Pneumatic down-the-hole (DTH) hammer has been extensively used in air drillings through hard and ultra-hard geological formations. Numerical modeling can offer close observation on the working behaviors by visualizing...Pneumatic down-the-hole (DTH) hammer has been extensively used in air drillings through hard and ultra-hard geological formations. Numerical modeling can offer close observation on the working behaviors by visualizing internal pressure status as well as provide reliable performance predictions for large-diameter DTH hammers to which conventional empirical and experimental approaches cannot be applied. In this study, CFD simulations coupled with dynamic meshing are utilized to simulate the air flow and piston movement inside the large-diameter DTH hammers. The numerical modeling scheme is verified against a theoretical model published in literature. Effects of structural parameters on hammer performance, including piston mass, piston upper-end diameter, piston groove diameter, and lengths of intake and exhaust stroke in both front and rear chambers, are analyzed in detail by virtue of sets of numerical simulations. The simulations suggest that changing the intake stroke of front chamber has a negligible influence on hammer performance while increasing the piston groove would lower all the four indicators of hammer performance, including impact energy, impact frequency, maximum stroke, and air consumption rate. Changing the other structural parameters demonstrates mixed effects on the performance indicators. Based on the numerical simulations, a large GQ-400 DTH hammer has been designed for reduced air consumption rate and tested in a field drilling practice. The air drilling test with the designed hammer provided a penetration rate 1.7 times faster than that of conventional mud drilling.展开更多
In the past two decades,numerous large-diameter rock-socketed piles were constructed in China to support foundations of skyscrapers,great bridges or to retain soil in potential geological hazard areas.However,drilling...In the past two decades,numerous large-diameter rock-socketed piles were constructed in China to support foundations of skyscrapers,great bridges or to retain soil in potential geological hazard areas.However,drilling large-diameter rock-socketed pile holes with conventional drilling method such as rotary drilling or cable tool drilling is time-consuming and the cost is usually very high.In order to drill large-diameter rock-socketed pile holes faster at relatively low cost,the FGC15A large-diameter DTH air hammer drilling system was developed in 1987 and was given the second-class award by Ministry of Geology and Mineral Resources in 1991.Since it was innovated the drilling system has been used in more than twenty important and tough projects on land,and wonderful results were acquired.At the same time the large-diameter DTH air hammer drilling system was improved continuously.The FGC15D is the latest version of the technique.展开更多
Rock and geotechnical engineering investigations involve drilling holes in ground with or without retrieving soil and rock samples to construct the subsurface ground profile.On the basis of an actual soil nailing dril...Rock and geotechnical engineering investigations involve drilling holes in ground with or without retrieving soil and rock samples to construct the subsurface ground profile.On the basis of an actual soil nailing drilling for a slope stability project in Hong Kong,this paper further develops the drilling process monitoring(DPM)method for digitally profiling the subsurface geomaterials of weathered granitic rocks using a compressed airflow driven percussive-rotary drilling machine with down-the-hole(DTH)hammer.Seven transducers are installed on the drilling machine and record the chuck displacement,DTH rotational speed,and five pressures from five compressed airflows in real-time series.The mechanism and operations of the drilling machine are elaborated in detail,which is essential for understanding and evaluating the drilling data.A MATLAB program is developed to automatically filter the recorded drilling data in time series and classify them into different drilling processes in sub-time series.These processes include penetration,push-in with or without rod,pull-back with or without rod,rod-tightening and rod-untightening.The drilling data are further reconstructed to plot the curve of drill-bit depth versus the net drilling time along each of the six drillholes.Each curve is found to contain multiple linear segments with a constant penetration rate,which implies a zone of homogenous geomaterial with different weathering grades.The effect from fluctuation of the applied pressures is evaluated quantitatively.Detailed analyses are presented for accurately assess and verify the underground profiling and strength in weathered granitic rock,which provided the basis of using DPM method to confidently assess drilling measurements to interpret the subsurface profile in real time.展开更多
The pneumatic down-the-hole(DTH) hammer is one of the efficient equipments used in medium hard to very hard rock drilling frield,and any change in its structure design affects all performance parameters of a pneuamtic...The pneumatic down-the-hole(DTH) hammer is one of the efficient equipments used in medium hard to very hard rock drilling frield,and any change in its structure design affects all performance parameters of a pneuamtic DTH hammer directly.Yet,owing to the complexity of the dynamic interaction among the components in DTH hammer systems,until now it has been difficult to obtain reliable estimates of the design parameter affects.Thus providing an design parameter optimization and the layout of dynamics behavior of DTH hammer is of great importance.This paper documents the development and solution of a computational model for the dynamic response of a pneumatic DTH hammer.The model consists of rigid piston dynamics equation and chamber thermodynamics equations.The resulting model represented by a set of coupled nonlinear differential equations were computed in Visual C++ program.The developed solutions are used to perform a parametric study to illustrate the inffluence of the piston mass and supply pressure on the impact performance of DTH hammer system.展开更多
The technical characteristics and operational principal of the reverse circulation DTH hammer drilling technology is integrated introduced in this paper. Using simulation technology to assist the drilling tool design,...The technical characteristics and operational principal of the reverse circulation DTH hammer drilling technology is integrated introduced in this paper. Using simulation technology to assist the drilling tool design, the optimum designed DTH hammer gets stable performance, and the bit has reverse circulation ability, and further more, it has already developed serial products. The reverse circulation DTH hammer drilling technique has been fully applied in field such as the geological core exploration in complex strata, water well drilling, and large diameter rock embedding piles drilling in hard rock, and obviously, it is achieved favorable economic and social benefits.展开更多
Air DTH hammer has been successfully applied in minor-caliber solid mineral exploration,water-well drilling and other drilling areas. In order to expand the applications of the technology,the authors further studied t...Air DTH hammer has been successfully applied in minor-caliber solid mineral exploration,water-well drilling and other drilling areas. In order to expand the applications of the technology,the authors further studied the principle and analyzed the mechanism of reverse circulation drilling technique with air DTH hammer to get the perfect assembles of equipments by optimizing working parameters. No parameter seemed more important than the air volume because it could maintain the working performance stability. The minimum air volume is related to the parameters such as depth and pressure,which was calculated under the actual conditions. It was solved for the air injection flow tables of the air DTH Hammer working at the different pressures. According to the data tables,operators could adjust the air volume to meet the demand on this technique,which had a realistic guiding significance. So it could build up a set of systematic and complete hi-technique.展开更多
The authors tested the percussion-extruding Down-the-hole(DTH)hammer bit with five different structures and mainly analyzed the drilling mechanism between conical bit and stepped bit.In addition,aiming at "the pi...The authors tested the percussion-extruding Down-the-hole(DTH)hammer bit with five different structures and mainly analyzed the drilling mechanism between conical bit and stepped bit.In addition,aiming at "the pile effect" in combination with the advantage of stepped bit,we design a new cam spinning bit and test it outdoors.The result shows that using cam spinning bit can solve the problem of "the pile effect",which can also obtain higher drilling efficiency than using conical bit in high confining pressure strata.It is characterized by novel structure and high drilling speed as well as good guiding,and it is significant for improving efficiency in percussion-extruding drilling technique.展开更多
Air down-the-hole(DTH)hammer drilling has long been recognized to have the potential of drilling faster than conventional rotary drill,especially in some hard rocks such as granite,sandstone,limestone,dolomite,etc.wit...Air down-the-hole(DTH)hammer drilling has long been recognized to have the potential of drilling faster than conventional rotary drill,especially in some hard rocks such as granite,sandstone,limestone,dolomite,etc.with the same weight on bit(WOB)and rotations per minute(RPM).So,it has been widely used in many drilling fields including mineral resource exploration drilling,oil and gas drilling and geothermal drilling.In order to reduce drilling cost by selecting optimal drilling parameters,rate of penetration(ROP)should be estimated accurately and the effects of different factors on ROP should be analyzed.In this research,ANN model with several multi-layer perception back propagation(BP)networks for predicting ROP of air DTH hammer drilling was developed using controllable parameters such as impact energy,impact frequency,WOB,RPM and bit operating time for the formations with a certain drillability index of rock.Several BP neural networks with the different neurons in hidden layers were developed and compared for selecting optimal architecture of ANN.The effects of the drilling parameters such as impact energy,impacting frequency,WOB,RPM and bit operating time on the ROP of air DTH hammer drilling were investigated by trained ANN.From the analyses,the optimum range of drilling parameters for providing high ROP were determined and analyzed for a formation with a certain drillability index of rock.The methodology proposed in this study can be used in many mathematical problems for optimization of drilling process with air DTH hammer.展开更多
Casing-while-drilling(CWD)with down the hole(DTH)hammer drilling technology has been widely used in unconsolidated formations,due to its advantages in protecting the borehole wall,excellent rock cuttings capacity,and ...Casing-while-drilling(CWD)with down the hole(DTH)hammer drilling technology has been widely used in unconsolidated formations,due to its advantages in protecting the borehole wall,excellent rock cuttings capacity,and fast penetration rate in hard rock.As an important component of the CWD system,the structure of the retractable drill bit needs not only to ensure to form stronger reverse circulation,but also to be expandable or retractable as needed,otherwise the drill bit cannot be lift and put down smoothly in the casing,and may lead to drilling accidents.This paper developed a new type of reverse circulation DTH hammer drill bit used for CWD drilling technology.The retractable performance of this type of drill bit is studied using ADAMS software.The results show that it is smoothly expandable and retractable as designed under the conditions of the weight of the bit(WOB)of 0.5–2.0 t and the rotation speed of 30–60 r/min.To investigate the reverse circulation effect of the drill bit,Fluent software was used to simulate the flow characteristic inside it.The simulation results indicated that it can form strong reverse circulation,and the entrainment ratio h can reach 9.5%.展开更多
基金This work was supported by the Natural Science Foundation of Jilin Province(YDZj202101ZYTS143)National Key Research and Development Project of China(project No.2018YFC1505303).
文摘Pneumatic down-the-hole (DTH) hammer has been extensively used in air drillings through hard and ultra-hard geological formations. Numerical modeling can offer close observation on the working behaviors by visualizing internal pressure status as well as provide reliable performance predictions for large-diameter DTH hammers to which conventional empirical and experimental approaches cannot be applied. In this study, CFD simulations coupled with dynamic meshing are utilized to simulate the air flow and piston movement inside the large-diameter DTH hammers. The numerical modeling scheme is verified against a theoretical model published in literature. Effects of structural parameters on hammer performance, including piston mass, piston upper-end diameter, piston groove diameter, and lengths of intake and exhaust stroke in both front and rear chambers, are analyzed in detail by virtue of sets of numerical simulations. The simulations suggest that changing the intake stroke of front chamber has a negligible influence on hammer performance while increasing the piston groove would lower all the four indicators of hammer performance, including impact energy, impact frequency, maximum stroke, and air consumption rate. Changing the other structural parameters demonstrates mixed effects on the performance indicators. Based on the numerical simulations, a large GQ-400 DTH hammer has been designed for reduced air consumption rate and tested in a field drilling practice. The air drilling test with the designed hammer provided a penetration rate 1.7 times faster than that of conventional mud drilling.
文摘In the past two decades,numerous large-diameter rock-socketed piles were constructed in China to support foundations of skyscrapers,great bridges or to retain soil in potential geological hazard areas.However,drilling large-diameter rock-socketed pile holes with conventional drilling method such as rotary drilling or cable tool drilling is time-consuming and the cost is usually very high.In order to drill large-diameter rock-socketed pile holes faster at relatively low cost,the FGC15A large-diameter DTH air hammer drilling system was developed in 1987 and was given the second-class award by Ministry of Geology and Mineral Resources in 1991.Since it was innovated the drilling system has been used in more than twenty important and tough projects on land,and wonderful results were acquired.At the same time the large-diameter DTH air hammer drilling system was improved continuously.The FGC15D is the latest version of the technique.
基金supported by grants from the Research Grant Council of the Hong Kong Special Administrative Region,China(Project Nos.HKU 7137/03E and R7005/01E)。
文摘Rock and geotechnical engineering investigations involve drilling holes in ground with or without retrieving soil and rock samples to construct the subsurface ground profile.On the basis of an actual soil nailing drilling for a slope stability project in Hong Kong,this paper further develops the drilling process monitoring(DPM)method for digitally profiling the subsurface geomaterials of weathered granitic rocks using a compressed airflow driven percussive-rotary drilling machine with down-the-hole(DTH)hammer.Seven transducers are installed on the drilling machine and record the chuck displacement,DTH rotational speed,and five pressures from five compressed airflows in real-time series.The mechanism and operations of the drilling machine are elaborated in detail,which is essential for understanding and evaluating the drilling data.A MATLAB program is developed to automatically filter the recorded drilling data in time series and classify them into different drilling processes in sub-time series.These processes include penetration,push-in with or without rod,pull-back with or without rod,rod-tightening and rod-untightening.The drilling data are further reconstructed to plot the curve of drill-bit depth versus the net drilling time along each of the six drillholes.Each curve is found to contain multiple linear segments with a constant penetration rate,which implies a zone of homogenous geomaterial with different weathering grades.The effect from fluctuation of the applied pressures is evaluated quantitatively.Detailed analyses are presented for accurately assess and verify the underground profiling and strength in weathered granitic rock,which provided the basis of using DPM method to confidently assess drilling measurements to interpret the subsurface profile in real time.
基金This study was supported by the NSFC No.50475056
文摘The pneumatic down-the-hole(DTH) hammer is one of the efficient equipments used in medium hard to very hard rock drilling frield,and any change in its structure design affects all performance parameters of a pneuamtic DTH hammer directly.Yet,owing to the complexity of the dynamic interaction among the components in DTH hammer systems,until now it has been difficult to obtain reliable estimates of the design parameter affects.Thus providing an design parameter optimization and the layout of dynamics behavior of DTH hammer is of great importance.This paper documents the development and solution of a computational model for the dynamic response of a pneumatic DTH hammer.The model consists of rigid piston dynamics equation and chamber thermodynamics equations.The resulting model represented by a set of coupled nonlinear differential equations were computed in Visual C++ program.The developed solutions are used to perform a parametric study to illustrate the inffluence of the piston mass and supply pressure on the impact performance of DTH hammer system.
基金Supported by the Fundamental Research Funds for Jilin University (No. 200903203)
文摘The technical characteristics and operational principal of the reverse circulation DTH hammer drilling technology is integrated introduced in this paper. Using simulation technology to assist the drilling tool design, the optimum designed DTH hammer gets stable performance, and the bit has reverse circulation ability, and further more, it has already developed serial products. The reverse circulation DTH hammer drilling technique has been fully applied in field such as the geological core exploration in complex strata, water well drilling, and large diameter rock embedding piles drilling in hard rock, and obviously, it is achieved favorable economic and social benefits.
基金supported by the project of the feasibility study on air reverse circulation drilling system,research foundation for out standingteachers,Jilin University(No.2006220100003435)
文摘Air DTH hammer has been successfully applied in minor-caliber solid mineral exploration,water-well drilling and other drilling areas. In order to expand the applications of the technology,the authors further studied the principle and analyzed the mechanism of reverse circulation drilling technique with air DTH hammer to get the perfect assembles of equipments by optimizing working parameters. No parameter seemed more important than the air volume because it could maintain the working performance stability. The minimum air volume is related to the parameters such as depth and pressure,which was calculated under the actual conditions. It was solved for the air injection flow tables of the air DTH Hammer working at the different pressures. According to the data tables,operators could adjust the air volume to meet the demand on this technique,which had a realistic guiding significance. So it could build up a set of systematic and complete hi-technique.
文摘The authors tested the percussion-extruding Down-the-hole(DTH)hammer bit with five different structures and mainly analyzed the drilling mechanism between conical bit and stepped bit.In addition,aiming at "the pile effect" in combination with the advantage of stepped bit,we design a new cam spinning bit and test it outdoors.The result shows that using cam spinning bit can solve the problem of "the pile effect",which can also obtain higher drilling efficiency than using conical bit in high confining pressure strata.It is characterized by novel structure and high drilling speed as well as good guiding,and it is significant for improving efficiency in percussion-extruding drilling technique.
文摘Air down-the-hole(DTH)hammer drilling has long been recognized to have the potential of drilling faster than conventional rotary drill,especially in some hard rocks such as granite,sandstone,limestone,dolomite,etc.with the same weight on bit(WOB)and rotations per minute(RPM).So,it has been widely used in many drilling fields including mineral resource exploration drilling,oil and gas drilling and geothermal drilling.In order to reduce drilling cost by selecting optimal drilling parameters,rate of penetration(ROP)should be estimated accurately and the effects of different factors on ROP should be analyzed.In this research,ANN model with several multi-layer perception back propagation(BP)networks for predicting ROP of air DTH hammer drilling was developed using controllable parameters such as impact energy,impact frequency,WOB,RPM and bit operating time for the formations with a certain drillability index of rock.Several BP neural networks with the different neurons in hidden layers were developed and compared for selecting optimal architecture of ANN.The effects of the drilling parameters such as impact energy,impacting frequency,WOB,RPM and bit operating time on the ROP of air DTH hammer drilling were investigated by trained ANN.From the analyses,the optimum range of drilling parameters for providing high ROP were determined and analyzed for a formation with a certain drillability index of rock.The methodology proposed in this study can be used in many mathematical problems for optimization of drilling process with air DTH hammer.
基金the National Key Research and Development Program of China(No.2018YFC1505303).
文摘Casing-while-drilling(CWD)with down the hole(DTH)hammer drilling technology has been widely used in unconsolidated formations,due to its advantages in protecting the borehole wall,excellent rock cuttings capacity,and fast penetration rate in hard rock.As an important component of the CWD system,the structure of the retractable drill bit needs not only to ensure to form stronger reverse circulation,but also to be expandable or retractable as needed,otherwise the drill bit cannot be lift and put down smoothly in the casing,and may lead to drilling accidents.This paper developed a new type of reverse circulation DTH hammer drill bit used for CWD drilling technology.The retractable performance of this type of drill bit is studied using ADAMS software.The results show that it is smoothly expandable and retractable as designed under the conditions of the weight of the bit(WOB)of 0.5–2.0 t and the rotation speed of 30–60 r/min.To investigate the reverse circulation effect of the drill bit,Fluent software was used to simulate the flow characteristic inside it.The simulation results indicated that it can form strong reverse circulation,and the entrainment ratio h can reach 9.5%.