Surface Integrity of Inconel 738LC Parts Manufactured by Selective Laser Melting Followed by High-speed Milling

This study is concerned with the surface integrity of Inconel 738LC parts manufactured by selective laser melting(SLM)followed by high-speed milling(HSM).In the investigation process of surface integrity,the study employs ultradepth three-dimensional microscopy,laser scanning confocal microscopy,scanning electron microscopy,electron backscatter diffractometry,and energy dispersive spectroscopy to characterize the evolution of material microstructure,work hardening,residual stress coupling,and anisotropic effect of the building direction on surface integrity of the samples.The results show that SLM/HSM hybrid manufacturing can be an effective method to obtain better surface quality with a thinner machining metamorphic layer.High-speed machining is adopted to reduce cutting force and suppress machining heat,which is an effective way to produce better surface mechanical properties during the SLM/HSM hybrid manufacturing process.In general,high-speed milling of the SLM-built Inconel 738LC samples offers better surface integrity,compared to simplex additive manufacturing or casting.

Laser surface melting AZ31B magnesium alloy with liquid nitrogen-assisted cooling

Laser surface melting（LSM） is a high-energy surface treatment that allows modification of the microstructure and surface properties of Mg alloys. In the present work, an attempt of LSM on magnesium alloy with liquid nitrogen-assisted cooling（LNSC） was carried out to get the higher cooling rate and improve the surface properties. The experimental results were compared with those of Ar gas protection at room temperature. The samples after LSM with LNSC resulted in a thinner melted layer, a highly homogeneous, refined melted microstructure and formed a lot of worm-like nanocrystals and local amorphous structures. Microhardness of the melted layer with LNAC was improved to HV 90-148 as compared to HV 65-105 of the samples with Ar gas protection. The corrosion resistance of the melted layer in a 3.5% Na Cl solution（mass fraction） was improved because of the grain refinement and redistribution of β-Mg17Al12 phases following rapid quenching associated with the process.

Tensile behavior of Ti-6Al-4V alloy fabricated by selective laser melting: effects of microstructures and as-built surface quality

Selective laser melting （SLM） is a powerful additive manufacturing （AM） technology, of which the most prominent advantage is the ability to produce components with a complex geometry. The service performances of the SLM-processed components depend on the microstructure and surface quality. In this work, the microstructures, mechanical properties, and fracture behaviors of SLM-processed Ti-6AI-4V alloy under machined and as-built surfaces after annealing treatments and hot isostatic pressing （HIP） were investigated. The microstructures were analyzed by optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscopy （TEM）. The mechanical properties were measured by tensile testing at room temperature. The results indicate that the as-deposited microstructures are characterized by columnar grains and fine brittle martensite and the as- deposited properties present high strength, low ductility and obvious anisotropy. After annealing at 800-900~C for 2-4 h and HIP at 920~C/100MPa for 2 h, the brittle martensite could be transformed into ductile lamellar （a＋~） microstructure and the static tensile properties of SLM-processed Ti-6AI-4V alloys in the machined condition could be comparable to that of wrought materials. Even after HIP treatment, the as-built surfaces could decrease the ductility and reduction of area of SLM-processed fi-6AI-4V alloys to 9.2% and 20%, respectively. The crack initiation could occur at the columnar grain boundaries or at the as-built surfaces. The lamellar （a＋13） microstructures and columnar grains could hinder or distort the crack propagation path during tensile tests.

Effects of selective laser melting parameters on surface quality and densification behaviours of pure nickel

The effects of laser power and scanning speed on the forming characteristic of scanning tracks,densification behaviours and surface roughness of pure nickel fabricated with selective laser melting(SLM)were studied.The results indicate that the scanning tracks showed continuous,regular and flat surface with increasing laser power and decreasing scanning speed in a specific range,which could avoid the defects(like holes and balling structures)forming in SLM processing.The optimal process window was identified as the scanning speed of 900 mm/s and the laser power of 255−275 W by comparing the surface qualities and densification behaviours.With the suitable processing parameters,the relative density could achieve 99.16%,the tensile strength was(359.49±2.74)MPa,and the roughnesses of the top and side surfaces were(12.88±2.23)and(14.98±0.69)μm,respectively.

Experimental study on mechanism of influence of laser energy density on surface quality of Ti-6Al-4V alloy in selective laser melting

This experiment obtained different laser energy density(LED) by changing SLM molding process parameters.The surface morphology, surface quality, and microstructure of as-fabricated samples were studied. The effects of scanning speed, hatching space, and laser power on surface quality were analyzed, and the optimal LED range for surface quality was determined. The results show that pores and spherical particles appear on the sample’s surface when low LED is applied, while there are lamellar structures on the sides of the samples. Cracks appear on the sample’s surface,and the splash phenomenon increases when a high LED is taken. At the same time, a large amount of unmelted powder adhered to the side of the sample. The surface quality is the best when the LED is 150-170 J/mm^(3). The preferred hatch space is currently 0.05-0.09 mm, the laser power is 200-350 W, and the average surface roughness value is(15.1±3) μm.The average surface hardness reaches HV404±HV3, higher than the forging standard range of HV340-HV395.Increasing the LED within the experiment range can increase the surface hardness, yet an excessively high LED will not further increase the surface hardness. The microstructure is composed of needle-like α’-phases with a length of about 20μm, in a crisscross ‘N’ shape, when the LED is low. The β-phase grain boundary is not obvious, and the secondaryphase volume fraction is high;when the LED is high, the α’-phase of the microstructure is in the form of coarse slats, and the secondary-phase is composed of a small amount of secondary α’-phase, the tertiary α’-phase and the fourth α’-phase disappear, and the volume fraction of the secondary-phase becomes low.

Surface modification of biomedical Mg-Ca and Mg-Zn-Ca alloys using selective laser melting: Corrosion behaviour, microhardness and biocompatibility

Magnesium alloys such as Mg–Ca and Mg–Zn–Ca are good orthopaedic materials;however their tendency to corrode is high.Herein we utilize selective laser melting(SLM)to modify the surface of these Mg alloys to simultaneously improve the corrosion behaviour and microhardness.The corrosion rate decreased from 2.1±0.2 mm/y to 1.0±0.1 mm/y for the laser-processed Mg–0.6Ca,and from 1.6±0.1 mm/y to 0.7±0.2 mm/y for laser-processed Mg–0.5Zn–0.3Ca.The microhardness increased from 46±1 HV to 56±1 HV for Mg–0.6Ca,and from 47±3 HV to 55±3 HV for Mg–0.5Zn–0.3Ca.In addition,good biocompatibility remained in the laser processed Mg alloys.The improved properties are attributed to laser-induced grain refinement,confined impurity elements,residual stress,and modified surface chemistry.The results demonstrated the potential of SLM as a surface engineering approach for developing advanced biomedical Mg alloys.

Effect of laser surface melting on surface integrity of Al-4.5Cu composites reinforced with SiC and MoS2

Two types of composites were prepared with Al-4.5Cu alloy as a matrix using stir casting method.One was reinforced with 10wt.%of Si C and 2wt.%of MoS2.The other was reinforced with 10wt.%of Si C and 4wt.%of MoS2.Their surfaces were remelted using a CO2 laser beam with an objective to study the influence of laser surface melting(LSM).The topography,microhardness,corrosion resistance and wear resistance of the laser melted surfaces were studied.Overall surface integrity after LSM was compared with as-cast surface.LSM enhanced the microhardness and wear resistance of the surface in each case.Porosity of the laser melted surface was low and corrosion resistance was high.Thus,LSM can be conveniently applied to enhancing the surface integrity of the aluminium composites.However,there is an optimum laser specific energy,around 38 J/m^2 in this study,for obtaining the best surface integrity.

Surface Integrity of Ultrasonically-Assisted Milled Ti6Al4V Alloy Manufactured by Selective Laser Melting

The Ti6Al4V parts produced by the existing selective laser melting(SLM)are mainly confronted with poor surface finish and inevitable interior defects,which substantially deteriorates the mechanical properties and performances of the parts.In this regard,ultrasonically-assisted machining(UAM)technique is commonly introduced to improve the machining quality due to its merits in increasing tool life and reducing cutting force.However,most of the previous studies focus on the performance of UAM with ultrasonic vibrations applied in the tangential and feed directions,whereas few of them on the impact of ultrasonic vibration along the vertical direction.In this study,the effects of feed rate on surface integrity in ultrasonically-assisted vertical milling(UAVM)of the Ti6Al4V alloy manufactured by SLM were systemically investigated compared with the conventional machining(CM)method.The results revealed that the milling forces in UAVM showed a lower amplitude than that in CM due to the intermittent cutting style.The surface roughness values of the parts produced by UAVM were generally greater than that by CM owing to the extra sinusoidal vibration textures induced by the milling cutter.Moreover,the extra vertical ultrasonic vibration in UAVM was beneficial to suppressing machining chatter.As feed rate increased,surface microhardness and thickness of the plastic deformation zone in CM raised due to more intensive plastic deformation,while these two material properties in UAVM were reduced owing to the mitigated impact effect by the high-frequency vibration of the milling cutter.Therefore,the improved surface microhardness and reduced thickness of the subsurface deformation layer in UAVM were ascribed to the vertical high-frequency impact of the milling cutter in UAVM.In general,the results of this study provided an in-depth understanding in UAVM of Ti6Al4V parts manufactured by SLM.

Effects of laser surface melting on crystallographic texture, microstructure, elastic modulus and hardness of Ti-30Nb-4Sn alloy

The biocompatibility of orthopedic implants is closely related to their elastic modulus and surface properties.The objective of this study was to determine the effects of cold rolling,recrystallization and laser surface melting(LSM)on the microstructure and mechanical properties of a biphase(α″+β)Ti-30Nb-4Sn alloy.X-ray diffraction(XRD)texture analysis of the cold-rolled substrate revealed the[302]α″//ND texture component,while analysis of the recrystallized substrate showed the[302]α″//ND and[110]α″//ND components.Theβ-phase texture could not be directly measured by XRD,but the presence of the[111]β//ND texture component was successfully predicted by considering the orientation relationship between theα″andβphases.Nanoindentation measurements showed that the elastic modulus of the cold-rolled substrate(63GPa)was lower than that of the recrystallized substrate(74GPa).Based on the available literature and the results presented here,it is suggested that this difference is caused by the introduction of crystal defects during cold deformation.The combined nanoindentation/EBSD analysis showed that the nanoindentation results are not affected by crystal orientation.LSM of the deformed alloy produced changes in hardness,elastic modulus and crystallographic texture similar to those produced by recrystallization heat treatment,creating a stiffness gradient between surface and substrate.

Nickel-based superalloy architectures with surface mechanical attrition treatment: Compressive properties and collapse behaviour

Surface modifications can introduce natural gradients or structural hierarchy into human-made microlattices,making them simultaneously strong and tough.Herein,we describe our investigations of the mechanical properties and the underlying mechanisms of additively manufactured nickel–chromium superalloy(IN625)microlattices after surface mechanical attrition treatment(SMAT).Our results demonstrated that SMAT increased the yielding strength of these microlattices by more than 64.71%and also triggered a transition in their mechanical behaviour.Two primary failure modes were distinguished:weak global deformation,and layer-by-layer collapse,with the latter enhanced by SMAT.The significantly improved mechanical performance was attributable to the ultrafine and hard graded-nanograin layer induced by SMAT,which effectively leveraged the material and structural effects.These results were further validated by finite element analysis.This work provides insight into collapse behaviour and should facilitate the design of ultralight yet buckling-resistant cellular materials.

Crack elimination and strength enhancement mechanisms of selective laser melted Si-modified Al−Mn−Mg−Er−Zr alloy

In order to increase the processability and process window of the selective laser melting(SLM)-fabricated Al−Mn−Mg−Er−Zr alloy,a novel Si-modified Al−Mn−Mg−Er−Zr alloy was designed.The effect of Si alloying on the surface quality,processability,microstructure,and mechanical properties of the SLM-fabricated alloy was studied.The results showed that introducing Si into the Al−Mn−Mg−Er−Zr alloy prevented balling and keyhole formation,refined the grain size,and reduced the solidification temperature,which eliminated cracks and increased the processability and process window of the alloy.The maximum relative density of the SLM-fabricated Si/Al−Mn−Mg−Er−Zr alloy reached 99.6%.The yield strength and ultimate tensile strength of the alloy were(371±7)MPa and(518±6)MPa,respectively.These values were higher than those of the SLM-fabricated Al−Mn−Mg−Er−Zr and other Sc-free Al−Mg-based alloys.

Hierarchical microstructures with high spatial frequency laser induced periodic surface structures possessing different orientations created by femtosecond laser ablation of silicon in liquids

High spatial frequency laser induced periodic surface structures(HSFLs)on silicon substrates are often developed on flat surfaces at low fluences near ablation threshold of 0.1 J/cm2,seldom on microstructures or microgrooves at relatively higher fluences above 1 J/cm^2.This work aims to enrich the variety of HSFLs-containing hierarchical microstructures,by femtosecond laser(pulse duration:457 fs,wavelength:1045 nm,and repetition rate:100 kHz)in liquids(water and acetone)at laser fluence of 1.7 J/cm^2.The period of Si-HSFLs in the range of 110–200 nm is independent of the scanning speeds(0.1,0.5,1 and 2 mm/s),line intervals(5,15 and 20μm)of scanning lines and scanning directions(perpendicular or parallel to light polarization direction).It is interestingly found that besides normal HSFLs whose orientations are perpendicular to the direction of light polarization,both clockwise or anticlockwise randomly tilted HSFLs with a maximal deviation angle of 50°as compared to those of normal HSFLSs are found on the microstructures with height gradients.Raman spectra and SEM characterization jointly clarify that surface melting and nanocapillary waves play important roles in the formation of Si-HSFLs.The fact that no HSFLs are produced by laser ablation in air indicates that moderate melting facilitated with ultrafast liquid cooling is beneficial for the formation of HSFLs by LALs.On the basis of our findings and previous reports,a synergistic formation mechanism for HSFLs at high fluence was proposed and discussed,including thermal melting with the concomitance of ultrafast cooling in liquids,transformation of the molten layers into ripples and nanotips by surface plasmon polaritons(SPP)and second-harmonic generation(SHG),and modulation of Si-HSFLs direction by both nanocapillary waves and the localized electric field coming from the excited large Si particles.

Microstructure and surface texture driven improvement in in-vitro response of laser surface processed AZ31B magnesium alloy

The present work explored effects of laser surface melting on microstructure and surface topography evolution in AZ31B magnesium alloy.Thermokinetic effects experienced by the material during laser surface melting were simulated using a multiphysics finite element model.Microstructure and phase evolution were examined using scanning electron microscopy,X-ray diffraction,and electron back scatter diffraction.Surface topography was evaluated using white light interferometry.The interaction of surface melted samples with simulated body fluid was monitored by contact angle measurements and immersion studies up to 7 days.Laser surface melting led to formation of a refined microstructure with predominantly basal crystallographic texture.Concurrently,the amount ofβphase(Mg_(17)Al_(12))increased with an increase in the laser fluence.βphase preferentially decorated the cell boundaries.In terms of topography,the surface became progressively rougher with an increase in laser fluence.As a result,upon immersion in simulated body fluid,the laser surface melted samples showed an improved wettability,corrosion resistance,and precipitation of mineral having composition closer to the hydroxyapatite bone mineral compared to the untreated sample.

Corrosion resistance of pulsed laser modified AZ31 Mg alloy surfaces

The effect of laser surface melting on the corrosion resistance of AZ31 Mg alloy in 0.1 M NaCl solution was investigated using different laser processing conditions(energy densities of 14 and 17 J cm^(-2)).Laser treatment induced rough surfaces primarily composed of oxidized species of Mg.XPS analysis revealed that the surface concentration of Al increased significantly as a consequence of LSM.Electrochemical impedance spectroscopy showed that the laser treatment remarkably increased the polarization resistance of the AZ31 Mg alloy and induced a passive-like region of about 100 mV,as determined by potentiodynamic polarization.Analysis of the results obtained provide solid evidence that within the immersion times used in this study,LSM treatment increased the corrosion resistance of AZ31 Mg alloy under open circuit conditions and anodic polarization.

Microstructures of surface modification layer on Q235 steel produced by laser melt injection of WC

WC powder was injected onto the surface of Q235 steel by laser melt injection (LMI). The influence of process parameters was studied. The microstructure and composition of the coatings were analyzed by SEM, XRD and EDS. The hardness and wear-resistant property of the coatings and Q235 steel were measured. The results show that LMI layer can be achieved only under the condition that process parameters meet the strict requirements. By optimizing the process parameter, excellent coatings can be acquired by injecting WC powder onto the surface of Q235 steel. The microstructure in the coatings is complex, which consists of WC, W2C and M6C(Fe3W3C-Fe4W2C) phases. The difference of Fe3W3C microstructure in different zones of the coatings is obvious. Both the compositions of the reaction layers around the particle and dendrite precipitation carbides in the upper coating are Fe3W3C. The average hardness of LMI layer is above HV 900, which is about four times that of Q235 steel. The friction coefficient of LMI layer is only one quarter that of the substrate, which indicates that the wear resistance of the coatings is enhanced sharply.

Study on microstructure and properties of laser surface melted layer of AZ31B magnesium alloy

An attempt has been made to improve the surface properties of AZ31B magnesium alloy through solid solution hardening and refinement of microstructures using a CO2 laser as a heat generating source. X-ray diffraction （XRD） was used to identify the phases. Microstructure and properties of laser melted layer of AZ31B magnesium alloy were observed or tested by means of optical microscope （OM）, scanning electron microscope （SEM）, micro-hardness equipment and electrochemical corrosion equipment etc. The results show that the microstructure of laser melted layer becomes finer significantly and uniform. Compared with the substrate, the content of β-Mg17 Al12 phase of melted layer decreases comparatively. Microhardness of the laser melted layer is improved to 50 -95 HV0. 05 as compared to 40 -45 HV0.05 of the AZ31B Mg alloy substrate. The results of electrochemical corrosion show that the corrosion resistance of laser surface melted layer has been improved.

Process analysis of direct laser melting to fabricate layered hybrid beads

The successful fabrication of layered hybrid beads by DLM process is limited by dissimilar melting ranges of different powders.For the application of DLM process into manufacturing industries,target mechanical properties of final product must be achieved.Process analysis was performed for the DLM fabrication of layered hybrid beads by using stainless steel (SS 316L) and titanium powders.For the analysis of fabrication characteristics,single hybrid bead was formed using SS316L powder onto the base plate and then Ti powder was melted onto the previous melted layer.In addition,multi-layer hybrid beads were fabricated for the analysis of the layering effects between them.From these studies,the effects of the processing parameters,such as laser power,scan rate and scan line spacing on surface morphology were characterized and optimum processing conditions for the DLM fabrication of layered hybrid beads were developed.

Laser Surface Modification of Lean-alloyed Austenitic Stainless Steel for Corrosion Resistance

In order to reduce the cost of the austenitic stainless steels(ASSs),the expensive austenite former(nickel) is often substituted by manganese.However,manganese is generally seen to have a detrimental effect on the corrosion resistance.In the present study,the feasibility of laser surface modification of a lean-alloyed ASS(FeCrMn) for enhancing pitting corrosion resistance was investigated.Laser surface modification of FeCrMn was successfully achieved by a 2.3 kW high power diode laser(HPDL).Cyclic polarization tests for FeCrMn after laser surface modification in 3.5% NaCl solution at 25 ℃ were performed by using a potentiostat.The pitting resistance of the laser-modified specimens was found to be significantly improved as reflected by the noble shift in pitting potential.This could be attributed to redistribution of manganese sulphide leading to a more homogenous and refined microstructure.Pitting corrosion resistance of the laser-treated FeCrMn followed by subsequent citric acid passivation was found to be further improved as reflected by the noble shift in pitting potential to 0.18 V.

Surface Characterization of Laser Surface Melted NiTi Shape Memory Alloy in Hanks' Solution

The surface of Ti-50.8Ni at% shape memory alloy was melted by an Nd-YAG laser. The Ti/Ni and Ti4+/Ti atomic concentration ratios at the surface were changed significantly. The Ni ion release rate of the laser melted surface was much lower than that of the mechanical polished samples. A calcium-phosphorous layer with high Ca/P ratio was detected after immersion in Hanks’ solution.

激光熔凝处理对P20钢组织及性能的影响

目的提高P20模具钢的表面硬度和耐磨性能。方法采用激光熔凝技术对P20模具钢表面进行强化处理。通过硬度梯度检测和摩擦磨损测试,分别评价熔凝层的硬度分布特征和耐磨性能,并通过光学显微镜和扫描电子显微镜对熔凝层及磨痕形貌进行分析。结果使用激光输出功率为500W、光斑直径为2.5mm、聚焦透镜距离为40 mm、扫描速度为6 mm/s、搭接率为45%、氮气保护的激光熔凝工艺所得熔凝层的组织细小,无脱碳、畸变、裂纹等缺陷,熔凝处理质量高。熔凝过程中单道激光熔凝层呈半椭圆形分布,最大深度为610~620μm。熔凝处理后表面硬度提升显著,熔凝层的硬度分布与熔凝层的区域位置有关,具有较高硬度且硬度保持基本稳定的熔凝层深度约为400μm;单道激光熔凝层最高硬度可达460~480HV,重叠影响区即双熔凝区的最高硬度在540~560HV之间,即熔凝层硬度普遍较基体硬度提高了60%以上。此外,P20模具钢经过激光熔凝处理后耐磨性能提升明显,其平均摩擦因数约为0.85,熔凝处理的磨损失重较未处理的试样减少了约61%,其磨损机制主要表现为磨粒磨损和少量的黏着磨损或剥落脱离。结论激光熔凝处理能够显著提高P20模具钢的表面硬度和耐磨性能,试验采用的激光熔凝工艺可在P20钢表面获得硬度较高且稳定可靠的熔凝层深度在400μm左右,能将P20模具钢的表面硬度及耐磨性提高60%以上。