Threshold Photoelectron-photoion Coincidence Imaging of Dissociation Dynamic of NO＋ at c3∏（v′=0） State

The photodissociation of NO＋ at c3∏（v′=0） state is studied by threshold photoelectron- photoion coincidence imaging method. By some assumptions, the relations between velocity in center of mass （CM） coordinates and most probable center of mass （MPCM） coordinates, time of flight and displacement in the velocity map image of fragment ions are derived using vector addition of velocity and displacement on the condition of perpendicular molecular beam. Using these relations the velocity in CM coordinates, the velocity and angular distri- bution of N＋ fragment ions in MPCM coordinates are obtained and discussed, respectively.

Drag Effects of Solute and Second Phase Distributions on the Grain Growth Kinetics of Pre-Extruded Mg-6Zn Alloy

In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing was conducted on a Gleeble-1500 thermo-mechanical simulator.The mean grain size Dg of each annealed specimen was measured by the quantitative metallography technique.The grain growth kinetics of the Mg-6Zn alloy annealed at 473-623 K was obtained as Dg^4- Dg0^4=2.25 ×10^11 exp（-95450）by the least square linear regression method.The deviation of grain growth exponent n = 4 from the theoretical value of 2 may be attributed to the presence of solute zinc and second phases which will retard the boundary migration.Microscopic observations show that the non-uniform distribution of grain size for samples pre-extruded or annealed at low temperatures is closely related to the non-uniform distribution of fine and dispersed second phases but not to the non-uniform distribution of solute zinc.This indicates that second phase pinning effect plays an important role in microstructure refinement.

Kinetic theory for aquatic animal distribution simulation

Identifying the underlying mechanisms that influence the spatial patterns in populations improves the forecasts of the alternative management strategies on the spatial dynamics of the populations, which are critical for assessing and managing the fisheries and improving the water resource management. This paper described a new approach of the numerical model for the prediction of the aquatic animal distribution in the flows. The model was developed based on the kinetic theory of gases, the mechanism of the aquatic animal movement and the flow hydrodynamic patterns. The model was validated using the available experimental data and an acceptable agreement was obtained. A comprehensive parameter study was then conducted to help understand the impact and the sensitivity of each parameter to the aquatic animal distribution. The promising results of the model reveal the prospect of applying this model to the reliable prediction of the aquatic animal distribution within a relatively large water area.

Effects of Ni on austenite stability and fracture toughness in high Co-Ni secondary hardening steel

Three kinds of high Co Ni secondary hardening steels with different Ni contents were studied. The nanoscale austenite layers formed at the interface of matensite laths were observed. Both observation and diffusion kinetic simulation results showed that both Ni and Co did not obtain enough time to get the equilibrium content in this system. The Ni content in austenite layers decreased significantly, and Co content increased slightly with the decrease of Ni content in overall composition. The austenite stability was estimated by Olson-Cohen model, in which both chemical and mechanical driving force could be calculated by equilibrium thermodynamic and Mohr＇s circle methods, respectively. Simulation and mechanical test results showed that The decrease of Ni content in austenite layers would cause the change of austenite stability and decrease the fracture toughness of the steels. When the Ni content in the overall composition was lower than 7 wt. %, the Ni content in y phase would be lower than 20 wt.%. And the simulation value of M; （stress induced critical martensite transformation temperature） would be up to 80 ℃, which was about 60℃ higher than room temperature. Based on the analysis, the Ni content in the overall composition of high Co Ni secondary hardening steels should be higher than 8 wt. % in order to obtain a good fracture toughness.

Experimental and numerical study of pseudo-2D circulating fluidized beds

We present experimental investigations and numerical simulations of a pseudo-2D riser. Experiments were performed for various airflow rates, particle types/diameters, and particle size distributions. Pres- sure distributions along the wall of the riser were measured, Additional measurements from a smaller pseudo-2D riser （Kallio et al., 2009; Shah et al., 2012） were used to analyze horizontal solids volume fraction profiles. The experimental data were compared with simulation results carried out using an Euler-Euler approach, A mesh sensitivity study was conducted for numerical simulations and effects associated with simplifying real 3D geometry to a 2D model were examined. In addition, the effect of using an algebraic equation to represent the granular temperature versus a full partial differential equation also was examined for numerical simulations. Results showed small but significant near-wall sensitivity of the flow variables to mesh size. Substantial differences in mean pressure, solids distribution, and solid velocities were obtained, when 2D and 3D simulation results were compared. Finally, applying the simplified granular temperature equation for turbulent fluidization and for dilute-phase transport can lead to incorrect predictions in models,