Dynamic response characteristics of super high-rise buildings subjected to long-period ground motions

Spectrum characteristics of different types of seismic waves and dynamic response characteristics of super high-rise building structures under long-period ground motions were comparatively analyzed. First, the ground response wave （named LS-R wave） of a soft soil site with deep deposit, taking long-period bedrock seismic record as input, was calculated by wave propagation method. After that, a TOMAKOMAI station long-period seismic record from the Tokachi-Oki earthquake and conventional E1-Centro wave were also chosen. Spectrum characteristics of these waves were analyzed and compared. Then, a series of shaking table tests were performed on a 1：50 scale super high-rise structural model under these seismic waves. Furthermore, numerical simulation of the prototype structure under these excitations was conducted, and structure damages under different intensive ground motions were discussed. The results show that： 1） Spectrum characteristics of ground response wave are significantly influenced by soft soil site with deep deposit, and the predominant period has an increasing trend. 2） The maximum acceleration amplification factor of the structure under the TOM wave is two times that under the E1-Centro wave; while the maximum displacement response of the structure under the TOM wave is 4.4 times that under the E1-Centro wave. Long-period ground motions show greater influences on displacement responses than acceleration responses for super high-rise building structures. 3） Most inelastic damage occurs at the upper 1/3 part of the super high-rise building when subjected to long-period ground motions.

Effects of high modes on the wind-induced response of super high-rise buildings

For super high-rise buildings, the vibration period of the basic mode is several seconds, and it is very close to the period of the fluctuating wind. The damping of super high-rise buildings is low, so super high-rise buildings are very sensitive to fluctuating wind. The wind load is one of the key loads in the design of super high-rise buildings. It is known that only the basic mode is needed in the wind-response analysis of tall buildings. However, for super high-rise buildings, especially for the acceleration response, because of the frequency amplification of the high modes, the high modes and the mode coupling may need to be considered. Three typical super high-rise projects with the SMPSS in wind tunnel tests and the random vibration theory method were used to analyze the effect of high modes on the wind-induced response. The conclusions can be drawn as follows. First, for the displacement response, the basic mode is dominant, and the high modes can be neglected. Second, for the acceleration response, the high modes and the mode coupling should be considered. Lastly, the strain energy of modes can only give the vibration energy distribution of the high-rise building, and it cannot describe the local wind-induced vibration of high-rise buildings, especially for the top acceleration response.

One potential superlarge Pb-Zn ore occurrence with Himalayan thermal brine genesis——Wuqia Region, Xinjiang, China

The paper focuses on geological and geochemical evidence of thermal brine genesis of Pb Zn deposits in Wuqia district, Xinjiang. The results suggest that the known Pb Zn deposits, such as Wulagen, are thermal brine genesis, which is supported by the features of tectonic setting, magma and regional metamorphism, and the characteristics of trace element distribution in strata and redistribution in the ore forming process, the REE patterns and their main parameters of main type ores, the composition features and the source indicators of Pb, S isotopes. Ore forming conditions of superlarge Pb Zn deposits studies show that there exists tectonic and sources setting of Jinding type superlarge Pb Zn deposits in this area. Five Pb Zn ore belts and central uplift belts discovered lately have not only confirmed that the genesis of Wulagen Pb Zn deposits is thermal genesis, but also further proved that there exists tectonic and source setting of Jinding type superlarge Pb Zn deposit in the study area. Mineral deposit model was described and prospecting potentiality of superlarge Pb Zn deposit and their significance were discussed.

New Zircon U-Pb Age of the Super-Large Lijiagou Spodumene Deposit in Songpan Garze Fold Belt, Eastern Tibet： Implications for Early Jurassic Rare-Metal Polymetallic Event

Objective The Songpan-Garze Fold Belt(SGFB),located in the eastern part of the Tibet Plateau and west of the Sichuan Basin,is an important pegmatite province in China.Some famous pegmatite type deposits occur in the SGFB,including the Xuebaoding,Jiajika,Keeryin rare metal deposits and Danba muscovite deposit(Li Jiankang et al.,2015).The newly discovered super-large Lijiagou

A Super-Large Rb-Nb Rare Metal Deposit has been Discovered in Huashi Village of Xinglong County, Hebei Province

Objective The Huashi Village in Xinglong County of Hebei Province is located in the Yanshan subsidence zone in the central eastern North China Plate, which is 137 km away from Beijing City （Fig. la）. This area has undergone large -scale magmatic intrusion affected by the tectonic compression of the Pacific Plate in the Mesozoic （known as the Yanshanian movement） to form many alkaline rocks such as the Wulingshan rock mass. Previous studies have conducted petrological research and reconnaissance survey of rare metal ores in this area （Tian Shuzhang and Guo Zongshan, 1981; Xu Baoling et al., 1996）. In 2016, the Qinhuangdao Mineral and Hydrology Engineering Geological Brigade of Hebei Bureau of Geology and Mineral Resources Exploration implemented the project of Reconnaissance of Rare Metal Ores Including Rubidium in Huashi Village of Xinglong County, Hebei Province, and discovered super-large rare metal deposits of rubidium and biobium in the Madi alkali feldspar granite bodies in the Huashi Village to achieve great breakthrough of rare metal ore prospecting.

Numerical analysis of ice accretion effects at super-cooled large droplet conditions on airfoil aerodynamics

Changes in flow field around NACA23012 airfoil from a clean condition to a super-cooled large droplet （SLD） condition were simulated, and variations in aerodynamic parameters were calculated using FLUENT. In the case of numerical simulation for a clean airfoil, flow field characteristics simulated agreed well with theory analysis, indicating that turbulence models and parameters setting are feasible. Aerodynamic parameters for iced airfoil were calculated using the same method and agreed with those measured test data under the same environment in icing wind tunnels by S. Lee. Conclusion is made that the numerical simulation is valid, and it can be an alternative to study ice accretion effects at the SLD condition on airfoil aerodynamics, leading to reduction in research cycle time and cost.

Discussion on the Construction of Anti-smoke Construction Technology in Super High-rise Buildings

In recent years with the increasing number of super high-rise buildings and the ever-expanding scale the anti-smoke construction technology has attracted more and more attention.Based on this situation,this paper analyzes the smoke control technology of super high-rise buildings.The paper analyzes the importance of the application of anti-smoke construction technology in super high-rise buildings,analyzes the problems in the construction of smoke control and super high-rise buildings.The anti-smoke construction technology was studied and I hope that it can benefit the application of anti-smoke construction technology in high-rise buildings.

The Major Ore Clusters of Super-Large Iron Deposits in the World, Present Situation of Iron Resources in China, and Prospect

The metamorphosed sedimentary type of iron deposits（BIF） is the most important type of iron deposits in the world, and super-large iron ore clusters of this type include the Quadrilatero Ferrifero district and Carajas in Brazil, Hamersley in Australia, Kursk in Russia, Central Province of India and Anshan-Benxi in China. Subordinated types of iron deposits are magmatic, volcanic-hosted and sedimentary ones. This paper briefly introduces the geological characteristics of major super-large iron ore clusters in the world. The proven reserves of iron ores in China are relatively abundant, but they are mainly low-grade ores. Moreover, a considerate part of iron ores are difficult to utilize for their difficult ore dressing, deep burial or other reasons. Iron ore deposits are relatively concentrated in 11 metallogenic provinces（belts）, such as the Anshan-Benxi, eastern Hebei, Xichang-Central Yunnan Province and middle-lower reaches of Yangtze River. The main minerogenetic epoches vary widely from the Archean to Quaternary, and are mainly the Late Archean to Middle Proterozoic, Variscan, and Yanshanian periods. The main 7 genetic types of iron deposits in China are metamorphosed sedimentary type（BIF）, magmatic type, volcanic-hosted type, skarn type, hydrothermal type, sedimentary type and weathered leaching type. The iron-rich ores occur predominantly in the skarn and marine volcanic-hosted iron deposits, locally in the metamorphosed sedimentary type（BIF） as hydrothermal reformation products. The theory of minerogenetic series of mineral deposits and minerogenic models has applied in investigation and prospecting of iron ore deposits. A combination of deep analyses of aeromagnetic anomalies and geomagnetic anomalies, with gravity anomalies are an effective method to seeking large and deep-buried iron deposits. China has a relatively great oresearching potential of iron ores, especially for metamorphosed sedimentary, skarn, and marine volcanic-hosted iron deposits. For the lower guarantee degree of iron and steel industry, China should give a trading and open the foreign mining markets.

A Novel Soft Start Method of Super Large Capacity High Voltage Motor

The large current generated by starting directly of super large capacity and high voltage induction motor would have a huge impact on the grid as well as the motor itself.The variation of the power factor and electromagnetic torque during direct start of motors with different capacity and voltage levels are obtained.Aiming at the problem that the secondary impact of auto-transformer starter is too large and the cost of magnetic control starter is too high,the auto-transformer and magnetic control soft start method of super large capacity and high voltage motor is proposed and the basic working principle is analyzed.The calculation formula of cost for magnetic control soft starter and auto-transformer and magnetic control soft starter is deduced,and specific examples are analyzed and compared.It is concluded that the choice of auto-transformer with appropriate tapping ratio can greatly reduce the cost of auto-transformer and magnetic control soft starter compared with the other one.Finally,the simulation and experiment results show that the start method can effectively avoid secondary current impact and constrain the motor starting current to less than 2.5 times the rated current.

Metallogenic mechanisms of super-large Cu and Au deposits in the Dexing region and simulating experiments

Based on the results of previous studies and under the direction of the theory of "ore deposit genesis",the authors made use of high temperature and high pressure experimental facilities and conditions at the Tectono-geochemistry Research Room under the State Key Laboratory of Ore Deposit Geochemistry,Institute of Geochemistry,Chinese Academy of Sciences,and put the focus on the multi-source of tectonically controlling ore-forming materials,the characteristics of multi-stage and multi-episode hydrothermal activities and mineralization and the characteristics of multi-genesis and multi-ore deposition so as to shed light on the metallogenic mechanisms of super-large Cu and Au deposits.In addition simulating experiments were made on multi-stage and multi-episode tectonic activities and rock and ore deformation,multi-stage and multi-episode tectonic activities and mobilization and migration of ore-forming materials,and multi-stage and multi-episode tectonic activities and superimposition and enrichment of ore-forming materials.The experimental results showed that under the action of multi-stage and multi-episode tectonic stress the deformation and fragmentation of not only rocks and ores have been intensified,and but also the ore-forming materials originally disbursed in the rocks and ores have been mobilized and migrated and superimposed and enriched.The experimental results also provided the scientific experimental data and grounds for deep-going research on the rules of metallogenesis and geneses of super-large ore deposits in the Dexing region,Jiangxi Province.

Intelligent optimization of the structure of the large section highway tunnel based on improved immune genetic algorithm

As in the building of deep buried long tunnels,there are complicated conditions such as great deformation,high stress,multi-variables,high non-linearity and so on,the algorithm for structure optimization and its application in tunnel engineering are still in the starting stage. Along with the rapid development of highways across the country,it has become a very urgent task to be tackled to carry out the optimization design of the structure of the section of the tunnel to lessen excavation workload and to reinforce the support. Artificial intelligence demonstrates an extremely strong capability of identifying,expressing and disposing such kind of multiple variables and complicated non-linear relations. In this paper,a comprehensive consideration of the strategy of the selection and updating of the concentration and adaptability of the immune algorithm is made to replace the selection mode in the original genetic algorithm which depends simply on the adaptability value. Such an algorithm has the advantages of both the immune algorithm and the genetic algorithm,thus serving the purpose of not only enhancing the individual adaptability but maintaining the individual diversity as well. By use of the identifying function of the antigen memory,the global search capability of the immune genetic algorithm is raised,thereby avoiding the occurrence of the premature phenomenon. By optimizing the structure of the section of the Huayuan tunnel,the current excavation area and support design are adjusted. A conclusion with applicable value is arrived at. At a higher computational speed and a higher efficiency,the current method is verified to have advantages in the optimization computation of the tunnel project. This also suggests that the application of the immune genetic algorithm has a practical significance to the stability assessment and informationization design of the wall rock of the tunnel.

Experimental and Numerical Research on Deformation Behavior of Thin-Walled and Large Expansion Ratio Guide Vane Liner in Hydroforming Process

Some tube hydroforming process tests and further research work were conducted to manufacture hollow guide vane liners( made of super alloy GH3030).The relative thickness( t0/ OD) of the tubular blank is approximately 0. 01,and the maximum expansion ratio( Dmax/ OD) of the needed part is more than 40%,and the length to diameter ratio of the expansion regionis more than 3. 0. It is very hard to manufacture this kind of ultra-thin-wall,curved axis and large expansion ratio tubular part without fracture and wrinkles. The success of the process is highly dependent on useful wrinkles with appropriate internal pressure and axial feeding. A simplified finite element model and a theoretical model are used for detecting the deformation behavior and forming laws. Further study results demonstrate that the useful wrinkles do not appear at the same time and middle-wrinkles need bigger axial force than tube-end-wrinkles and feeding-wrinkles. The wrinkles can transfer bigger axial force after its wave peak has come into contact with the die inner surface. The thickness thinning rate of the element at the peak is bigger than that at the trough. With the increase of the axial and hoop stress ratio,the critical buckling stress also increases. Microstructure examination results show that the grain size in the maximum thinning zone has been stretched and refined after the large deformation and annealing treatment.The process is feasible and the finished part is qualified.

微量元素对超大线能量EH36船板热影响区粗晶区组织和性能的影响

通过焊接热模拟研究了在超大线能量下焊接时Al元素、Mg元素和Ti元素含量对EH36高强船板钢热影响区粗晶区组织、性能的影响规律,采用Thermo-Calc热力学计算与SEM,EDS测试相结合的方法揭示了Al元素、Mg元素和Ti元素含量与母材中氧化物类型、尺寸、数量及粗晶区相变的关系.结果表明,Al_(2)O_(3)无法诱导针状铁素体相变,当Al元素质量分数低于0.005%时,钢中可形成Mg元素、Ti元素或其复合氧化物,可促进粗晶区针状铁素体相变.Mg元素和Ti元素联合添加时,当Mg元素质量分数由0.0042%降低为0.0013%,氧化物类型由MgO转变为Mg_(2)TiO_(4),经统计20个视场内的氧化物数量由408个提高到503个,平均直径由1.37μm减小到1.10μm,显著提高了非均匀形核的比表面积,抑制了晶界铁素体的形成,使t8/5=300 s时粗晶区热模拟试样-20℃冲击吸收能量由43 J提升到127 J.

超大粒径沥青混合料的黏弹特性及温度影响

为精准表征超大粒径沥青混合料(LSAM-50)柔性基层路面的动态黏弹力学响应,对LSAM-50进行动态模量试验,分析了温度对LSAM-50黏弹参数的影响,构建了基于广义对数Sigmoidal模型的黏弹参数主曲线以及基于广义Maxwell模型的黏弹性本构关系.结果表明:温度对LSAM-50黏弹参数的影响显著,温度升高后LSAM-50模量的变化由集料嵌挤力主导,动态模量与存储模量随着温度的升高逐渐降低后趋于稳定;由于LSAM-50具有更大的粒径和集料嵌挤力,其高温抗变形能力比AC-20和AC-13更强;可用广义Maxwell模型构建LSAM-50的黏弹本构关系,其相关性不低于0.99.

四川超级含气盆地古生界大中型气田分布规律及其主控因素

四川盆地是中国天然气资源最为富集的超级含气盆地,但天然气探明程度目前仍然偏低。为了给下一步天然气勘探提供理论支撑,基于该盆地典型气田勘探历程,结合多期构造演化与含油气系统分析,探讨了四川盆地古生界大中型气田富集分布规律及其主控因素,揭示了该盆地巨大的天然气勘探潜力。研究结果表明:①四川盆地古生界蕴含3个超级含油气系统,即下寒武统筇竹寺组(探明储量占该盆地天然气总探明储量的17.55%)、上奥陶统五峰组—下志留统龙马溪组(探明储量占该盆地天然气总探明储量的41.30%)、上二叠统龙潭组/吴家坪组(探明储量占该盆地天然气总探明储量的12.53%);②该盆地古生界已发现20个超大型气田(天然气探明储量超过1000×10^(8)m^(3)),14个大型气田(天然气探明储量介于300×10^(8)~1000×10^(8)m^(3))以及20个中型气田(天然气探明储量介于100×10^(8)~300×10^(8)m^(3)),超大型气田探明储量占该盆地天然气总探明储量的85.5%;③古生界大型隆—坳格局构造沉积分异作用控制影响着该盆地内筇竹寺组、五峰组—龙马溪组和龙潭组/吴家坪组3套优质烃源岩层系的形成与分布。结论认为,晚三叠世以来的陆相盆地演化过程使得中晚三叠世—早中侏罗世成为上述3个超级含油气系统的关键成藏期,形成了3个气田群(绵阳—长宁拉张槽周缘带震旦系—下古生界、开江—梁平与蓬溪—武胜拉张槽周缘带二叠系—三叠系、川东南五峰组—龙马溪组页岩气),其合计天然气储量均超过1×10^(12)m^(3),是该盆地天然气勘探的有利区带。

基于超大型三轴仪的堆石料动力特性缩尺效应研究

堆石料的缩尺效应是导致高土石坝变形预测不准的重要因素之一,目前针对堆石料静力缩尺效应的影响已有部分研究,但针对堆石料动力变形特性的缩尺效应研究仍十分鲜见。本文对两河口板岩及古水玄武岩开展了超大型(试样直径800 mm,最大粒径为160 mm)和常规大型三轴(试样直径300 mm,最大粒径为60 mm)动剪切模量和阻尼比试验,研究了平行相似级配条件下最大粒径对最大动剪切模量、动剪切模量比、阻尼比以及沈珠江等效线性模型参数的影响。试验结果表明:①超大型三轴试验的最大动剪切模量大于常规大型三轴试验,随着动剪应变的增大,超大型和常规大型三轴试验的最大动剪切模量差别逐渐减小;②超大型三轴试验的动剪切模量比G_(d)/G_(dmax)小于常规大型三轴试验,即超大型三轴试验的动剪模量比衰减得更快;③超大型三轴试验的阻尼比大于常规大型三轴试验,随着动剪应变的增加,二者的差距逐渐增大;④超大型三轴试验得到的沈珠江等效线性模型参数k_(2)、k_(1)以及λ_(max)分别是常规大型三轴试验的1.14~1.32倍、1.26~1.31倍以及1.31~1.44倍,超大型和常规大型三轴试验得到的模量指数n差别不大。本文研究成果可为同类工程动力响应分析提供更加合理的试验与数值计算依据。

超大颗粒肥水田气力深施加速器设计及参数优化

为解决水稻撒施追肥存在的肥料流失、利用率低及机械深施肥工作部件易堵塞、伤根等问题,该研究设计了一种用于水田深施追肥机的超大颗粒肥气力式加速器。该加速器利用双螺旋高压气流,在其与肥料上端构成的近封闭空间内加速超大颗粒肥,实现其高速射入泥壤,并可避免肥料颗粒与管壁碰撞;出口设置渐扩管扩散气流,可减轻对泥壤的冲击,提高施肥位置的稳定性。根据超大颗粒肥参数与加速器功能要求,确定了加速器的结构参数,并根据肥料入泥深度所需的射出速度,分析确定了加速器的工作参数。在此基础上,基于Fluent软件的六自由度重叠动网格建立了加速器仿真模型,以进口气流速度、螺旋角和加速管直径为试验因素,进行单因素仿真试验与三因素三水平Box Behnken组合仿真试验,研究各因素对肥料射出速度与气流扩散率的影响。多因素试验分析及响应面分析结果表明,加速器的最佳工作参数为进口气流速度47 m/s、加速管直径21 mm、螺旋进气口螺旋角43°。在此条件下进行台架验证试验,得到肥料射出速度均值为12.61 m/s,出口气流扩散率均值为85.5%,肥料入泥平均深度为4.7 cm,达到了水稻追肥要求。该研究可为超大颗粒肥水田气力深施追肥机设计提供参考。

船舶超大空间火灾环境下人员疏散模型

针对船舶超大空间火灾对人员疏散能力的影响难以量化问题,本文基于元胞自动机理论,构建了一种行人个体自主分析火灾环境下温度和能见度影响的疏散模型(cellular automata model considering visibility and temperature, CAVT)。CAVT模型采用Sigmoid函数和历史实验数据建立温度、能见度与人员运动能力的映射关系,基于FDS数值模拟结果建立火灾环境场对人员个体运动能力影响的时空耦合关系,使用熵值法计算温度场和能见度场在火灾环境场中的权重。以某客船超大空间为例开展研究分析,结果表明:火灾环境下人员疏散时间受火源功率影响较大,火源位置影响较小,出口宽度大于3 m,不影响疏散效率。与Pathfinder软件相比,CAVT模型可更准确模拟人员因高温和低能见度导致的运动能力的动态下降反馈。

浅谈中国未来大型水电装备技术挑战与创新

我国水电资源丰富、开发程度处于中等水平,远不及欧洲发达国家。“双碳”战略下,水电作为清洁能源,以其高调节性、高稳定性将在以新能源为主的新型电力系统中发挥“压舱石”作用。资源特点和经济性决定未来水电开发将朝向更高水头(高转速)、更大容量趋势发展,机组将具备高海拔环境运行、超高水头、超大容量的特点。开发难度极高,技术挑战前所未有,亟待攻克。该文从多个角度分析阐述特殊工况下我国水电装备开发面临的问题和技术挑战,探讨关键技术发展趋势以及创新技术应用潜力,为未来水电装备的技术创新和突破提供参考方向。

基于深度学习的超大直径盾构姿态预测研究

传统的盾构姿态纠偏措施多是在盾构机实际轴线已经偏离设计轴线之后采取的被动控制措施,具有一定的滞后性,而盾构姿态纠偏不及时会给施工过程和完成后的隧道本身带来严重的危害。为了准确预测盾构姿态偏差,为提前纠偏提供决策支持,本文依托江阴—靖江长江隧道超大直径盾构施工项目,提出一种基于CNN-EMD-LSTM的深度学习模型,该模型既能捕捉时间序列的维度特征和时变特征,又能提高盾构姿态数据分解重构方法的预测精度;通过消融实验对CNN-EMD-LSTM模型中每个部分的重要性进行探讨,并对CNN-EMD-LSTM模型在不同窗口长度、不同滑动步长下的预测效果进行对比。研究结果表明:CNN-EMD-LSTM模型对超大直径盾构姿态的预测效果较好;可以通过调节不同推进区间的压力进行盾构姿态纠偏;CNN-EMD-LSTM模型中各个部分按重要性从大到小排序依次为EMD、CNN、LSTM;窗口长度过大或过小都会增大模型预测误差,而滑动步长越小模型的预测效果越好。