This paper presents an analytical investigation of water hammer in a hydraulic pressurized pipe system with a throttled surge chamber located at the junction between a tunnel and a penstock, and a valve positioned at ...This paper presents an analytical investigation of water hammer in a hydraulic pressurized pipe system with a throttled surge chamber located at the junction between a tunnel and a penstock, and a valve positioned at the downstream end of the penstock. Analytical formulas of maximum water hammer pressures at the downstream end of the tunnel and the valve were derived for a system subjected to linear and slow valve closure. The analytical results were then compared with numerical ones obtained using the method of characteristics. There is agreement between them. The formulas can be applied to estimating water hammer pressure at the valve and transmission of water hammer pressure through the surge chamber at the junction for a hydraulic pipe system with a surge chamber.展开更多
Experimental investigations are made on the effects of operating conditionson the flow characteristics of throttle when tap water is used as the working media. The researchedthrottles include cone poppet valve, ball v...Experimental investigations are made on the effects of operating conditionson the flow characteristics of throttle when tap water is used as the working media. The researchedthrottles include cone poppet valve, ball valve, disc valve and dumping orifice. Operating conditionincludes poppet lift, working media, back pressure, medium temperature, etc. Because the vapourouspressure of water is much higher than that of oil, cavitation is easier to occur in water hydraulicelements and systems, so the effects of operating conditions on the cavitation characteristics ofthrottle are also researched.展开更多
Cooling strength is one of the important factors affecting microstructure and properties of gas cylinders during quenching process,and reasonable water spray volume can effectively improve the quality of gas cylinders...Cooling strength is one of the important factors affecting microstructure and properties of gas cylinders during quenching process,and reasonable water spray volume can effectively improve the quality of gas cylinders and reduce production costs.To find the optimal water spray parameters,a fluid-solid coupling model with three-phase flow was established in consideration of water-vapor conversion.The inner and outer walls of gas cylinder with the dimensions of d914 mm×38 mm×12000 mm were quenched using multi-nozzle water spray system.The internal pressure,average heat transfer coefficient(have)and stress of the gas cylinder under different water spray volumes during quenching process were studied.Finally,the mathematical model was experimentally verified.The results show that both the internal pressure and have increase along with the increase of spray volume.The internal pressure increases slowly first and then rapidly,but have increases rapidly first and then slowly.To satisfy hardenability of gas cylinders,the minimum spray volume should not be less than 40 m^3/(h·m).The results of stress indicate that water spray quenching will not cause deformation of bottle body in the range of water volume from 40 to 290 m^3/(h·m).展开更多
In allusion to easy invalidation of damping valve in vehicle shock absorber caused by the impact from the road surface, the importance of the study of damping valve water hammer pressure is presented. The physical mod...In allusion to easy invalidation of damping valve in vehicle shock absorber caused by the impact from the road surface, the importance of the study of damping valve water hammer pressure is presented. The physical model of damping valve with the circle throttle slice is established. The time for the throttle slice deformation is studied by using the finite software, and the laws that how the structure parameters affect the deformation time are obtained. Combining the theory of water hammer, the water hammer initial and boundary condition of the damping valve is deduced, and the water hammer model of throttle slice is established. The analysis of simulation results indicates that the water hammer pressure amplitude and the amount of water hammer oscillation period can be reduced and the dependability of the valve can be enhanced by modifying the structure parameters and aperture width between slice and valve body.展开更多
基金supported by the National Natural Science Foundation of China (Grant No.50539070)the Major State Basic Research Development Program of China (Grant No.2006CB403304)
文摘This paper presents an analytical investigation of water hammer in a hydraulic pressurized pipe system with a throttled surge chamber located at the junction between a tunnel and a penstock, and a valve positioned at the downstream end of the penstock. Analytical formulas of maximum water hammer pressures at the downstream end of the tunnel and the valve were derived for a system subjected to linear and slow valve closure. The analytical results were then compared with numerical ones obtained using the method of characteristics. There is agreement between them. The formulas can be applied to estimating water hammer pressure at the valve and transmission of water hammer pressure through the surge chamber at the junction for a hydraulic pipe system with a surge chamber.
基金This project is supported by National Natural Science Foundation of China (No.50375056, 59975031).
文摘Experimental investigations are made on the effects of operating conditionson the flow characteristics of throttle when tap water is used as the working media. The researchedthrottles include cone poppet valve, ball valve, disc valve and dumping orifice. Operating conditionincludes poppet lift, working media, back pressure, medium temperature, etc. Because the vapourouspressure of water is much higher than that of oil, cavitation is easier to occur in water hydraulicelements and systems, so the effects of operating conditions on the cavitation characteristics ofthrottle are also researched.
基金Project(51674096)supported by the National Natural Science Foundation of ChinaProject(E2016203119)supported by Hebei Natural Science Foundation of ChinaProject(18211045)supported by the Key Research and Development Foundation in Hebei Province of China
文摘Cooling strength is one of the important factors affecting microstructure and properties of gas cylinders during quenching process,and reasonable water spray volume can effectively improve the quality of gas cylinders and reduce production costs.To find the optimal water spray parameters,a fluid-solid coupling model with three-phase flow was established in consideration of water-vapor conversion.The inner and outer walls of gas cylinder with the dimensions of d914 mm×38 mm×12000 mm were quenched using multi-nozzle water spray system.The internal pressure,average heat transfer coefficient(have)and stress of the gas cylinder under different water spray volumes during quenching process were studied.Finally,the mathematical model was experimentally verified.The results show that both the internal pressure and have increase along with the increase of spray volume.The internal pressure increases slowly first and then rapidly,but have increases rapidly first and then slowly.To satisfy hardenability of gas cylinders,the minimum spray volume should not be less than 40 m^3/(h·m).The results of stress indicate that water spray quenching will not cause deformation of bottle body in the range of water volume from 40 to 290 m^3/(h·m).
基金Sponsored by the Ministerial Level Advanced Research Foundation (623010202 4)
文摘In allusion to easy invalidation of damping valve in vehicle shock absorber caused by the impact from the road surface, the importance of the study of damping valve water hammer pressure is presented. The physical model of damping valve with the circle throttle slice is established. The time for the throttle slice deformation is studied by using the finite software, and the laws that how the structure parameters affect the deformation time are obtained. Combining the theory of water hammer, the water hammer initial and boundary condition of the damping valve is deduced, and the water hammer model of throttle slice is established. The analysis of simulation results indicates that the water hammer pressure amplitude and the amount of water hammer oscillation period can be reduced and the dependability of the valve can be enhanced by modifying the structure parameters and aperture width between slice and valve body.
