Study on Numerical Simulation of the Impact of the Land-Surface Process in a Meiyu Front Rainstorm

[Objective] The research aimed to carry out numerical simulation on impact of land-surface process in a Meiyu front rainstorm.[Method] Based on the meso-scale atmospheric non-hydrostatic model GRAPES-Meso which coupled with NOAH land-surface module,a Meiyu front rainstorm in Jianghuai basin during 6-8 July,2005 was simulated.Via sensitivity tests with and without land-surface process,the impact of land-surface process on Meiyu front rainstorm was studied.[Result] GRAPES-Meso which coupled with NOAH land-surface process could simulate daily variation characteristics of Meiyu front precipitation and atmospheric low-level southwest jet.The land-surface process could improve the simulations of precipitation initiation,intensity and distribution.The improvement of precipitation initiation simulation was especially obvious,which solved spin-up problem of model to some extent.When the land-atmosphere interaction wasn’t considered,the precipitation initiation of model was very slow.The intensity evolution of simulated precipitation was different from actual situation.Moreover,it couldn’t simulate daily variation characteristics of precipitation and southwest jet.[Conclusion] The land-surface process had important impact on Meiyu process in Jianghuai basin.

Review on simulation of land-surface processes on the Tibetan Plateau

The Tibetan Plateau(TP) has powerful dynamics and thermal effects, which makes the interaction between its land and atmosphere significantly affect climate and environment in the regional or global area. By retrospecting the latest research progress in the simulation of land-surface processes(LSPs) over the past 20 years, this study discusses both the simulation ability of land-surface models(LSMs) and the modification of parameterization schemes from two perspectives, the models' applicability and improved parameterization schemes. Our review suggests that different LSMs can well capture the spatiotemporal variations of the physical quantities of LSPs; but none of them can be fully applied to the plateau, meaning that all need to be revised according to the characteristics specific to the TP. Avoiding the unstable iterative computation and determining the freeze-thaw critical temperature according to the thermodynamic equilibrium equation, the unreasonable freeze-thaw parameterization scheme can be improved. Due to the complex underlying surface of the TP, no parameterization scheme of roughness length can well simulate the various characteristics of the turbulent flux over the TP at different temporal scales. The uniform soil thermodynamic and hydraulic parameterization scheme is unreasonable when it is applied to the plateau, as a result of the strong soil heterogeneity. There is little research on the snow-cover process so far,and the improved scheme has no advantage over the original one due to the lack of some related physical processes. The constant interaction among subprocesses of LSPs makes the improvement of a multiparameterization scheme yield better simulation results. According to the review of existing research, adding high-quality observation stations, developing a parameterization scheme suitable for the special LSPs of the TP, and adjusting the model structures can be helpful to the simulation of LSPs on the TP.

AN IMPROVED LAND-SURFACE PROCESS MODEL AND ITS SIMULATION EXPERIMENT——PART I:LAND-SURFACE PROCESS MODEL AND ITS“OFF-LINE”TESTS AND PERFORMANCE ANALYSES

Based on the existing land-surface schemes and models,an improved Land-surface Process Model(LPM-ZD)has been developed.It has the following major characteristics:(1)The combination of physical equations and empirical analytical formulae are used to construct the governing equations of soil temperature and moisture.Higher resolution of model level and physical equations are adopted for the upper soil layers,and for the lower soil layers,lower resolution of model level is adopted and empirical analytical formulae are used.(2)In land surface hydrological process,the sub-grid distribution of rainfall and its effects are taken into account. (3)A simple snow cover submodel has been used,which includes effects of snow cover on soil thermodynamics and hydrology,as well as albedo. By use of this model and three groups of point observation data,a series of“off-line”tests have been carried out.The simulation results indicate that land-surface process model has good performance and can well simulate diurnal and seasonal variation of land surface processes for many kinds of land surface covers(forest,grass,crops and desert)in different climate zone.The results simulated by the model are consistent with the observations.Later,by use of one group of observation data and the model,a series of sensitivity experiments have been done.It is shown that the model is much sensitive to some parameters,such as initial soil moisture,vegetation physical parameters as well as the proportion of the grid covered with rain.Therefore it is much important for land-surface process model to define these parameters as accurately as possible.

SOME NEW UNDERSTANDINGS OF LAND-SURFACE PROCESSES IN ARID AREA FROM THE HEIFE

The survey for the HEIFE(Atmosphere-Land Surface Processes Experiment at Heihe River Basin,Western China)is given in the paper.The following basic subjects for land-surface process- es in arid areas are studied:(1)the general characteristics of the energy budget on ground surface in arid areas;(2)the parameterization of the land surface processes;(3)the interaction between oasis and its desert circumstances,a special phenomenon in arid areas.The analysis shows that the sensible heat flux in the surface energy budget is in the majority,and the latent heat flux may be neglected.The influence of atmospheric stratification stability on the turbulent transfer of energy and substance must be considered in parameterization of land surface processes in arid areas.The “cold island effect”phenomenon in oasis and the“humidity inversion”phenomenon in desert near oasis are the result of the interaction between them.The results would improve the understanding of land surface processes in arid areas.

AN IMPROVED LAND-SURFACE PROCESS MODEL AND ITS SIMULATION EXPERIMENT—PART II:COUPLING SIMULATION EXPERIMENT OF LAND-SURFACE PROCESS MODEL WITH REGIONAL CLIMATE MODEL

The Land-surface Process Model(LPM-ZD)has been successfully coupled with the regional climate model RegCM2 of NCAR.Then thus-obtained coupled model(CRegCM)has been applied to simulate the climate characteristics of heavy rain in middle and East China for three months from May to July 1991.and compared with model output of NCAR-RegCM2 using BATS as land- surface process scheme,abbreviated as NRegCM.The results show that CRegCM has good ability and performance.CRegCM successfully simulates the extreme precipitation event and the simulations of CRegCM for surface temperature and some physical variables related to land surface process are more reasonable than those of NRegCM.

Dendritic spine degeneration:a primary mechanism in the aging process

Recent reports suggest that aging is not solely a physiological process in living beings;instead, it should be considered a pathological process or disease(Amorim et al., 2022). Consequently, this process involves a wide range of factors, spanning from genetic to environmental factors, and even includes the gut microbiome(GM)(Mayer et al., 2022). All these processes coincide at some point in the inflammatory process, oxidative stress, and apoptosis, at different degrees in various organs and systems that constitute a living organism(Mayer et al., 2022;AguilarHernández et al., 2023).

基于Arduino与Processing的心率检测计设计研究

随着社会经济的高速发展,人们的物质生活也有了极大的提高,但同时也伴随着各种疾病的到来,身体健康已经成为人们普遍关注的焦点,因此,心率检测仪、血压计、血糖仪等各种家用医疗监测仪器已经逐渐融入日常生活。心脏病是人们难以预防的突发致命疾病之一,本文介绍的是一款基于Arduino【是基于易用硬件和软件的原型开源平台,包由可编程的电路板(简称微控制器),以及集成开发环境(称为Arduino IDE)的现成软件组成】Processing(开源编程语言,包括编辑器、编译器、展示器)的简易心率检测计系统,其功能实用、操作简单,可以测量心率,当超出正常心率范围时及时预警,是一款便携的实时心率测试仪。

Comparative study of surface energy and land-surface parameters in different climate zones in Northwest China

Based on observational data of arid,semi-arid and semi-humid areas in Northwest China,the characteristics of surface-wa ter heat transfer and land-surface parameters were compared and analyzed.The results show that the annual mean net radi ation was largest in the semi-humid area,followed by the semi-arid area,and then the arid area:77.72 W/m^2,67.73 W/m^2,and 55.47 W/m^2,respectively.The annual mean sensible heat flux was largest in the arid area,followed by the semi-arid and semi-humid areas,while latent heat flux showed the reverse.The annual mean sensible heat flux in arid,semi-arid,and semi-humid areas was 85.7 W/m^2,37.59 W/m^2,and 27.55 W/m^2,respectively.The annual mean latent heat flux was 0 W/m^2,26.08 W/m^2,and 51.19 W/m2,respectively.The annual mean soil-heat flux at the 5-cm soil layer in arid,semi-arid,and semi-humid areas was 1.00 W/m^2,0.82 W/m^2,and 1.25 W/m^2,respectively.The annual mean surface albedo was larg est in the arid area,followed by the semi-humid area;and the smallest was in the semi-arid area:0.24,0.21,and 0.18,re spectively.The annual mean Bowen ratio in the semi-arid area was about 2.06,and that in semi-humid area was about 0.03.The annual mean soil thermal conductivity in the arid,semi-arid,and semi-humid areas was 0.26 W/(m k),1.15 W/(m k),and 1.20 W/(m k),respectively.

Comparison of different land-surface perturbation methods in short-range ensemble forecasts

In order to compare the sensitivity of short-range ensemble forecasts to different land-surface parameters in the South China region,three perturbation experiments related to the land surface model(LSM),initial soil moisture(ISM),and land–atmosphere coupling coefficient(LCC)were designed,and another control experiment driven by the Global Ensemble Forecast System(GEFS)was also performed.All ensemble members were initiated at 0000 UTC each day,and integrated for 24 h for a total of 40 days from the period 1 April to 10 May 2019 based on the Weather Research and Forecasting model.The results showed that the perturbation experiment of the LSM(LSMPE)had the largest ensemble spread,as well as the lowest ensemble-mean root-mean-square error among the three sets of land-surface perturbed experiments,which indicated that it could represent more uncertainty and less error.The ensemble spread of the perturbation experiment of the ISM(ISMPE)was generally less than that of LSMPE but greater than that of LCCPE(the perturbation experiment of the LCC).In particular,although the perturbation of the LCC could not produce greater spread,it had an effective influence on the intensity of precipitation.However,the ensemble spread of all the land-surface perturbed experiments was smaller than that of GEFSPE(the control experiment).Therefore,in future,land-surface perturbations and atmospheric perturbations should be combined in the design of ensemble forecasting systems to make the model represent more uncertainties.

MODIS-Derived Nighttime Arctic Land-Surface Temperature Nascent Trends and Non-Stationary Changes

Arctic nighttime land-surface temperatures derived by the Moderate Resolution Imaging Spectroradiometer (MODIS) sensors onboard the NASA Terra and Aqua satellites are investigated. We use the local equator crossing times of 22:30 and 01:30, respectively, in the analysis of changes, trends and variations on the Arctic region and within 120° sectors. We show increases in the number of days above 0°C and significant increase trends over their decadal periods of March 2000 through 2010 (MODIS Terra) and July 2002 through 2012 (MODIS Aqua). The MODIS Aqua nighttime Arctic land-surface temperature change, +0.2°C ± 0.2°C with P-value of 0.01 indicates a reduction relative to the MODIS Terra nighttime Arctic land-surface temperature change, +1.8°C ± 0.3°C with P-value of 0.01. This reduction is a decadal non-stationary component of the Arctic land-surface temperature changes. The reduction is greatest, -1.3°C ± 0.2°C with P-value of 0.01 in the Eastern Russia— Western North American sector of the Arctic during the July 2002 through 2012.

Constraints on Characteristics and Distribution of Gas Hydrate and Free Gas Using Broad-Band Processing of Three-Dimensional Seismic Data

Gas hydrate drilling expeditions in the Pearl River Mouth Basin,South China Sea,have identified concentrated gas hydrates with variable thickness.Moreover,free gas and the coexistence of gas hydrate and free gas have been confirmed by logging,coring,and production tests in the foraminifera-rich silty sediments with complex bottom-simulating reflectors(BSRs).The broad-band processing is conducted on conventional three-dimensional(3D)seismic data to improve the image and detection accuracy of gas hydratebearing layers and delineate the saturation and thickness of gas hydrate-and free gas-bearing sediments.Several geophysical attributes extracted along the base of the gas hydrate stability zone are used to demonstrate the variable distribution and the controlling factors for the differential enrichment of gas hydrate.The inverted gas hydrate saturation at the production zone is over 40% with a thickness of 90 m,showing the interbedded distribution with different boundaries between gas hydrate-and free gas-bearing layers.However,the gas hydrate saturation value at the adjacent canyon is 70%,with 30-m-thick patches and linear features.The lithological and fault controls on gas hydrate and free gas distributions are demonstrated by tracing each gas hydrate-bearing layer.Moreover,the BSR depths based on broad-band reprocessed 3D seismic data not only exhibit variations due to small-scale topographic changes caused by seafloor sedimentation and erosion but also show the upward shift of BSR and the blocky distribution of the coexistence of gas hydrate and free gas in the Pearl River Mouth Basin.

Design and optimization of a greener sinomenine hydrochloride preparation process considering variations among different batches of the medicinal herb

The current methods used to industrially produce sinomenine hydrochloride involve several issues,including high solvent toxicity,long process flow,and low atomic utilization efficiency,and the greenness scores of the processes are below 65 points.To solve these problems,a new process using anisole as the extractant was proposed.Anisole exhibits high selectivity for sinomenine and can be connected to the subsequent water-washing steps.After alkalization of the medicinal material,heating extraction,water washing,and acidification crystallization were carried out.The process was modeled and optimized.The design space was constructed.The recommended operating ranges for the critical process parameters were 3.0–4.0 h for alkalization time,60.0–80.0℃ for extraction temperature,2.0–3.0(volume ratio)for washing solution amount,and 2.0–2.4 mol·L^(-1) for hydrochloric acid concentration.The new process shows good robustness because different batches of medicinal materials did not greatly impact crystal purity or sinomenine transfer rate.The sinomenine transfer rate was about 20%higher than that of industrial processes.The greenness score increased to 90 points since the novel process proposed in this research solves the problems of long process flow,high solvent toxicity,and poor atomic economy,better aligning with the concept of green chemistry.

Investigation on taste characteristics and sensory perception of soft-boiled chicken during oral processing based on electronic tongue and electronic nose

The sensory perception of food is a dynamic process,which is closely related to the release of flavor substances during oral processing.It’s not only affected by the food material,but also subjected to the individual oral environment.To explore the oral processing characteristics of soft-boiled chicken,the sensory properties,texture,particle size,viscosity,characteristic values of electronic nose and tongue of different chicken samples were investigated.The correlation analysis showed that the physical characteristics especially the cohesiveness,springiness,resilience of the sample determined oral processing behavior.The addition of chicken skin played a role in lubrication during oral processing.The particle size of the bolus was heightened at the early stage,and the fluidity was enhanced in the end,which reduced the chewing time to the swallowing point and raised the aromatic compounds signal of electronic nose.But the effect of chicken skin on chicken thigh with relatively high fat content,was opposite in electronic nose,which had a certain masking effect on the perception of umami and sweet taste.In conclusion,fat played a critical role in chicken oral processing and chicken thigh had obvious advantages in comprehensive evaluation of soft-boiled chicken,which was more popular among people.

Toluene Processed All-Polymer Solar Cells with 18%Efficiency and Enhanced Stability Enabled by Solid Additive:Comparison Between Sequential-Processing and Blend-Casting

The emergence of polymerized small molecule acceptors(PSMAs)has significantly improved the performance of all-polymer solar cells(all-PSCs).However,the pace of device engineering lacks behind that of materials development,so that a majority of the PSMAs have not fulfilled their potentials.Furthermore,most high-performance all-PSCs rely on the use of chloroform as the processing solvent.For instance,the recent highperformance PSMA,named PJ1-γ,with high LUMO,and HOMO levels,could only achieve a PCE of 16.1%with a high-energy-level donor(JD40)using chloroform.Herein,we present a methodology combining sequential processing(SqP)with the addition of 0.5%wt PC_(71)BM as a solid additive(SA)to achieve an impressive efficiency of 18.0%for all-PSCs processed from toluene,an aromatic hydrocarbon solvent.Compared to the conventional blend-casting(BC)method whose best efficiency(16.7%)could only be achieved using chloroform,the SqP method significantly boosted the device efficiency using toluene as the processing solvent.In addition,the donor we employ is the classic PM6 that has deeper energy levels than JD40,which provides low energy loss for the device.We compare the results with another PSMA(PYF-T-o)with the same method.Finally,an improved photostability of the SqP devices with the incorporation of SA is demonstrated.

MODIS-Derived Arctic Land-Surface Temperature Trends

Across the Arctic changes in active layer, melting of glaciers and ground ice, thawing of permafrost and sequestration changes of carbon storage are driven in part by variations of land surface heat absorption, conduction and re-radiation relative to solar irradiance. We investigate Arctic land-surface temperature changes and regional variations derived by the MODIS sensors on NASA Aqua and Terra from March 2000 through July 2012. Over this decadal period we detect increase in the number of days with daytime land-surface temperature above 0℃. There are indications of increasing trends of land-surface temperature change. Regional variations of the changes in land-surface temperature likely arise due to surface material types and topography relative to the daytime variation of solar irradiance.

Study on the coupling calculation method for the launch dynamics of a self-propelled artillery multibody system considering engraving process

The launch dynamics theory for multibody systems emerges as an innovative and efficacious approach for the study of launch dynamics,capable of addressing the challenges of complex modeling,diminished computational efficiency,and imprecise analyses of system dynamic responses found in the dynamics research of intricate multi-rigid-flexible body systems,such as self-propelled artillery.This advancement aims to enhance the firing accuracy and launch safety of self-propelled artillery.Recognizing the shortfall of overlooking the band engraving process in existing theories,this study introduces a novel coupling calculation methodology for the launch dynamics of a self-propelled artillery multibody system.This method leverages the ABAQUS subroutine interface VUAMP to compute the dynamic response of the projectile and barrel during the launch process of large-caliber self-propelled artillery.Additionally,it examines the changes in projectile resistance and band deformation in relation to projectile motion throughout the band engraving process.Comparative analysis of the computational outcomes with experimental data evidences that the proposed method offers a more precise depiction of the launch process of self-propelled artillery,thereby enhancing the accuracy of launch dynamics calculations for self-propelled artillery.

Arctic Diurnal Land-Surface Temperature Range Changes Derived by NASA MODIS-Terra and -Aqua 2000 through 2012

The diurnal variation of surface temperature is a fundamental parameter as it is a driver of physical processes of atmosphere-land and -ocean energy and mass cycles playing a key role in meteorology and climatology. Our investigation focus is on the diurnal variation of land-surface temperature derived by the Moderate Resolution Imaging Spectroradiometer (MODIS) deployed on the NASA Terra and Aqua satellites. We key our investigation on the ascending and descending mode equator crossing times for daytime and nighttime land-surface temperature variations from March 2000 through 2010 (MODIS-Terra) and July 2002 through 2012 (MODIS-Aqua) and assess the diurnal land-surface temperature range changes at those sampling times. Our investigation shows non-stationary changes in the trends of land-surface temperature diurnal range. We identify changes in the diurnal range trends linked to increase of daytime and nighttime land-surface temperatures from March 2000 through 2010 and decrease in daytime and nighttime land-surface temperatures from July 2002 through 2012. The most recent decrease in daytime and nighttime land-surface temperatures and diurnal range will affect Arctic and other associated energy and mass cycles.

Effects of friction stir processing and nano-hydroxyapatite on the microstructure,hardness,degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications

Nowadays,magnesium alloys are emerging in biomedical implants for their similar properties to natural bones.However,the rapid degradation of magnesium alloys in biological media hinders successful implantation.Refinement of microstructure,as well as reinforcement particles can significantly improve the degradation rate.In this work,multi-pass friction stir processing(FSP)was proposed to synthesize WE43/nano-hydroxyapatite(n HA)surface composite,the microstructure,reinforced particle distribution,micro-hardness,corrosion behavior and in-vitro bioactivity were studied.The subsequent FSP passes of WE43 alloy and WE43/n HA composite refined the grain size which was reduced by 94.29%and 95.92%(2.63 and 1.88μm,respectively)compared to base metal after three passes.This resulted in increasing the microhardness by 120%(90.86 HV0.1)and 135%(105.59 HV0.1)for the WE43 and WE43-n HA,respectively.It is found that increasing FSP passes improved the uniform distribution of n HA particles within the composite matrix which led to improved corrosion resistance and less degradation rate.The corrosion rate of the FSPed WE43/n HA composite after three passes was reduced by 38.2%(4.13 mm/year)and the degradation rate was reduced by 69.7%(2.87 mm/y).This is attributed to secondary phase(Mg24Y5and Mg41Nd5)particle fragmentation and redistribution,as well as a homogeneous distribution of n HA.Additionally,the growing Ca-P and Mg(OH)2layer formed on the surface represented a protective layer that reduced the degradation rate.The wettability test revealed a relatively hydrophilic surface with water contact angle of 49.1±2.2°compared to 71.2±2.1°for base metal.Also,biomineralization test showed that apatite layer grew after immersion 7d in simulated body fluid with atomic ratio of Ca/P 1.60 approaching the stoichiometric ratio(1.67)indicating superior bioactivity of FSPed WE43/n HA composite after three passes.These results raise that the grain refinement by FSP and introduction of n HA particles significantly improved the degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications.

A new insight into LPSO phase transformation and mechanical properties uniformity of large-scale Mg-Gd-Y-Zn-Zr alloy prepared by multi-pass friction stir processing

A large-scale fine-grained Mg-Gd-Y-Zn-Zr alloy plate with high strength and ductility was successfully prepared by multi-pass friction stir processing(MFSP)technology in this work.The structure of grains and long period stacking ordered(LPSO)phase were characterized,and the mechanical properties uniformity was investigated.Moreover,a quantitative relationship between the microstructure and tensile yield strength was established.The results showed that the grains in the processed zone(PZ)and interfacial zone(IZ)were refined from 50μm to 3μm and 4μm,respectively,and numerous original LPSO phases were broken.In IZ,some block-shaped 18R LPSO phases were transformed into needle-like 14H LPSO phases due to stacking faults and the short-range diffusion of solute atoms.The severe shear deformation in the form of kinetic energy caused profuse stacking fault to be generated and move rapidly,greatly increasing the transformation rate of LPSO phase.After MFSP,the ultimate tensile strength,yield strength and elongation to failure of the large-scale plate were 367 MPa,305 MPa and 18.0% respectively.Grain refinement and LPSO phase strengthening were the major strengthening mechanisms for the MFSP sample.In particularly,the strength of IZ was comparable to that of PZ because the strength contribution of the 14H LPSO phase offsets the lack of grain refinement strengthening in IZ.This result opposes the widely accepted notion that IZ is a weak region in MFSP-prepared large-scale fine-grained plate.

Recent developments in selective laser processes for wearable devices

Recently,the increasing interest in wearable technology for personal healthcare and smart virtual/augmented reality applications has led to the development of facile fabrication methods.Lasers have long been used to develop original solutions to such challenging technological problems due to their remote,sterile,rapid,and site-selective processing of materials.In this review,recent developments in relevant laser processes are summarized under two separate categories.First,transformative approaches,such as for laser-induced graphene,are introduced.In addition to design optimization and the alteration of a native substrate,the latest advances under a transformative approach now enable more complex material compositions and multilayer device configurations through the simultaneous transformation of heterogeneous precursors,or the sequential addition of functional layers coupled with other electronic elements.In addition,the more conventional laser techniques,such as ablation,sintering,and synthesis,can still be used to enhance the functionality of an entire system through the expansion of applicable materials and the adoption of new mechanisms.Later,various wearable device components developed through the corresponding laser processes are discussed,with an emphasis on chemical/physical sensors and energy devices.In addition,special attention is given to applications that use multiple laser sources or processes,which lay the foundation for the all-laser fabrication of wearable devices.