The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of...The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of CJRM is important for engineering construction.The Voronoi diagram and three-dimensional printing technology were used to make an irregular columnar jointed mold,and the irregular CJRM(ICJRM)specimens with different dip directions and dip angles were prepared.Uniaxial compression tests were performed,and the anisotropic strength and deformation characteristics of ICJRM were described.The failure modes and mechanisms were revealed in accordance with the final appearances of the ICJRM specimens.Based on the model test results,the empirical correlations for determining the field deformation and strength parameters of CJRM were derived using the dip angle and modified joint factor.The proposed empirical equations were used in the Baihetan Project,and the calculated mechanical parameters were compared with the field test results and those obtained from the tunneling quality index method.Results showed that the deformation parameters determined by the two proposed methods are all consistent with the field test results,and these two methods can also estimate the strength parameters effectively.展开更多
Balia Nala is the outlet of the Nainital lake, flowing towards southeast direction. Presence of Nainital habitation at its right bank has high socio-economic importance. This study presents the stability analysis of a...Balia Nala is the outlet of the Nainital lake, flowing towards southeast direction. Presence of Nainital habitation at its right bank has high socio-economic importance. This study presents the stability analysis of a ravine/valley along Balia Nala. Variegated slates(lower Krol and upper Blaini formations) are the main rock types, wherever the outcrop does exist and rest of the area is covered by slope wash and river borne materials. Three sets of joints are presented in the area, but 4 sets of joints also exist at some locations. Nainital lake fault intersected by Manora fault from southwest direction passes through eastern side of the study area, and some small faults, which are sub-branches of Nainital lake fault, are observed(with 10 m offset) and promote the landslide in the area. This study shows that different kinds of discontinuities(joints, faults and shear zones) and rapid down cutting by the stream due to neotectonic activity affect the stability of the slope. The fragile lithology and deep V-shaped valley further accelerate the mass movement in the study area. In addition, rock mass rating(RMR), factor of safety(FOS) and graphical analysis of the joints indicate the study area as landslide-prone zone. This study will be helpful in not only reducing the risk on life of people, but also in assisting the ongoing civil work in the study area.展开更多
This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock sl...This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock slopes with different joint configurations. The stress in each rock block is not homogeneous and blocks rotate in failure development. Failure modes depend on the configuration of joints. Toppling failure is observed for the slope with straight joints and sliding failure is observed for the slope with staged joints. The DEM results are also compared with those of limit equilibrium method (LEM). Without considering the joints in rock masses, the LEM predicts much higher factor of safety than physical modeling and DEM. The failure mode and factor of safety predicted by the DEM are in good agreement with laboratory tests for any jointed rock slope.展开更多
基金This work was supported by the Fundamental Research Funds for the Central Universities,the Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX21_0487)the National Natural Science Foundation of China(Grant Nos.41831278,and 51579081).
文摘The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of CJRM is important for engineering construction.The Voronoi diagram and three-dimensional printing technology were used to make an irregular columnar jointed mold,and the irregular CJRM(ICJRM)specimens with different dip directions and dip angles were prepared.Uniaxial compression tests were performed,and the anisotropic strength and deformation characteristics of ICJRM were described.The failure modes and mechanisms were revealed in accordance with the final appearances of the ICJRM specimens.Based on the model test results,the empirical correlations for determining the field deformation and strength parameters of CJRM were derived using the dip angle and modified joint factor.The proposed empirical equations were used in the Baihetan Project,and the calculated mechanical parameters were compared with the field test results and those obtained from the tunneling quality index method.Results showed that the deformation parameters determined by the two proposed methods are all consistent with the field test results,and these two methods can also estimate the strength parameters effectively.
文摘Balia Nala is the outlet of the Nainital lake, flowing towards southeast direction. Presence of Nainital habitation at its right bank has high socio-economic importance. This study presents the stability analysis of a ravine/valley along Balia Nala. Variegated slates(lower Krol and upper Blaini formations) are the main rock types, wherever the outcrop does exist and rest of the area is covered by slope wash and river borne materials. Three sets of joints are presented in the area, but 4 sets of joints also exist at some locations. Nainital lake fault intersected by Manora fault from southwest direction passes through eastern side of the study area, and some small faults, which are sub-branches of Nainital lake fault, are observed(with 10 m offset) and promote the landslide in the area. This study shows that different kinds of discontinuities(joints, faults and shear zones) and rapid down cutting by the stream due to neotectonic activity affect the stability of the slope. The fragile lithology and deep V-shaped valley further accelerate the mass movement in the study area. In addition, rock mass rating(RMR), factor of safety(FOS) and graphical analysis of the joints indicate the study area as landslide-prone zone. This study will be helpful in not only reducing the risk on life of people, but also in assisting the ongoing civil work in the study area.
文摘This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock slopes with different joint configurations. The stress in each rock block is not homogeneous and blocks rotate in failure development. Failure modes depend on the configuration of joints. Toppling failure is observed for the slope with straight joints and sliding failure is observed for the slope with staged joints. The DEM results are also compared with those of limit equilibrium method (LEM). Without considering the joints in rock masses, the LEM predicts much higher factor of safety than physical modeling and DEM. The failure mode and factor of safety predicted by the DEM are in good agreement with laboratory tests for any jointed rock slope.
