New Progress on All Solid State Laser Technology in China

1 Significance of All Solid State Laser (DPL) Technology in Field of LaserBecause of the advantages of high conversion efficiency, good beam quality, small size and light weight, DPL becomes the hotspot and priority of development of laser technology. It may be the main body of laser in the future and replace gas laser and liquid laser. It is a great revolution of laser technology.The developed countries vie in developing DPL. China has achieved great success in this field, but there is a wide gap between the developed countries and us. We should attach great importance to it.

Infrared Laser Pumped Green and Blue Laser Emissions from a Single Solid State Material Doped by Rare Earth Ions

The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared laser pumped rare earth doped nonlinear laser crystals by means of self frequency conversion and from infrared laser pumped rare earth doped bulk, fiber and microsphere materials by means of frequency upconversion are introduced in detail. Other kinds of devices and methods are also compared. The typical nonlinear laser crystals such as YAl 3(BO 3) 4, GdAl 3(BO 3) 4, YCa 4O(BO 3) 3 , GdCa 4O(BO 3) 3, and the typical upconversion fluoride fibers are compared and analyzed. The major problems remaining to be solved and the developing trends in the area are also discussed.

Thermal Analysis of Blue Laser Diode for Solid State Lighting Application

Solid-state light sources based on laser diode are becoming great alternative for LEDs. Improvement of the thermal characteristics of InGaN LD is very important for realizing reliable devices. In this investigation the influence of the temperature of diode on light parameters was studied. White light was obtained by coupling blue light of diode with yellow phosphors: YAG:Ce3+ and GYAG:Ce3+ with nitride. For three values of the temperature of LD’s stem, regulated by Peltier module, CCT, CRI and chromaticity coordinates were measured by spectroradiometer. The importance of emission characteristics of materials was shown. Subsequently, the influence of temperature on laser diode intensity was investigated for 120 hours. This experiment was repeated for different levels of current and temperature. Finally, the steady state of thermal finite element analysis was performed to reveal the distribution of the temperature. The analysis showed the importance of heat sink and also temperature control.

Superplastic solid state welding of steel and copper alloy based on laser quenching of steel surface

Based on the feasibility of isothermal superplastic solid state welding of steel and copper alloy, the welded surface of steel surface was ultra-fined through laser quenching, and then the welding process tests between different base metals of 40Cr and QCr0.5 were made under the condition of non vacuum and non shield gas. The experimental results show that, with the sample surface of steel after laser quenching and that of copper alloy carefully cleaned, and under the pre-pressed stress of 56.684.9 MPa, at the welding temperature of 750800 ℃ and at initial strain rate of （2.57.5）×10-4 s-1, the solid state welding can be finished in 120180 s so that the strength of the joint is up to that of QCr0.5 base metal and the expansion rate of the joint does not exceed 6%. The plastic deformation of the joint was further analysed. The superplastic deformation of the copper alloy occurs in welding process and the deformation of steel are little.

Energy transfer in solid-state dye lasers based on methyl methacrylate co-doped with sulforhodamine B and crystal violet

Laser action in methyl methacrylate （MMA） co-doped with sulforhodamine B and crystal violet dyes was investi- gated. The dye mixture was incorporated into a solid polymeric matrix and was pumped by a 532-nm Nd：YAG laser. Distributed feedback dye laser （DFDL） action was induced in the dye mixture using a prism arrangement both in the donor and acceptor regions by an energy transfer mechanism. Theoretically, the characteristics of acceptor and donor DFDLs, and the dependence of their pulse widths and output powers on acceptor-donor concentrations and pump power, were studied. Experimentally, the output energy of DFDL was measured at the emission peaks of donor and acceptor dyes for different pump powers and different acceptor-donor concentrations. Tuning of the output wavelength was achieved by varying the period of the gain modulation of the laser medium. The laser wavelength showed continuous tunability from 563 nm to 648 nm.

Analytical modelling of end thermal coupling in a solid-state laser longitudinally bonded by a vertical-cavity top-emitting laser diode

The intrinsic features involving a circularly symmetric beam profile with low divergence, planar geometry as well as the increasingly enhanced power of vertical-cavity surface-emitting lasers （VCSELs） have made the VCSEL a promising pump source in direct end bonding to a solid-state laser medium to form the minimized, on-wafer integrated laser system. This scheme will generate a surface contact pump configuration and thus additional end thermal coupling to the laser medium through the joint interface of both materials, apart from pump beam heating. This paper analytically models temperature distributions in both VCSEL and the laser medium from the end thermal coupling regarding surface contact pump configuration using a top-emitting VCSEL as the pump source for the first time. The analytical solutions are derived by introducing relative temperature and mean temperature expressions. The results show that the end contact heating by the VCSEL could lead to considerable temperature variations associated with thermal phase shift and thermal lensing in the laser medium. However, if the central temperature of the interface is increased by less than 20 K, the end contact heating does not have a significant thermal influence on the laser medium. In this case, the thermal effect should be dominated by pump beam heating. This work provides useful analytical results for further analysis of hybrid thermal effects on those lasers pumped by a direct VCSEL bond.

Medium performance effect on the high output energy from a xenon lamp-pumped pyrromethene-567 solid-state dye laser

In order to obtain a high output energy from a xenon lamp-pumped solid-state dye laser, homogeneities of laser mediums and flatnesses of medium faces with different processing treatments are discussed in the paper. The mediums without aging treatment, which are prepared by using a prepolymer process and have diamond-machined end faces to produce the required optical finish, give a highest laser output of 281.9 mJ with 0.215% slope efficiency at 2.0x 10^-4 mol/L. The best medium lifetime is 21 shots to 50% of original output equating 74.6 k J/liter.

An all-solid-state high power quasi-continuous-wave tunable dual-wavelength Ti：sapphire laser system using birefringence filter

This paper describes a tunable dual-wavelength Ti：sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd：YAG laser as the pumping source, and the birefringence filter as the tuning element. Tunable dual-wavelength outputs with one wavelength range from 700 nm to 756.5 nm, another from 830 nm to 900mn have been demonstrated. With a pump power of 23 W at 532 nm, a repetition rate of 7 kHz and a pulse width of 47.6 ns, an output power of 5.1 W at 744.8 nm and 860.9 nm with a pulse width of 13.2 ns and a line width of 3 nm has been obtained, it indicates an optical-to-optical conversion efficiency of 22.2%.

A review of Al-based material dopants for high-performance solid state lithium metal batteries

As the world transitions to green energy, there is a growing focus among many researchers on the requirement for high-efficient and safe batteries. Solid-state lithium metal batteries(SSLMBs) have emerged as a promising alternative to traditional liquid lithium-ion batteries(LIBs), offering higher energy density, enhanced safety, and longer lifespan. The rise of SSLMBs has brought about a transformation in energy storage, with aluminum(Al)-based material dopants playing a crucial role in advancing the next generation of batteries. The review highlights the significance of Al-based material dopants in SSLMBs applications, particularly its contributions to solid-state electrolytes(SSEs), cathodes, anodes,and other components of SSLMBs. Some studies have also shown that Al-based material dopants effectively enhance SSE ion conductivity, stabilize electrode and SSE interfaces, and suppress lithium dendrite growth, thereby enhancing the electrochemical performance of SSLMBs. Despite the above mentioned progresses, there are still problems and challenges need to be addressed. The review offers a comprehensive insight into the important role of Al in SSLMBs and addresses some of the issues related to its applications, endowing valuable support for the practical implementation of SSLMBs.

Controllable combustion behaviors of the laser-controlled solid propellant

Microsatellites have been widely applied in the fields of communication,remote sensing,navigation and science exploration due to its characteristics of low cost,flexible launch mode and short development period.However,conventional solid-propellant have difficulties in starting and interrupting combustion because combustion is autonomously sustained after ignition Herein,we proposed a new type of solid-propellant named laser-controlled solid propellant,which is sensitive to laser irradiation and can be started or interrupted by switching on/off the continuous wave laser.To demonstrate the feasibility and investigate the controllable combustion behaviors under different laser on/off conditions,the combus tion parameters including burning rate,ignition delay time and platform pressure were tested using pressure sensor,high-speed camera and thermographic camera.The results showed that the increase of laser-on or laser-off duration both will lead to the decrease of propellant combustion performance during re-ignition and re-combustion process.This is mainly attributed to the laser attenuation caused by the accumulation of combustion residue and the change of chamber ambient temperature.Simultaneously the multiple ignition tests revealed that the increased chamber ambient temperature after combustion can make up for the energy loss of laser attenuation and expansion of chamber cavity.However,the laser-controlled combustion performance of solid propellant displayed a decrease trend with the addi-tion of ignition times.Nevertheless,the results still exchibited good laser-controlled agility of laser-controlled solid propellant and manifested its inspiring potential in many aspects of space missions.

Research on All-solid-state Laser and Its Industrial Development in China

Some typical applications of solid-state laser are described, and its industrial development in China are also introduced in detail.

Development and Research on All-solid-state Intracavity Sum-frequency laser

Generation of intracavity multi-wavelength and the basic principle of sum-frequency lasers are discused, and the current research status and development of laser diode pumped lasers are introduced in detail.

Performance of gain-switched all-solid-state quasi-continuous-wave tunable Ti:sapphire laser system

We have made a gain-switched all-solid-state quasi-continuous-wave （QCW） tunable Ti：sapphire laser system, which is pumped by a 532 nm intracavity frequency-doubled Nd：YAG laser. Based on the theory of gain-switching and the study on the influencing factors of the output pulse width, an effective method for obtaining high power and narrow pulse width output is proposed. Through deliberately designing the pump source and the resonator of the Ti：sapphire laser, when the repetition rate is 6 kHz and the length of the cavity is 220 mm, at an incident pump power of 22 W, the tunable Ti：sapphire laser from 700 to 950nm can be achieved. It has a maximum average output power of 5.6W at 800nm and the pulse width of 13.2 ns, giving an optical conversion efficiency of 25.5% from the 532 mn pump laser to the Ti：sapphire laser.

Absorption of ultrashort intense lasers in laser–solid interactions

With the advent of ultrashort high intensity laser pulses, laser absorption during the laser–solid interactions has received significant attention over the last two decades since it is related to a variety of applications of high intensity lasers,including the hot electron production for fast ignition of fusion targets, table-top bright X-ray and gamma-ray sources,ion acceleration, compact neutron sources, and generally the creation of high energy density matters. Normally, some absorption mechanisms found for nanosecond long laser pulses also appear for ultrashort laser pulses. The peculiar aspects with ultrashort laser pulses are that their absorption depends significantly on the preplasma condition and the initial target structures. Meanwhile, relativistic nonlinearity and ponderomotive force associated with the laser pulses lead to new mechanisms or phenomena, which are usually not found with nanosecond long pulses. In this paper, we present an overview of the recent progress on the major absorption mechanisms in intense laser–solid interactions, where emphasis is paid to our related theory and simulation studies.

Microstructure and mechanical properties of Mg-Zn-Y-Zr alloy prepared by solid state recycling

Machined chips of Mg-Zn-Y-Zr alloy were consolidated by cold pressing and then hot extrusion under various processing temperatures and extrusion ratios. The results show that the microstructure of the chip-extruded alloy is marked by a large number of recrystallized grains and some unrecrystallized grains, which results in high strength but low ductility at temperatures below 320 ℃. With increasing processing temperature up to 360 ℃, entirely recrystallized and equiaxed grains are obtained. Mg-Zn-Y-Zr alloy with low strength but high ductility is obtained compared with the alloy processed at low temperature. At 420℃, coarse and equiaxed grains are formed, which results in the drastic decrease of mechanical properties. With increasing extrusion ratio from 8 to 16, the grain refinement is more obvious and the mechanical properties at room temperature are improved effectively. However, the yield strength and ultimate tensile strength are improved a little with further increasing extrusion ratio.

Heat-treated microstructure and mechanical properties of laser solid forming Ti-6Al-4V alloy

The effects of heat treatment on the microstructure and mechanical properties of laser solid forming （LSF） Ti-6Al-4V alloy were investigated The influences of the temperature and time of solution treatment and aging treatment were analyzed. The results show that the microstructure of LSFed samples consists of Widmanstatten α laths and a little acicular in columnar prior β grains with an average grain width of 300 μm, which grow epitaxiaUy from the substrate along the deposition direction （27）. Solution treatment had an important effect on the width, aspect ratio, and volmne fraction of primary and secondary a laths, and aging treatment mainly affects the aspect ratio and volume fraction of primary α laths and the width and volume fraction of secondary a laths. Globular a phase was first observed in LSFed samples when the samples were heat treated with solution treatment （950℃, 8 h/air cooling （AC）） or with solution treatment （950℃, 1 h/AC） and aging treatment （550℃, above 8 h/AC）, respectively. The coarsening and globularization mechanisms of a phase in LSFed Ti-6Al-4V alloy during heat treatment were presented. To obtain good integrated mechanical properties for LSFed Ti-6Al-4V alloys, an optimized heat treatment regimen was suggested.

Effect of Intermediate Heat Treatment Temperature on Microstructure and Notch Sensitivity of Laser Solid Formed Inconel 718 Superalloy

Inconel 718 superalloys deposited by laser solid forming （LSF） were heat treated with solution treatment,intermediate heat treatment （IHT） and two-stage aging treatment in sequence （SITA heat treatment）.The effect of IHT temperature on microstructure,tensile property and notch sensitivity of LSFed Inconel 718 superalloy at 500 ℃ were investigated.As-deposited columnar grains have transformed to equiaxed grains and the grains were refined due to the recrystallization during the SITA heat treatment.It is found that the size and amount of δ phase dispersed at grain boundaries decreased with the increasing of IHT temperature,and δ phase disappeared when the IHT temperature reached 1 020 ℃.The ultimate tensile strength （UTS） and yield strength （YS） of smooth samples increased to a maximum when the IHT temperature reached 980 ℃ and then decreased slightly to a minimum when the IHT temperature was 1 000 ℃,and followed by slight increasing again till the IHT temperature reached 1 020 ℃,resulted from the competition of precipitation strengthening effect of γ″ and γ＇ phase and the grain boundary weakening effect caused by the gradual disappearance of δ phase with increasing the IHT temperature.The notch sensitivity factor （qe） decreased but still greater than 1 as the IHT temperature increased,which is attributed to the decrease of the size and amount of δ precipitation.

Supercritical-hydrothermal accelerated solid state reaction route for synthesis of LiMn_2O_4 cathode material for high-power Li-ion batteries

Synthesis of the spinel structure lithium manganese oxide （LiMn2O4） by supercritical hydrothermal （SH） accelerated solid state reaction （SSR） route was studied. The impacts of the reaction pressure, reaction temperature and reaction time of SH route, and the calcination temperature of SSR route on the purity, particle morphology and electrochemical properties of the prepared LiMn2O4 materials were studied. The experimental results show that after 15 min reaction in SH route at 400 ℃ and 30 MPa, the reaction time of SSR could be significantly decreased, e.g. down to 3 h with the formation temperature of 800 ℃, compared with the conventional solid state reaction method. The prepared LiMn2O4 material exhibits good crystallinity, uniform size distribution and good electrochemical performance, and has an initial specific capacity of 120 mA.h/g at a rate of 0.1C （1C=148 mA/g） and a good rate capability at high rates, even up to 50C.

Stimulated photoluminescence emission and trap states in Si/SiO_2 interface formed by irradiation of laser

Stimulated photoluminescence （PL） emission has been observed from an oxide structure of silicon when optically excited by a radiation of 514nm laser. Sharp twin peaks at 694 and 692nm are dominated by stimulated emission, which can be demonstrated by its threshold behaviour and linear transition of emission intensity as a function of pump power. The oxide structure is formed by laser irradiation on silicon and its annealing treatment. A model for explaining the stimulated emission is proposed, in which the trap states of the interface between an oxide of silicon and porous nanocrystal play an important role.

Analytical and numerical investigations of displaced thermal state evolutions in a laser process

We investigate how displaced thermal states （DTSs） evolve in a laser channel. Remarkably, the initial DTS, an example of a mixed state, still remains mixed and thermal. At long times, they finally decay to a highly classical thermal field only related to the laser parameters κ and g. The normal ordering product of density operator of the DTS in the laser channel leads to obtaining the analytical time-evolution expressions of the photon number, Wigner function, and von Neumann entropy. Also, some interesting results are presented via numerically investigating these explicit time-dependent expressions.