浮动基多机协调吊运系统的工作空间分析

At present,the cranes used at sea have several shortcomings in terms of flexibility,efficiency,and safety.Therefore,a floating multi-robot coordinated lifting system is proposed to fulfill the offshore lifting requirements.First,the structure of the lifting system is established according to the lifting task,the kinematic model of the system is developed by using the D–H coordinate transformation,and the dynamic model is developed based on rigid-body dynamics and hydrodynamics.Then,the static and dynamic workspace of the lifting system are analyzed,and the solving steps of the workspace are given by using the Monte–Carlo method.The effect of the load mass and the maximum allowable tension of the cable on the workspace is examined by simulation.Results show that the lifting system has limited carrying capacity and a data reference for selecting the structural parameters by analyzing the factors affecting the workspace.Findings provide a basis for further research on the optimal design of structural parameters and the determination of safe configurations of the lifting system.

Kinematic-mapping-model-guided analysis and optimization of 2-PSS&1-RR circular-rail parallel mechanism for fully steerable phased array antennas

This paper presents a systematic methodology for analyzing and optimizing an innovative antenna mount designed for phased array antennas, implemented through a novel 2-PSS&1-RR circular-rail parallel mechanism. Initially, a comparative motion analysis between the 3D model of the mount and its full-scale prototype is conducted to validate effectiveness. Given the inherent complexity, a kinematic mapping model is established between the mount and the crank-slider linkage, providing a guiding framework for subsequent analysis and optimization. Guided by this model, feasible inverse and forward solutions are derived, enabling precise identification of stiffness singularities. The concept of singularity distance is thus introduced to reflect the structural stiffness of the mount. Subsequently, also guided by the mapping model, a heuristic algorithm incorporating two backtracking procedures is developed to reduce the mount's mass. Additionally, a parametric finite-element model is employed to explore the relation between singularity distance and structural stiffness. The results indicate a significant reduction(about 16%) in the antenna mount's mass through the developed algorithm, while highlighting the singularity distance as an effective stiffness indicator for this type of antenna mount.

Vehicle kinematics modeling and design of vehicle trajectory generator system

A trajectory generator based on vehicle kinematics model was presented and an integrated navigation simulation system was designed.Considering that the tight relation between vehicle motion and topography,a new trajectory generator for vehicle was proposed for more actual simulation.Firstly,a vehicle kinematics model was built based on conversion of attitude vector in different coordinate systems.Then,the principle of common trajectory generators was analyzed.Besides,combining the vehicle kinematics model with the principle of dead reckoning,a new vehicle trajectory generator was presented,which can provide process parameters of carrier anytime and achieve simulation of typical actions of running vehicle.Moreover,IMU(inertial measurement unit) elements were simulated,including accelerometer and gyroscope.After setting up the simulation conditions,the integrated navigation simulation system was verified by final performance test.The result proves the validity and flexibility of this design.

Anomaly detection method based on kinematics model and nonholonomic constraint of vehicle

A method used to detect anomaly and estimate the state of vehicle in driving was proposed.The kinematics model of the vehicle was constructed and nonholonomic constraint conditions were added,which refer to that once the vehicle encounters the faults that could not be controlled,the constraint conditions are violated.Estimation equations of the velocity errors of the vehicle were given out to estimate the velocity errors of side and forward.So the stability of the whole vehicle could be judged by the velocity errors of the vehicle.Conclusions were validated through the vehicle experiment.This method is based on GPS/INS integrated navigation system,and can provide foundation for fault detections in unmanned autonomous vehicles.

Parameter Identification and Application of Slippage Kinematics for Tracked Mobile Robots

A new parameter identification method is proposed to solve the slippage problem when tracked mobile robots execute turning motions.Such motion is divided into two states in this paper:pivot turning and coupled turning between angular velocity and linear velocity.In the processing of pivot turning,the slippage parameters could be obtained by measuring the end point in a square path.In the process of coupled turning,the slippage parameters could be calculated by measuring the perimeter of a circular path and the linear distance between the start and end points.The identification results showed that slippage parameters were affected by velocity.Therefore,a fuzzy rule base was established with the basis on the identification data,and a fuzzy controller was applied to motion control and dead reckoning.This method effectively compensated for errors resulting in unequal tension between the left and right tracks,structural dimensions and slippage.The results demonstrated that the accuracy of robot positioning and control could be substantially improved on a rigid floor.

Kinematics modeling of a 6-PSS parallel mechanism with wide-range flexure hinges

A novel 6-PSS flexible parallel mechanism was presented,which employed wide-range flexure hinges as passive joints.The proposed mechanism features micron level positioning accuracy over cubic centimeter scale workspace.A three-layer back-propagation(BP) neural network was utilized to the kinematics analysis,in which learning samples containing 1 280 groups of data based on stiffness-matrix method were used to train the BP model.The kinematics performance was accurately calculated by using the constructed BP model with 19 hidden nodes.Compared with the stiffness model,the simulation and numerical results validate that BP model can achieve millisecond level computation time and micron level calculation accuracy.The concept and approach outlined can be extended to a variety of applications.

Three-Dimensional Kinematics Simulation of Robot Fighting Platform in Virtual Environment

A method of 3 D kinematics simulation of robot fighting platform （RFP） in virtual environment is proposed with the aim of enhancing vision telepresence. Based on the theory of space coordinate transformation, kinematics equat!ons of RFP are formulated; followed by applying a method of modeling using 3DMAX software to build an RFP＇s 3D geometric model before a 3D kinematics simulation system of RFP is completed based on virtual reality technology and Open Inventor VC ＋ ＋. Test results have indicated that this system can perform RFP＇s kinematics simulation in virtual environment. It can also imitate RFP＇s motion states and environmental features well. Moreover, not only can better real-time performances and interactions be achieved but also operator＇s vision telepresence be enhanced, therefore this approach may help lay the foundation for the realization of RFP＇s teleoperation with vision telepresence.

Recent Study of Drag Embedment Plate Anchors in China

Experimental and theoretical studies of drag embedment plate anchors recently carried out in Tianjin University are summarized in this research paper, which involve a series of important topics relevant to the study of drag anchors. The techniques for measuring the trajectory and movement direction of drag anchors in soils, the techniques for measuring the moving embedment point and reverse eatenary shape of the embedded drag line, the penetration mechanism and kinematic behavior of drag anchors, the ultimate embedment depth of drag anchors, the movement direction of the anchor with an arbitrary fluke section, the reverse catenary properties of the embedded drag line, the interaetional properties between drag anchor and installation line, the kinematic model of drag anchors in seabed soils, and the analytical method for predicting the anchor trajectory in soils will all be examined. The present work remarkably reduces the uncertainties in design and analysis of drag embedment plate anchors, and is beneficial to improving the application of this new type of drag anchor in offshore engineering.

Improved Stiffness Modeling for An Exechon‑Like Parallel Kinematic Machine(PKM)and Its Application

Hole drilling or contour milling for the large and complex workpieces such as automobile panels and aircraft fuselages makes a high combined demand on machining accuracy,stiffness and workspace of machining equipment.Therefore,a 5-DOF(degrees of freedom)parallel kinematic machine(PKM)with redundant constraints is proposed.Based on the kinematics analysis of the parallel mechanism using intermediate variables,the kinematics problems of the PKM are solved through equivalent kinematics model.The structural stiffness matrix method is adopted to model the stiffness of the parallel mechanism of the PKM,where the stiffness of each joint and branch component is obtained by stiffness formula and finite element analysis.And the stiffness model of the parallel mechanism is improved by correction coefficient matrix,each element of which is constructed as a polynomial function of three independent end variables of the parallel mechanism.The terminal stiffness matrices obtained by simulation result are used to determine the coefficients of polynomial function by least square fitting to describe the correction coefficient over the workspace of the parallel mechanism quantitatively.The experiment results prove that the modification method can greatly improve the stiffness model of the parallel mechanism.To enhance the machining accuracy of the PKM,the proposed kinematics model and the improved stiffness model are utilized to optimize the working stiffness of parallel machine by searching the best relative position of parallel machine and workpiece.A plate workpiece taken as example is examined in the case study section,which demonstrates the effectiveness of optimization method.

Modeling and simulation of a mini AUV in spatial motion

Accurate modeling and simulation of autonomous underwater vehicle （AUV） is essential for autonomous control and maneuverability research. In this paper, a mini AUV- ＂MAUV-Ⅱ＂ was researched and the nonlinear mathematic model of the AUV in spatial motion was derived based on momentum theorem. The forces acting on AUV were resolved to several modules which were expressed in matrix form. Based on the motion model and combined with virtual reality technology, a motion simulation system was constructed. Considering the characteristic of ＂MAUV-Ⅱ ＂, the heading control and depth control were simulated by adopting S-surface control method. A long distance traveling simulation experiment based on target planning was also done. The simulation results show that the ＂MAUV-Ⅱ＂ has good spatial maneuverability, and verify the feasibility and reliability of control software.

Study on Dynamic Characteristics of Hydraulic Pumping Unit on Offshore Platform

A new technology of offshore oil rod pumping production is developed for offshore heavy oil recovery. A new type of miniature hydraulic pumping unit with long-stroke, low pumping speed and compact structure is designed based on the spatial characteristics of offshore platforms. By combining the strengths of sinusoidal velocity curve and trapezoidal velocity curve, a kinematical model of the acceleration, the velocity and displacement of the pumping unit＇s hanging point is established. The results show that the pumping unit has good kinematic characteristics of smooth motion and small dynamic load. The multi-degree-of-freedom dynamic model of the single-well pumping unit is established. The first and second order natural frequencies of the sucker rod string subsystem and the pumping unit subsystem are studied. The results show that the first and the second order natural frequencies among the pumping rod string, pumping unit-platform subsystem and the dynamic excitation have differences over 5 times from each other, indicating that resonance phenomenon will not appear during the operation and the dynamic requirements for field use are met in the system.

Algebraic Method‑Based Point‑to‑Point Trajectory Planning of an Under‑Constrained Cable‑Suspended Parallel Robot with Variable Angle and Height Cable Mast

To avoid impacts and vibrations during the processes of acceleration and deceleration while possessing flexible working ways for cable-suspended parallel robots(CSPRs),point-to-point trajectory planning demands an under-constrained cable-suspended parallel robot(UCPR)with variable angle and height cable mast as described in this paper.The end-effector of the UCPR with three cables can achieve three translational degrees of freedom(DOFs).The inverse kinematic and dynamic modeling of the UCPR considering the angle and height of cable mast are completed.The motion trajectory of the end-effector comprising six segments is given.The connection points of the trajectory segments(except for point P3 in the X direction)are devised to have zero instantaneous velocities,which ensure that the acceleration has continuity and the planned acceleration curve achieves smooth transition.The trajectory is respectively planned using three algebraic methods,including fifth degree polynomial,cycloid trajectory,and double-S velocity curve.The results indicate that the trajectory planned by fifth degree polynomial method is much closer to the given trajectory of the end-effector.Numerical simulation and experiments are accomplished for the given trajectory based on fifth degree polynomial planning.At the points where the velocity suddenly changes,the length and tension variation curves of the planned and unplanned three cables are compared and analyzed.The OptiTrack motion capture system is adopted to track the end-effector of the UCPR during the experiment.The effectiveness and feasibility of fifth degree polynomial planning are validated.

Dynamic Modeling and Investigation of Maneuver Characteristics of A Deep-Sea Manned Submarine Vehicle

A deep-sea Manned Submarine Vehicle （MSV） is usually required to move at a low forward speed and a low rotational speed when it executes investigation tasks. In this condition, the motion is in large drift angles, and the maneuverability hydrodynamic forces cannot be expressed properly in the conventional mathematical model of submersible motion. In this paper, firstly, a general equation of MSV with six-freedom motion is presented, and the numerical simulation of descent/ascent motion and helix motion is conducted to reveal the general maneuver characteristics of MSV. Secondly, according to the data of captive model tests of large drift angles of MSV, the regression analysis of position hydrodynamic forces and rotation hydrodynamic forces is carried out, and the results of regression analysis of maneuverability hydrody- namic characteristics are analyzed to reveal the special maneuver characteristics. Thirdly, a special new mathematical model of MSV with the whole range of drift angles motion is presented, which can be used to predict hydrodynamic performance of motion in the 0° - 180° range of drift angles. The results are applied to the design of maneuverability hydrodynamic forces, development of control system and simulator of a practical MSV.

Analysis on structural characteristics of rotors in twin-rotor cylinder-embedded piston engine

Twin-rotor cylinder-embedded piston engine is proposed for dealing with the sealing problems of rotors in twin-rotor piston engine where the existent mature sealing technologies for traditional reciprocating engine can be applied.The quantity and forms of its sealing surfaces are reduced and simplified,and what's more,the advantages of twin-rotor piston engine are inherited,such as high power density and no valve mechanism.Given the motion law of two rotors,its kinematic model is established,and the general expression for some parameters related to engine performance,such as the trajectory,displacement,velocity and acceleration of the piston and centroid trajectory,angular displacement,velocity and acceleration of the rod are presented.By selecting different variation patterns of relative angle of two rotors,the relevant variables are compared.It can be concluded that by designing the relative angle function of two rotors,the volume variation of working chamber can be changed.However,a comprehensive consideration for friction and vibration is necessary because velocity and acceleration are quite different in the different functions,the swing magnitude of rod is proportional to link ratio λ,and the position of rod swing center is controlled by eccentricity e.In order to reduce the lateral force,a smaller value of λ should be selected in the case of the structure,and the value of e should be near 0.95.There is no relationship between the piston stroke and the variation process of relative angle of two rotors,the former is only proportional to the amplitude of relative angle of two rotors.

Accurate parameter estimation of systematic odometry errors for two-wheel differential mobile robots

Odometry using incremental wheel encoder odometry suffers from the accumulation of kinematic sensors provides the relative robot pose estimation. However, the modeling errors of wheels as the robot＇s travel distance increases. Therefore, the systematic errors need to be calibrated. The University of Michigan Benchmark（UMBmark） method is a widely used calibration scheme of the systematic errors in two wheel differential mobile robots. In this paper, the accurate parameter estimation of systematic errors is proposed by extending the conventional method. The contributions of this paper can be summarized as two issues. The first contribution is to present new calibration equations that reduce the systematic odometry errors. The new equations were derived to overcome the limitation of conventional schemes. The second contribu tion is to propose the design guideline of the test track for calibration experiments. The calibration performance can be im proved by appropriate design of the test track. The simulations and experimental results show that the accurate parameter es timation can be implemented by the proposed method.

A Kinematic Thermal Model for Descending Slabs with Velocity Boundary Layers:A Case Study for the Tonga Subducting Slab

For the purpose of investigating the influence of metastable olivine（MO） phase transformations on both deep seismicity and stagnation of slabs,we constructed a 2-dimensional finite element thermal model for a 120 Ma-old 50°dipping oceanic lithosphere descending at 10 cm/yr with velocity boundary layers,which would mitigate the interference of constant velocity field for the slab. The resulting temperatures show that most of intermediate and deep earthquakes occurring within the Tonga slab are occurring inside the 800℃and 1200℃isotherm,respectively.The elevation of olivine transformation near～410 km and respective persistence of metastable olivine and spinel within the transition zone and beneath 660 km would thus result in bimodal positive,zonal,negative density anomalies,respectively.These results together with the resulting pressure anomalies may reflect the stress pattern of the Tonga slab：（i） slab pull force exerts above a depth of～230 km;（ii） MO existence changes the buoyancy force within the transition zone and facilitates slab stagnation at a depth of 660 km;（iii） as the subducting materials accumulated over 660 km,deepest earthquakes occur due to MO transformation;（iv） a flattened‘slab’ may penetrate into the lower mantle due to the density increment of Sp transformation.

Practical approach to determining traffic congestion propagation boundary due to traffic incidents

A practical approach for predicting the congestion boundary due to traffic incidents was proposed. Based on the kinematic wave theory and Van Aerde single-regime flow model, a model for estimating the congestion propagation speed for the basic road segment was developed. Historical traffic flow data were used to analyze the time variant characteristics of the urban traffic flow for each road type. Then, the saturation flow rate was used for analyzing the impact of the traffic incident on the traversing traffic flow at the congestion area. The base congestion propagation speed for each road type was calculated based on field data, which were provided by the remote traffic microwave sensors(RTMS), floating car data(FCD) system and screen line survey. According to a comparative analysis of the congestion propagation speed, it is found that the expressway, major arterial, minor arterial and collector are decreasingly influenced by the traffic incident. Subsequently, the impact of turning movements at intersections on the congestion propagation was considered. The turning ratio was adopted to represent the impact of turning movements, and afterward the corresponding propagation pattern at intersections was analyzed. Finally, an implementation system was designed on a geographic information system(GIS) platform to display the characteristics of the congestion propagation over the network. The validation results show that the proposed approach is able to capture the congestion propagation properties in the actual road network.

Ground-motion simulation for the MW6.1 Ludian earthquake on 3 August 2014 using the stochastic finite-fault method

The stochastic finite-fault simulation method was applied to synthesize the horizontal ground acceleration seismograms produced by the MW6.1 Ludian earthquake on August 3,2014.For this purpose,we produced first a total of 200 kinematic source models for the Ludian event,which are characterized by the heterogeneous slip on the conjugated ruptured fault and the slip-dependent spreading of the rupture front.The results indicated that the heterogeneous slip and the spatial extent of the ruptured fault play dominant roles in the spatial distribution of ground motions in the near-fault area.The peak ground accelerations(PGAs)and 5%-damped pseudospectral accelerations(PSAs)at periods shorter than 0.5 s estimated on the resulting synthetics generally match well with the observations at stations with Joyner-Boore distances(RJB)greater than 20 km.The synthetic PGVs and PSAs at periods of 0.5 s and 0.75 s are in good agreement with predicted medians by the Yu14 model(Yu et al.,2014).However,the synthetic results are generally much lower than the predicted medians by BSSA14 model(Boore et al.,2014).Moreover,the ground motion variability caused by the randomness in the source rupture process was evaluated by these synthetics.The standard deviations of PSAs on the base-10 logarithmic scale,Sigma[log10(PSA)],are closely dependent on either the spectral period or the RJB.The Sigma[log10(PSA)]remains a constant approximately 0.55 at periods shorter than 0.1 s,and then increase continuously up to^0.13 as the period increases from 0.1 to 2.0 s.The Sigma[log10(PSA)]values at periods of 0.1‒2.0 s show the downward tendency as the RJB values increase.However,the Sigma[log10(PSA)]​values at periods shorter than 0.1 s decrease as the RJB values increase up to^50 km,and then increase with the increasing RJB.Furthermore,we found that the ground-motion variability shows the significant dependence on the azimuth.

Preliminary results on kinematic model of tectonic blocks derived from high precision GPS observations in Southwest China

In the paper, the kinematic model of tectonic blocks in southwest China is studied based on the precision GPS observations carried out under the major subject of 'Studies on Current Crustal Movement and Geodynamics' which belongs to the State Climbing Project. It is believed that at present, the data of high precision GPS observation may provide convincing information related to the horizontal movement of tectonic blocks in the Chinese mainland. The preliminary results obtained from the kinematic model have given some direct evidences for the research of dynamic mechanism of crustal deformation in the Chinese mainland and on the basis of which, the kinematic characteristics and their relations to the seismicity and seismic risk in the reobserved region are analysed. The preliminary observation results are encouraging.

Magnetostrictive and Kinematic Model Considering the Dynamic Hysteresis and Energy Loss for GMA

Due to the influence of magnetic hysteresis and energy loss inherent in giant magnetostrictive materials （GMM）, output displacement accuracy of giant magnetostrictive actuator （GMA） can not meet the precision and ultra precision machining. Using a GMM rod as the core driving element, a GMA which may be used in the field of precision and ultra precision drive engineering is designed through modular design method. Based on the Armstrong theory and elastic Gibbs free energy theory, a nonlinear magnetostriction model which considers magnetic hysteresis and energy loss characteristics is established. Moreover, the mechanical system differential equation model for GMA is established by utilizing D＇Alembert＇s principle. Experimental results show that the model can preferably predict magnetization property, magnetic potential orientation, energy loss for GMM. It is also able to describe magnetostrictive elongation and output displacement of GMA. Research results will provide a theoretical basis for solving the dynamic magnetic hysteresis, energy loss and working precision for GMA fundamentally.