Key Techniques of High-voltage and Large-capacity Series Hybrid Active Power Filters

基于基波磁通补偿的串联混合型有源电力滤波器（active power filter,APF）应用于高电压、大容量的谐波抑制场合时,受变压器励磁支路谐波电压的影响,逆变器不能等效为基波电流源,其输出电流将含有大量的谐波,从而影响滤波效果。以逆变器为核心,推导出在励磁支路谐波压降影响下的串联变压器的谐波等效阻抗。并以此为基础,从理论上分析励磁电感和变比对串联变压器谐波等效阻抗和APF滤波效果的影响。仿真结果验证了理论分析的正确性。最后,针对广东某厂10kV、1MVA电力负荷,研制一套基于基波磁通补偿的串联混合型有源滤波器工程样机,取得非常好的滤波效果。

Effectively Modulating Oxygen Vacancies in Flower‑Likeδ‑MnO_(2)Nanostructures for Large Capacity and High‑Rate Zinc‑Ion Storage

In recent years,manganese-based oxides as an advanced class of cathode materials for zinc-ion batteries(ZIBs)have attracted a great deal of attentions from numerous researchers.However,their slow reaction kinetics,limited active sites and poor electrical conductivity inevitably give rise to the severe performance degradation.To solve these problems,herein,we introduce abundant oxygen vacancies into the flower-likeδ-MnO_(2)nanostructure and effectively modulate the vacancy defects to reach the optimal level(δ-MnO_(2)-x-2.0).The smart design intrinsically tunes the electronic structure,guarantees ion chemisorption-desorption equilibrium and increases the electroactive sites,which not only effectively accelerates charge transfer rate during reaction processes,but also endows more redox reactions,as verified by first-principle calculations.These merits can help the fabricatedδ-MnO_(2)-x-2.0 cathode to present a large specific capacity of 551.8 mAh g^(-1) at 0.5 A g^(-1),high-rate capability of 262.2 mAh g^(-1) at 10 A g^(-1) and an excellent cycle lifespan(83%of capacity retention after 1500 cycles),which is far superior to those of the other metal compound cathodes.In addition,the charge/discharge mechanism of theδ-MnO_(2)-x-2.0 cathode has also been elaborated through ex situ techniques.This work opens up a new pathway for constructing the next-generation high-performance ZIBs cathode materials.

A Novel Soft Start Method of Super Large Capacity High Voltage Motor

The large current generated by starting directly of super large capacity and high voltage induction motor would have a huge impact on the grid as well as the motor itself.The variation of the power factor and electromagnetic torque during direct start of motors with different capacity and voltage levels are obtained.Aiming at the problem that the secondary impact of auto-transformer starter is too large and the cost of magnetic control starter is too high,the auto-transformer and magnetic control soft start method of super large capacity and high voltage motor is proposed and the basic working principle is analyzed.The calculation formula of cost for magnetic control soft starter and auto-transformer and magnetic control soft starter is deduced,and specific examples are analyzed and compared.It is concluded that the choice of auto-transformer with appropriate tapping ratio can greatly reduce the cost of auto-transformer and magnetic control soft starter compared with the other one.Finally,the simulation and experiment results show that the start method can effectively avoid secondary current impact and constrain the motor starting current to less than 2.5 times the rated current.

Constructing Large Capacity Power Plant on Collapsible Loess Stratum with Huge Thickness

1 Preface In the northern and northwestern parts of China, quite a large portion of area, approximately 630,000 km^2, is covered by loess and loess-liked soils. The loess thickness ranges from several meters to several hundred meters along the river’s terraces to those geomorphologic plateaus. In geology, "China Loess" has become a geologic term, because the loess in China has evolved with the widest distribution and greatest thickness in the world, and is also a typical and significant deposit in Quaternary Period.

Prospective TRV Calculation of Large Capacity Parallel Breaking Based on High Coupled Split Reactor

With the increasing short-circuit power of system,it is an effective way to solve the large capacity of short-circuit breaking by using parallel breaking technology which composed by a high coupling splitter reactor and two parallel breakers in series.According to research the TRV equivalent calculation circuit and initial conditions in equal current mode and limit current mode respectively,the prospective TRV of CB1and CB2have been calculated for rated voltage of 252 kV and rated short-circuit current of85 k A.The results indicate that TRV of CB1and CB2are not affected by high split coupled reactor in equal current interruption mode,and TRV of CB1is under the standard requirement values after first current zero crossing and the TRV of CB2is exceed the standard requirement values after second current zero crossing which is also higher than the ITRV and line-side TRV of SLF in limit current interruption mode.Furthermore,the research conclusions of this paper can provide the theory and reference basis for parallel breaking technology.

Two-Dimensional Large Deformation Finite Element Analysisfor the Pulling-up of Plate Anchor

Based on mesh regeneration and stress interpolation from an old mesh to a new one, a large deformation finite element model is developed for the study of the behaviour of circular plate anchors subjected to uplift loading. For the deterruination of the distributions of stress components across a clay foundation, the Recovery by Equilibrium in Patches is extended to plastic analyses. ABAQUS, a commercial finite element package, is customized and linked into our program so as to keep automatic and efficient running of large deformation calculation. The quality of stress interpolation is testified by evaluations of Tresca stress and nodal reaction forces. The complete pulling-up processes of plate anchors buried in homogeneous clay arc simulated, and typical pulling force-displacement responses of a deep anchor and a shallow anchor are compared. Different from the results of previous studies, large deformation analysis is of the capability of estimating the breakaway between the anchor bottom and soils. For deep anchors, the variation of mobilized uplift resistance with anchor settlement is composed of three stages, and the initial buried depths of anchors affect the separation embedment slightly. The uplift bearing capacity of deep anchors is usually higher than that of shallow anchors.

Key technologies and equipment for a fully mechanized top-coal caving operation with a large mining height at ultra-thick coal seams

Thick and ultra-thick coal seams are main coal seams for high production rate and high efficiency in Chinese coal mines, which accounts for 44 % of the total minable coal reserve. A fully mechanized top-coal caving mining method is a main underground coal extraction method for ultra-thick coal seams. The coal extraction technologies for coal seams less than 14 m thick were extensively used in China. However, for coal seams with thickness greater than 14 m, there have been no reported cases in the world for underground mechanical extraction with safe performance, high efficiency and high coal recovery ratio. To deal with this case, China Coal Technology ＆ Engineering Group, Datong Coal Mine Group, and other 15 organizations in China launched a fundamental and big project to develop coal mining technologies and equipment for coal seams with thicknesses greater than 14 m. After the completion of the project, a coal extraction method was developed for top-coal caving with a large mining height, as well as a ground control theory for ultra-thick coal seams. In addition, the mining technology for top-coal caving with a large mining height, the ground support technology for roadway in coal seams with a large cross-section, and the prevention and control technology for gas and fire hazards were developed and applied. Furthermore, a hydraulic support with a mining height of 5.2 m, a shearer with high reliability, and auxiliary equipment were developed and manufactured. Practical implication on the technologies and equipment developed was successfully completed at the No. 8105 coal face in the Tashan coal mine, Datong, China. The major achievements of the project are summarized as follows： 1. A top-coal caving method for ultra-thick coal seams is proposed with a cutting height of 5 m and a top-coal caving height of 15 m. A structural mechanical model of overlying strata called cantilever beam-articulated rock beam is established. Based on the model, the load resistance of the hydraulic support with a large mining height for top-coal caving method is determined. With the analysis, the movement characteristics of the top coal and above strata are evaluated during top-coal caving operation at the coal face with a large mining height. Furthermore, there is successful development of comprehensive technologies for preventing and controlling spalling of the coal wall, and the top-coal caving technology with high efficiency and high recovery at the top-coal caving face with a large mining height. This means that the technologies developed have overcome the difficulties in strata control, top-coal caving with high efficiency and high coal recovery, and enabled to achieve a production rate of more than 10 Mtpa at a single top-coal caving face with a large mining height in ultra-thick coal seams; 2. A hydraulic support with 5.2 m supporting height and anti-rockburst capacity, a shearer with high reliability, a scraper conveyor with a large power at the back of face, and a large load and long distance headgate belt conveyor have been successfully developed for a top-coal caving face with large mining height. The study has developed the key technologies for improving the reliability of equipment at the coal face and has overcome the challenges in equipping the top-coal caving face with a large mining height in ultra-thick coal seams; 3. The deformation characteristics of a large cross-section roadway in ultra-thick coal seams are discovered. Based on the findings above, a series of bolt materials with a high yielding strength of 500-830 MPa and a high extension ratio, and cable bolt material with a 1 × 19 structure, large tonnage and high extension ratio are developed. In addition, in order to achieve a safe roadway and a fast face advance, installation equipment for high pre-tension bolt is developed to solve the problems with the support of roadway in coal seams for top-coal caving operation with a large mining height; 4. The characteristics of gas distribution and uneven emission at top-coal caving face with large mining height in ultra-thick coal seams are evaluated. With the application of the technologies of gas drainage in the roof, the difficulties in gas control for high intensive top-coal caving mining operations, known as ＂low gas content, high gas emission＂, are solved. In addition, large flow-rate underground mobile equipment for making nitrogen are developed to solve the problems with fire prevention and safe mining at a top-coal caving face with large mining height and production rate of more than 10 Mtpa. A case study to apply the developed technologies has been conducted at the No. 8105 face, the Tashan coal mine in Datong, China. The case study demonstrates that the three units of equipment, i.e., the support, shearer and scraper conveyor, are rationally equipped. Average equipment usage at the coal face is 92.1%. The coal recovery ratio at the coal face is up to 88.9 %. In 2011, the coal production at the No. 8105 face reached 10.849 Mtpa, exceeding the target of 10 Mtpa for a topcoal caving operation with large mining height performed by Chinese-made mining equipment. The technologies and equipment developed provide a way for extracting ultra-thick coal seams. Currently, the technologies and equipment are used in 13 mining areas in China including Datong, Pingshuo, Shendong and Xinjiang. With the exploitation of coal resources in Western China, there is great potential for the application of the technologies and equipment developed.

Large Eddy Simulations of Flow Instabilities in a Stirred Tank Gen-erated by a Rushton Turbine

The aim of this work is to investigate the flow instabilities in a baffled, stirred tank generated by a single Rushton turbine by means of large eddy simulation （LES）. The sliding mesh method was used for the coupling between the rotating and the stationary frame of references. The calculations were carried out on the ＂Shengcao-21C＂ supercomputer using a computational fluid dynamics （CFD） code CFX5. The flow fields predicted by the LES simulation and the simulation using standard κ-ε model were compared to the results from particle image velocimetry （PIV） measurements. It is shown that the CFD simulations using the LES approach and the standard κ-ε model agree well with the PIV measurements. Fluctuations of the radial and axial velocity are predicted at different frequencies by the LES simulation. Velocity fluctuations of high frequencies are seen in the impeller region, while low frequencies velocity fluctuations are observed in the bulk flow. A low frequency velocity fluctuation with a nondimensional frequency of 0.027Hz is predicted by the LES simulation, which agrees with experimental investigations in the literature. Flow circulation patterns predicted by the LES simulation are asymmetric, stochastic and complex, spanning a large portion of the tanks and varying with time, while circulation patterns calculated by the simulation using the standard κ-ε model are symmetric. The results of the present work give better understanding to the flow instabilities in the mechanically agitated tank. However, further analysis of the LES calculated velocity series by means of fast Fourier transform （FFT） and/or spectra analysis are recommended in future work in order to gain more knowledge of the complicated flow phenomena.

Formation conditions and exploration direction of large natural gas reservoirs in the oil-prone Bohai Bay Basin, East China

The Bohai Bay Basin is a typical oil-prone basin, in which natural gas geological reserves have a small proportion. In this basin, the gas source rock is largely medium-deep lake mudstone with oil-prone type Ⅱ2-Ⅱ1 kerogens, and natural gas preservation conditions are poor due to active late tectonic movements. The formation conditions of large natural gas fields in the Bohai Bay Basin have been elusive. Based on the exploration results of Bohai Bay Basin and comparison with large gas fields in China and abroad, the formation conditions of conventional large-scale natural gas reservoirs in the Bohai Bay Basin were examined from accumulation dynamics, structure and sedimentation. The results show that the formation conditions of conventional large natural gas reservoirs in Bohai Bay Basin mainly include one core element and two key elements. The core factor is the strong sealing of Paleogene "quilt-like" overpressure mudstone. The two key factors include the rapid maturation and high-intensity gas generation of source rock in the late stage and large scale reservoir. On this basis, large-scale nature gas accumulation models in the Bohai Bay Basin have been worked out, including regional overpressure mudstone enriching model, local overpressure mudstone depleting model, sand-rich sedimentary subsag depleting model and late strongly-developed fault depleting model. It is found that Bozhong sag, northern Liaozhong sag and Banqiao sag have favorable conditions for the formation of large-scale natural gas reservoirs, and are worth exploring. The study results have important guidance for exploration of large scale natural gas reservoirs in the Bohai Bay Basin.

Effect of Tip-Blade Cutting on the Performance of Large Scale Axial Fan

The effect of tip-blade cutting on the performance of a large scale axial fan was investigated using computational fluid dynamics(CFD)methods.Experiments verified the numerical simulations.The original fan was compared with the one with tip-cutting in terms of dimensionless characteristic and aerodynamic performance in tip region under the conditions of the maximum efficiency point and near-stall point.The results showed that double leakage flow occurred in tip clearance at maximum efficiency point and spillage of leakage flow from leading edge occurred in tip-blade region at near-stall point for the both two fans;and that tip-cutting with 6% of blade height could reduce the intensity of tip-leakage vortex and increase flow capacity in tip blade region,and hold the stall margin almost the same as the original fan.The maximum efficiency of the fan with tip-cutting was improved by1%,and the ability of total pressure rising was obviously greater than the original fan.

Large deflections of non-prismatic nonlinearly elastic cantilever beams subjected to non-uniform continuous load and a concentrated load at the free end

This work studies large deflections of slen- der, non-prismatic cantilever beams subjected to a combined loading which consists of a non-uniformly distributed con- tinuous load and a concentrated load at the free end of the beam. The material of the cantilever is assumed to be non- linearly elastic. Different nonlinear relations between stress and strain in tensile and compressive domain are considered. The accuracy of numerical solutions is evaluated by com- paring them with results from previous studies and with a laboratory experiment.

Large System Analysis of Downlink C-RAN with Phase Noise and Fronthaul Compression

This paper studies the effect of phase noise and fronthaul compression on a downlink cloud radio access network(C-RAN), where several remote radio heads(RRHs) are coordinated to communicate with users by a baseband unit(BBU) on the cloud server. In the system, the baseband signals are precoded at BBU, and then compressed before being transmitted to RRHs through capacity-limited fronthaul links which results in the compressive quantization noise. We assume the regularized zero-forcing precoding is performed with an imperfect channel state information and a compression strategy is applied at BBU. The effect of phase noise arising from nonideal local oscillators both at RRHs and users is considered. We propose an approximate expression for the downlink ergodic sum-rate of considered C-RAN utilizing large dimensional random matrix theory in the large-system regime. From simulation results, the accuracy of the approximate expression is validated, and the effect of phase noise and fronthaul compression can be analyzed theoretically based on the approximate expression.

Investigation on some key problems of large power AC-DC-AC converter

China is an important country in iron and steel industry.Power electronics converters are widely used.For the cold rolling mills of high speed,AC-DC-AC converters should be used.In the paper,the design and the control system of the large power three-level AC - DC - AC converter with IGCTs is investigated,and a back-to-back large power three-level AC - DC - AC converter with IGCTs has been got. With a series experiments,the performance of the converter is examined.The experiment result indicates the converter reaches the design requirement and it shows excellent performance.The converter system has been put into use safely.It is estimated that the AC - DC - AC converter system will be used in the drive systems for rolling mills in the near future.

North slope transition zone of Songnan-Baodao sag in Qiongdongnan Basin and its control on medium and large gas fields,South China Sea

Based on analysis of newly collected 3D seismic and drilled well data,the geological structure and fault system of Baodao sag have been systematically examined to figure out characteristics of the transition fault terrace belt and its control on the formation of natural gas reservoirs.The research results show that the Baodao sag has the northern fault terrace belt,central depression belt and southern slope belt developed,among them,the northern fault terrace belt consists of multiple transition fault terrace belts such as Baodao B,A and C from west to east which control the source rocks,traps,reservoirs,oil and gas migration and hydrocarbon enrichment in the Baodao sag.The activity of the main fault of the transition belt in the sedimentary period of Yacheng Formation in the Early Oligocene controlled the hydrocarbon generation kitchen and hydrocarbon generation potential.From west to east,getting closer to the provenance,the transition belt increased in activity strength,thickness of source rock and scale of delta,and had multiple hydrocarbon generation depressions developed.The main fault had local compression under the background of tension and torsion,giving rise to composite traps under the background of large nose structure,and the Baodao A and Baodao C traps to the east are larger than Baodao B trap.Multiple fault terraces controlled the material source input from the uplift area to form large delta sand bodies,and the synthetic transition belt of the west and middle sections and the gentle slope of the east section of the F12 fault in the Baodao A transition belt controlled the input of two major material sources,giving rise to a number of delta lobes in the west and east branches.The large structural ridge formed under the control of the main fault close to the hydrocarbon generation center allows efficient migration and accumulation of oil and gas.The combination mode and active time of the main faults matched well with the natural gas charging period,resulting in the hydrocarbon gas enrichment.Baodao A transition belt is adjacent to Baodao 27,25 and 21 lows,where large braided river delta deposits supplied by Shenhu uplift provenance develop,and it is characterized by large structural ridges allowing high efficient hydrocarbon accumulation,parallel combination of main faults and early cessation of faulting activity,so it is a favorable area for hydrocarbon gas accumulation.Thick high-quality gas reservoirs have been revealed through drilling,leading to the discovery of the first large-scale gas field in Baodo 21-1 of Baodao sag.This discovery also confirms that the north transition zone of Songnan-Baodao sag has good reservoir forming conditions,and the transition fault terrace belt has great exploration potential eastward.

Decentralized Stabilization of Large-scale Uncertain Systems with State-Delays——LMIs Approach

This paper deals with the problem of decentralized robustcontrol for a class of interconnected uncertain systemswith state delays.The parameter uncertainties are un-known but norm-bounded.A new sufficient condition isobtained for each subsystem and overall system to be sta-bilizable via linear memoryless state feedback robust de-centralized controllers.The results depend on the size of the delays and are given in terms of linear matrix ine-qualities,so they are less conservative than those of delay-independent.Moreover,matching condition is not a necessary condition.Finally,an example is presented to illustrative the effectiveness of the proposed method.

Utilization Survey of Livestock Manure Resources in Large-scale Farms of Yangzhou

Based on surveying the conditions of large -scale farms and commercial manure in the each county of Yangzhou city, the situations and problems for utilization of livestock manure resources were grasped. After an analysis of the potential value of livestock manure, the suggestion and strategy for utilization of livestock manure resources were proposed based on the actual conditions in Yangzhou city.

A superhigh discharge capacity induced by a synergetic effect between high-surface-area carbons and a carbon paper current collector in a lithium–oxygen battery

This paper invesitages the synergetic effect between high-surface-area carbons, such as Ketjan Black(KB) or Super P(SP) carbon materials, and low-surface-area carbon paper(CP) current collectors and it also examines their influence on the discharge performance of nonaqueous Li–O2cells. Ultra-large specific discharge capacities are found in the KB/CP cathodes, which are much greater than those observed in the individual KB or CP cathodes. Detailed analysis indicates that such unexpectedly large capacities result from the synergetic effect between the two components. During the initial discharges of KB or SP materials, a large number of superoxide radical(O·-2) species in the electrolytes and Li2O2 nuclei at the CP surfaces are formed, which activate the CP current collectors to contribute considerable capacities. These results imply that CP could be a superior material for current collectors in terms of its contribution to the overall discharge capacity.On the other hand, we should be careful to calculate the specific capacities of the oxygen cathodes when using CP as a current collector; i.e., ignoring the contribution from the CP may cause overstated discharge capacities.

Performance of a Large-Scale Medical Waste Incinerator in a Referral Hospital

The aim of the study was to analyze the performance of large scale incinerator installed in a referral hospital. The study involved weighing and loading infectious waste of different composition (sharps and other waste), recording temperatures in the primary and secondary chamber with time, fuel used and collecting and weighing the bottom ash for 65 days. The analysis shows that the incinerator on average uses 362 L/day (45 L/h) to incinerate 945 kg of medical waste (40.8 kg/day of sharps waste and 904 kg/day of other waste), generating 51.2 kg of ash daily. The observed fuel consumption rate was too high necessitating corrective action. The average weight reduction was 94.6%. The study shows that the average sharps waste composition for medical waste incinerated was 4.3% and other waste was 95.7%. The incinerator capacity ranged between 100 and 130 kg/h. The fuel effectiveness ranged between 2.0 and 3.0 liters of diesel per kg of waste incinerated. The fuel effectiveness increased linearly with total waste incinerated and incinerator capacity, respectively, depending on the fuel consumption rate.