Fine-grained ZK60 magnesium alloy sheets of 2.0 mm in thickness were successfully joined by laser beam welding （LBW）. The effects of welding parameters including laser power and welding speed on the microstructures ...Fine-grained ZK60 magnesium alloy sheets of 2.0 mm in thickness were successfully joined by laser beam welding （LBW）. The effects of welding parameters including laser power and welding speed on the microstructures and mechanical properties of the joints were investigated. A sound bead, with the ultimate tensile strength （UTS） of 300 MPa and elongation of 12.0%, up to 92.5% and 65% of those of the base metal, respectively, is obtained with the optimized welding parameters. No liquation cracking is visible in the partially melted zone （PMZ） owing to the inhibitory action of the fine dispersed precipitates and the fine-grained microstructure in the as-rolled magnesium alloy sheets. The fusion zone （FZ） is featured with the equiaxed dendritic grains of the average grain size about 8 μm, which are similar to those in the heat affected zone （HAZ）, and this contributes to the relatively high joint efficiency.展开更多
Various heat treatments were conducted on Inconel 718 superalloy,and the resultant microstructures and properties were investigated to analyze the mechanisms of heat treatments.Results show that the type and quantity ...Various heat treatments were conducted on Inconel 718 superalloy,and the resultant microstructures and properties were investigated to analyze the mechanisms of heat treatments.Results show that the type and quantity of precipitate phases and the grain size have different effects on the properties of Inconel 718 superalloy after various heat treatments.Theγ"andγ'phases as well as grain size mainly influence the strength,and theδphase mainly influences the plasticity.Besides,the precipitation ofγ"andγ'strengthening phases can improve the yield strength.The alloy strength is inversely proportional to mean grain size when theγ"andγ'phases have similar contents.The plasticity is susceptible to the content and shape ofδphase.A proper amount ofδphase is beneficial to the plasticity,but excessiveδphase degrades plasticity.展开更多
The austenite grain growth behavior of Q1030 steel was studied under different heating conditions. The austenite grain size increases with the heating temperature and holding time increasing. Austenite grains grow in ...The austenite grain growth behavior of Q1030 steel was studied under different heating conditions. The austenite grain size increases with the heating temperature and holding time increasing. Austenite grains grow in an exponential manner with rising heating tem- perature and in a parabolic manner with prolonging holding time. A mathematical model for describing the austenite grain growth behavior of Q 1030 steel was obtained on the basis of experimental results using regression analysis. When the heating temperatures lie between 1000 and 1100℃ at a certain holding time, abnormal grain growth appears, which causes mixed grains in Q1030 steel.展开更多
The preliminary chemical composition optimization and heat treatment parameters of Inconel 740H were investigated systematically. Six heats of experimental alloys （designated as heat 401 to heat 406） with varied che...The preliminary chemical composition optimization and heat treatment parameters of Inconel 740H were investigated systematically. Six heats of experimental alloys （designated as heat 401 to heat 406） with varied chemi- cal compositions were subjected to standard heat treatment at four different solution temperatures. Due to its superi- or combination of strength, ductility, and toughness together with its minor mechanical property changes at different solution temperatures, heat 405 was chosen as an optimized one to conduct further heat treatment investigations. The evolution of grain size with solution temperature for heat 405 was studied and the optimal solution temperature was determined. After solution treatment at the optimal temperature, four different cooling rates were applied to investi- gate the effect of cooling rate on the size distribution modal and mean radius of the γ′ precipitates. No bi-modal size distribution of γ′ precipitates was found for all cooling rates and water cooling was recommended for Inconel 740H. In addition, the effect of pre-aging at 800 ℃ for 16 h on the microstrueture of Inconel 740H aged for a long time was studied. It is found that pre-aging at 800 ℃ would result in bi-modal size distribution of γ′ precipitates after long time aging at 750 ℃ compared with mono modal size distribution in samples without pre-aging, which might be caused by the difference in initial size distribution modal before Ostwald ripening of γ′ precipitates in samples with and without pre-aging at 800 ℃.展开更多
In order to research the effect of microalloying Nb,the microstructure and heat treatment distortion of case carburizing steels with and without Nb addition are compared.Results show that a uniform and fine prior aust...In order to research the effect of microalloying Nb,the microstructure and heat treatment distortion of case carburizing steels with and without Nb addition are compared.Results show that a uniform and fine prior austenite grain size was obtained for the steel with the addition of 0.03 wt.%Nb even after being carburized at 980℃for 37 h,resulting in a very deep hardened layer of about 4 mm.Nb is an effective microalloying element to hinder austenite grain growth of gears during high-temperature carburizing.Theoretical calculation and experimental observation of NbC precipitates indicate that fine NbC precipitates have not evidently dissolved at 980℃,and thus they can act as grain refiners due to pinning effect.Heat treatment distortion of Nb-added steel is much lower than that of the steel without Nb addition.It may be contributed to its fine and uniform grain size,which presumably influences stress during martensitic transformation.展开更多
基金Project(51274092)supported by the National Natural Science Foundation of ChinaProject(20120161110040)supported by the Doctoral Program of Higher Education of China
文摘Fine-grained ZK60 magnesium alloy sheets of 2.0 mm in thickness were successfully joined by laser beam welding （LBW）. The effects of welding parameters including laser power and welding speed on the microstructures and mechanical properties of the joints were investigated. A sound bead, with the ultimate tensile strength （UTS） of 300 MPa and elongation of 12.0%, up to 92.5% and 65% of those of the base metal, respectively, is obtained with the optimized welding parameters. No liquation cracking is visible in the partially melted zone （PMZ） owing to the inhibitory action of the fine dispersed precipitates and the fine-grained microstructure in the as-rolled magnesium alloy sheets. The fusion zone （FZ） is featured with the equiaxed dendritic grains of the average grain size about 8 μm, which are similar to those in the heat affected zone （HAZ）, and this contributes to the relatively high joint efficiency.
基金National Natural Science Foundation of China(52175353)Shanxi Province Patent Conversion Special Plan Program(202201001)Shanxi Province Key Research and Development Program(202102150401002)。
文摘Various heat treatments were conducted on Inconel 718 superalloy,and the resultant microstructures and properties were investigated to analyze the mechanisms of heat treatments.Results show that the type and quantity of precipitate phases and the grain size have different effects on the properties of Inconel 718 superalloy after various heat treatments.Theγ"andγ'phases as well as grain size mainly influence the strength,and theδphase mainly influences the plasticity.Besides,the precipitation ofγ"andγ'strengthening phases can improve the yield strength.The alloy strength is inversely proportional to mean grain size when theγ"andγ'phases have similar contents.The plasticity is susceptible to the content and shape ofδphase.A proper amount ofδphase is beneficial to the plasticity,but excessiveδphase degrades plasticity.
文摘The austenite grain growth behavior of Q1030 steel was studied under different heating conditions. The austenite grain size increases with the heating temperature and holding time increasing. Austenite grains grow in an exponential manner with rising heating tem- perature and in a parabolic manner with prolonging holding time. A mathematical model for describing the austenite grain growth behavior of Q 1030 steel was obtained on the basis of experimental results using regression analysis. When the heating temperatures lie between 1000 and 1100℃ at a certain holding time, abnormal grain growth appears, which causes mixed grains in Q1030 steel.
基金Sponsored by High-Tech Research and Development Project of China(2102AA03A501)
文摘The preliminary chemical composition optimization and heat treatment parameters of Inconel 740H were investigated systematically. Six heats of experimental alloys （designated as heat 401 to heat 406） with varied chemi- cal compositions were subjected to standard heat treatment at four different solution temperatures. Due to its superi- or combination of strength, ductility, and toughness together with its minor mechanical property changes at different solution temperatures, heat 405 was chosen as an optimized one to conduct further heat treatment investigations. The evolution of grain size with solution temperature for heat 405 was studied and the optimal solution temperature was determined. After solution treatment at the optimal temperature, four different cooling rates were applied to investi- gate the effect of cooling rate on the size distribution modal and mean radius of the γ′ precipitates. No bi-modal size distribution of γ′ precipitates was found for all cooling rates and water cooling was recommended for Inconel 740H. In addition, the effect of pre-aging at 800 ℃ for 16 h on the microstrueture of Inconel 740H aged for a long time was studied. It is found that pre-aging at 800 ℃ would result in bi-modal size distribution of γ′ precipitates after long time aging at 750 ℃ compared with mono modal size distribution in samples without pre-aging, which might be caused by the difference in initial size distribution modal before Ostwald ripening of γ′ precipitates in samples with and without pre-aging at 800 ℃.
基金the Ministry of Science and Technology(MOST)of China under the contract of No.2016YFB0300102The financial support from CITIC Metals is also acknowledged.
文摘In order to research the effect of microalloying Nb,the microstructure and heat treatment distortion of case carburizing steels with and without Nb addition are compared.Results show that a uniform and fine prior austenite grain size was obtained for the steel with the addition of 0.03 wt.%Nb even after being carburized at 980℃for 37 h,resulting in a very deep hardened layer of about 4 mm.Nb is an effective microalloying element to hinder austenite grain growth of gears during high-temperature carburizing.Theoretical calculation and experimental observation of NbC precipitates indicate that fine NbC precipitates have not evidently dissolved at 980℃,and thus they can act as grain refiners due to pinning effect.Heat treatment distortion of Nb-added steel is much lower than that of the steel without Nb addition.It may be contributed to its fine and uniform grain size,which presumably influences stress during martensitic transformation.
