant moment of 10 N-m with a follower load of 400 N. The changes in motion were compared between the treatment groups to assess how the different variables affected the overall motion of the SI joint. RESULTS Transarticular placement of 3 implants with superior implants that end in the middle of the sacrum resulted in the greatest reduction in range of motion(flexion/extension = 73%, lateral bending = 42%, axial rotation = 72%). The range of motions of the SI joints were reduced with use of transarticular orientation(9%-18%) when compared with an inline orientation. The use of a superior implant that ended mid-sacrum resulted in median reductions of(8%-14%) when compared with a superior implant that ended in the middle of the ala. Reducing the number of implants, resulted in increased SI joint range of motions for the 1 and 2 implant models of 29%-133% and 2%-39%, respectively,when compared with the 3 implant model.CONCLUSION Using a validated finite element model we demonstrated that placement of 3 implants across the SI joint using a transarticular orientation with superior implant reaching the sacral midline resulted in the most stable construct. Additional clinical studies may be required to confirm these results.

Static and Dynamic Mechanics Analysis on Artificial Hip Joints with Different Interface Designs by the Finite Element Method

Four different structural models of artificial joints were developed and the finite element method （FEM） was employed to investigate their mechanical characteristics under static and dynamic conditions. The materials used in the FEM calculation were ultra-high molecular weight polyethylene （UHMWPE）, 316L stainless steel, CoCrMo alloy and Ti6A14V alloy. The stress distribution, strain, and elastic deformation under static and dynamic conditions were obtained. Analysis and comparison of the ~alculation results of different models were conducted. It is shown that with the same parameters the model of a metallic femur head covered with an artificial cartilage layer is more similar to the structure of the natural human joint and its mechanical characteristics are the best of the four models.

Finite element analysis of stress and strain distributions in mortise and loose tenon furniture joints

We studied the effect of loose tenon dimensions on stress and strain distributions in T-shaped mortise and loose tenon （M＆amp;LT） furni-ture joints under uniaxial bending loads, and determined the effects of loose tenon length （30, 45, 60, and 90 mm） and loose tenon thickness （6 and 8 mm） on bending moment capacity of M＆amp;LT joints constructed with polyvinyl acetate （PVAc） adhesive. Stress and strain distributions in joint elements were then estimated for each joint using ANSYS finite element （FE） software. The bending moment capacity of joints increased significantly with thickness and length of the tenon. Based on the FE analysis results, under uniaxial bending, the highest shear stress values were obtained in the middle parts of the tenon, while the highest shear elastic strain values were estimated in glue lines between the tenon sur-faces and walls of the mortise. Shear stress and shear elastic strain values in joint elements generally increased with tenon dimensions and corre-sponding bending moment capacities. There was consistency between predicted maximum shear stress values and failure modes of the joints.

Experimental and Finite Element Method Studies of J-Lead Solder Joint Reliability

A comprehensive experimental and numerical study of solder joints for plastic leaded chip carrier (PLCC) 84-Pin, 1.27 mm pitch was carried out. The reliability of solder joints was assessed through accelerated thermal cycling at the temperature range of - 55℃-125℃. The samples were taken out to observe the evolution in microstructure, such as grain coarsening, initiation and propagation of cracks. It was found that the Pb-rich phases segregated gradually and formed a continuous layer adjacent to the intermetallic compound (IMC) layer with increasing the number of thermal cycles, resulting in cracks near the solder/lead interface. The response of stress and strain was studied using nonlinear finite element method (FEM), and the results agreed well with the experimental data.

Mechanical strength analysis of SMT solder joints by finite element method

In this paper,the finite element calculation is applied to the analysis of stress inside the SMT solder joints.The effects of the solder joints'shape,the voids inside them and the quantity of solder on the mechanical strength of the SMT solder joints are analyzed and compared This is essential to the design of the SMT solder joints and soldering techniques.

Finite Element Modeling and Modal Analysis of Complicated Structure with Bolted Joints

A contact bolt model is proposed as a new modeling technique to investigate the complex structure with bolted joints for modal analysis and compared with the coupled bolt model, and the test results are given. Among these models, the coupled bolt model provides the best accurate responses compared with the experimental results. The contact bolt model shows the best effectiveness and usefulness in view of operational time. The bolt models proposed in this study are adopted for a dynamic characteristic analysis of a large diesel engine consisting of several parts which are connected by many bolts. The dynamic behavior of the entire engine structure was investigated by experiment. The coupled bolt model and the contact bolt model were applied to model the assembly of engine with high preload. The experimental results are in good agreement with the finite element method （FEM） results. Compared with the other models, the contact bolt model presented in this paper is more effective and useful in view of operational time and experience of analysts.

Vacuum electron beam brazing technology and finite element analysis on temperature field of capillary to plate joint

Some parts with capillary to plate joint have important application in aerocrafi. Vacuum electron beam brazing （VEBB） technology is used to realize this jointing with capillaries. Firstly 3D finite element analysis model is built in this paper according to this special structure. And then ANSYS finite element analysis software is used to analyze brazing temperature field at different brazing parameters. The calculation results show that the temperature field of simulation has good agreement with that measured by experiment, which proves dependence of the model built in this paper. And also reference parameters could be provided for real brazing process through calculation in this model. Brazed joint of capiUary to plate with good performance is achieved using VEBB technology. The achievement of the study will be applied in aerocrafi in the future.

Finite element simulation for mechanical response of surface mounted solder joints under different temperature cycling

Nonlinear finite element simulation for mechanical response of surface mounted solder joint under different temperature cycling was carried out. Seven sets of parameters were used in order to evaluate the influence of temperature cycling profile parameters. The results show that temperature cycling history has significant effect on the stress response of the solder joint. Based on the concept of relative damage stress proposed by the authors, it is found that enough high temperature holding time is necessary for designing the temperature cycling profile in accelerated thermal fatigue test.

Finite element study on the predicted equivalent stresses in the artificial hip joint

The subsurface fatigue that occurs in the Ultra-High Molecular Weight Polyethylene (UHMWPE) hip joint cup has been identified to be correlated with the contact stress at that cup. This cup stress is known to be affected by the implant design, dimensions and materials. In this study, a 3D finite element modeling has been used to investigate the effects on the cup contact stress when using low stiffness Titanium alloy (Ti) as a femur head. Also, the effects on the cup contact stress due to using different sizes of femur heads, and the presence of metal backing shell with different thicknesses are studied. The finite element results show that the use of low stiffness Ti alloy femur head results in a significant decrease in the cup contact stress compared with Stainless Steel (SS) and Cobalt Chromium (Co Cr Mo) femur heads. The presence of metal backing shell up to 1 mm thickness results in a remarkable decrease in the cup contact stresses especially for small femur heads. Finally, the use of larger femur heads, up to 32 mm diameter, results in significant decrease in the overall predicted hip joint contact. The present results indicate that any changes in design and geometrical parameters of the hip joint have significant consequences in the long term behaviour of the artificial hip joint and should be taken into consideration.

Effects of Traditional Chinese Medicine Five-element Music Combined with Acupoint Application on Perioperative Sleep Quality in Patients Undergoing Joint Replacement Surgery

OBJECTIVE: To explore the effects of traditional Chinese medicine(TCM) five-element music combined with acupoint application on perioperative sleep quality in patients undergoing joint replacement surgery. METHODS: In this study, a total of 122 patients with joint replacement surgery in Beijing Jishuitan Hospital were targeted from 2015 to 2018. All patients were grouped by random number table method. Among them, 61 patients with routine nursing were included in the control group. On this basis, the other 61 patients with acupoint application and TCM five-element music therapy were included as the observation group. 2 weeks later, the Pittsburgh Sleep Quality Index(PSQI) was used to evaluate sleep quality in all patients. The sleep improvement of the 2 groups was evaluated, and the patient was assessed for anxiety and depression, and the curative efficacy was evaluated. RESULTS: After 2 weeks of nursing, the PSQI of the patients improved significantly. The PSQI of the observation group was only 6.6 ± 2.4, and the control group decreased to 9.9 ± 2.7. The observation group was better than the control group, and the difference was statistically significant(P < 0.05). Comparing the 2 groups, the anxiety score of the observation group decreased to 4.8 ± 1.6, which was significantly lower than that of 6.9 ± 2.2 in the control group. The depression score of the observation group decreased to 4.6 ± 1.3, which was significantly lower than that of 6.8 ± 2.3 in the control group. In the control group, the negative emotion scores after nursing were better than those before nursing, and the difference was statistically significant(P < 0.05). Comparing the 2 groups, the effective rate of sleep improvement in the observation group was 96.6%, and the cure rate was as high as 49.1%. The control group was 82.0%, and the cure rate was 18.0%. The observation group was better than the control group, and the difference was statistically significant(P < 0.05). CONCLUSION: The combination of TCM five-element music with acupoint application can improve the perioperative sleep quality of patients undergoing joint replacement surgery, and it can help patients to relieve negative emotions. It is worth promoting.

Finite-Element Analysis of Parts Stress State of Tight Joint Assembled by Press Fitting

This paper includes descriptions of the stress distribution regularities in the tight joint parts, regularities of the stress state changes in the contact region along coupling length, stress concentration factors, levels of additional stresses caused by press fitting. Distributions of stress intensity, axial stress, contact pressure, tangent stress in parts and in contact zone along coupling length are considered. Calculation results obtained by three approaches: Lame relationships, FEM without considering assembly method, FEM with considering press fitting process are analyzed and compared. The adequacy of research carried out is confirmed.

Nonlinear Finite Element Analysis and Optimum Design of Spot-Welded Joints and Weld-Bonded Joints

Resistance spot welding and hybrid weld bonding have wide applications in the body work construction within the automobile industry. The integrity of the spot welds and applied adhesives determines the body assembly rigidity and dynamic performance. Incorporating contact nonlinearity and geometric nonlinearity, finite element analysis (FEA) have been carried out to investigate the structural stiffness and strength of both spot-welded and weld-bonded assemblies. Topology optimization has been performed to reveal the distributions of material effectiveness in the overlap regions and suggest a feasible method for removing underutilized material for weight reduction. Design optimization has been conducted with an aim to reduce the maximum von Mises stress in the assembly to minimum by choosing optimum values for a set of design variables, including the weld spacing, weld diameter and overlap width.

有限元分析不同程度冈上肌断裂对肩关节应力的影响

背景:目前研究冈上肌的精细解剖及各亚区域的生物力学表现的实验较多,但是对冈上肌不同区域的损伤所带来的肩关节应力的影响鲜有耳闻。很有必要了解不同区域的冈上肌损伤对关节软骨及关节盂的应力大小及分布的影响,从而给临床诊治提供一些理论支持。目的:探究在三维有限元软件中模拟不同程度的冈上肌断裂对肱骨软骨面、关节盂唇及关节盂软骨关节面的最大应力值。方法:获取正常健康的肩关节CT或MRI导入Mimics、Geomagic进行提取模型,再通过Soildworks对模型构建,再对各个模型的冈上肌进行不同程度的损伤,模拟出不同区域的断裂。最后导入机械软件Ansys,进行三维有限元生物力学分析,计算肱骨软骨面、关节盂唇及关节盂软骨关节面的应力数值。结果与结论:①随着冈上肌损伤程度的加重肩关节软骨面及盂唇的应力也会增加;②冈上肌前部在各区域中最为重要;③不同程度的冈上肌断裂对肩关节盂唇面的软骨应力大小有影响,而应力的分布区域无明显改变;④提示肩关节水平外展起始时,前部发挥着重要的作用,其次为后部深区;当冈上肌前部损伤时肩关节软组织应力增加明显,还容易引起关节盂唇顶部及关节盂软骨前下方的损伤。

Numerical Computation of Stress Intensity Factors for Bolt-hole Corner Crack in Mechanical Joints

The three-dimensional finite element method is used to solve the problem of the quarter-elliptical comer crack of the bolt-hole in mechanical joints being subjected to remote tension. The square-root stress singularity around the corner crack front is simulated using the collapsed 20-node quarter point singular elements. The contact interaction between the bolt and the hole boundary is considered in the finite element analysis. The stress intensity factors （SIFs） along the crack front are evaluated by using the displacement correlation technique. The effects of the amount of clearance between the hole and the bolt on the SIFs are investigated. The numerical results indicate that the SIF for mode I decrease with the decreases in clearance, and in the cases of clearance being present, the corner crack is in a mix-mode, even if mode I loading is dominant.

有限元分析技术在膝关节生物力学应用中的特点与优势

背景:有限元分析是一种先进的计算机工程技术,利用数学近似的方法对真实人体进行模拟,可以真实反映膝关节结构内部的生物力学特征,为理解膝关节疾病发病机制、优化手术方案以及开发新型植入材料提供了有效的工具。目的:对膝关节有限元模型的建立及其在膝关节疾病研究中的应用进行综述,并展望了未来的发展趋势。方法:第一作者于2024年4月以“Finite Element Analysis,FEA,knee joint,Finite Element Model,Knee Biomechanics,Knee Osteoarthritis,Knee Prosthesis,Knee Ligaments,Meniscus”为英文检索词在PubMed和EI数据库进行检索,以“有限元分析,有限元模型,膝关节,生物力学,骨关节炎,计算模型,膝关节假体,膝关节韧带,半月板”为中文检索词在中国知网和万方数据库进行检索,最终纳入75篇文献进行分析。结果与结论:①有限元分析法利用医学影像数据获得三维人体模型,将复杂的人体关节结构简化为有限且相互连接的单元,通过对模型施加外部载荷,直观地显示膝关节内部的应力分布。②研究者通过有限元分析深入研究膝关节在不同工况下的内部应力和应变分布,可发现膝关节内部载荷分配平衡改变时,关节软骨的过度载荷及部分区域的负荷下降,这种长期异常应力会引起软骨变形和磨损,最终缺失,对于理解生物力学因素如何引起膝关节退行性变至关重要。③有研究通过有限元分析评估膝骨关节炎患者采用太极拳、步态调整等物理治疗方法的效果,结果显示这些治疗方法减少了软骨的过度负荷,为临床治疗提供了科学理论依据。④临床医生通过有限元分析在手术前进行三维重建、数据测量和模拟手术,能够优化手术治疗策略;此外,还可以通过模拟不同假体的力学特征,改进假体的形状、材料和固定方式,减少患者的并发症,提高患者的治疗效果。⑤人工智能与有限元分析相结合使得有限元模型的构建更为精确和易于操作,极大提高了临床医生医疗实践的效率和患者的治疗效果。⑥有限元分析仅是数字化的模拟,与真实物理状态仍存在一定差异。

A FRACTURE-ENERGY-BASED ELASTO-SOFTENING-PLASTIC CONSTITUTIVE MODEL FOR JOINTS OF GEOMATERIALS

On the basis of plasticity and fracture mechanics for quasi-brittle materials, this article presented a constitutive model for gradual softening behavior of joints of geomaterials. Corresponding numerical tests are carried out at the local level. Characteristics of the model proposed are 1) plastic softening and dilatancy behavior are directly related to the fracture process of joint, and much less material and model parameters are required compared with those proposed by references; 2) the process of decohesion coupled with frictional sliding at both micro-scale and macro-scale is described.