Distinct element modelling of fracture plan control in continuum and jointed rock mass in presplitting method of surface mining

Controlled blasting techniques are used to control overbreak and to aid in the stability of the remaining rock formation. Presplitting is one of the most common methods which is used in many open pit mining and surface blast design. The purpose of presplitting is to form a fracture plane across which the radial cracks from the production blast cannot travel. The purpose of this study is to investigate of effect of presplitting on the generation of a smooth wall in continuum and jointed rock mass. The 2D distinct element code was used to simulate the presplitting in a rock slope. The blast load history as a function of time was applied to the inner wall of each blasthole. Important parameters that were considered in the analysis were stress tensor and fracturing pattern. The blast loading magnitude and blasthole spacing and jointing pattern were found to be very significant in the final results.

Finite element analysis of stress and strain distributions in mortise and loose tenon furniture joints

We studied the effect of loose tenon dimensions on stress and strain distributions in T-shaped mortise and loose tenon （M＆amp;LT） furni-ture joints under uniaxial bending loads, and determined the effects of loose tenon length （30, 45, 60, and 90 mm） and loose tenon thickness （6 and 8 mm） on bending moment capacity of M＆amp;LT joints constructed with polyvinyl acetate （PVAc） adhesive. Stress and strain distributions in joint elements were then estimated for each joint using ANSYS finite element （FE） software. The bending moment capacity of joints increased significantly with thickness and length of the tenon. Based on the FE analysis results, under uniaxial bending, the highest shear stress values were obtained in the middle parts of the tenon, while the highest shear elastic strain values were estimated in glue lines between the tenon sur-faces and walls of the mortise. Shear stress and shear elastic strain values in joint elements generally increased with tenon dimensions and corre-sponding bending moment capacities. There was consistency between predicted maximum shear stress values and failure modes of the joints.

Mechanical strength analysis of SMT solder joints by finite element method

In this paper,the finite element calculation is applied to the analysis of stress inside the SMT solder joints.The effects of the solder joints'shape,the voids inside them and the quantity of solder on the mechanical strength of the SMT solder joints are analyzed and compared This is essential to the design of the SMT solder joints and soldering techniques.

A FRACTURE-ENERGY-BASED ELASTO-SOFTENING-PLASTIC CONSTITUTIVE MODEL FOR JOINTS OF GEOMATERIALS

On the basis of plasticity and fracture mechanics for quasi-brittle materials, this article presented a constitutive model for gradual softening behavior of joints of geomaterials. Corresponding numerical tests are carried out at the local level. Characteristics of the model proposed are 1) plastic softening and dilatancy behavior are directly related to the fracture process of joint, and much less material and model parameters are required compared with those proposed by references; 2) the process of decohesion coupled with frictional sliding at both micro-scale and macro-scale is described.

Dynamic Analysis of Historical Brick Masonry House

Brick masonry constructions are very common in many areas in the world and their failure in earthquakes has been the cause of many deaths. Since human safety is main issue of disaster management, people are more concerned about the structural assessment and strengthening of those constructions. One historical brick masonry house located in Kathmandu world heritage site is modeled by FEM （finite element method） and analyzed in E1 Centro earthquake ground motions. Bricks are modeled as solid elements and the interfaces between the brick units are modeled as zero thickness joint elements. Then, non-linear analyses of the house are applied satisfying the famous Mohr-Coulomb failure criterion. The result shows that the house is very weak and sustains large deformation in El Centro 1940 Earthquake. A strengthening solution modifying the connections of existing elements and adding wooden frame inside the house can reduce the deformations significantly.

An Average Failure Index Method for the Tensile Strength Prediction of Composite Adhesive-bonded π Joints

An average failure index method based on accurate FEA was proposed for the tensile strength prediction of composite out-of-plane adhesive-bonded π joints. Based on the simple and independent maximum stress failure criterion, the failure index was introduced to characterize the degree of stress components close to their corresponding material strength. With a brief load transfer analysis, the weak fillers were prominent and further detailed discussion was performed. The maximum value among the average failure indices which were related with different stress components was filtrated to represent the failure strength of the critical surface, which is either the two curved upside surfaces or the bottom plane of the fillers for composite π joints. The tensile strength of three kinds of π joints with different material systems, configurations and lay-ups was predicted by the proposed method and corresponding experiments were conducted. Good agreements between the numerical and experimental results give evidence of the effectiveness of the proposed method. In contrast to the existed time-consuming strength prediction methods, the proposed method provides a capability of quickly assessing the failure of complex out-of-plane joints and is easy and convenient to be widely utilized in engineering.

A study on the contraction joint element and damage constitutive model for concrete arch dams

A new contraction joint element model for the interface in different meshes between the arch dam sections is con- structed. The study on the elastic-plastic damage constitutive model for concrete, which is applied to multi-axial stresses, is also taken. The models of the dam-foundation-reservoir system for Xingbiling and Jinping concrete arch dams, China are calculated using the proposed contraction joint elements and the elastic-plastic damage constitutive model to verify the proposed models. Results showed that the proposed contraction joint element model has a high precision in simulating the behavior of contraction joints and the elastic-plastic damage constitutive model has a high precision in simulating the behavior of the damage to the concrete.