Influence of heat treatment on microstructure and mechanical properties of FeCrNi coating produced by laser cladding

The FeCrNi alloy powders were used on the dovetail groove of FV520B steel to fabricate the multilayer laser cladding layers. The effects of heat treatment on the microstructure and mechanical properties of FeCrNi layers were investigated. The results showed that the heat treatment at the temperature ranged from 1073 to 1273 K refined the grains of the substrate materials and removed the soft zone of hardness between the fused zone (FZ) and base material (BM) effectively mainly due to a secondary quench of heat treatment. When the temperature of heat treatment was 1073 K, the maximum ultimate tensile strength (UTS) values of the laser cladding component were obtained. However, the heat treatment at high temperature had a bad effect on wear resistance of coatings at some extent.

Effect of high-speed laser cladding on microstructure and corrosion resistance of CoCrFeNiMo_(0.2) high-entropy alloy

In order to study the corrosion resistance of high-speed laser cladding(HLC) coating while improving production efficiency,a CoCrFeNiMo_(0.2)high-entropy alloy(HEA) coating was prepared by HLC.The optimized parameters of HLC are laser power of 880 W,scanning speed of 18 m/min,overlapping ratio of 60%,and powder feed speed of 3 r/min.Then,the surface roughness,microstructure,phase composition,element distribution,and electrochemical properties in 3.5 wt% NaCl solution of the coatings were analyzed,respectively.The local surface roughness of the CoCrFeNiMo_(0.2)HEA coating was found to be 15.53 μm.A distinct metallurgical bond could be observed between the coating and the substrate.Compared to the conventional laser cladding(CLC),the results of electrochemical tests showed that CoCrFeNiMo_(0.2)HEA coating exhibited a significant passivation.The corrosion current density of 5.4411 × 10^(-6)A·cm^(-2) and the corrosion potential of-0.7445 V for the HLC coating were calculated by the Tafel extrapolation method.The CLC coating’s corrosion current density and corrosion potential are 2.7083×10^(-5)A·cm^(-2) and-0.9685 V,respectively.The HLC coating shows a superior corrosion resistance,crucially due to the uniform and fine grains.Under various complex and harsh working conditions,this method can be widely used in the field of repairing and remanufacturing of corro sion-proof workpiece s.

Influence of yttrium on microstructure and properties of Ni—Al alloy coatings prepared by laser cladding

NieAl alloy coatings with different Y additions are prepared on 45#medium steel by laser cladding. The influence of Y contents on the microstructure and properties of NieAl alloy coatings is investigated using X-ray diffraction, scanning electron microscopy, electron probe microanalyzer, Vickers hardness tester, friction wear testing machine, and thermal analyzer. The results show that the cladding layers are mainly composed of NiAl dendrites, and the dendrites are gradually refined with the increase in Y additions. The purification effect of Y can effectively prevent Al2O3oxide from forming. However, when the atomic percent of Y addition exceeds 1.5%, the extra Y addition will react with O to form Y2O3oxide, even to form Al5Y3O12oxide, depending on the amount of Y added. The Y addition in a range of 1.5e3.5 at.% reduces the hardness and anti-attrition of cladding layer, but improves obviously its wear and oxidation resistances.

Effect of Laser Cladding Al Ni TiC Powder on Microstructure and Properties of Aluminum Alloy

In this paper, Al/Ni/TiC powders were mixed on the surface of A380 aluminum alloy, by selecting appropriate laser parameters;the cladding layer with good adhesion to the substrate was obtained. The microstructure and properties of the cladding layer under different laser parameters were analyzed. The results show that: the phase composition of the cladding layer is mainly composed of TiC, Al, Ni, C and Ti phases. The hardness of the cladding region is up to 173.3 HV, which is about 2.9 times the matrix (–59.1 HV). The corrosion voltage (–1.8 V) of the cladding layer shifted significantly from the corrosion potential (–1.18 V), the corrosion current density increased, the resistance value decreased and the diameter of the capacitor arc decreased;all these phenomena indicate that the corrosion resistance of the cladding layer is decreased.

Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Laser Cladding

21-4N(5Cr21Mn9Ni4N)is extensively employed in the production of engine valves,operating under severe conditions.Apart from withstanding high-temperature gas corrosion,it must also endure the impact of cylinder explosion pressure.The predominant failure mode of 21-4N valves is abrasive wear.Surface coatings serve as an effective approach to prevent such failures.In this investigation,Laser cladding technology was utilized to fabricate AlCoCrFeNiTi high entropy alloy coatings onto the surfaces of 21-4N valves.According to the findings,the cladding zone has a normal dendritic microstructure,a good substrate-to-cladding layer interaction,and no obvious flaws.In terms of hardness,the cladding demonstrates an average hardness of 620 HV.The hardness has increased by 140%compared to the substrate.The average hardness of the cladding remains at approximately 520 HV even at elevated temperatures.Regarding frictional wear performance,between 400℃and 800℃,the cladding layer exhibits an average friction coefficient of 0.4,with the primary wear mechanisms being abrasive wear,adhesive wear,and a minor degree of plastic deformation.

Unveiling the cellular microstructure-property relations in martensitic stainless steel via laser powder bed fusion

Laser powder bed fusion(LPBF)is a widely recognized additive manufacturing technology that can fabricate complex components rapidly through layer-by-layer formation.However,there is a paucity of research on the effect of laser scanning speed on the cellular microstructure and mechanical properties of martensitic stainless steel.This study systematically investigated the influence of laser scanning speed on the cellular microstructure and mechanical properties of a developed Fe11Cr8Ni5Co3Mo martensitic stainless steel produced by LPBF.The results show that increasing the laser scanning speed from 400 to 1000 mm/s does not lead to a noticeable change in the phase fraction,but it reduces the average size of the cellular microstructure from 0.60 to 0.35μm.The scanning speeds of 400 and 1000 mm/s both had adverse effects on performances of sample,resulting in inadequate fusion and keyhole defects respectively.The optimal scanning speed for fabricating samples was determined to be 800 mm/s,which obtained the highest room temperature tensile strength and elongation,with the ultimate tensile strength measured at(1088.3±2.0)MPa and the elongation of(16.76±0.10)%.Furthermore,the mechanism of the evolution of surface morphology,defects,and energy input were clarified,and the relationship between cellular microstructure size and mechanical properties was also established.

Microstructure and high temperature tribological behavior of laser cladding Ni60A alloys coatings on 45 steel substrate

The crack-free Ni60 A coating was fabricated on 45 steel substrate by laser cladding and the microstructure including solidification characteristics, phases constitution and phase distribution was systematically investigated. The high temperature friction and wear behavior of the cladding coating and substrate sliding against GCr15 ball under different loads was systematically evaluated. It was found that the coating has homogenous and fine microstructure consisting of γ（Ni） solid solution, a considerable amount of network Ni-Ni3 B eutectics, m^23C6 with the floret-shape structure and Cr B with the dark spot-shape structure uniformly distributing in interdendritic eutectics. The microhardness of the coating is about 2.6 times as much as that of the substrate. The coating produces higher friction values than the substrate under the same load condition, but the friction process on the coating keeps relatively stable. Wear rates of the coating are about 1/6.2 of that of the substrate under the higher load（300 g）. Wear mechanism of the substrate includes adhesion wear, abrasive wear, severe plastic deformation and oxidation wear, while that of the coating is merely a combination of mild abrasive wear and moderate oxidation wear.

Microstructure and Fractural Morphology of Cobalt-based Alloy Laser Cladding

The solidification features,micro segregation,and fracture characteristics of cobalt based alloy on the substrate of 20CrMo steel by laser cladding were studied by using electron microscopy.Experimental results show that the fine columnar grains and cellular dendrite grains are obtained which are perpendicular to the coating/substrate interface;the primary arms are straight while the side branches are degenerated;the microstructure consists of primary face centered cubic (fcc) Co dendrites and a network of Cr enriched eutectic M23C6 (M=Cr,W,Fe) carbides;the micro segregation is severe for the rapid heating and cooling of laser cladding;the typical brittle intergranular fracture occurs in cobalt based laser cladding layer.

Microstructure and mechanical properties of Ni-based composite coatings reinforced by in situ synthesized TiB_2 + TiC by laser cladding

A Ni-based composite coating reinforced by in situ synthesized TiB2 and TiC particles was fabricated on Ti6A14V by laser cladding. An attempt was made to correlate the thermodynamic predictions and experimental observation. The micro- structure and the microhardness profile across the coating were investigated by means of X-ray diffraction （XRD）, scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and a hardness tester. It is found that the coating mainly consists of a large number of reinforcements （black blocky TiB2, flower-like or equiaxial TiC, and fine acicular CrB） and the 7 matrix. The hardness of TiB2, TiC, and CrB reinforcements is much higher than that of the 7 matrix. The dispersive distribu- tion of such high hardness reinforcements causes the increase in hardness of the whole coating. The average value of the hard- ness is approximately Hv0.2 700 in the coating. The hardness of the coating is obviously higher than that of the substrate due to the dispersion strengthening of reinforcements.

Microstructure and Thermal Physical Parameters of Ni60-Cr_3C_2 Composite Coating by Laser Cladding

To satisfy performance and long life requirements for hot forging die,Ni60-Cr3C2 composite coatings were prepared on the high-speed steel W6Mo5Cr4V2 using laser cladding technology.Laser clad coatings with different ratios of Ni60：Cr3C2 were investigated by scanning electron microscopy（SEM）,X-ray diffraction（XRD）,energy-dispersive X-ray analysis（EDX） and micro-hardness tester,respectively.Specific heat capacity and thermal conductivity were measured by Laser Thermal Constant Meter.Thermal expansion coefficient and elastic modulus were measured by Dynamic Mechanical Thermal Analyzer and Electro-Hydraulic Servocontrolled Testing System,respectively.The results indicated that Ni60＋50wt% Cr3C2 composite coating had dense and homogeneous structure,as well as a metallurgical bonding with the substrate.With the increase of Cr3C2 content,volume of chromium-containing compounds in the composite coating increased,microhardness increased and microstructure refined.The thermal physical parameters results showed that Ni60＋50wt% Cr3C2 composite coating was overall worse than W6Mo5Cr4V2,but had a higher hot yield strength to alleviate hot fatigue and surface hot wear of hot forging die during hot forging and thus improve the service life of hot forging die.

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12 Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12 Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M3 W3 C(M=Fe,Co) were formed. Meanwhile, WC-12 Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of(2.15±0.31)×10-7 mm3/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.

Microstructure,microhardness and corrosion resistance of laser cladding Ni−WC coating on AlSi5Cu1Mg alloy

The microstructure,microhardness,and corrosion resistance of laser cladding Ni−WC coating on the surface of AlSi5Cu1Mg alloy were investigated by scanning electron microscopy,X-ray diffraction,microhardness testing,immersion corrosion testing,and electrochemical measurement.The results show that a smooth coating containing NiAl,Ni_(3)Al,M_(7)C_(3),M_(23)C_(6)phases(M=Ni,Al,Cr,W,Fe)and WC particles is prepared by laser cladding.Under a laser scanning speed of 120 mm/min,the microhardness of the cladding coating is 9−11 times that of AlSi5Cu1Mg,due to the synergistic effect of excellent metallurgical bond and newly formed carbides.The Ni−WC coating shows higher corrosion potential(−318.09 mV)and lower corrosion current density(12.33μA/cm^(2))compared with the matrix.The crack-free,dense cladding coating obviously inhibits the penetration of Cl^(−)and H^(+),leading to the remarkedly improved corrosion resistance of cladding coating.

Microstructure and wear behavior of laser cladding Ni-based alloy composite coating reinforced by Ti(C,N) particulates

In this paper, Ni-based alloy composite coating reinforced by Ti （C, N） particles was fabricated on the mild steel through laser cladding technology. The microstrncture of laser cladding layer was analyzed by means of optical microscopy （OM）, X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The wear resistance test of the coating was evaluated using an M-2000 tester. The results showed that the Ni-based composite coating had an ability of rapid solidification to form dendritic crystals microstructure consisting of Ti （ C, N） particulates uniformly distributed in the matrix. It was found that some Ti（ C,N） particles are similar to be round in shape, and the others are irregular. Laser cladding layer reinforced by Ti（ C, N） particulates was found to possess good wear resistance property.

Microstructures and properties of Fe-Co-B-Si-Nb coating prepared by laser cladding and remelting

High power laser cladding of [ （ Fe0. 5 Co0. 5 ） 0. 75 B0. 2 Si0.05 ] 95. 7 Nb4. 3 powder mixture afier-remelting was performed to fabricate Fe-based metallic glass coating on the surface of steel of China Classification Society： Grade B （CCS-B）. Scanning electron microscopy （SEM）, X-ray diffraction （XRD）, transmission electron microscopy （TEM） with energy dispersive spectrometer （EDS）, Vickers hardness tester and corrosion resistance tester were employed to characterize microstructures and evaluate properties of this coating. According to the results of SEM, XRD and TEM, the cladding coating consisted of nanocrystalline embedded in amorphous phase. EDS data indicated that Nb segregated in the amorphous matrix. The results of hardness test revealed that the hardness of the top layer was higher than that of the inner layer of the coating. The coating exhibited excellent corrosion resistance in a 3.5% NaCl solution.

Microstructure and wear resistance of AlCrFeNiMo_(0.5)Si_(x) high-entropy alloy coatings prepared by laser cladding

In recent years,the coating prepared by laser cladding has attracted much attention in the field of wear research.In this work,AlCrFeNiMo_(0.5)Si_(x)(x=0,0.5,1.0,1.5,2.0)high-entropy alloy coatings were designed and prepared on Q235 steel by laser cladding.The effect of Si content on microstructure,microhardness and wear resistance of the coatings was studied in detail.The results indicate that the AlCrFeNiMo_(0.5)Si_(x) highentropy alloy coatings show an excellent bonding between substrate and the cladding layer.The AlCrFeNiMo_(0.5)Si_(x) coatings are composed of nano-precipitated phase with BCC structure and matrix with ordered B2 structure.With the addition of Si,the white phase(Cr,Mo)_(3)Si with cubic structure appears in the interdendritic,and the morphology of the coating(x=2.0)transforms into lamellar eutectic-like structures.The addition of Si enhances the microhardness and significantly improves the wear resistance of the coatings.As x increases from 0 to 2.0,the average hardness of the cladding zone increases from 632 HV to 835 HV,and the wear rate decreases from 1.64×10^(-5) mm^(3)·(N·m)^(-1) to 5.13×10^(-6) mm^(3)·(N·m)^(-1).When x≥1.5,the decreasing trend of the wear rate gradually slows down.The wear rates of Si1.5 and Si2.0 coatings are 5.85×10^(-6) mm^(3)·(N·m)^(-1) and 5.13×10^(-6) mm^(3)·(N·m)^(-1),respectively,which is an order of magnitude lower than that of Q235 steel.

Microstructure and abrasion wear behavior of Ni-based laser cladding alloy layer at high temperature

Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21+20%WC+0.5%CeO2, Ni25+20%WC+0.5%CeO2 and Ni60+20%WC+0.5%CeO2, the experimental results show that Ni21+20%WC+ 0.5%CeO2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.

Microstructure and performance of laser cladding TiB_2 and Nickel-coated graphite composite coating on stainless steel 9Cr18

The antiwear and antifriction coating, which contains TiB2 and Nickel-coated graphite, has been obtained on stainless steel 9Cr18 by laser cladding. The processing method, microstructure, interface, microhardness, tribological properties and the forming mechanisms of the coating are analyzed. Results show that the microstructure of the clad coating are mainly long plume-like primary phase sosoloid Ni-Fe which form the matrix framework, while the in-situ anomalous synthetical TiC grains and uhrafine TiB2 grains uniformly disperse among the framework. The hardness and wear resistance of the coating has been greatly improved, which can be attributed to the reinforcement mechanism of TiC, TiB2, FeC, Fe3C and Cr23 C6. etc. At the same time, the coating has friction-reducing ability.

Effect of Y_(2)O_(3) on microstructure and properties of CoCrFeNiTiNb high entropy alloy coating on Ti-6Al-4V surface by laser cladding

The effects of Y_(2)O_(3) on the microstructure, microhardness, wear resistance, high-temperature oxidation resistance, hot corrosion resistance, and electrochemical corrosion behaviour of CoCrFeNiTiNb high entropy alloy coatings formed on Ti-6Al-4V alloy surfaces were studied. The results show that the addition of Y_(2)O_(3) changes the proportion of the phase but does not change its type. The average grain size is only 1/4.7 of that of the high entropy alloy(HEA) coating, and the fine-grained strengthening leads to increases in the microhardness and wear resistance of 21.8% and 26.9%, respectively. The addition of Y_(2)O_(3) enhances the denseness and bonding properties of the oxide and corrosion product layers, reducing the oxidation and hot corrosion rates by 60.3% and 40.3%, respectively. The addition of Y_(2)O_(3) doubles the corrosion resistance which is attributed to the refinement of the grains, the increased proportion of HCP and TiN, and the weakening of galvanic coupling corrosion.

Microstructure & performance of laser cladding on pick surface of coal mining machine

Laser cladding of 316 L steel powders on pick substrate of coal mining machine was conducted, and microstructure of laser cladding coating was analyzed. The micro-hardness of laser cladding coating was examined. The results show that microstructure of laser cladding zone is exiguous dentrite, and there are hard spots dispersible distribution in the laser cladding zone. Performances of erode-resistant, surface micro-hardness and wear-resistant are improved obviously.

Microstructure and Mechanical Property of Al-Cu-Li Alloy Joint by Laser Welding with Filler Wire

The Al-Cu-Li alloy is welded by using laser beam welding,and the welding wire ER4043 is used as filler metal. The microstructure and mechanical property of welded joints are systematically investigated. Microstructure analyses show that the fusion zone is mainly composed of α-Al matrix phase and some strengthening phases including T,δ’,θ’,β’ and T1,etc. During welding,the weld formation and joint quality are obviously improved by the addition of Al-Si filler wire. The measurements of mechanical property indicate that,compared with that of the base metal(BM), the microhardness in the weld zone is decreased to a certain extent. Under the appropriate welding parameters,the tensile strength of welded joint reaches 369.4 MPa,which is 67.8% of that of the BM. There are many dimples on the joint fracture surface,and it mainly presents the fracture characteristic of dimple aggregation.