Step-scheme porous g-C3N4/Zn0.2Cd0.8S-DETA composites for efficient and stable photocatalytic H2 production

In recent years,environmental pollution and energy crisis have become increasingly serious issues owing to the burning of fossil fuels.Among the many technologies,decomposition of water to produce hydrogen has attracted much attention because of its sustainability and non-polluting characteristic.However,highly efficient decomposition of water that is driven by visible light is still a challenge.Herein,we report the large-scale preparation of step-scheme porous graphite carbon nitride/Zn0.2Cd0.8S-diethylenetriamine(Pg-C3N4/Zn0.2Cd0.8S-DETA)composite by a facile solvothermal method.It was found by UV-vis spectroscopy that 15%Pg-C3N4/Zn0.2Cd0.8S-DETA exhibited suitable visible absorption edge and band gap for water decomposition.The hydrogen production rate of 15%Pg-C3N4/Zn0.2Cd0.8S-DETA composite was 6.69 mmol g^-1 h^-1,which was 16.73,1.61,and 1.44 times greater than those of Pg-C3N4,CdS-DETA,and Zn0.2Cd0.8S-DETA,respectively.In addition,15%Pg-C3N4/Zn0.2Cd0.8S-DETA composite displayed excellent photocatalytic stability,which was maintained for seven cycles of photocatalytic water splitting test.We believe that 15%Pg-C3N4/Zn0.2Cd0.8S-DETA composite can be a valuable guide for the development of solar hydrogen production applications in the near future.

In situ fabrication of CdMoO4/g-C3N4 composites with improved charge separation and photocatalytic activity under visible light irradiation

To further improve the charge separation and photocatalytic activities of g-C3N4 and CdMoO4 under visible light irradiation,CdMoO4/g-C3N4 composites were rationally synthesized by a facile precipitation-calcination procedure.The crystal phases,morphologies,chemical compositions,textural structures,and optical properties of the as-prepared composites were characterized by the corresponding analytical techniques.The photocatalytic activities toward degradation of rhodamine B solution were evaluated under visible light irradiation.The results revealed that integrating CdMoO4 with g-C3N4 could remarkably improve the charge separation and photocatalytic activity,compared with those of pristine g-C3N4 and CdMoO4.This would be because the CdMoO4/g-C3N4 composites could facilitate the transfer and separation of the photoexcited electron-hole pairs,which was confirmed by electrochemical impedance spectroscopy,transient photocurrent responses,and photoluminescence measurements.Moreover,active species trapping experiments demonstrated that holes(h+)and superoxide radicals(?O2?)were the main active species during the photocatalytic reaction.A possible photocatalytic mechanism was proposed on the basis of the energy band structures determined by Mott-Schottky tests.This work would provide further insights into the rational fabrication of composites for organic contaminant removal.

Fabrication of Fine-Grained Si_3N_4-Si_2N_2O Composites by Sintering Amorphous Nano-sized Silicon Nitride Powders

Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .

In-situ polymerization for PPy/g-C_3N_4 composites with enhanced visible light photocatalytic performance

Polypyrrole‐modified graphitic carbon nitride composites(PPy/g‐C3N4)are fabricated using an in‐situ polymerization method to improve the visible light photocatalytic activity of g‐C3N4.The PPy/g‐C3N4 is applied to the photocatalytic degradation of methylene blue(MB)under visible light irradiation.Various characterization techniques are employed to investigate the relationship between the structural properties and photoactivities of the as‐prepared composites.Results show that the specific surface area of the PPy/g‐C3N4 composites increases upon assembly of the amorphous PPy nanoparticles on the g‐C3N4 surface.Owing to the strong conductivity,the PPy can be used as a transition channel for electrons to move onto the g‐C3N4 surface,thus inhibiting the recombination of photogenerated carriers of g‐C3N4 and improving the photocatalytic performance.The elevated light adsorption of PPy/g‐C3N4 composites is attributed to the strong absorption coefficient of PPy.The composite containing 0.75 wt%PPy exhibits a photocatalytic efficiency that is 3 times higher than that of g‐C3N4 in 2 h.Moreover,the degradation kinetics follow a pseudo‐first‐order model.A detailed photocatalytic mechanism is proposed with·OH and·O2-radicals as the main reactive species.The present work provides new insights into the mechanistic understanding of PPy in PPy/g‐C3N4 composites for environmental applications.

Microstructure and Mechanical Properties of Si_3N_4 Composites Containing SiC Platelet

Hoppressed Si3N4/SiC platelet composites had been investigated with respect to their microstructure and mechanical properties. The results indicate that Vickers hardness, elastic modulus and fracture toughness of the composites were increased by the addition of SiC platelet until the content up to 20 vol pct. A slight decrease in flexural Strength was measured at room temperature with increasing SiC platelet content. The high temperature flexural strength tests at 1150, 1250, and 1350℃ were conducted. It was found that the flexural strength at elevated temperature was degraded with the rising temperature, and the downward trend of flexural strength for the composite containing 10 vol. pct SiC platelet was less. The results indicate that SiC platelet had a positive influence on the high temperature strength. Effects of SiC platelet reinforcement were presented

Fabrication and characterization of SiO_(2(f))/Si)_3N_4 composites

A silicon dioxide fiber-reinforced silicon nitride matrix （SiOJSi3N4） composite used for radomes was prepared by chemical vapor infiltration （CVI） process using the SiCl4-NH3-H2 system. The effects of the process conditions, including infiltration temperature, infiltration time, and gas flux were investigated. The energy dispersion spectra （EDS） result showed that the main elements of this composite contained Si, N, and O. The X-ray diffraction （XRD） results indicated that phases of the composite before and after treatment at 1350℃ were all amorphous. A little fiber pull-out was observed on the cross section of the composite by scan electron microscope （SEM）. As a result, the composite exhibited good thermal stability, but an appropriate interface was necessary between the fiber and the matrix.

Processing and performance of 2D fused-silica fiber reinforced porous Si_3N_4 matrix composites

Two-dimension （2D） fused-silica fiber reinforced porous silicon nitride matrix composites were fabricated using slurry impregnation and cyclic infiltration with colloidal silica sol. The microstructure and fracture surface were characterized by SEM, the mechanical behavior was investigated by three-point bending test, and the dielectric constant was also measured by impedance analysis. The microstructure showed that the fiber and the matrix had a physical bonding, forming a clearance interface. The mechanical behavior suggested that the porous matrix acted as crack deflection, and the fracture surface had a lot of fiber pull-out. However, the interlaminar shear strength was not so good. The dielectric constant of the composites at room temperature was about 2.8-3.1. The relatively low dielectric constant and non-catastrophic failure indicated the potential application in the radome materials field. 2008 University of Science and Technology Beijing. All rights reserved.

夹层结构Cf-Si_3N_4复合材料微波介电响应机理研究

以短切炭纤维、氮化硅为原料,采用凝胶注模工艺,在1600℃、N2气氛下无压烧结制备了夹层结构Cf-Si_3N_4复合材料。采用网络矢量分析仪测试了夹层结构Cf-Si_3N_4复合材料在X波段的介电响应行为,并通过理论建模深入分析了该复合材料的微波介电响应机理。结果表明:短切炭纤维呈二维分布的夹层结构,Cf-Si_3N_4复合材料介电常数随着炭纤维面密度增加存在"阈值"现象。通过修正Debye模型,提出了夹层结构Cf-Si_3N_4复合材料在炭纤维形成导通网络后的介电响应理论模型,揭示了夹层结构Cf-Si_3N_4复合材料介电损耗频散特性的机理。研究结果还表明,在短切炭纤维刚刚形成导通网络时,复合材料的弛豫时间存在较大分散性,介电常数可采用多弛豫时间函数分段描述法。随着炭纤维面密度逐步增加,弛豫时间的分散性减小,分段弛豫时间函数演化成单一弛豫时间理论模型。

AlSi11/ Si₃N₄Interpenetrating Composites Tribology Properties of Aluminum Matris Composites

In present work, the metal-ceramic interpenetrating composites (IPCs) as AlSi11/ Si3N4 are fabricated by infiltrating technique. IPCs exhibit special characterization of brittle ceramic reinforced phase introduced by ductile metal matrix phase. During the sliding wear processes, IPCs exhibit four wear mechanism such as initial adhesive wear, mixed adhesive and abrasive wear, adhesive wear and final abrasive wear. Reinforcements inhibit plastic flow and restrict propagation of wear cracks. Increase in the volume fraction of reinforcement leads to improvement in the wear resistance. Under higher load and lower round speed conditions, the friction coefficients are lower than that of relative conditions.

Effect of annealing on microstructure and properties of Si_3N_4-AlN composite ceramics

Aiming at developing novel microwave-transparent ceramics with low dielectric loss, high thermal conductivity and high strength, Si3Na-AIN （30%, mass fraction） composite ceramics with La203 as sintering additive were prepared by hot-pressing at 1 800 ℃ and subsequently annealed at 1 450 ℃ and 1 850 ℃ for 2 h and 4 h, respectively. The materials were characterized by XRD and SEM. The effect of annealing process on the phase composition, sintering performance, microstructure, bending strength, dielectric loss and thermal conductivity of the materials was investigated. The results showed that both annealing at 1 850 ℃ and 1 450 ℃ promoted the phase transformation of α-Si3N4 to β-Si3N4. After annealing at 1 850 ℃, grain growth to a certain extent occurred in the materials. Especially, the elongated β-Si3N4 grains showed a slight increase in diameter from 0.2 μm to 0.6 μm approximately and a decrease in aspect ratio. As a result, as the annealing time increased to 4 h, the bending strength declined from 456 MPa to 390 MPa, whereas the dielectric loss decreased to 2.15× 10^-3 and the thermal conductivity increased to 16.3 W/（m.K） gradually. When annealed at 1 450 ℃, increasing the annealing time to 4 h significantly promoted the crystallization of glassy phase to La2Si6N803 phase in the materials, which led to the increase in bending strength to 619 MPa and thermal conductivity to 15.9 W/（m·K）, respectively, and simultaneously the decrease in dielectric loss to 1.53× 10^-3.

Visible Light-induced Cr-doped SrTiO_3-g-C_3N_4 Composite for Improved Photocatalytic Performance

Novel visible light-induced Cr-doped Sr Ti O3-g-C3N4 composite photocatalysts were synthesized by introducing polymeric g-C3N4. The composite photocatalyst was characterized by X-ray diffraction（XRD）, high-resolution transmission electron microscopy（HRTEM）, Fourier transform infrared（FT-IR） spectroscopy, UV-vis diffuse reflection spectroscopy, photoluminescence（PL） spectroscopy and BET surface area measurements. The photocatalytic oxidation ability of the novel composite photocatalyst was evaluated using methyl orange（MO） as a target pollutant. The photocatalysts exhibited a significantly enhanced photocatalytic performance in degrading MO. The optimal g-C3N4 content for the photodegradation activity of the composite photocatalysts was determined. The as-prepared composite photocatalyst exhibits an improved photocatalytic activity due to enhancement of photo-generated electron-hole separation at the interface.

Synthesis of BiVO_4-g-C_3N_4 Composite Photocatalyst with Improved Visible Light-induced Photocatalytic Activity

The novel visible light-induced carbon nitride（g-C3N4） and Bi VO4 composite photocatalysts were obtained through a simple mixing-calcination method. The physical and photophysical properties of the Bi VO4-g-C3N4 composites were investigated by X-ray diffraction（XRD）, Fourier transform infrared（FTIR） spectroscopy, UV-vis diffuse reflection spectroscopy, high-resolution transmission electron microscopy（HRTEM）, photoluminescent（PL） spectroscopy, and BET surface area measurements. Photocatalytic oxidation ability of the prepared samples was examined by studying the degradation of rhodamine B（Rh B） as a target pollutant under visible-light irradiation. The composite photocatalysts exhibited an enhanced photocatalytic performance in degrading Rh B. The optimal g-C3N4 content of the composite photocatalysts was determined for the photodegradation activity. The improved photocatalytic activity of the as-prepared composite photocatalyst may be attributed to the enhancement of photo-generated electron-hole separation at the interface.

The effects of radiation damage on power VDMOS devices with composite SiO_2-Si_3N_4 films

Total dose effects and single event effects on radiation-hardened power vertical double-diffusion metal oxide semiconductor（VDMOS） devices with composite SiO2-Si3N4 film gates are investigated.The relationships among the important electrical parameters of the samples with different thickness SiO2-Si3N4 films,such as threshold voltage,breakdown voltage,and on-state resistance in accumulated dose,are discussed.The total dose experiment results show that the breakdown voltage and the on-state resistance barely change with the accumulated dose.However,the relationships between the threshold voltages of the samples and the accumulated dose are more complex,and not only positively drift,but also negatively drift.At the end of the total dose experiment,we select the group of samples which have the smaller threshold voltage shift to carry out the single event effect studies.We find that the samples with appropriate thickness ratio SiO2-Si3N4 films have a good radiation-hardening ability.This method may be useful in solving both the SEGR and the total dose problems with the composite SiO2-Si3N4 films.

Synergistic photocatalytic effect of porous g-C_3N_4 in a Cr(Ⅵ)/4-chlorophenol composite pollution system

The photocatalytic reduction of aqueous Cr(VI)to Cr(III)was preliminarily studied using porousg‐C3N4as a photocatalyst under acidic conditions.The observed synergistic photocatalytic effect ofporous g‐C3N4on a Cr(VI)/4‐chlorophenol(4‐CP)composite pollution system was further studiedunder different pH conditions.Compared with single‐component photocatalytic systems for Cr(VI)reduction or4‐CP degradation,the Cr(VI)reduction efficiency and4‐CP degradation efficiency weresimultaneously improved in the Cr(VI)/4‐CP composite pollution system.The synergistic photocatalyticeffect in the Cr(VI)/4‐CP composite pollution system can be attributed to the acceleratedredox reaction between dichromate and4‐CP by electron transfer with porous g‐C3N4.

Optimization of friction and wear behaviour of Al-Si_3N_4 nano composite and Al-Gr-Si_3N_4 hybrid composite under dry sliding conditions

The tribological behaviour of gravity die stir cast LM6alloy with graphite(Gr)and silicon nitride nanoparticles was investigated.Al?Gr?Si3N4hybrid composite,Al?Si3N4nanocomposite and Al?Gr nanocomposites were separately fabricated to investigate their frictional and wear characteristics under dry sliding conditions.EDS was used to ensure the uniform presence of nano Si3N4and graphite in the cast.L9orthogonal array method was chosen to conduct the experiments to study the effect of different applied loads(20,30and40N)and sliding distances(1,2and3km).The results showed that the respective wear rate and coefficient of friction(COF)decreased by25%and15%for hybrid composite when compared with those of Al?Si3N4nanocomposite whereas the wear rate and COF of Al?Gr was found to be very minimal.The micro Vickers hardness of the hybrid composite was14%more than that of the simple nanocomposite and there was not much notable variation for Al?Gr and Al?Si3N4nanocomposite materials.Scanning electron microscope was used to analyze the worn surface and subsurface,from which it was noted that the predominant wear mechanisms observed were abrasive for nanocomposite and both abrasive and adhesive mechanism for hybrid composite.Analysis of variance(ANOVA)and F-test were used to check the validity model and to determine the significant parameters affecting the wear rates.

INTERFACIAL REACTION BEHAVIOUR AND JOINT STRENGTH OF TiC_p/Si_3N_4 COMPOSITE BONDED WITH Al FOIL

１ＩＮＴＲＯＤＵＣＴＩＯＮＴｉＣｐ／Ｓｉ３Ｎ４ｃｏｍｐｏｓｉｔｅｃｅｒａｍｉｃｓｈａｖｅｅｘｃｅｌｌｅｎｔｐｈｙｓｉｃａｌ，ｃｈｅｍｉｃａｌａｎｄｍｅｃｈａｎｉｃａｌｐｒｏｐｅｒｔｉｅｓ，ａｎｄｔｈｅｙａｒｅａｐｐｌｉｅｄｗｉｄｅｌｙｉｎｓｅｖｅ...

High Temperature Creep behaviour of a Si_3N_4 Whisker Reinforced Al-Fe-V-Si Composite

The creep behaviour of β-Si3N4 whisker reinforced Al-8.5Fe-1.3V-1.7Si composite has been investigated at the temperature 773 and 823 K. The results are characterized by high stress exponent and high apparent creep activation energy The creep data can be interpreted based on the incorporation of a threshold Stress and a load transfer coefficient into the power-law creep equation. A good correlation between the normalized creep rate and normalized effective stress is available which demonstrates that the creep behaviour of both the alloy and the composite is controlled by the matrix lattice self-diffusion in AI. EXamination on microstructure shows that edge dislocations exist at the interfaces between two adjacent whiskers and the intedeces emit edge dislocations in parallel paired-columns.

g-C_(3)N_(4)/Ag_(2)O复合光催化剂的制备及其近红外光催化性能

通过简易化学合成法制备了g-C_(3)N_(4)/Ag_(2)O_(p-n)异质结复合光催化剂,利用XRD、XPS、SEM、TEM、DRS等对所制复合材料的物相结构、微观形貌及光学性质进行表征,借助近红外光下催化降解罗丹明B(RhB)试验评价其光催化活性,重点探讨了g-C_(3)N_(4)/Ag_(2)O_(p-n)异质结复合材料的光催化降解机理。结果表明,当g-C_(3)N_(4)、Ag_(2)O质量比为1∶16时,所制g-C_(3)N_(4)/Ag_(2)O复合光催化剂具有最佳的近红外光催化性能且活性稳定;h+和·O-2活性自由基在近红外光催化降解过程中发挥了主要作用。

新型Si_3N_4/TiC_(nano)复合陶瓷材料的制备及性能

本文利用热压烧结方式制备了新型Si3N4/TiCnano复合陶瓷材料,对材料的配方及烧结工艺进行了优化,采用XRD、SEM等手段分析了材料的微观结构,研究了烧结条件对材料性能的影响机理。结果表明,所研究的材料具有良好的力学性能。

用Y_2O_3Al_2O_3SiO_2Si_3N_4钎料连接氮化硅复相陶瓷

研究了用Ｙ２Ｏ３Ａｌ２Ｏ３ＳｉＯ２Ｓｉ３Ｎ４ 钎料对氮化硅复相陶瓷的连接． 对连接界面进行ＳＥＭ、ＥＰＭＡ和ＸＲＤ分析．接头强度随着保温时间、连接温度的增加而逐渐增加． 在达到峰值后，连接强度逐渐降低．在ＹＡＳ钎料中添加氮化硅， 可以降低接头界面的热应力，改善接头强度． 微观分析表明：接头强度的变化主要与界面反应和界面孔洞损伤有关．