Distribution, health and ecological risk assessments of trace elements in Nigerian oil sands

The Nigerian oil sands represent the largest oil sand deposit in Africa, yet there is little published information on the distribution and potential health and ecological risks of trace elements in the oil resource. In the present study, we investigated the distribution pattern of 18trace elements(including biophile and chalcophile elements) as well as the estimated risks associated with exposure to these elements. The results of the study indicated that Fe was the most abundant element, with a mean concentration of 22,131 mg/kg while Br had the lowest mean concentration of 48 mg/kg. The high occurrence of Fe and Ti suggested a possible occurrence of ilmenite(Fe TiO_(3)) in the oil sands. Source apportionment using positive matrix factorization showed that the possible sources of detected elements in the oil sands were geogenic, metal production, and crustal. The contamination factor, geo-accumulation index, modified degree of contamination, pollution load index, and Nemerow pollution index indicated that the oil sands are heavily polluted by the elements. Health risk assessment showed that children were relatively more susceptible to the potentially toxic elements in the oil sands principally via ingestion exposure route(HQ > 1E-04). Cancer risks from inhalation are unlikely due to CR < 1E-06 but ingestion and dermal contact pose severe risks(CR > 1E-04). The high concentrations of the elements pose serious threats due to the potential for atmospheric transport, bioaccessibility, and bioavailability.

Liquefaction and post-liquefaction behaviors of sands affected by immersion-induced degradation of crushed mudstone

A series of undrained triaxial tests was conducted to investigate the effect of crushed mudstone with the immersion-induced degradation on the liquefaction and post-liquefaction properties,and the undrained shearing behavior without precedent cyclic-loading histories of sands containing crushed mudstone.The tested materials with a main particle diameter of 2-0.85 mm were prepared by mixing sands and crushed mudstone to reach the prescribed mudstone content defined by dry mass ranging from 0% to 50%.The mixtures were subjected to immersion under a certain stress level and were subsequently tested.In addition,one-dimensional compression tests were also supplementally performed to visually observe the immersion-induced degradation of crushed mudstone.The test results mainly showed that: (1) the liquefaction resistance,the post-liquefaction undrained strength,and the undrained strength without a precedent cyclic-loading history decreased significantly with increasing mudstone content,M c ,up to 20%;(2) even a small amount of crushed mudstone affected these strengths;(3) the above-mentioned large reductions in the strengths were attributed to the immersion-induced degradation of crushed mudstone;(4) at M_(c) >20%,the liquefaction resistance increased while the significant increase in the undrained static strengths with and without precedent cyclic-loading histories was not observed;and (5) the increase in the liquefaction resistance at M_(c) >20% may have been attributed to both the gradual increase in the plasticity and the formation of the soil aggregates among deteriorated crushed mudstone,while the increase in the specimen density did not play an important role in such behavior.

Impact of Reservoir Heterogeneity on Bitumen Content in the Mackay River Oil Sands,Athabasca(Canada)

The Lower Cretaceous Manville Group of Upper Mc Murray Formation is one of the main bitumen reservoirs in Athabasca.In this study,the relationship between reservoirs heterogeneity and bitumen geochemical characteristics were analyzed through core and microscopic observation,lab analysis,petrophysics and logging data.Based on the sedimentology framework,the formation environment of high-quality oil sand reservoirs and their significance for development were discussed.The results indicate that four types lithofacies were recognized in the Upper Mc Murray Formation based on their depositional characteristics.Each lithofacies reservoirs has unique physical properties,and is subject to varying degrees of degradation,resulting in diversity of bitumen content and geochemical composition.The tidal bar(TB)or tidal channel(TC)facies reservoir have excellent physical properties,which are evaluated as gas or water intervals due to strong degradation.The reservoir of sand bar(SB)facies was evaluated as oil intervals,due to its poor physical properties and weak degradation.The reservoir of mixed flat(MF)facies is composed of sand intercalated with laminated shale,which is evaluated as poor oil intervals due to its poor connectivity.The shale content in oil sand reservoir is very important for the reservoir physical properties and bitumen degradation degree.In the context of regional biodegradation,oil sand reservoirs with good physical properties will suffer from strong degradation,while oil sand reservoirs with relatively poor physical properties are more conducive to the bitumen preservation.

Study of Sands from Bamendou-West Cameroon: Valorization for Concrete Mix Design

Bamendou (West Cameroon), has a huge potential in natural resources, especially sands. However, the use of these materials in civil engineering works leads to the appearance of numerous pathologies which in some cases lead to the total ruin of the works. In order to overcome these infrastructural problems, the main objective of this study is set at the improvement of the service life of structures built in Cameroon using local materials formed under climatic, geological and geotechnical conditions similar to those of materials in Bamendou. Eight sand samples were taken from the most representative and exploited quarries. The identification and classification of the sand taken from the most representative quarries in the study area show that they are mainly clayey, with an average sand equivalent of 57.54. In terms of granulometry, the curves of several sand samples do not fall within the granular range of sands used in the formulation of concrete. The modulus of fineness obtained by particle size analysis varies from 2.91 to 3.92 with an average of 3.31.

Measurement of the Level of Knowledge of the Sands Used in Constructions in Togo

Faced with the proliferation of quarries extracting silty sand and river sand used in the building and public works sector in Togo, recognition of the granular properties of these materials remains a major challenge for builders. This study aims to take stock of the use of sand in construction in Togo. One hundred and eighteen (118) sand quarries in operation, including thirty-eight (38) silty sand quarries and eighty (80) river sand quarries, were identified following surveys carried out among stakeholders involved in the chain of construction on 40% of the national territory. It appears from these surveys that river sands (59.43% to 84.68%) are prioritized over silty sands (15.32% to 40.57%). Three (3) main reasons are behind the choice of sand type;namely, proximity (28%), cleanliness (25%), good appearance (25%). These three (03) reasons partly explain the strong dependence of users on the sands located in their vicinity as well as the related expenses. Thus, making data available on the characteristics of sand, the materials most used in construction in Togo, would contribute to improving the housing conditions of the Togolese population. .

Granulometric and Mineralogical Characterization of the Sands of the Middle Course of the Kasai River (Territory of Ilebo, Province of Kasai/DR Congo)

The sand bars, in perpetual transformation, observable in the middle course of the Kasai river on the section between the city of Ilebo (pk605) to the confluence of the Loange river (pk525), pose enormous navigability problems. This may be dependent on hydrosedimentological characteristics of the Kasai River. This abundance of sand thus conditions the morphology of the middle course of the Kasai River in the section under our study. It therefore constitutes sedimentary navigation obstacles. The objective of this study is the granulometric and mineralogical characterization of the bar sands of the Kasai River in this study section. Particle size analyzes reveal these are moderately well classified to well classified unimodal sands (Classification coefficient between 1.29 to 1.742) largely presenting grain size symmetry and rarely fine asymmetry (Asymmetry coefficient—Skewness between −0.197 to 0.069) with mesorkurtic and rarely leptokurtic and platykurtic acuity (Angulosity coefficient—Kurtosis between 0.814 to 1.323). All these parameters evolve in sawtooth patterns from upstream to downstream. And then, an automated mineralogical analysis of the sands of the Kasaï River using a Qemscan FEG Quanta 650 made it possible to determine a very varied mineralogical procession with a sawtooth evolution. It is largely dominated by quartz (between 93.73% and 99.07%), followed by calcite (0.01% - 2.66%), iron oxides (0.01% - 1.88%), orthoclase (0.04% - 0.99%), plagioclase (0.01% - 0.75%) and Kaolinite (0.18% - 0.71%). Finally, this mineralogical procession is characterized by a group of minerals which do not reach the threshold of 0.55% such as: illite, apatite, ilmenite, muscovite, chlorite, biotite, montmorillonite, rutile, pyrophyllite, siderite, zircon and dolomite. The evolution of the mineralogical procession of the sands of the bars is not as clear as in the case of particle size parameters.

Shear Resistance of Siltous Sands Improved with Bridelia Tannins

The ruin of several civil engineering works occurs due to shear rupture of the ground. When the stress is greater than the shear resistance, the internal friction angle and the cohesion of the soil loosen and rupture occurs. Cement and lime are often used to stabilize soils and improve soil strength. The costs and environmental problems of these technologies raise concerns and challenge researchers to innovate with clean, inexpensive materials, accessible to the most disadvantaged social classes. The question that this study seeks to answer is whether the binders derived from plant tannins, which also stabilize soils, improve the shear resistance of these soils. To do this, we determined for silty sand the shear parameters, notably the cohesion and the angle of internal friction in the non-stabilized state and when they are stabilized with the powder of the bark of the Bridelia under different water states. The results show that the addition of Bridelia powder to silty sand increases the cohesion of the soil by nearly 70.71% and the friction angle by 4.31%. But in unfavourable water conditions, the cohesion and internal friction angle of the silty sand material improved with Bridelia bark powder drops drastically by nearly 81.56%. but does not dissolve completely as for the same material. When it is not stabilized. This information is an invaluable contribution in the search for solutions to increase the durability of earthen constructions by improving the water-repellent properties of soils.

Sedimentary Dynamics of the Sands of the Cover Formation in the Batéké Plateaus (Republic of Congo): Paleoenvironmental Implications

The depositional environment of the sands of the cover formation is discussed. This study aims to determine the paleoenvironments of deposition of the sands of the cover formation in the Batéké Plateaus by studying sedimentary dynamics based on the description of lithological facies in the field and granulometric analyses in the laboratory. In the field, six (6) lithostratigraphic logs were surveyed and 42 sand samples were taken for laboratory analysis. In the laboratory, the samples underwent granulometric, sieving and sedimentometry analyses, after washing with running water using a 63 µm sieve. These analyses made it possible to determine the granulometric classes of the samples. The sieving results allowed to determine the granulometric parameters (mean, standard deviation, mode, median, skewness, flattening or kurtosis) using the method of moments with the software “Gradistat V.8”, granulometric parameters with which the granulometric facies, the mode of transport and the deposition environment were determined using the diagrams. Morphoscopy made it possible to determine the form and aspect of the surface of the quartz grains constituting these sands. Granulometric analyses show that these silty-clay or clayey-silty sands are fine sands and rarely medium sands, moderately to well sorted and rarely well sorted. The dominant granulometric facies is hyperbolic (sigmoid), with parabolic facies being rare. The primary mode of transport of these sands is saltation, which dominates rolling. The dispersion of points in the diagrams shows that these sands originate from two depositional environments: aeolian and fluvial. Morphoscopic analysis reveals the presence of clean rounded matt grains (RM), dirty rounded matt grains (RS), shiny blunt grains (EL) and shiny rounded grains (RL). The rounded matt grains exhibit several impact marks. The presence of dirty rounded grains with a ferruginous cement on their surface indicates that these sands have been reworked. These sands have undergone two types of transport, first by wind (aeolian environment) and then by water (fluvial environment).

Non-Darcy Flow in Molding Sands

Darcy’s law is widely used to describe the flow in porous media in which there is a linear relationship between fluid velocity and pressure gradient. However, it has been found that for high numbers of Reynolds this law ceases to be valid. In this work, the Ergun equation is employed to consider the non-linearity of air velocity with the pressure gradient in casting sands. The contribution of non-linearity to the total flow in terms of a variable defined as a non-Darcy flow fraction is numerically quantified. In addition, the influence of the shape factor of the sand grains on the non-linear flow fraction is analyzed. It is found that for values of the Reynolds number less or equal than 1, the contribution of non-linearity for spherical particles is around 1.15%.

A novel model for assessing the pore structure of tight sands and its application

Pore-structure poses great influence on the permeability and electrical property of tight sand reservoirs and is critical to the petrophysical research of such reservoirs.The uncertainty of permeability for tight sands is very common and the relationship between pore- structure and electrical property is often unclear.We propose a new parameterδ,integrating porosity,maximum radius of connected pore-throats,and sorting degree,for investigating the permeability and electrical properties of tight sands.Core data and wireline log analyses show that this newδcan be used to accurately predict the tight sands permeability and has a close relation with electrical parameters,allowing the estimation of formation factor F and cementation exponent m.The normalization of the resistivity difference caused by the pore- structure is used to highlight the influence of fluid type on Rt,enhancing the coincidence rate in the Pickett crossplot significantly.

Effects of moulding sands and wall thickness on microstructure and mechanical properties of Sr-modified A356 aluminum casting alloy

The effects of different cooling conditions on the mechanical properties and microstructures of a Sr-modified A356 （Al-7Si-0.3Mg） aluminum casting alloy were comparatively investigated using three moulding sands including quartz, alumina and chromite into multi-step blocks. The results show that the mechanical properties and microstructures using chromite sand are the best. As the cooling speed increases, the dendrite arm spacing （DAS） decreases significantly and the mechanical properties are improved, and the elongation is more sensitive to the cooling speed as compared with the tensile strength. The increase of the properties is primarily attributed to the decrease of the DAS and the increase of the free strontium atoms in the matrix. In particular, the regression models for predicting both the tensile strength and the elongation for Sr-modified A356 aluminum casting alloy were established based on the experimental data.

Study on Physical Properties and Related Spectral Characteristics of Composited Soil with Different Ratio of Feldspathic Sandstone and Sand

[Objective] To study the soil texture, water storage and related spectral characteristics of composited soil. [Method] 3 different ratios of composited soils was designed by using feldspathic sandstone and sand by 3 different ratios, 1：1（C1）, 1：2（C2） and 1：5（C3）, and the CK used loess soil and sand by 1：2, then the soil texture, water storage, soil and winter wheat spectral characteristic were measured and analyzed under those treatments in 2010-2013. [Result] （1） With the increasing of the plant- ing year, treatment C1, C2 and C3 all showed decreasing in the proportions of sand and increasing of silt and the CK showed decreasing of clay and increasing of sand, along 1-30 cm soil depth. Treatment C2 showed the proportion of sand, silt and clay were 76.69%, 18.72% and 4.70%, respectively. （2） The water contents of all the treatments were significant different from other in 0-60 cm soil depth, and showed increasing trend with the increasing of sand proportion. Treatment C2 had higher average water content during the 3 years than treatment CK, C1 and C3 by 21.34%, 11.59% and 3.91% in the same soil depth, respectively. （3） In 2013, the spectral reflection curve characters were similar for all treatment of winter wheat at the jointing stage and filling stage along the full-wave band （350-2 500 nm）, and the reflectance was higher in the jointing stage than the filling stage; the reflection peak was found around 550 nm, a part of green light wave band. Treatment C2 showed the highest canopy that all treatments had similar spectral curves, and the relative reflectance of soil increased during 350-1 750 nm wave length along with the increase of the sand proportion; for treatment CK, C1, C2 and C3, the soil spectral reflectance （y） and wave length （x） appeared highly correlated relationships, they were y=0.18 71 In（x）-0.979 4, y=0.158 7 In（x）-0.801 2, y=0.177 1 In（x）-0.910 8 and y=0.184 5 In（x）-0.944 5, respectively. [Conclusion] Synthesizing the soil physical properties and related spectral character indices, treatment C2 generated the best combination ratio of feldspathic sandstone and sand.

Development tendencies of moulding and core sands

Further development of the technology for making moulding and core sands will be strictly limited by tough requirements due to protection of the natural environment. These tendencies are becoming more and more tense, so that we will reach a point when even processes, that from technological point of view fulfill high requirements of the foundry industry, must be replaced by more ecologically-friendly solutions. Hence, technologies using synthetic resins as binding materials will be limited. This paper presents some predictable development tendencies of moulding and core sands. The increasing role of inorganic substances will be noticed, including silicate binders with significantly improved properties, such as improved knock-out property or higher reclamation strength. Other interesting solutions might also be moulding sands bonded by geo-polymers and phosphate binders or salts and also binders based on degradable biopolymers. These tendencies and the usefulness of these binders are put forward in this paper.

Influence of meandering river sandstone architecture on waterflooding mechanisms: a case study of the M-I layer in the Kumkol Oilfield, Kazakhstan

In order to explore the influence of sandstone architecture on waterflooding mechanisms using the architecture method,and taking as an example the M-I layer of the Kumkol oilfield in the South Turgay Basin,Kazakhstan,we portrayed the architecture features of different types of sandstones and quantitatively characterized heterogeneities in a single sand body in meandering river facies.Based on the waterflooding characteristics of point bar sand and overbank sand according to waterflooded interpretation results in 367 wells and numerical simulation results of well groups,we finally analyzed the remaining oil potential of the meandering river sandstone and pointed out its development directions at the high water cut stage.The result shows that because lateral accretion shale beds are developed inside single sand bodies,the point bar sand is a semi-connected body.The overbank sand is thin sandstone with poor connectivity,small area and fast lateral changes.The heterogeneity of the overbank sand is stronger than the point bar sand.The sandstone architectures control the waterflooding characteristics.In meandering river sandstones,the bottom of the point bar sand is strongly waterflooded,while the top of the point bar sand and most of the overbank sand are only weakly waterflooded or unflooded.The thickness percentage of unflooded zone and weakly waterflooded zone in point bar sand is 40％,and the remaining oil in its top part is the main direction for future development.

Heavy Oil and Oil Sands:Global Distribution and Resource Assessment

Global recoverable resources of heavy oil and oil sands have been assessed by CNPC using a geology-based assessment method combined with the traditional volumetric method, spatial interpolation method, parametric-probability method etc. The most favourable areas for exploration have been selected in accordance with a comprehensive scoring system. The results show:(1) For geological resources, CNPC estimate 991.18 billion tonnes of heavy oil and 501.26 billion tonnes of oil sands globally, of which technically recoverable resources of heavy oil and oil sands comprise 126.74 billion tonnes and 64.13 billion tonnes respectively. More than 80% of the resources occur within Tertiary and Cretaceous reservoirs distributed across 69 heavy oil basins and 32 oil sands basins. 99% of recoverable resources of heavy oil and oil sands occur within foreland basins, passive continental-margin basins and cratonic basins.(2) Since residual hydrocarbon resources remain following large-scale hydrocarbon migration and destruction, heavy oil and oil sands are characterized most commonly by late hydrocarbon accumulation, the same basin types and source-reservoir conditions as for conventional hydrocarbon resources, shallow burial depth and stratabound reservoirs.(3) Three accumulation models are recognised, depending on basin type: degradation along slope; destruction by uplift; and migration along faults.(4) In addition to mature exploration regions such as Canada and Venezuela, the Volga-Ural Basin and the Pre-Caspian Basin are less well-explored and have good potential for oil-sand discoveries, and it is predicted that the Middle East will be an important region for heavy oil development.

Effects of laser energy density on forming accuracy and tensile strength of selective laser sintering resin coated sands

Baozhu sand particles with size between 75 μm and 150 μm were coated by resin with the ratio of 1.5 wt.% of sands. Laser sintering experiments were carried out to investigate the effects of laser energy density(E = P/v), with different laser power(P) and scanning velocity(v), on the dimensional accuracy and tensile strength of sintered parts. The experimental results indicate that with the constant scanning velocity, the tensile strength of sintered samples increases with an increase in laser energy density; while the dimensional accuracy apparently decreases when the laser energy density is larger than 0.032 J·mm-2. When the laser energy density is 0.024 J·mm-2, the tensile strength shows no obvious change; but when the laser energy density is larger than 0.024 J·mm-2, the sample strength is featured by the initial increase and subsequent decrease with simultaneous increase of both laser power and scanning velocity. In this study, the optimal energy density range for laser sintering is 0.024-0.032 J·mm-2. Moreover, samples with the best tensile strength and dimensional accuracy can be obtained when P = 30-40 W and v = 1.5-2.0 m·s-1. Using the optimized laser energy density, laser power and scanning speed, a complex coated sand mould with clear contour and excellent forming accuracy has been successfully fabricated.

A sand production prediction model for weak sandstone reservoir in Kazakhstan

Weakly consolidated reservoirs are prone to sand production problem,which can lead to equipment damages and environmental issues.The conditions for sand production depend on stresses and properties of rock and fluid.Accurate sand volume estimation is,however,still a challenging issue,especially for reservoirs in weak formations.The weak reservoirs containing viscous or heavy oil are mainly discovered in shallow depths in Kazakhstan,with moderate temperature and pressure.Many prediction models developed for open-hole completions where the reservoir materials usually possess certain strength are not applicable for the local reservoirs where the materials are significantly weaker even if casing is used to support the wellbore with oil produced through the perforation tunnels.In this context,a prediction model was proposed where the volume of the produced sand was estimated as the volume of the plastic zone of the failed materials surrounding the perforation tunnels.The model assumes an evolving truncated conical shape for the damage zone and takes into account stress distributions and shear failure in this zone.Then,the proposed model was used to estimate sand volumes in 20 wells during oil production with sequential increase of flow rates.The predictions match well with the measured sand volumes in a local oil field.Finally,a sensitivity analysis was conducted on the model performance.It shows that the permeability of the plastic zone was the most significant controlling factor in the prediction results.

Performance comparison of novel chemical agents in improving oil recovery from tight sands through spontaneous imbibition

Tight sands are abundant in nanopores leading to a high capillary pressure and normally a low fluid injectivity.As such,spontaneous imbibition might be an effective mechanism for improving oil recovery from tight sands after fracturing.The chemical agents added to the injected water can alter the interfacial properties,which could help further enhance the oil recovery by spontaneous imbibition.This study explores the possibility of using novel chemicals to enhance oil recovery from tight sands via spontaneous imbibition.We experimentally examine the effects of more than ten different chemical agents on spontaneous imbibition,including a cationic surfactant(C12 TAB),two anionic surfactants(0242 and 0342),an ionic liquid(BMMIM BF4),a high pH solution(NaBO2),and a series of house-made deep eutectic solvents(DES3-7,9,11,and 14).The interfacial tensions(IFT)between oil phase and some chemical solutions are also determined.Experimental results indicate that both the ionic liquid and cationic surfactant used in this study are detrimental to spontaneous imbibition and decrease the oil recovery from tight sands,even though cationic surfactant significantly decreases the oil-water IFT while ionic liquid does not.The high pH NaBO2 solution does not demonstrate significant effect on oil recovery improvement and IFT reduction.The anionic surfactants(O242 and O342)are effective in enhancing oil recovery from tight sands through oil-water IFT reduction and emulsification effects.The DESs drive the rock surface to be more water-wet,and a specific formulation(DES9)leads to much improvement on oil recovery under counter-current imbibition condition.This preliminary study would provide some knowledge about how to optimize the selection of chemicals for improving oil recovery from tight reservoirs.

Biodegradation and origin of oil sands in the Western Canada Sedimentary Basin

The oil sands deposits in the Western Canada Sedimentary Basin （WCSB） comprise of at least 85% of the total immobile bitumen in place in the world and are so concentrated as to be virtually the only such deposits that are economically recoverable for conversion to oil. The major deposits are in three geographic and geologic regions of Alberta： Athabasca, Cold Lake and Peace River. The bitumen reserves have oil gravities ranging from 8 to 12° API, and are hosted in the reservoirs of varying age, ranging from Devonian （Grosmont Formation） to Early Cretaceous （Mannville Group）. They were derived from light oils in the southern Alberta and migrated to the north and east for over 100 km during the Laramide Orogeny, which was responsible for the uplift of the Rocky Mountains. Biodegradation is the only process that transforms light oil into bitumen in such a dramatic way that overshadowed other alterations with minor contributions. The levels of biodegradation in the basin increasing from west （non-biodegraded） to east （extremely biodegraded） can be attributed to decreasing reservoir temperature, which played the primary role in controlling the biodegradation regime. Once the reservoir was heated to approximately 80℃, it was pasteurized and no biodegradation would further occur. However, reservoir temperature could not alone predict the variations of the oil composition and physical properties. Compositional gradients and a wide range ofbiodegradation degree at single reservoir column indicate that the water-leg size or the volume ratio of oil to water is one of the critical local controls for the vertical variations ofbiodegradation degree and oil physical properties. Late charging and mixing of the fresh and degraded oils ultimately dictate the final distribution of compositions and physical properties found in the heavy oil and oil sand fields. Oil geochemistry can reveal precisely the processes and levels that control these variations in a given field, which opens the possibility of model-driven prediction of oil properties and sweet spots in reservoirs.

Feasibility study of tar sands conditioning for earth pressure balance tunnelling

This paper presents the results of laboratory test on the feasibility of soil conditioning for earth pressurebalance （EPB） excavation in a tar sand, which is a natural material never studied in this respect. Thelaboratory test performed is based on a procedure and methods used in previous studies with differenttypes of soils, but for this special complex material, additional tests are also conducted to verify particularproperties of the tar sands, such as the tilt test and vane shear test usually used in cohesive materials, anda direct shear test. The laboratory test proves that the test procedure is applicable also to this type of soiland the conditioned material can be considered suitable for EPB excavations, although it is necessary touse a certain percentage of fine elements （filler） to create a material suitable to be mixed with foam. Thetest results show that the conditioned material fulfils the required standard for an EPB application.