Experimental study on dynamic load magnification factor for ballastless track-subgrade of high-speed railway

The magnitude of dynamic load produced by high-speed trains depends on many factors,of which train speed is the most critical one.However,it is quite difficult to determine the effect of train speed on dynamic load using the theoretical methods due to the complexity of the interaction between vehicle and track-subgrade.Thus large-scale model test has gradually become an important approach for studying dynamic responses of ballastless track-subgrade of high-speed railway.In this study,a full-scale model of ballastless track-subgrade was constructed in accordance with the design and construction standards for Shanghai-Nanjing intercity high-speed railway line firstly.Then,the dynamic strain of slab and the dynamic earth pressure of subgrade were measured by conducting single wheel axle excitation test.In addition,the relationship between the dynamic load magnification factor（DLF） and the train speed was obtained.Finally,the DLF of track-subgrade under different train speeds was proposed,similar to that given by German Railway Standard.

EFFECT OF GEAR WIDTH AND HELIX ANGLE ON FACTOR OF DYNAMIC LOAD OF DOUBLE CIRCULAR ARC HELICAL GEARING

Based on theory of mechanical dynamics, meshing characteristic as well as thedynamic model of double circular arc helical gearing, an analysis approach and a computer programhave been developed for studying the state of dynamic load and factor of dynamic load of thegearing, the changing situation of dynamic load and dynamic load factor vs some affecting factorssuch as gear width, helix angle and accuracy grade etc are investigated. A series of conclusions areobtained: ①With the increasing in the values of gear width, the dynamic load factor appears slowdecreasing tendency in most region of gear width. ②When the accuracy grades of the gearing areimproved, the values of dynamic load factor decrease. ③The value of dynamic load factor appears adecreasing tendency with the increasing of value of helix angle at the same ratio of criticalrotational speed.

A novel approach to the dynamic response analysis of Euler-Bernoulli beams resting on a Winkler soil model and subjected to impact loads

This work presents a novel approach to the dynamic response analysis of a Euler-Bernoulli beam resting on a Winkler soil model and subjected to an impact loading.The approach considers that damping has much less importance in controlling the maximum response to impulsive loadings because the maximum response is reached in a very short time,before the damping forces can dissipate a significant portion of the energy input into the system.The development of two sine series solutions,relating to different types of impulsive loadings,one involving a single concentrated force and the other a distributed line load,are presented.This study revealed that when a simply supported Euler-Bernoulli beam,resting on a Winkler soil model,is subject to an impact load,the resulting vertical displacements,bending moments and shear forces produced along the span of the beam are considerably affected.In particular,the quantification of this effect is best observed,relative to the corresponding static solution,via an amplification factor.The computed impact amplification factors,for the sub-grade moduli used in this study,were in magnitude greater than 2,thus confirming the multiple-degree-of-freedom nature of the problem.

Dynamic caustics test of blast load impact on neighboring different cross-section roadways

Using digital laser dynamic caustics experimental system and conducting simulation experiment researched the influence rule of blasting excavation of a new roadway on neighboring existed different cross-section roadways. The experimental results show that the influence of blast load on adjacent roadway has a good relationship with the cross-section of roadway. The expansion distance of precrack existed in circular, arch-wall, rectangular roadway is respectively 1.76, 1.61 and 0 cm under blast load.At the same time, the direct-blast side of rectangular roadway has more obvious damage compared with circular and arch-wall roadway. It explains that plane reflects more stress wave than arc, so that it exerts more tensile failure in the direct-blast side, which leads to less stress wave diffracting to the precrack in the back-blast side. When the precrack extends, higher value dynamic stress intensity factor in circular roadway works longer than that of arch-wall roadway. Indirectly, it explains that plane's weakening function on stress wave is significantly stronger than arc. Stress wave brings about self-evident influence on the upper and bottom endpoints of the rectangular roadway, and it respectively extends 1.03, 2.06 cm along the line link direction of the center of the blasthole and the upper and bottom endpoints on the right wall.

Crack propagation mechanism of compression-shear rock under static-dynamic loading and seepage water pressure

To reveal the water inrush mechanics of underground deep rock mass subjected to dynamic disturbance such as blasting, compression-shear rock crack initiation rule and the evolution of crack tip stress intensity factor are analyzed under static-dynamic loading and seepage water pressure on the basis of theoretical deduction and experimental research. It is shown that the major influence factors of the crack tip stress intensity factor are seepage pressure, dynamic load, static stress and crack angle. The existence of seepage water pressure aggravates propagation of branch cracks. With the seepage pressure increasing, the branch crack experiences unstable extension from stable propagation. The dynamic load in the direction of maximum main stress increases type I crack tip stress intensity factor and its influence on type II crack intensity factor is related with crack angle and material property. Crack initiation angle changes with the dynamic load. The initial crack initiation angle of type I dynamic crack fracture is 70.5°. The compression-shear crack initial strength is related to seepage pressure, confining pressure, and dynamic load. Experimental results verify that the initial crack strength increases with the confining pressure increasing, and decreases with the seepage pressure increasing.

Dynamic fracture behavior of rock under impact load using the caustics method

We studied the dynamic fracture mechanical behavior of rock under different impact rates. The fracture experiment was a three-point bending beam subjected to different impact loads monitored using the reflected caustics method. The mechanical parameters for fracture of the three-point bending beam specimen under impact load are analyzed. The mechanism of crack propagation is discussed. Experimental results show that the dynamic stress intensity factor increases before crack initiation. When the dynamic stress intensity factor reaches its maximum value the crack starts to develop. After crack initiation the dynamic stress intensity factor decreases rapidly and oscillates. As the impact rate increases the cracks initiate earlier, the maximum value of crack growth velocity becomes smaller and the values of dynamic stress intensity factor also vary less during crack propagation. The results provide a theoretical basis for the study of rock dynamic fracture.

State space reconstruction of classic methods in air-conditioning dynamic load calculation

In actual air-conditioning systems,accurate calculation of dynamic loads is demandedfor the energy and materials saving and comfort control.At about the beginning of the1970s,researchers abroad developed the harmonic wave method(HWM),thermal responsefactor method(TRFM)and Z-transfer function method(ZTFM),and made greatachievements on the transition of air-conditioning loads calculation from steady methods

Dynamic amplification factors for a system with multiple-degrees-of-freedom

It is well-known that the responses of a structure are different when subjected to a static load or a sudden step load.The dynamic amplification factor(DAF),which is defined as the ratio of the amplitude of the vibratory response to the static response,is normally used to depict the dynamic effect.For a single-degree-of-freedom system(SDOF)subjected to a sudden dynamic load,the maximum value of DAF is 2.Many design guidelines therefore use 2 as an upper bound to consider the dynamic effect.For a civil engineering structure,which is normally a multiple-degrees-of-freedom(MDOF)system,the DAF may exceed 2 in certain circumstances.The adoption of 2 as the upper bond as suggested by the design guidelines therefore may lead to unsafe structural design.Very limited studies systematically investigate the DAF of a MDOF sysCorrespondence to:Bi Kaiming,Centre for Infrastructure Monitoring and Protection,School of Civil and Mechanical Engineering,Curtin University,Kent Street,Bentley WA 6102,Australia Tel:(+61)892665139 E-mail:kaiming.bi@curtin.edu.autem.This study theoretically investigates the DAF of a MDOF system when it is subjected to a step load based on the fundamental theory of structural dynamics.The condition on which the DAF may exceed 2 is defined.Two numerical examples and one experimental study of a cable-stayed bridge subjected to sudden cable loss are presented to illustrate the problem.

Evaluation of vertical impact factor coefficients for continuous and integral railway bridges under high-speed moving loads

In the railway bridge analysis and design method,dynamic train loads are regarded as static loads enhanced by an impact factor(IF).The IF coefficients for various railway bridges have been reported as a function of span length or frequency of the bridges in Eurocode(2003).However,these IF coefficient values neglect the effects of very high speeds(>200 km/h)and soil-structure interaction(SSI).In this work,a comprehensive study to assess the impact factor coefficients of mid-span vertical displacements for continuous and integral railway bridges subjected to high-speed moving loads is reported.Three different configurations,each for the three-dimensional(3D)continuous and integral bridge,are considered.Also,single-track(1-T)and two-track(2-T)“real train”loading cases for both these bridge types are considered.Subsequently,finite element analysis of the full-scale 3D bridge models,to identify their IF values,considering the effects of SSI for three different soil conditions,is conducted.The IF values obtained from the study for both bridge types are comparable and are greater than the values recommended by Eurocode(2003).The results reveal that with a loss of soil stiffness,the IF value reduces;thus,it confirms the importance of SSI analysis.

Analysis of dynamic stress intensity factors of three-point bend specimen containing crack

A new formula is obtained to calculate dynamic stress intensity factors of the three-point bending specimen containing a single edge crack in this study. Firstly, the weight function for three-point bending specimen containing a single edge crack is derived from a general weight function form and two reference stress intensity factors, the coefficients of the weight function are given. Secondly, the history and distribution of dynamic stresses in uncracked three-point bending specimen are derived based on the vibration theory. Finally~ the dynamic stress intensity factors equations for three-pointing specimen with a single edge crack subjected to impact loadings are obtained by the weight function method. The obtained formula is verified by the comparison with the numerical results of the finite element method （FEM）. Good agreements have been achieved. The law of dynamic stress intensity factors of the three-point bending specimen under impact loadings varing with crack depths and loading rates is studied.

CONVOLUTION OF THE IMPACT THREE-DIMENSIONAL ELASTO-DYNAMICS AND DYNAMIC STRESS INTENSITY FACTOR FOR AN ELLIPTIC CRACK

This paper presents a formulation for three-dimensional elasto-dynamics with an elliptic crack based on the Laplace and Fourier transforms and the convolution theorem. The dynamic stress intensity factor for the crack is determined by solving a Fredholm integral equation of the first kind. The results of this paper are very close to those given by the two-dimensional dual integral equation method.

THE THREE-DIMENSIONAL STRESS INTENSITY FACTOR UNDER MOVING LOADS ON THE CRACK FACES

The dynamic stress intensity factor history for a half plane crack in an otherwise unbounded elastic body,with the crack faces subjected to a traction distribution consisting of two pairs of combined mode point loads that move in a direction perpendicular to the crack edge is considered.The analytic expression for the combined mode stress intensity factors as a function of time for any point along the crack edge is obtained.The method of solution is based on the application of integral transform together with the Wiener-Hopf technique and the Cagniard-de Hoop method. Some features of the solution are discussed and graphical results for various point load speeds are presented.

THREE-DIMENSIONAL ELLIPTIC CRACK UNDER IMPACT LOADING

The dynamic stress intensity factor of a three-dimensionalelliptic crack under impact loading is determined with the finiteelement method. The computation results can take into account theinfluence of time and the ratio of the wave speeds on the stressintensity factor. The present method is suitable not only forthree-dimensional dynamic crack, but also for three-dimensionaldynamic contact.

Experimental investigation of rigid confinement effects of radial strain on dynamic mechanical properties and failure modes of concrete

In this study,to confirm the effect of confining pressure on dynamic mechanical behavior and failure modes of concrete,a split Hopkinson pressure bar dynamic loading device was utilized to perform dynamic compressive experiments under confined and unconfined conditions.The confining pressure was achieved by applying a lateral metal sleeve on the testing specimen which was loaded in the axial direction.The experimental results prove that dynamic peak axial stress,dynamic peak lateral stress,and peak axial strain of concrete are strongly sensitive to the strain rate under confined conditions.Moreover,the failure patterns are significantly affected by the stress-loading rate and confining pressure.Concrete shows stronger strain rate effects under an unconfined condition than that under a confined condition.More cracks are created in concrete subjected to uniaxial dynamic compression at a higher strain rate,which can be explained by a thermal-activated mechanism.By contrast,crack generation is prevented by confinement.Fitting formulas of the dynamic peak stress and dynamic peak axial strain are established by considering strain rate effects(50–250 s-1)as well as the dynamic confining increase factor(DIFc).

Dynamic Analysis Method of Offshore Jack-up Platforms in Regular and Random Waves

一与它的特别结构，杰克起来，站台处于极端条件在复杂环境负担下面显示出明显的动态特征。在这篇论文，拿简化 3-D 极端暴风雨里的动态模型作为研究目标调节的有限元素，一个短暂动态分析方法被建议，它在常规、不规则的波浪负担下面。在极端条件下面的动态分析的步骤与一个应用盒子被说明，并且动态扩大因素(DAF ) 为底的每个反应参数是计算的砍，翻的时刻和壳摇摆。最后，结构的反应结果动态、静态被比较并且分析。结果显示静态的力量分析考虑到计算效率和精确性是必要的，杰克起来，平台足够不在动态负担下面正在包括波浪和当前的、进一步有活力的反应分析。

A HALF PLANE CRACK UNDER THREE-DIMENSIONAL COMBINED MODE IMPACT LOADING

The dynamic stress intensity factor history for a half plane crack in an otherwise unbounded elastic body, with the crack faces subjected to a traction distribution consisting of two pairs of suddenly-applied shear line loads is consid- ered. The analytic expression for the combined mode stress intensity factors as a function of time is obtained. The method of solution is based on the application of integral transforms and the Wiener-Hopf technique. Some features of the solutions are discussed and graphical numerical results are presented.

SEMI-ELLIPTIC SURFACE CRACK IN AN ELASTIC SOLID WITH FINITE SIZE UNDER IMPACT LOADING

In this paper a semi-elliptic surface crack problem in an elastic solid of finite size under impact loading is investigated. An analysis is performed by means of fracture dynamics and the finite element method, and a three-dimensional finite element program is developed to compute the dynamic stress intensity factor. The results reveal that the effects of the solid＇s boundary surface, crack surface, material inertia and stress wave interactions play significant roles in dynamic fracture.

THEORETICAL INVESTIGATION ON STATE OF LOAD DISTRIBUTION AMONG CONTACT BEARINGS OF DOUBLE CIRCULAR ARC HELICAL GEARS

A dynamic analysis approcach to investigate the state of load distribution among contact bearings of double circular are belical gears is proposed and a computer program is developed for calculating the factor of iced distribution based on the theory of W-N gears. The changing situations of load distribution among contact bearings of the gears influenced by main issues are analyzed by a series of parametric studies.

THE DYNAMIC BUCKLING OF AN ORTHOTROPIC CYLINDRICAL THIN SHELL UNDER TORSION VARYING AS A POWER FUNCTION OF TIME

The subject of this investigation is to study the buckling of orthotropic cylindrical thin shells under torsion, which is a power function of time. The dynamic stability and compatibility equations are obtained first. These equations are subsequently reduced to a time dependent differential equation with variable coefficient by using Galerkin's method. Finally, the critical dynamic and static loading, the corresponding wave numbers, the dynamic factors, critical time and critical impulse are found analytically by applying the Ritz type variational method. Using those results, the effects of the variations of the power of time in the torsion load expression, of the loading parameter, the ratio of the Young's moduli and the ratio of the radius to thickness on the critical parameters are studied numerically. It is observed that these factors have appreciable effects on the critical parameters of the problem in the heading.

循环荷载作用下土工格栅加筋黄土动力特性研究

【目的】由于黄土所具有的结构疏松、抗剪性低,以及对水、力及震动都十分敏感等工程特性,故探究采用双向土工格栅对西宁地区黄土加筋前后土体动力性能的改善效果。【方法】采用GDS双向动三轴测试系统开展不同加筋层间距、不同围压、不同动应力幅值工况条件下加筋黄土的动三轴试验,分析循环荷载作用下加筋层间距对黄土动强度、动剪切模量、阻尼比等动力响应特性的影响,探讨分析加筋黄土动力响应特性的演化规律。【结果】结果显示:黄土动应变随着动应力的增大而增大,骨干曲线呈现应变强化型,并且骨干曲线随加筋层间距的减小逐渐由曲线型过渡为直线型;随着加筋层间距的减小,黄土强度随之增大,随着围压和加筋层间距的增加,黄土幅值剪应力明显增大,动剪应变减小,阻尼比明显减小。【结论】结果表明:围压和加筋层间距对加筋黄土的动力特性具有显著的增强作用,且存在一个最优加筋层间距。研究成果可为西宁地区加筋黄土道路设计提供参考依据。